Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (62) (entfernen)
Referierte Publikation
- nein (62) (entfernen)
Schlagworte
- Additive manufacturing (13)
- Neutron Diffraction (12)
- Additive Manufacturing (10)
- Computed tomography (9)
- Residual Stress (8)
- X-ray refraction (8)
- Composites (7)
- Porosity (7)
- Residual stress (7)
- Computed Tomography (6)
- Microcracking (6)
- Anisotropy (4)
- Imaging (4)
- Neutron diffraction (4)
- Additive Fertigung (3)
- Computertomographie (3)
- Mechanical Properties (3)
- Microstructure (3)
- Non-destructive testing (3)
- Non-linear stress-strain (3)
- Röntgenrefraktion (3)
- Selective laser melting (3)
- Synchrotron X-ray diffraction (3)
- Zerstörungsfreie Prüfung (3)
- 3D Mikrostruktur (2)
- Ammonium nitrate (2)
- Analytical Science (2)
- Ceramics (2)
- Damage (2)
- Defects (2)
- Fatigue (2)
- Hydrogen assisted cracking (2)
- Laser beam melting (2)
- Metals (2)
- Metrologie (2)
- Neutronenbeugung (2)
- Non-destructive characterisation (2)
- Phase grating (2)
- Prill (2)
- Specific surface area (2)
- TF Material (2)
- Talbot- Lau interferometry (2)
- Ti-6Al-4V (2)
- X-ray Refraction (2)
- X-ray computed tomography (2)
- X-ray diffraction (2)
- X-ray refraction techniques (2)
- 3D rendering (1)
- Alloys (1)
- Aluminium matrix (1)
- Aluminum Titanate (1)
- Aluminum alloys (1)
- Analyser-based imaging (1)
- Asphalt, porosity (1)
- BAM (1)
- Beta-eucrytite (1)
- Blasting (1)
- Calcium phosphate (1)
- Cearmics (1)
- Ceria (1)
- Characterization (1)
- Coating (1)
- Composite (1)
- Composite materials (1)
- Concrete (1)
- Cordierite (1)
- Crack segmentation (1)
- Cracks (1)
- Creep (1)
- Creep models (1)
- Crystal structure (1)
- Diesel Particulate Filter Materials (1)
- Diffraction (1)
- Directional interface variance analysis (DIVA) (1)
- Duplex stainless steel (1)
- EBSD (1)
- Eigenspannungen (1)
- Elastic Constants (1)
- Energetic systems (1)
- Engineering applications (1)
- Explosives (1)
- Extrusion (1)
- FFT periodogram (1)
- IN718 (1)
- Image Analysis (1)
- Implants (1)
- In-situ CT (1)
- In-situ heating up to 1400°C (1)
- In718 (1)
- Inconel (1)
- Influence of rheology modifying admixtures on hydration of cementitious suspensions (1)
- Institut Laue Langevin (1)
- Intergranular strain (1)
- Interphase residual stress (1)
- Laboratory energy-dispersive X-ray diffraction (EDXRD) (1)
- Large Scale Facilities (1)
- Laser powder bed fusion (1)
- Lattice Structure (1)
- Lattice structure (1)
- Lattice structures (1)
- Lattices (1)
- Lightweight structures (1)
- MMC (1)
- Machine Learning (1)
- Machine learning (1)
- Manufacturing defects (1)
- Maskinteknik (1)
- Materials (1)
- Mechanical Engineering (1)
- Mechanical properties (1)
- Medical implants (1)
- Microstructure-property relations (1)
- Multiple-layered scaffold (1)
- Neutron and X-ray Diffraction (1)
- Non-destructive (1)
- Non-linear vibration (1)
- Nonel (1)
- On-line monitoring (1)
- Orientation (1)
- PBFLB/M AlSi10Mg alloy (1)
- Phase transformation (1)
- Phase-contrast X-ray imaging (1)
- Plasticity (1)
- Polycaprolactone (1)
- Pore orientation (1)
- Powder analysis (1)
- Preferred orientation (1)
- Refraction radiography (1)
- Refraction tomography (1)
- Refractory materials (1)
- Refraktion (1)
- Residual Stress analysis (1)
- Roughness (1)
- SEM (1)
- SLM (1)
- Scaffold (1)
- Shock wave (1)
- Small Angle Neutron Scattering (1)
- Stress analysis (1)
- Stress exponent (1)
- Stress-relief heat-treatments (1)
- Structural simulation (1)
- Surface roughness (1)
- Synchrotron (1)
- Synchrotron X-ray computed tomography (1)
- Synchrotron X-ray diffraction (SXRD) (1)
- Synchrotron X-ray refraction (1)
- Synchrotron computed tomography (1)
- Synchrotron radiation (1)
- Synchrotron µCT and refraction radiography (1)
- TEM (1)
- Thermal (1)
- Thermography (1)
- Tomographie (1)
- Visibility (1)
- Wall thickness (1)
- Water uptake (1)
- Welding (1)
- X-ray (1)
- X-ray Computed Tomography (1)
- X-ray Computed tomography (1)
- X-ray Refaction radiography (1)
- X-ray refraction radiography (1)
- Zirconia (1)
- grating (1)
- refraction (1)
- topography (1)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (40)
- 8.5 Röntgenbildgebung (39)
- 9 Komponentensicherheit (3)
- 9.4 Integrität von Schweißverbindungen (3)
- 2 Prozess- und Anlagensicherheit (2)
- 5 Werkstofftechnik (2)
- 5.0 Abteilungsleitung und andere (2)
- 9.2 Versuchsanlagen und Prüftechnik (2)
- 2.2 Prozesssimulation (1)
- 2.5 Konformitätsbewertung Explosivstoffe/Pyrotechnik (1)
Eingeladener Vortrag
- nein (34)
The stress–strain behavior of certain ceramics, such as aluminum titanate (AT, Al2TiO5), has features that are unusual for brittle material. In particular, a substantial nonlinearity under uniaxial tension, and load–unload hysteresis caused by the increase of the incremental stiffness at the beginning of unloading. These features are observed experimentally and attributed to microcracking. In this study, we investigate the mechanical response of an AT material at room and high temperature. Microstructure and microcracking are analyzed by means of electron microscopy, and both synchrotron micro computed tomography (µCT) and refraction radiography (SXRR). Synchrotron refraction radiography is combined with in-situ heating at high-temperatures (up to 1400°C) to be able to monitor the relative closure of microcracks as a function of increasing/decreasing temperatures.
