Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
- 2019 (976) (entfernen)
Dokumenttyp
- Vortrag (443)
- Zeitschriftenartikel (257)
- Posterpräsentation (116)
- Beitrag zu einem Tagungsband (104)
- Sonstiges (19)
- Forschungsbericht (10)
- Buchkapitel (9)
- Dissertation (6)
- Monografie (3)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (3)
Sprache
- Englisch (731)
- Deutsch (235)
- Mehrsprachig (8)
- Russisch (1)
- Spanisch (1)
Schlagworte
- Additive Manufacturing (47)
- Corrosion (45)
- Korrosion (33)
- Additive manufacturing (29)
- Additive Fertigung (20)
- Microstructure (17)
- Nanoparticles (17)
- Fluorescence (16)
- Computed tomography (15)
- Mechanochemistry (14)
- Residual stress (14)
- Nanoparticle (13)
- Quantum yield (13)
- Boehmite (12)
- Glass (12)
- In situ (12)
- Laser implantation (12)
- Lifetime (12)
- MIC (12)
- Surface functionalization (12)
- Thermografie (12)
- Welding (12)
- 316L (11)
- Laser beam welding (11)
- TiB2 (11)
- Wasserstoff (11)
- Computed Tomography (10)
- Hydrogen (10)
- Laser-induced periodic surface structures (LIPSS) (10)
- Nano (10)
- Nanocomposites (10)
- Nichtrostender Stahl (10)
- SAXS (10)
- Simulation (10)
- Thermography (10)
- Diffraction (9)
- Dye (9)
- Eigenspannungen (9)
- Friction (9)
- Surface texturing (9)
- TED-GC-MS (9)
- Wear (9)
- 3D printing (8)
- Carbon steel (8)
- Deckschichtbildung (8)
- Degradation (8)
- Korrosionsschutz (8)
- Magnetocaloric (8)
- Material Science (8)
- Nanomaterial (8)
- Photoluminescence (8)
- Qualitätssicherung (8)
- Steel (8)
- Zerstörungsfreie Prüfung (8)
- AISI D2 (7)
- Ageing (7)
- Applications (7)
- Gelartige Elektrolyte (7)
- Hochfeste Feinkornbaustähle (7)
- Kaltrisse (7)
- Laser Metal Deposition (7)
- Mechanical properties (7)
- Methanogens (7)
- NIR (7)
- Neutron Diffraction (7)
- Numerical simulation (7)
- Polymer (7)
- Polymers (7)
- Quantum dot (7)
- Schweißen (7)
- Synthesis (7)
- 3D Druck (6)
- CCS (6)
- Ceramic (6)
- Duplex (6)
- Energy harvesting (6)
- Epoxy (6)
- Fatigue (6)
- Femtosecond laser (6)
- Femtosecond laser ablation (6)
- Gefahrgut (6)
- Gefahrstoff (6)
- Implant-Test (6)
- Ink (6)
- KorroPad (6)
- Lanthanide (6)
- Laserstrahlschweißen (6)
- Low Cycle Fatigue (6)
- MAG-Schweißen (6)
- Microplastics (6)
- Nanocomposite (6)
- Non-destructive testing (6)
- Normung (6)
- Oxidation (6)
- Pitting (6)
- Prüfmethode (6)
- Ringversuch (6)
- Sensor (6)
- Validierung (6)
- Water content (6)
- AIS (5)
- AKR (5)
- AM (5)
- Archaeometry (5)
- Atomic Force Microscopy (AFM) (5)
- CO2 (5)
- Calibration (5)
- Cement (5)
- Characterization (5)
- Coating (5)
- Crack growth (5)
- Creep-resistant steel (5)
- Crystallization (5)
- Cyclization (5)
- Electron microscopy (5)
- Explosionsschutz (5)
- Finite element method (5)
- Flow cytometry (5)
- Hybrid Laser Arc Welding (5)
- Inks (5)
- Korrosionsprüfung (5)
- Künstliche Bewitterung (5)
- Laser Powder Bed Fusion (5)
- MALDI-TOF MS (5)
- Mechanical strength (5)
- Method (5)
- Modeling (5)
- Multiplexing (5)
- NDT (5)
- Non-Destructive testing (5)
- Photophysics (5)
- Polyaniline (5)
- Polylactide (5)
- Pyrotechnik (5)
- Quality assurance (5)
- Quantum dots (5)
- Reference materials (5)
- Residual Stress (5)
- Rigid amorphous fraction (5)
- SLM (5)
- Sicherheitstechnische Kenngrößen (5)
- Solidification cracking (5)
- Standardisation (5)
- Surface (5)
- Synchrotron (5)
- Ti-6Al-4V (5)
- Wärmeführung (5)
- X-ray refraction (5)
- X38CrMoV5-3 (5)
- XRD (5)
- Zink (5)
- Adjustment calculation (4)
- Aluminium (4)
- Analytische Zentrifuge (4)
- Assay (4)
- Bead (4)
- Biodiesel (4)
- Broadband dielectric spectroscopy (4)
- Catalysis (4)
- Composite (4)
- Copper (4)
- Coptic (4)
- Crevice corrosion (4)
- Direct energy deposition (4)
- Durability (4)
- ECA (4)
- EPDM (4)
- Eddy Current (4)
- Encoding (4)
- Environment (4)
- GMR (4)
- Geothermal (4)
- HNBR (4)
- Highspeed-plasma-laser-cladding (4)
- Hybride Gemische (4)
- IR (4)
- Innenhydrophobierung (4)
- Keyhole mode welding (4)
- Klebfestigkeit (4)
- L-PBF (4)
- LBM (4)
- Laser-induced X-ray emission (4)
- Laser-induced periodic surface structures, LIPSS (4)
- MOF (4)
- Manuscripts (4)
- Martensite (4)
- Mechanism (4)
- Metals (4)
- Mikroplastik (4)
- Mikrostruktur (4)
- NMR (4)
- Neutron diffraction (4)
- Open data (4)
- Open science (4)
- Particle size distribution (4)
- Polymers of intrinsic microporosity (4)
- Porosity (4)
- Post weld heat treatment (4)
- Radiation protection (4)
- Raman Spectroscopy (4)
- Residual stresses (4)
