Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
- 2016 (379) (entfernen)
Dokumenttyp
- Vortrag (379)
Referierte Publikation
- nein (379)
Schlagworte
- NDT (13)
- Korrosion (12)
- Reliability (12)
- Welding (11)
- Fluorescence (8)
- Microstructure (8)
- Tribology (8)
- Composite (7)
- Friction (7)
- Nichtrostende Stähle (7)
Eingeladener Vortrag
- nein (379) (entfernen)
Dieses Dokument fasst den Projekfortschritt des BAM-Projektes "Ermittlung geeigneter Wärmeführungen zur Wasserstoffreduktion
beim Schweißen höherfester Feinkornbaustähle mit modifiziertem
Sprühlichtbogen" im Rahmen des Fachausschusses 1 "Schweißmetallurgie & Werkstoffverhalten" des DVS e. V. zusammen.
Dieses Dokument fasst den Projekfortschritt des BAM-Projektes "Ermittlung geeigneter Wärmeführungen zur Wasserstoffreduktion beim Schweißen höherfester Feinkornbaustähle mit modifiziertem Sprühlichtbogen" im Rahmen des Fachausschusses 1 "Schweißmetallurgie & Werkstoffverhalten" des DVS e. V. zusammen.
Dark-field Transmission electron microscopy (DFTEM) results were obtained and presented. The results are discussed with regard to additional microstructural characterisation of the primyra Phase and creep experiments of alloy 2618A. Different methods to determine the volume fractions of precipitate phases are presented.
The LEK94 is a Ni-base superalloy single crystal (SX) of the second generation, a materials class which is important for its high temperature creep resistance (>1000°C) in first stage blades of low-to-medium pressure gas turbines. Monocrystalline Ni-base superalloy SXs have a two-phase microstructure consisting of small cubes (' phase with the ordered L12 crystal structure, cube edge length: 500 nm), separated by thin channels (γ phase with fcc solid solution structure, channel width: 20 nm). The microstructural evolution during high temperature and low stress tensile creep has been thoroughly investigated previously, mainly for [001] loading, both in terms of dislocation activity (filling of γ channels, formation of dislocation networks, cutting of the γ’ phase) as well as phase coarsening (rafting, topological inversion). Other loading geometries have received less attention.
The present work studies high temperature and low stress creep deformation of the superalloy LEK 94 at temperatures around 1000°C, where rafting occurs. Differences between loading under different uniaxial, biaxial and triaxial stress states are discussed. Stereo-microscopy and g∙b analysis in the scanning transmission electron microscopy mode (STEM) are combined for microstructural analysis. The focus is set on the role of dislocation interactions with the aging microstructure. Both development in STEM characterization methods, as well as the roles of phase coarsening, γ channel filling, microstructural heterogeneity and γ’ phase cutting are discussed.
Complex materials (e.g., porous ceramics) need high resolution techniques at multi-scale levels. Microstructure is intimately linked to properties and performance. One technique (or even a few techniques) is not enough. X-ray refraction and CT are very powerful tools. Non-destructive characterisation and quantitative image analysis techniques (2D and 3D) are necessary to understand the anisotropy.
Several restoration projects of stained-glass windows have been performed in Lower Silesia (Poland) since 2010. The aim of the projects was to protect stained-glass windows against environmental impact of industial pollutants and acid rain by installing a protective glazing. The usefulness of protective glazing has been proved by climate measurements and determination of environmental impact before and after installation.
Der Vortrag gibt einen Überblick die deutsche Ressortforschung. Neben einer Einordnung in das deutsche Wissenschaftssystem werden in einem historischen Überblick die Besonderheiten der Ressortforschung diskutiert. Besonderes Augenmerk wird der Frage gewidmet „Was ist gute Ressortforschung“. Kritisch erscheint besonders die Vereinbarkeit von exzellenter Wissenschaft und seriöser und unabhängiger Politikberatung.
The presentation shows how the three-dimensional quantification of dislocations and their characteristic features, e.g. Burgers vector, line direction, dislocation density, is carried out at the transmission electron microscope in scanning mode (STEM) at Division 5.1 at BAM. Exemplarily, the methods are shown for Ni-base superalloy single crystals, for which a short introduction is given using further TEM techniques. Additional examples on low angle grain boundaries, nucleation of oxides at dislocations and interaction of dislocations and carbides are shown.
The content of the presentation was addapted, aiming at scientists who work within the DFG Priority Programme 1713 "Strong coupling of thermo-chemical and thermo-mechanical states in applied materials".
