Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
- 2017 (3) (entfernen)
Dokumenttyp
- Vortrag (2)
- Beitrag zu einem Tagungsband (1)
Sprache
- Englisch (3)
Referierte Publikation
- nein (3)
Schlagworte
- Low cycle fatigue (3) (entfernen)
Eingeladener Vortrag
- nein (2)
In recent years, the performance of heat resistant ferritic-martensitic steels under cyclic oxidation and cyclic mechanical loading has gained considerable attention. The growing contributions of renewable energy sources to electricity generation have triggered a shift from continuous (baseload) operation of conventional power plants towards cyclic or “flexible” operation, which is needed to stabilize the electric grids by balancing the highly variable renewable’s input.
Compared to the impressive amount of data on isothermal oxidation/corrosion and static
mechanical loading (creep) that was compiled over decades, only little and sometimes
contradictory information is so far available on the reaction of these alloys to cyclic
conditions. The latter may involve frequent transients or holds at intermediate temperatures, as well as shut-downs and start-ups with high temperature rates which result in cyclic mechanical loads (thermo-mechanical fatigue, TMF) and thermo-cyclic oxidation at variable temperature.
Our contribution will report on recent findings obtained within the framework of a junior
research group which investigates the oxidation and fatigue of the ferritic-martensitic grades P91, P92 and VM12 SHC under thermo-cyclic conditions. Cyclic oxidation tests are carried out in steam using different sample shapes (flat coupons, U-segments and rings taken from heat exchanger tubes). Special attention is paid to changes in the kinetics and the integrity and possible delamination/spalling of the oxide layers. Mechanical tests are carried out on material from real steam pipes with a focus on the softening behaviour and lifetime issues resulting from combined creep/TMF loadings. All experiments are carried out in the 300-620°C regime with temperature and load profiles that resemble typical loading scenarios in power plants and are complemented by detailed microstructural characterisation.
Gas turbines are widely used for a variety of purposes including power generation, compression or as jet engines in aircrafts. The critical components of a gas turbine are the high-pressure turbine blades which operate under severe conditions. These include thermo-mechanical loadings over temperatures ranging from room temperature up to 1100°C.
While a large number of constitutive models for single crystals have been proposed, most applications are restricted to special loading scenarios, temperature range and deformation mechanisms. In particular, a number of models are focused on pure creep. Only a few papers consider application of both creep and fatigue. Applications of the constitutive models to long-term stress relaxation are even scarcer. The new model assumes deformation-induced softening and can properly reproduce the viscous behavior at different time scales.
The model has been calibrated with the uniaxial tests at 800°C and 950°C in [001], [011] and [111] specimens of a nickel-basis superalloy. The predicted creep, short- and long-term relaxation and cyclic tests are in reasonable agreement with the experimental observations.
Gas turbines are widely used for a variety of purposes including power generation, compression or as jet engines in aircrafts. The critical components of a gas turbine are the high-pressure turbine blades which operate under severe conditions. These include thermo-mechanical loadings over temperatures ranging from room temperature up to 1100°C.
While a large number of constitutive models for single crystals have been proposed, most applications are restricted to special loading scenarios, temperature range and deformation mechanisms. In particular, a number of models are focused on pure creep. Only a few papers consider application of both creep and fatigue. Applications of the constitutive models to long-term stress relaxation are even scarcer. The new model assumes deformation-induced softening and can properly reproduce the viscous behavior at different time scales.
The model has been calibrated with the uniaxial tests at 800°C and 950°C in [001], [011] and [111] specimens of a nickel-basis superalloy. The predicted creep, short- and long-term relaxation and cyclic tests are in reasonable agreement with the experimental observations.