- Schadensanalyse (4)
- Schleifen (4)
- Specific heat spectroscopy (4)
- Surface chemistry (4)
- Thin films (4)
- Traceability (4)
- Transmission electron microscopy (4)
- UHPC (4)
- Ultraschall (4)
- Ultrashort laser material interaction (4)
- X-Ray Imaging (4)
- X-Ray imaging (4)
- X-ray computed tomography (4)
- XPS (4)
- Zinküberzüge (4)
- AFM (3)
- ATR (3)
- Absorption edge tomography (3)
- Additive Manufacturing (AM) (3)
- Alloy 2618A (3)
- Analytik (3)
- Anerkennungen (3)
- Anisotropy (3)
- Archaea (3)
- Atmosphärische Korrosion (3)
- AuNP (3)
- Auslagerungsversuche (3)
- Ausnahmegenehmigungen (3)
- Austenitic stainless steels (3)
- Barcoding (3)
- Bending modulus (3)
- Bimetallkorrosion (3)
- Carbon capture (3)
- Carbon nanotubes (3)
- Catalyst (3)
- Ceramic spring (3)
- Ceramics (3)
- Chemical composition (3)
- Composites (3)
- Corrosion monitoring (3)
- Crosslinking (3)
- Cyclic R-curve (3)
- DCB (3)
- Damage detection (3)
- Deposition welding (3)
- Dielectric spectroscopy (3)
- Diesel (3)
- Digitalization (3)
- Diopside (3)
- Discotic Liquid Crystals (3)
- Dosimetry (3)
- EBSD (3)
- EPMA (3)
- Einstufung (3)
- Electromagnetic Weld Pool Support (3)
- Element transport (3)
- End crater (3)
- Energy transfer (3)
- Erstarrungsriss (3)
- Explosionsgrenzen (3)
- FAME (3)
- FKM (3)
- FTIR (3)
- Festlegungen (3)
- Flame retardant (3)
- Flash DSC (3)
- Freibewitterung (3)
- Full Penetration (3)
- Full-Notch Creep Test (FNCT) (3)
- Geant4 (3)
- Graphene (3)
- Guideline (3)
- Haftfestigkeit (3)
- Harmonisation (3)
- Heat conduction (3)
- High power laser beam welding (3)
- High temperature corrosion (3)
- High-strength steels (3)
- Hot-Stamping (3)
- Hybrid laser-arc welding (3)
- IgG (3)
- InP (3)
- Inconel 718 (3)
- Indium phosphide (3)
- Inter-laboratory comparison (3)
- Kunststoffe (3)
- LCF (3)
- LIBS TIG welding (3)
- LLG (3)
- LPA (3)
- Laminography (3)
- Large-scale test (3)
- Laser Powder Bed Fusion (L-PBF) (3)
- Laser Pulver Auftragsschweißen (3)
- Laser beam melting (3)
- Laser metal deposition (3)
- Laserimplantation (3)
- MCS (3)
- Magnetohydrodynamics (3)
- Materials (3)
- Materials Science (3)
- Materials science (3)
- Microdosimetry (3)
- Micromagnetism (3)
- Moisture clog (3)
- Monte-Carlo simulation (3)
- Mueller-Matrix imaging ellipsometry (3)
- Nanofibers (3)
- Nanomaterialien (3)
- Non-destructiv testing (3)
- OECD (3)
- OOMMF (3)
- Orientation (3)
- Passivität (3)
- Phase transformation (3)
- Plastic (3)
- Polycarbonate (3)
- Polymer blends (3)
- Polymere (3)
- Polyurethane (3)
- Pores (3)
- Process monitoring (3)
- Protein G (3)
- Prüfrichtlinie (3)
- Prüfverfahren (3)
- Reflectography (3)
- Research data management (3)
- Restraint (3)
- Rheology (3)
- Richtlinien (3)
- Rigidity (3)
- Roughness (3)
- Rubber (3)
- Röntgenrefraktion (3)
- SWIR (3)
- Sauerstoff (3)
- Scanning electron microscopy (3)
- Selective Laser Melting (3)
- Selective laser melting (3)
- Sicherheitstechnische Bewertung (3)
- Slurry (3)
- Small-angle scattering (3)
- Spectroscopic ellipsometry (3)
- Spectroscopy (3)
- Spectroskopic Imaging (3)
- Stress relief cracking (3)
- Structural health monitoring (3)
- Sulfidation (3)
- Superplasticizer (3)
- Synchrotron tomography (3)
- TEKKEN-Test (3)
- Temperature (3)
- Tensile properties (3)
- Testing (3)
- Thermoelectrics (3)
- Thick Materials (3)
- Tribology (3)
- Tunnel (3)
- Uncertainty (3)
- Upconversion nanoparticle (3)
- Utilization (3)
- Water speciation (3)
- Weld pool shape (3)
- X-ray diffraction (3)
- X-ray scattering (3)
- XRF (3)
- Zinc coatings (3)
- Zugeigenschaften (3)
- Zulassungen (3)
- µ-gravity (3)
- Überzüge (3)
- 1H-NMR (2)
- 3D (2)
- AISI 316L (2)
- AKR-Betonversuche (2)
- ALD-Hybridprozesse (2)
- ASR (2)
- Absolute fluorometry (2)
- Acoustic Emission (2)
- Acoustic levitation (2)
- Adhesive joint (2)
- Adhäsion (2)
- Adsorbed layer (2)
- Adsorption (2)
- Advanced Materials (2)
- Advanced high strength steel (2)
- Aerosol measurements (2)
- Al2O3-Schichten (2)
- Altern (2)
- Antibody coating (2)
- Antikörper (2)
- Arabic Recipes (2)
- Armaturenprüfung (2)
- Artificial weathering (2)
- Atomic Layer Deposition (2)
- Auftragschweißen (2)
- Ausgleichungsrechnung (2)
- BAMline (2)
- BDS (2)
- Baustoffe (2)
- Bauteilprüfung (2)
- Beständigkeit (2)
- Beständigkeitsbewertungen (2)
- Betonfahrbahn (2)
- Bioactive glass (2)
- Bioceramics (2)
- Biofilm (2)
- Biofilmbildung (2)
- Biosensor (2)
- Boundary element method (2)
- Brechungsindex (2)
- Brexit (2)
- Brittle fracture (2)