In Germany the damages on concrete motorways have increased during the past 15 years. This led often to a reduction of service life from 30 to 10 years. In spite of comprehensive research the reasons for these damages have not been clarified yet. But it is known that in this context the ASR plays a decisive role. Against this background ASR performance tests have been developed. However, these tests do not take into account the effects of mechanical loading due to cyclic traffic and climatic impact. Therefore in Germany the ASR research group 1498 was founded. The research group consists of three experimentally- and two multi-scale modelling oriented subprojects, which are working closely together. Selected findings of BAM’s experimental subproject SP4 are content of this contribution. The aim was to investigate the impact of a cyclic mechanical pre-damage on moisture transport. The pre-damaging was carried out on large-format beams using a cyclic four point bending test with a total number of 5 million load cycles. Thereby the damage process was monitored by using different NDT-techniques. After the mechanical pre-damaging, smallsized specimens were taken from loaded as well as unloaded areas of the large format beams. Absorption tests were carried out on these specimens using water and NaCl solution. Thereby moisture distribution was measured with Nuclear Magnetic Resonance (NMR) and Time Domain Reflectometry (TDR). Additionally, moisture suction was quantified integrally by means of gravimetric measurements. The analysis of the first test data shows that the mechanical loading influences the moisture transport.
The concrete prism test at 60°C facilitates accelerated testing of alkali-silica reactivity of aggregates within five months. Manual measurement is usually conducted to determine expansion of test specimen every 28 days. This conventional procedure gives only limited insight to expansion behaviour of ASR-affected prisms. Due to the large time intervals, expansion exceeding the critical value of 0.3 mm/m is likely to be noticed late. Continuous recording applied in this work resolves this problem and delivers beneficial information on the shape of the expansion curve.
Different types of aggregate have been tested applying continuous and manual measurement to the concrete specimens.
Models of ASR-induced expansion, available in the open literature, so far are validated with discontinuous data hardly tracing the modelled curve. Continuous measurement improves validation and further model development.
The martensitic steels X30CrMoN15-1 and 100Cr6 did not show any hydrogen enhanced wear in sliding friction tests against alumina balls in hydrogen gas environment. However, depending on the purity of the environment, unexpected high wear occurred at the alumina ball. The results of a tests series with a broad variation of test parameters are presented.
The novel heat treatment concept, “quenching and partitioning” (Q&P) has been developed for high strength steels with enhanced formability. This heat treatment involves quenching of austenite to a temperature between martensite start and finish, to receive a several amount of retained austenite. During the subsequent annealing treatment, the so called partitioning, the retained austenite is stabilized due to carbon diffusion, which results in enhanced formability and strength regarding strain induced austenite to martensite transformation. In this study a Q&P heat treatment was applied to a Fe-0.45C-0.65Mn-0.34Si-13.95Cr stainless martensite. Thereby the initial quench end temperature and the partitioning time were varied to characterize their influence on microstructural evolution. The microstructural changes were analysed by dilatometer measurements, X-ray diffraction and scanning electron microscopy, including electron back-scatter diffraction. Compression testing was made to examine the mechanical behaviour. It was found that an increasing partitioning time up to 30 min leads to an enhanced formability without loss in strength due to a higher amount of stabilized retained and reversed austenite as well as precipitation hardening.
Härte, Schneidleistung und Korrosionsbeständigkeit sind die wichtigsten Qualitätsmerkmale von Schneidwaren, die nur durch eine optimal durchgeführte Wärmebehandlung des martensitischen nichtrostenden Stahls 1.4116 (X50CrMoV15) erreicht werden können. In der industriellen Fertigung wird die Korrosionsbeständigkeit von Schneidwaren durch Wechseltauchversuche überprüft, die herstellerübergreifend eine große Schwankung der Korrosionsbeständigkeit zeigen. In den letzten Jahren wurden neue elektrochemische Untersuchungsmethoden für die Werkstoffgruppe der martensitischen nichtrostenden Stähle entwickelt, welche die geringe Lochkorrosionsbeständigkeit von Schneidwaren auf das Phänomen der Chromverarmung zurückführen. Derzeit wird in der wissenschaftlichen und in der industriellen Gemeinschaft der Schritt des Anlassens als Ursache der Chromverarmung angesehen. Bei Schneidwaren sind die Anlasstemperaturen allerdings zu gering, um die auftretende Chromverarmung zu erklären. Aus diesem Grund wurde eine systematische Untersuchung der wichtigsten Wärmebehandlungsparameter: Härtetemperatur, Haltedauer, Abkühlrate und Anlasstemperatur durchgeführt, um den Einfluss aller Wärmebehandlungsparameter auf das Auftreten von Chromverarmung aufzuklären. Durch die elektrochemisch potentiodynamische Reaktivierung (EPR) erfolgte der Nachweis von Chromverarmung. Außerdem wurde die Lochkorrosionsanfälligkeit durch die anwendernahe KorroPad-Prüfung und die Bestimmung kritischen Lochkorrosionspotentiale ermittelt. Beides zeigt den Einfluss der durch die Wärmebehandlung erzeugten Chromverarmung auf die Lochkorrosionsbeständigkeit, die beim Einsatz und bei der Reinigung von Schneidwaren notwendig sind.