The experimental determination of residual stress becomes more complicated with increasing complexity of the structures investigated. Unlike the conventional and most of the additive manufacturing (AM) fabrication techniques, laser powder bed fusion (PBF-LB) allows the production of complex structures without any additional manufacturing step. However, due to the extremely localized melting and solidification, internal stress-induced deformation and cracks are often observed. In the best case, significant residual stress is retained in the final structures as a footprint of the internal stress during manufacturing.
Here we report solutions to the most prevalent challenges when dealing with the diffraction-based determination of residual stress in AM structures, in particular the choice of the correct diffraction elastic constants. We show that for Nickel-based alloys, the diffraction elastic constants of AM material significantly deviate from their conventional counterparts. Furthermore, measurement strategies to overcome the hurdles appearing when applying diffraction-based techniques to complex-shaped lattice structures are presented: a) proper sample alignment within the beam, b) the proper determination of the residual stress field in a representative part of the structure (i.e., with an engineering meaning). Beyond the principal stress magnitude, the principal direcions of residual stress are discussed for different geometries and scan strategies, as they are relevent for failure criteria.
We show that the RS in the lattice struts can be considered to be uniaxial and to follow the orientation of the strut, while the RS in the lattice knots is more hydrostatic. Additionally, we show that strain measurements in at least seven independent directions are necessary for the correct estimation of the principal stress directions. The measurement directions should be chosen according to the sample geometry and to an informed choice on the possible strain field (i.e., reflecting the scan strategy).
We finally show that if the most prominent direction is not measured, the error in the calculated stress magnitude increases in such a manner that no reliable assessment of RS state can be made.
The determination of residual stress in additively manufactured materials is a challenge, even after decades from the establishment of the basics of residual stress analysis. This is due to the peculiar microstructure of such materials. In fact, researchers have discovered that conventional methods for the determination of RS in materials do not properly work for AM materials. In this tutorial, the basics of RS analysis will be explained, together with the basics of AM manufacturing techniques. The microstructure of the peculiar materials (AM) dealt with here will be elucidated. Successively, the necessary modifications to the conventional approaches to RS analysis will be explained and case studies will be displayed, for the attendant to touch with hands the peculiarities of the approaches. Finally, a few experimental and theoretical tips will be given on dos and don’ts for a correct determination of RS in AM materials.
The stress-induced tetragonal to monoclinic (t-m) zirconia phase transformation can provide a certain degree of plasticity to Ceria-stabilized (Ce-TZP) zirconia-based composites. Characterizing and monitoring this phase transition on a millimeter-size range, within the bulk and in-situ remains a challenge. In this work, the mechanical behavior of Ce-TZP based composite was studied in tension, combining microscopy and synchrotron Xray refraction techniques. In contrast with microscopy methods, which only provide surface information, X-ray refraction radiography (SXRR) allowed the visualization of all the transformation bands, over the entire length and thickness of tested specimens, opening up new avenues for in-situ stress-induced t-m transformation studies.
AbstractIn this study, we compare the residual stress state in a laser powder bed fusion (PBF‐LB/M) AlSi10Mg alloy in the as‐built (AB) condition with that after two different heat treatments (265 °C for 1 h, HT1; and 300 °C for 2 h, HT2). The bulk residual stress (RS) is determined using synchrotron X‐ray diffraction (SXRD), and near‐surface profiles are determined using laboratory energy‐dispersive X‐ray diffraction (EDXRD). The EDXRD results do not reveal any notable difference between the conditions at a depth of 350 μm, suggesting that the machining process yields a comparable residual stress state in the near‐surface regions. On the other hand, the SXRD results show that HT1 is more effective in relieving the bulk RS. It is observed that HT1 reduces the RS state in both the aluminium matrix and the silicon network. In addtion, HT2 does not have a significant impact on relaxing the RS as‐built state of the matrix, although it does induce a reduction in the RS magnitudes of the Si phase. It is concluded that the heat treatment stress relieving is effective as long as the Si‐network is not disaggregated.