- Building Materials (2)
- Bulging effect (2)
- C3A (2)
- CAT-Technologie (2)
- CCU (2)
- CCUS (2)
- CFK (2)
- CFRP (2)
- CLP (2)
- CLP-Verordnung (2)
- CMAS (2)
- COD-AGE (2)
- CT (2)
- Capture (2)
- Carbon (2)
- Chaboche model (2)
- Chemikalienrecht (2)
- Chemisch instabile Gase (2)
- Cleavable probe (2)
- Coarsening (2)
- Compatibility (2)
- Compatibility evaluations (2)
- Composite-Druckgefäß (2)
- Compressive Cyclic loading (2)
- Condensate (2)
- Condensation (2)
- Contact resonance (2)
- Continuum mechanics (2)
- Copolymer (2)
- Corrosion Fatigue (2)
- Corrosion inhibition (2)
- Corrosion products (2)
- Corrosion rate (2)
- Corrosion testing (2)
- Crack Propagation (2)
- Crack propagation (2)
- Crevice (2)
- Crystal plasticity (2)
- Cultural heritage (2)
- Cytotoxicity (2)
- DED (2)
- DIN EN 16516 (2)
- DLO (2)
- DNA (2)
- DNA damage (2)
- Damage (2)
- Dangerous goods (2)
- Database (2)
- Deckschichten (2)
- Defokussierung (2)
- Dehnungsfehler (2)
- Delayed addition (2)
- Desiccation (2)
- Desinfection (2)
- Diffusion (2)
- Digital (2)
- Digital image correlation (2)
- Digital material representation (2)
- Digital twin (2)
- Dilatometry (2)
- Direct Energy Deposition (2)
- Direct Laser Metal Deposition (2)
- Distributed fibre optic sensing (2)
- Drinking (2)
- Druckbehältern (2)
- Dual phase steel (2)
- Duplexstahl (2)
- EOS (2)
- EPR (2)
- EU FP7 project NanoValid (2)
- Early hydration (2)
- Early oxidation (2)
- Elastic constants (2)
- Electron energy (2)
- Electron probe microanalysis (EPMA) (2)
- Electronic Detonators (2)
- Elektrochemie (2)
- Elemental composition (2)
- Ellipsometrie (2)
- Ellipsometry (2)
- End-crater (2)
- Endkrater (2)
- Energetic Materials (2)
- Energy deposit (2)
- Energy distribution (2)
- Environmental Simulation (2)
- Erdboden (2)
- Exchange interaction (2)
- Explosivstoffe (2)
- Extensometer (2)
- FT-IR (2)
- Faserverbund (2)
- Faserverbundwerkstoff (2)
- Fatigue crack growth (2)
- Fatigue crack propagation (2)
- FeCr- alloys (2)
- Ferromagnetism (2)
- Fiber reinforced polymer (2)
- Finite-Elemente-Methode (2)
- Formaldehyd (2)
- Fracture mechanics (2)
- Fracture surface analysis (2)
- Fragmentation (2)
- Fraktografie (2)
- Frequenzanalyse (2)
- Fräsen (2)
- Fume (2)
- Funtional Groups (2)
- GFK (2)
- GFRP (2)
- GHS (2)
- GTN model (2)
- Gas-Staub-Gemische (2)
- Gefährliche Stoffe (2)
- Gel-type electrolytes (2)
- Geothermal energy (2)
- Glass transition (2)
- Glass-ceramic (2)
- Gold (2)
- HAZPRED (2)
- HI-Tension (2)
- HPC (2)
- Haftvermittler (2)
- Harmonised Standards (2)
- Hazardous substances (2)
- Heat treatment (2)
- Heizöl (2)
- Heißriss (2)
- Herceptin (2)
- High Alloyed Steel (2)
- High Temperature Testing (2)
- High temperature (2)
- High-entropy alloys (2)
- High-performance concrete (2)
- High-pressure (2)
- High-strength concrete (2)
- High-strength steel (2)
- Hochfester Feinkornbaustahl (2)
- Hot cracking (2)
- Hot steam (2)
- Hybrid composite pressure vessel (2)
- Hydrogen assisted cracking (2)
- Hydrogen-assisted cracking (2)
- Hydrothermal treatment (2)
- Höherfester Feinkornbaustahl (2)
- IN 718 (2)
- Immunoassay (2)
- Immunocapture (2)
- Immunoglobulins (2)
- Immunoprecipitation (2)
- Immunosensor (2)
- Impurities (2)
- In situ Monitoring (2)
- In situ measurement (2)
- Innovation (2)
- Integrated analysis (2)
- Integrating sphere spectroscopy (2)
- Integrierte Analyse (2)
- Interlaboratory comparison (2)
- Internal friction (2)
- Interphase (2)
- Iridium-titanium mixed oxides (2)
- Iron (2)
- Irradiation (2)
- Kaltrissprüfung (2)
- Kavitation (2)
- Kennzeichnung (2)
- Keyhole mode laser beam welding (2)
- Kikuchi pattern (2)
- Kleb- und Haftfestigkeit (2)
- Kleinprobenprüfung (2)
- Kontinuumsmechanik (2)
- Korrosionsuntersuchungen (2)
- Kältemittel (2)
- LEE (2)
- LIMS (2)
- LMD (2)
- LME (2)
- LTT (2)
- Lamb waves (2)
- Landau Lifshitz equation (2)
- Laser (2)
- Laser Beam Melting (2)
- Laser Beam Welding (2)
- Laser cladding (2)
- Laser dispersing (2)
- Laserhybridschweißen (2)
- Laserschutz (2)
- Layer formation (2)
- Layerwise (2)
- Lean Duplex (2)
- Lebensdauerversuche (2)
- Localised corrosion (2)
- Lochkorrosion (2)
- Longitudinal Wave (2)
- Lubricants (2)
- MHD (2)
- MVT (2)
- Magnesium alloy (2)
- Magnetic moment (2)
- Magnetocaloric effect (2)
- Marktüberwachung (2)
- Mass spectrometry (2)
- Material degradation (2)
- Material science (2)
- Materialbearbeitung (2)
- Mehrprobenprüfung (2)
- Melting (2)
- Mesoporous thin films (2)
- Messunsicherheit (2)