Die Korrosionsbeständigkeit martensitischer nichtrostender Stähle (MNS) wird wesentlich von der chemischen Zusammensetzung und dem Wärmebehandlungszustand beeinflusst. Beides bestimmt die Verteilung der Legierungselemente im Gefüge und die daraus resultierenden Werkstoffeigenschaften. Das Legieren mit Stickstoff bewirkt im Allgemeinen eine Verbesserung der Lochkorrosionsbeständigkeit von nichtrostenden Stählen. Bei martensitischen nichtrostenden Stählen ist dieser Effekt nicht nur auf den Stickstoffgehalt selbst zurückzuführen, sondern auch auf den gleichzeitig verringerten Kohlenstoffgehalt, der ebenfalls das Ergebnis der Wärmebehandlung beeinflusst. In dieser Arbeit wird der Einfluss von Stickstoff auf die Korrosionsbeständigkeit in Bezug zum Härtungsprozess von MNS dargestellt. Dazu wird vergleichend der Effekt von Austenitisierungsdauer, -temperatur und Abkühlgeschwindigkeit auf Gefüge, Härte und Korrosionsbeständigkeit der MNS X50CrMoV15 und X30CrMoN15 1 untersucht. Die Abkühlgeschwindigkeit wurde mit dem Stirnabschreckversuch gezielt variiert, um den Einfluss von Abkühlgeschwindigkeiten von > 100 K/s bis 1 K/s zu charakterisieren. Die Veränderungen der Korrosionsbeständigkeit werden durch die elektrochemisch potentiodynamische Reaktivierung (EPR) und durch die Bestimmung kritischer Lochkorrosionspotentiale dokumentiert. Neben diesem experimentellen Ansatz werden auch die Ergebnisse von thermodynamischen Berechnungen mit der Software Thermocalc vorgestellt und abschließend auch zur Interpretation des Einflusses von Stickstoff auf die Korrosionsbeständigkeit martensitischer nichtrostender Stähle genutzt.
The corrosion resistance of martensitic stainless steels (MSS) depends strongly on the chemical composition and the applied heat treatment. Both determine the distribution of the alloying elements in the microstructure and the resulting material properties. The addition of nitrogen is known to be beneficial for the pitting corrosion resistance of stainless steels. In case of MSS this effect is not only connected to nitro-gen itself because nitrogen can be used to substitute carbon which also influences the result of the heat treatment process. This paper shows the effect of nitrogen on the corrosion resistance in relation to the hardening process of MSS. Therefore the effects of austenitization temperature and cooling rate on microstructure, hardness and corrosion resistance were studied on the MSS X30CrMoN15 1 and X50CrMoV15. The effect of different cooling rates was studied using the jominy end quench test. The changes in corrosion resistance were detected with electrochemical potentiodynamic reactivation (EPR) and by the determination of critical pitting potentials. Besides this experimental approach thermodynamic calculations with the software thermocalc will be presented and used for the interpretation of the effect of nitrogen on the corrosion resistance of MSS.
Hydrogen can have an extreme degradation effects in steels, particularly concerning the mechanical properties. These effects can lead to hydrogen assisted cracking in micro-alloyed high strength steels during fabrication and/or operation in industrial applications. The Carrier Gas Hot Extraction method, which functionally combines a mass spectrometer with a Thermal Desorption Analysis process, was used for the detection of ultra-low diffusible hydrogen concentrations in the material specimens. The work shows the interaction between hydrogen and lattice defects in different micro-alloyed materials and HAZ. These steels were prepared in a quenched and tempered condition and in a thermo-mechanically rolled condition. The trapping characteristics of two steel grades, S690QL and S700MC, were studied with respect to the activation energy dependent on carbon content and micro-alloying elements such as Ti, Nb, Mo, Cr and V. The two steel grades exhibited several types of traps: carbide formations, dislocations and/or grain boundaries were common, which can influence activation energy and hydrogen solubility. The type and dimension of inclusions or particles also affected the hydrogen trapping behavior. A decrease of carbon and specific alloying elements in MC steels led to a change in the activation energy binding the trapped hydrogen. This thermo-mechanically hot
rolled steel revealed an increased interaction between hydrogen
and precipitations. The higher carbon content in the
quenched and tempered steel led to a higher interaction
between hydrogen and iron carbide, specifically in the
martensitic phase. Furthermore,the trapping behavior in HAZ showed a significant increase in activation energy, especially in the coarse grained microstructure.
Three high strength Nb-, Ti- and Ti+V- bearing S690QL steels were welded to investigate and compare the effects of microalloy addition on HAZ toughness. Charpy V notch impact tests from three microalloyed welds under different cooling rates have been performed. Fractographic examination shows that several factors including large-sized grain, upper bainite or hard second phase, interact to determine the brittle fracture mode and impaired toughness of Nb bearing weld at high heat input. In contrast to this reduced toughness, Ti bearing welds exhibits satisfied toughness regardless of at a fast or slow cooling rate as a result of limited austenite grain and refined favourable intragranular acicular ferrite structure. Moreover, in the case of such refined structure as matrix, TiN particles are found to be irrelevant to the fracture process and crystallographic misorientation results also confirms that high angle boundaries between fine ferrites plates provide much effective barrier for crack propagation and contribute to improved toughness.