A new titanium alloy improving the operation of implants additively manufactured and including laterally closed lattice structures is proposed. The new alloy possesses an increased affinity to the bone. The measured bone–interface implant (BII) of less than 10 mm and bone–implant contact (BIC) of 95% demonstrated an excellent osseointegration. Furthermore, since additive manufacturing naturally leads to a high-roughness surface finish, the wettability of the implant is increased. The combination of these factors is pushing ossification beyond its natural limits. In addition, the quality and speed of the ossification and osseointegration in/around laterally closed lattice implants open the possibility of bone spline key of prostheses. This enables the stabilization of the implant into the bone while keeping the possibility of punctual hooks allowing the implant to be removed more easily if required.
The overview of the activity of Federal Institute for Material Research and Testing (BAM, Belin, Germany) in the field of additively manufacturing material characterization will be presented. The research of our group is focused on the 3D imaging of AM materials by means of X-ray Computed Tomography at the lab and at synchrotron, and the residual stress characterization by diffraction (nondestructive technique). Also, two successful research project in collaboration with CAM2, Sweden are presented.
X-ray refraction is analogous to visible light deflection by matter; it occurs at boundaries between different media. The main difference between visible light and X-rays is that in the latter case deflection angles are very small, from a few seconds to a few minutes of arc (i.e., the refraction index n is near to 1). Importantly, deflection of X-rays is also sensitive to the orientation of the object boundaries. These features make X-ray refraction techniques extremely suitable to a) detect defects such as pores and microcracks and quantify their densities in bulk (not too heavy) materials, and b) evaluate porosity and particle properties such as orientation, size, and spatial distribution (by mapping). While X-ray refraction techniques cannot in general image single defects, they can detect objects with size above a few wavelengths of the radiation.
Such techniques, especially at the Synchrotron BESSY II, Berlin, Germany, can be used in-situ, i.e. when the specimen is subjected to temperatures or external loads.
The use of X-ray refraction analysis yields quantitative information, which can be directly input in kinetics, mechanical and damage models.
We hereby show the application of non-destructive X-ray refraction radiography (SXRR, 2D mapping also called topography) to problems in additive manufacturing:
1) Porosity analysis in PBF-LM-Ti64. Through the use of SXRR, we could not only map the (very sparse) porosity distribution between the layers and quantify it, but also classify, and thereby separate, the filled porosity (unmolten powder) from the keyhole and gas pores (Figure 1).
2) In-situ heat treatment of laser powder bed fusion PBF-LM-AlSi10Mg to monitor microstructure and porosity evolution as a function of temperature (Figure 2). By means of SXRR we indirectly observed the initial eutectic Si network break down into larger particles as a function of increasing temperature. We also could detect the thermally induced porosity (TIP). Such changes in the Si-phase morphology upon heating is currently only possible using scanning electron microscopy, but with a much smaller field-of-view. SXRR also allows observing the growth of some individual pores, usually studied via X-ray computed tomography, but again on much smaller fields-of-view.
Our results show the great potential of in-situ SXRR as a tool to gain in-depth knowledge of the defect distribution and the susceptibility of any material to thermally induced damage and/or microstructure evolution over statistically relevant volumes.
We discuss the non-linear stress–strain behavior of microcracked polycrystalline ceramics under uniaxial tension and compression (displacement control).
Micromechanics explanation and modeling of its basic features, such as non-linearity and hysteresis in stress–strain curves, are developed, with stable microcrack propagation and “roughness” of intergranular cracks playing critical roles in tension and crack sliding playing a critical role in compression. Experiments involving complex loading histories are explained, and themodel is shown to reproduce the basic features of the observed stress–strain curves.
Additively manufactured (AM) triply periodic metallic minimum surface structures (TPMSS, from the English Triply Periodic Minimum Surface Structures) fulfill several requirements in both biomedical and engineering fields: tunable mechanical properties, low sensitivity to manufacturing defects, mechanical stability, and high energy absorption. However, they also present some quality control challenges that may prevent their successful application. In fact, optimization of the AM process is impossible without considering structural features such as manufacturing accuracy, internal defects, and surface topography and roughness. In this study, quantitative nondestructive analysis of Ti-6Al-4V alloy TPMSS was performed using X-ray computed tomography (XCT). Several new image analysis workflows are presented to evaluate the effects of buildup direction on wall thickness distribution, wall degradation, and surface roughness reduction due to chemical etching of TPMSS. It is shown that the fabrication accuracy is different for the structural elements printed parallel and orthogonal to the fabricated layers. Different strategies for chemical etching showed different powder removal capabilities and thus a gradient in wall thickness. This affected the mechanical performance under compression by reducing the yield stress. A positive effect of chemical etching is the reduction of surface roughness, which can potentially improve the fatigue properties of the components. Finally, XCT was used to correlate the amount of powder retained with the pore size of the TPMSS, which can further improve the manufacturing process.