- Metallene Werkstoffe (2)
- Metallic seal (2)
- Metallische Materialien (2)
- Metal–organic frameworks (2)
- Methane (2)
- Metrology (2)
- Microbiologically influenced corrosion (2)
- Microcracking (2)
- Microhardness (2)
- Mikroskaliert (2)
- Mixed Ca-K-Na phosphates (2)
- Modelling (2)
- Moisture transport (2)
- Molecular masses (2)
- Molten pool dynamics (2)
- Monte Carlo (2)
- Multi-layered system (2)
- Multiple cracks (2)
- Müller-Matrix-Ellipsometrie (2)
- NEXAFS (2)
- NMR spectroscopy (2)
- Na and K rhenanites (2)
- NanoSIMS (2)
- Nanocharacterisation (2)
- Nanomechanics (2)
- Nanoplastics (2)
- Nanoskaliert (2)
- Nanostructure (2)
- NiCrBSi (2)
- Nichtmetallische Materialien (2)
- Non destructive analytical techniques (2)
- Non destructive testing (2)
- Non-metallic inclusions (2)
- Nondestructive testing (2)
- Normen (2)
- OH radicals (2)
- Oberflächenenergie (2)
- Oberflächengeometrie (2)
- Object oriented micromagnetic framework (2)
- On-site mixed Explosives (2)
- Online Process Monitoring (2)
- Optical Tomography (2)
- Organic peroxides (2)
- Oriented immobilization (2)
- PEG (2)
- POD (2)
- Papyrus (2)
- Partial penetration (2)
- Particle gas emission (2)
- Particle size distributuion (2)
- Phase composition (2)
- Phase diagram (2)
- Phase transformations (2)
- Phononischer Kristall (2)
- Photon counting detector (2)
- Photoresist (2)
- Physikalische Gefahren (2)
- Pipeline (2)
- Pipeline steel X120 (2)
- Pipelines (2)
- Pitting corrosion (2)
- Plasma (2)
- Plasma-Transferred-Arc (2)
- Plume (2)
- Polyamide 12 (2)
- Polycarboxylate ether (PCE) (2)
- Polyethylene (2)
- Polyethylene glycol (2)
- Polyethylene, PE-HD (2)
- Polymer bilayer coatings (2)
- Polymer materials (2)
- Polymer matrix composites (2)
- Polymer nanocomposites (2)
- Powder (2)
- Powder Bed Fusion (2)
- Presshärten (2)
- Probe (2)
- Probengrößeneffekt (2)
- Process simulation (2)
- Protein A (2)
- Proximity-enhanced reaction (2)
- Prozesskette (2)
- Prüfmethoden (2)
- Pufferschichten (2)
- Pyrotechnics (2)
- QSPR (2)
- Quantitative Analysis (2)
- RSW (2)
- Radiationtherapy (2)
- Radioactive decay (2)
- Raman spectroscopy (2)
- Reheat cracking (2)
- Resistance spot welding (2)
- Resonance frequency (2)
- Rissbildung in Stahl (2)
- Round robin test (2)
- Rubber seal (2)
- Rundnaht (2)
- Röntgenbeugung (2)
- Röntgenemission (2)
- Scale-bridging (2)
- Scaled Boundary FEM (2)
- Schadenserkennung (2)
- Schallemission (2)
- Schallemissionsprüfung (2)
- Schallerzeuger (2)
- Schwingfestigkeit (2)
- Schädigung (2)
- Seal performance (2)
- Sekundärstrahlung (2)
- Selected Laser Melting (2)
- Self-reactive substances (2)
- Semiconductor nanocrystal (2)
- Sensibilisierung (2)
- Sensitization (2)
- Shore hardness (2)
- Silica beads (2)
- Silica nanoparticles (2)
- Silicon (2)
- Single particle spectroscopy (2)
- Sintering (2)
- Small angle scattering (2)
- Small-angle X-ray scattering (2)
- Soda-lime silicate glass (2)
- Soda-lime-silica glass (2)
- Software (2)
- Solidification (2)
- Spatter (2)
- Spectral sensitivity (2)
- Speed of sound (2)
- Stainless (2)
- Stainless Steel (2)
- Stainless steel (2)
- Standardization (2)
- Standards (2)
- Stochastic Landau Lifshitz Gilbert equation (2)
- Storage (2)
- Structural anomalies (2)
- Structural inhomogenities (2)
- Sulfate reducing bacteria (2)
- Superelliptic Lamé curves (2)
- Surface crystallization (2)
- Surface modification (2)
- Sustainability (2)
- Synthetic air (2)
- TMDSC (2)
- Tausalzeintrag (2)
- Technical Specification (2)
- Temeprature scaling (2)
- Temperature dependency (2)
- Temperature field (2)
- Temperaturschwankungen (2)
- Tensile Properties (2)
- Ternary quantum dots (2)
- Test method (2)
- Testing method (2)
- Thermal degradation (2)
- Thermal treatment (2)
- Thin polymer films (2)
- Thin polymeric films (2)
- Ti64 (2)
- TiAl5V4 (2)
- Titan (2)
- Titanium (2)
- Topografie (2)
- Tribofilm (2)
- Tribologie (2)
- Tungsten carbide (2)
- UN-GHS (2)
- UV degradation (2)
- Ultrakurze Laserpulse (2)
- Ultraschallunterstütztes Zerspanen (2)
- Ultrasonic Transducer (2)
- Ultrasonic testing (2)
- Upconversion (2)
- Upconversion nanoparticles (2)
- Utilization, and storage (CCUS) technology (2)
- VAMAS (2)
- VSSA (2)
- Validation (2)
- Variational calculus (2)
- Variationsrechnung (2)
- Verbundfestigkeit (2)
- Verifizierung (2)
- Virtual experiments (2)
- Water (2)
- Wear resistance (2)
- Weathering (2)
- Weld metal (2)
- Weld pool behavior (2)
- Weld pool shape approximation (2)
- Wellenprüfung (2)
- Werkstoffprüfung (2)
- Wind energy (2)
- Wirbelstromprüfung (2)
- X-ray CT (2)
- X-ray and electron diffraction (2)
- X-ray refraction techniques (2)
- X-ray-CT (2)
- Zero-g (2)
- Zerspanbarkeitsanalysen (2)
- Zinc coated steel (2)
- Zinkdeckschichten (2)
- Zirconia (2)
- Zonation (2)
- Zugversuch (2)
- Zuverlässigkeit (2)
- Zündenergie (2)
- Zündquellen (2)
- additive manufacturing (2)
- corrosion (2)
- fluorescence (2)
- low energy electrons (2)
- particle scattering (2)
- Überlappbereich (2)
- 16S rRNA gene (1)
- 18HLT01 MetVes II (1)
- 1D-Simulation (1)
- 2,6-diaminopyridine (1)
- 2D nanomaterials (1)
- 3D coherence scanning interferometry (CSI) (1)
- 3D imaging (1)
- 3D inspection (1)
- 3D-Printing (1)
- 3d structuring (1)
- 5G (1)
- 60 °C-Betonversuch (1)
- ABID (1)
- ACM (1)
- ADN Tabelle C (1)
- AEROSIL® OX50 (1)
- AET (1)
- AFM based test methods (1)
- AFM-IR (1)
- AFM-Kraft-Abstand-Kurven (1)
- AGIL (1)
- AIS QD (1)
- AISI 304L (1)
- AISI 321 stainless steel (1)
- AKR, Betonfahrbahndecke, Tausalzeintrag, Innenhydrophobierung (1)
- AM IN718 alloy (1)
- AXRD (1)
- Abrasion (1)
- Abrasive belt (1)
- Abtragende Glasbearbeitung (1)
- Accelerator (1)
- Acetone (1)
- Acoustic Emission (AE) (1)
- Acoustic emission (1)
- Acoustic emission analysis (1)
- Acoustic insulation (1)
- Acrylamide (1)
- Activation energy (1)
- Active Matter (1)
- Active thermography (1)
- Actuating materials (1)
- AdCo Explosives (1)
- Additiv (1)
- Additives (1)
- Admixture (1)
- Admixtures (1)
- Advanced high strength steels (1)
- Advanced materials (1)
- Affinity chromatography (1)
- Affinitätschromatographie (1)
- Affinitätsextraktion (1)
- Africa (1)
- Ageing behaviour (1)
- Ageing treatment (1)
- Aggressive environment (1)
- Aging tests (1)
- Aktive Thermographie (1)
- Akustischer Isolator (1)
- Al-Composite (1)
- Al-Cu-Li alloys (1)
- Al/SiO2 composite (1)
- Alcohols (1)
- Alite (1)
- Alkali-Kieselsäure Reaktion (1)
- Alkali-Kieselsäure-Reaktion (1)
- Alkali-activated materials (1)
- Alkali-silica reaction (1)
- Alkali-silica-reaction (1)
- Alkoxysilanes (1)
- Alpha (1)
- Alterung (1)
- Alumina (1)
- Aluminium-Druckguss (1)
- Aluminiumlegierungen (1)
- Aluminosilicate glasses (1)
- Aluminum alloy (1)
- Ameisensäure (1)
- Amplicon sequencing (1)
- Analysis (1)
- Anatase (1)
- Aneurism (1)
- Anisotropy estimate (1)
- Anoxia (1)
- Antibacterial (1)
- Antibodies (1)
- Antifouling surface coatings (1)
- Antifriction coefficient (1)
- Antimicrobial (1)
- Antiviral activity (1)
- Anwendungen (1)
- Approval (1)
- Aquifer (1)
- Arabic recipes (1)
- Arbitrary trajectories (1)
- Architecture (1)
- Arrhenius (1)
- Artungleiche Werkstoffe (1)
- Atemluftflasche (1)
- Atemschutz (1)
- Atomic force microscopy (1)
- Atomic fraction (1)
- Atomization (1)
- Aufbau von Festkörpern (1)
- Auftriebskräfte (1)
- Ausbildung (1)
- Auslaugung (1)
- Austenitic stainless steel (1)
- Autocorrelation (1)
- Automated expansion measurement (1)
- Automation (1)
- Automatische Dehnungsmessung (1)
- Automobilindustrie (1)
- BAM-Liste (1)
- BODIPY (1)
- BREXIT (1)
- BTS (1)
- Bacteria (1)
- Bacterial adhesion (1)
- Ball milling (1)
- Baumusterprüfungen (1)
- Bead-based assay (1)
- Beamline (1)
- Beanspruchungsanalyse (1)
- Beförderung gefährlicher Güter (1)
- Benannte Stellen (1)
- Bench braking sequence (1)
- Beschichtung (1)
- Bestimmung der Messunsicherheit (1)
- Beständigkeit in Biokraftstoffen (1)
- Beständigkeitsbewertung (1)
- Beta decay (1)
- Betriebsfestigkeit (1)
- Bewegtes Gitter (1)
- Bindemittel (1)
- Binnenwasserstraßen (1)
- Bio-based concrete (1)
- Biochip (1)
- Bioconjugation (1)
- Biofunctional Molecules (1)
- Biogene Brennstoffe (1)
- Biogeochemical cycling (1)
- Biomineralisation (1)
- Biopolymer (1)
- Biopolymers (1)
- Black Ink (1)
- Bloch wall (1)
- Blähen (1)
- Boehmite alumina (1)
- Boehmite nanoparticles (1)
- Bondline (1)
- Borosilikatglas (1)
- Brachytherapy (1)
- Braking load history (1)
- Brass (1)
- Breakdown strength (1)
- Brightness (1)
- Broadband dielectric microscopy (1)
- Bruchflächenanalyse (1)
- Bruchmechanik (1)
- Bubble formation (1)
- Build Angle (1)
- Bulge (1)
- Bulging (1)
- Bulk material (1)
- Bulk properties ageing (1)
- Bulk temperature (1)
- Bundesoberbehörden (1)
- Böden (1)
- Böhmit (1)
- C-C coupling (1)
- C. lap-shear (1)
- C3S (1)
- CAFTP (1)
- CALPHAD (1)
- CALPHAD databases analysis (1)
- CE-ICP-MS (1)
- CO2 Corrosion (1)
- CO2 separation membranes (1)
- CO2-Corrosion (1)
- CO2-Speicherung (1)
- CO2-storage (1)
- COK-12 (1)
- Cable (1)
- Calcination (1)
- Calcium cobaltite (1)
- Calcium peroxid (1)
- Calcium phosphate (1)
- Calculation time (1)
- Cancer (1)
- Cancer treatment (1)
- Carbide (1)
- Carbon Capture, Utilization and Storage (CCUS) (1)
- Carbon capture, utilization and storage technology (1)
- Carbon dioxide (1)
- Carbon dot (1)
- Carbon fibers (1)
- Carbon storage (1)
- Carrier gas hot extraction (1)
- Catalysts (1)
- Catch and release assay (1)
- Catechol (1)
- Cationic photocuring (1)
- Cavitation (1)
- Cell (1)
- Cell size (1)
- Cellulose (1)
- Cement admixtures (1)
- Cement hydration (1)
- Cement paste (1)
- Central Taurus (1)
- Centrifugal Adhesion Testing (1)
- Centrifugal Adhesion Testing (CAT) (1)
- Centrifugal Force (1)
- Certification Standard 22 (1)
- Certified reference materials (1)
- Certified standards (1)
- Characterisation (1)
- Chargenprüfung (1)
- Chemical admixtures (1)
- Chemical durability (1)
- Chemically Complex Alloy (1)
- Chemische Analyse (1)
- Chemo-mechanical coupling (1)
- Chloridbelastete Stahlbetonbauwerke (1)
- Chunky graphite (1)
- Circumferential weld (1)
- Circumferential welds (1)
- Civil Engineering (1)
- Classification (1)
- Cleavable linker (1)
- Click chemistry (1)
- Climate responsive materials (1)
- Cluster (1)
- Co (1)
- Co-axial monitoring (1)
- Co-crystal (1)
- CoO (1)
- Coal dust (1)
- Coarse-grained heat-affected zone (1)
- Cob (1)
- Cobalt (1)
- Cobalt and zinc oxides (1)
- Cocrystal (1)
- Codicology (1)
- Coefficient of thermal expansion (1)
- Coherent exchange (1)
- Cohesive Elements (1)
- Colored glasses (1)
- Combinatorial chemistry (1)
- Combinatorial polymer libraries (1)
- Community composition (1)
- Comparability of Measurement Results (1)
- Compatibility evaluation (1)
- Complex concentrated alloy (CCA) (1)
- Composite pressure vessel (1)
- Compression behavior (1)
- Compression set (1)
- Compression test (1)
- Compressive Stress (1)
- Computed tomography (CT) (1)
- Computer-Tomographie (1)
- Computertomographie (1)
- Concrete Prism Test at 60 °C (1)
- Concrete bridges (1)
- Concrete motorway pavements (1)
- Conductivity (1)
- Conductometry (1)
- Conference (1)
- Conjugates (1)
- Contact angle (1)
- Contact fatigue (1)
- Content of calcium peroxide (1)
- Controlled atmosphere (1)
- Convection coefficient (1)
- Copper-based wood preservatives (1)
- Coputed tomography (1)
- Cordierite (1)
- Core/shell quantum dot (1)
- Corrosion and storage (CCUS) technology (1)
- Corrosion pits (1)
- Corrosion product (1)
- Corrosion resistance (1)
- Coupled corrosive and mechanial load (1)
- Coupled corrosive/mechanical load (1)
- Crack (1)
- Crack arrest (1)
- Cracking (1)
- Creep (1)
- Cristobalite frameworks (1)
- Critical pitting temperature (1)
- Critical strain (1)
- Crosslinker (1)
- Crosslinking density (1)
- Cryogenic Engineering (1)
- Cryogenic Steel (1)
- Crystal Plasticity Modelling (1)
- Crystal Texture (1)
- Crystal orientation (1)
- Crystalline cones (1)
- Curie temperature (1)
- Curing (1)
- Curved surfaces (1)
- Cyclic (1)
- Cyclic J-integral (1)
- Cyclic R-curve analysis (1)
- Cyclic softening (1)
- Cycloaliphatic epoxy oligosiloxane (1)
- Cycloalyphatic epoxy oligosiloxane (1)
- D. aging (1)
- D. creep D. viscoelasticity (1)
- DED-L (1)
- DFG SPP 2005 (1)
- DIC assisted compression (1)
- DIN 50929-3 (1)
- DIN EN 717-1 (1)
- DIN EN ISO/IEC 17025:2018 (1)
- DMA (1)
- DPA (1)
- DRIFTS (1)
- Damage detection and localisation (1)
- Damage tolerant component design (1)
- Damping factor (1)
- Dangerous Goods (1)
- Dark-field transmission electron microscopy (DFTEM) (1)
- Data Processing (1)
- Data fusion (1)
- Data processing (1)
- Data storage (1)
- Dauerhaftigkeit (1)
- Dead Sea Scrolls (1)
- Dealloying (1)
- Declarations of conformity (1)
- Deep learning (1)
- Defect detection (1)
- Defect photoluminescence (1)
- Defects (1)
- Defekte Eigenspannung (1)
- Definition of nanomaterial (1)
- Deformation behavior (1)
- Denkmalpflege (1)
- Dense phase (1)
- Density Functional Theory (1)
- Destabilization (1)
- Deuterium (1)
- Diagnostic antibodies (1)
- Dichtmaterial (1)
- Dichtungswerkstoffe (1)
- Dielectric breakdown (1)
- Dielectric strength (1)
- Diesel Fuel (1)
- Digital Volume Correlation (1)
- Digitalisierung (1)
- Dipole moment (1)
- Directed Energy Deposition (1)
- Directed energy deposition (1)
- Dislocations (1)
- Dispersion of nano materials (1)
- Dissimilar metal weld overlays (1)
- Distortion (1)
- Distortion simulation (1)
- Distributed fiber optic sensing (1)
- Distributed fiber optic sensors (1)
- Distributed humidity sensor (1)
- Distributed sensor (1)
- Domain wall (1)
- Double complex salts (1)
- Drinking water (1)
- Drop test (1)
- Droplet (1)
- Droplet corrosion (1)
- Druckgasbehälter (1)
- Druckstabilität (1)
- Drug (1)
- Dual Energy Imaging (1)
- Dual energy (1)
- Dual sensing (1)
- Dual-Energy (1)
- Dual-energy (1)
- Ductile iron (1)
- Durability testing (1)
- Dye degradation (1)
- Dye labeling (1)
- Dynamic heterogeneity (1)
- Dynamic mechanical analysis (1)
- Dynamisch Mechanische Analyse (1)
- Dünne Schichten (1)
- E10 (Kraftstoff mit bis zu 10% Ethanol) (1)
- EASA (1)
- EC4SafeNano (1)
- EDX Analysis (1)
- EIS (1)
- ELISA (1)
- EMPIR (1)
- EMPIR project (1)
- ESI MS (1)
- Early sulfidation (1)
- Eddy current testing (1)
- Editorial (1)
- Editorial Board (1)
- Education (1)
- Eexisting structures (1)
- Efficient modelling (1)
- Eigenschaften (1)
- Eigenspannung (1)
- Einspanngrad (1)
- Einstufungskriterien (1)
- Elastic Constants (1)
- Elastin (1)
- Elastomerdichtung (1)
- Elastomere (1)
- Electrical conductivity (1)
- Electro-fused zirconia (1)
- Electro-thermomechnical model (1)
- Electrochemical characterisation (1)
- Electrochemical deposition (1)
- Electrochemical deposition (ECD) (1)
- Electrochemical impedance spectroscopy (1)
- Electrochemical potentiodynamic reactivation (1)
- Electrochemical sensing (1)
- Electrochemistry (1)
- Electrode geometry (1)
- Electromagnetic radiation (1)
- Electromagnetic scattering (1)
- Electromagnetic stirring (1)
- Electromagnetic weld pool support (1)
- Electromicroscopy (1)
- Electrospun fibers (1)
- Elektromagnetische Porenreduktion (1)
- Elektromagnetische Schmelzbadunterstützung (1)
- Elektromagnetsiche Schmelzbadbeeinflussung (1)
- Elektronische Zündesysteme (1)
- Elemenet transport (1)
- Elevated temperatures (1)
- Ellipsometric porosimetry (1)
- Emerging technologies (1)
- Emissionsprüfkammer (1)
- Emissionsprüfung (1)
- Enamels (1)
- Endurance Limit (1)
- Energiedissipation im Kontakt (1)
- Energy (1)
- Energy systems (1)
- Engine oil design (1)
- Engine oil testing (1)
- Engineering (1)
- Engineering applications (1)
- Environmental Stress Cracking (ESC) (1)
- Environmental simulation (1)
- Environmental stress cracking (1)
- Environmental stress cracking (ESC) (1)
- Environmentally assisted cracking (1)
- Epoxy conversion degree (1)
- Epoxy-Anhydrid Duroplast (1)
- Equivalent heat source (1)
- Ermüdung (1)
- Europium (1)
- Europäisches Übereinkommen (1)
- Evolution of bulk properties (1)
- Exchange length (1)
- Excitation power density (1)
- Experimental design (1)
- Explosion limits (1)
- Explosion protection (1)
- Explosionsartiges Abplatzen (1)
- Explosionsgefährliche Eigenschaften (1)
- Explosive spalling (1)
- Explosivplattieren (1)
- Explosivstoofe (1)
- Exposed metal sites (1)
- Extracellualr vesicles (1)
- Extracellular matrix (1)
- Extracellular vesicles (EV) (1)
- FIB/SEM (1)
- FLIM (1)
- FPLC (1)
- FRET (1)
- FSDC (1)
- FTIR spectroscopy (1)
- Fabrication (1)
- Facades (1)
- Facilitated activation (1)
- Fahrbahndeckenbetone (1)
- Failure test (1)
- Faser-Kunststoff-Verbunde (1)
- Faserkunststoffverbunde (1)
- Fast scanning calorimeter (1)
- Fast scanning calorimetry (1)
- Fast scanning calormetry (1)
- Fatigue Crack Propagation (1)
- Fatigue Life Evaluation (1)
- Fatigue S-N curve (1)
- Fatigue Testing (1)
- Fatigue crack propagation stages (1)
- Fatigue strength (1)
- Fatigue strength and life (1)
- Fatigue tests (1)
- Fe (1)
- Fe-Ni (1)
- Fe2TiO5 (1)
- Feinkornbaustahl (1)
- Ferritic spheroidal graphite cast iron (1)
- Ferritic steels (1)
- Ferritic–martensitic steel (1)
- Ferumoxytol (1)
- Festphasenextraktion (1)
- Feuerwehr (1)
- Fiber Bragg grating (FBG) (1)
- Fibres (1)
- Filtered back projection (1)
- Filters (1)
- Fine Powder (1)
- Fine-grained Steel (1)
- Fingerprint (1)
- Finite element analysis (1)
- Finite elements (1)
- Finite-element method (1)
- Fire (1)
- Fire damp (1)
- Flammability (1)
- Flammable Gas (1)
- Flammable Liquid (1)
- Flow Chemistry (1)
- Flow-system (1)
- Flowability (1)
- Fluid-flow (1)
- Fluorescence standard (1)
- Fluorescent label (1)
- Flüssigkeitssensor (1)
- Foaming (1)
- Focused Ion Beam (1)
- Force distance curve (1)
- Force distance curves (1)
- Force-distance diagram (1)
- Formation (1)
- Forschungsdatenmanagement (1)
- Forschungsstrategie (1)
- Four-point bending test (1)
- Fractography (1)
- Freeze Drying (1)
- Freeze casting (1)
- Fresnoit (1)
- Friction Stir Welding (1)
- Frozen state photopolymerization (1)
- Full penetration (1)
- Fully aromatic frameworks (1)
- Functionalization (1)
- Functionalized graphene (1)
- Functionalized nanographene (1)
- Fusion zone (1)
- Fügetechnologie (1)
- GMA welding (1)
- GMAW (1)
- GUM-compliance (1)
- Gadolinium (1)
- Gallium doping (1)
- Gamma (1)
- Gas Barrier Properties (1)
- Gas analytic (1)
- Gas permeability (1)
- Gas separation membranes (1)
- Geant4-DNA (1)
- Gefahrenklasse (1)
- Gefahrgruppen (1)
- Gefahrgutregeln (1)
- Gefahrstoffverordnung (1)
- Gefügeuntersuchung (1)
- Gelartige Elektolyte (1)
- Gelelektrolyte (1)
- Geology (1)
- Gesteinskorrosion (1)
- Ggraphene polymer nanocomposite (1)
- Glas (1)
- Glasmonolith (1)
- Glass ceramic (1)
- Glass paints (1)
- Glass powder (1)
- Glass scanning (1)
- Glass screening device (1)
- Gleichgewicht (1)
- Glucose (1)
- Glue (1)
- Gold Nanoparticle (1)
- Gold Nanoparticles (1)
- Gold nanoclusters (1)
- Grain boundary (1)
- Grain size (1)
- Grain structure (1)
- Graphene Oxide (1)
- Graphene polymer nanocomposite (1)
- Graphite modules (1)
- Grating (1)
- Grenzfläche als Material (1)
- Grinding (1)
- Grünfolieneigenschaften (1)
- HAZ (1)
- HDPE Soprption (1)
- HDPE Sorption (1)
- HPLC (1)
- HSLA (1)
- HVO (1)
- Halophile (1)
- Hamonisierung (1)
- Hard machining (1)
- Hardmetal (1)
- Hardness (1)
- Heat control (1)
- Heat saturation function (1)
- Heated concrete (1)
- Heating oil (1)
- Heating oil - biodiesel - blend (1)
- Heating oil tanks (1)
- Heating oil with 10 % FAME (1)
- Heating oil with 10% biodiesel (1)
- Heating oil with 20% biodiesel (1)
- Heating oil-Biodiesel-Blend (1)
- Heavy metal free (1)
- Heissrisse (1)
- Heizöl mit 10% Biodiesel (1)
- Heizöl mit 20 % Biodiesel (1)
- Heizöl mit 20% Biodiesel (B20) (1)
- Heizöl-FAME-Blends (1)
- Heißgaskorrosion (1)
- Heißrisse (1)
- Hierarchical porosities (1)
- High Molecular Polyethylene (1)
- High alloyed steel (1)
- High entropy alloys (1)
- High pressure (1)
- High specific surface area (1)
- High-power laser beam (1)
- High-temperature corrosion (1)
- High-temperature oxidation (1)
- High-voltage testing (1)
- Highspeed plasma (1)
- Hochentropielegierungen (1)
- Hochleistungslaserstrahlschweißen (1)
- Hot Cracking (1)
- Hot crack (1)
- Hot stamping (1)
- Human antibodies (1)
- Human umbilical cell adhesion (1)
- Hybrid components (1)
- Hybrid laser arc welding (1)
- Hybrider Werkstoffverbunde (1)
- Hydration (1)
- Hydrogel (1)
- Hydrogen Assisted Cracking (HAC) (1)
- Hydrogen Embrittlement (1)
- Hydrogen assisted stress corrosion cracking (1)
- Hydrogen dependent mechanical properties (1)
- Hydrogen diffusivity (1)
- Hydrogen methane (1)
- Hydrogen-containing hot gas (1)
- Hydrophobic interaction (1)
- Hydrophobin (1)
- Hydrothermal synthesis (1)
- Hydrothermale Calcinierung (1)
- Hygrothermal (1)
- Hyperbranched (1)
- Hysteresis measurement (1)
- Härte (1)
- IAEA fire (1)
- ICP-MS (1)
- IEQ (1)
- IIT (1)
- IR spectroscopy (1)
- ISO (1)
- ISO 14577 (1)
- ITS region (1)
- ImAFM (1)
- Imaging (1)
- Immobilisierung (1)
- Immobilization (1)
- Immunglobulin (1)
- Immunoaffinity extraction (1)
- Impact behaviour (1)
- Impact damage (1)
- Impedance spectroscopy (1)
- Implant test (1)
- Implant-test (1)
- Implants (1)
- Impurity segregation (1)
- In situ measurement, (1)
- In situ testing (1)
- In-Situ X-ray CT (1)
- In-situ Process Monitoring (1)
- Inclusion cluster (1)
- Inclusion size (1)
- Inconel 625 (1)
- Inconel 686 (1)
- Incremental lifetime models (1)
- Indenter modulus (1)
- Indonesien (1)
- Inertisierung (1)
- Inflammation (1)
- Infrared Thermography (1)
- Infrared nano AFM (1)
- Infrared spectroscopy (1)
- Infrared thermography (1)
- Initial crack size (1)
- Ink terminology (1)
- Inline NMR Spectroscopy (1)
- Innenraumluft (1)
- Insitu test (1)
- Institut Laue Langevin (1)
- Instrumented Indentation Testing (1)
- Instrumentierte Eindringprüfung (1)
- Instrumentierte Eindringprüfung (IIT) (1)
- Integrated Processes (1)
- Integrating sphere spectroscopy, (1)
- Inter-laborator comparison (1)
- Interdisciplinary (1)
- Interfaces (1)
- Interfacial forces (1)
- Intergranular cracking (1)
- Intermodulation (1)
- Intermodulation AFM (1)
- Intermodulation-AFM (1)
- Internal Surfaces (1)
- Internal oxidation (1)
- Introduction (1)
- Inverse Problems (1)
- Ionic porosity (1)
- Ions (1)
- Iron isotope fractionation (1)
- Iron meteorite (1)
- Iron oxide (1)
- Journal (1)
- Kabeltrenner (1)
- Kathodische Korrosionsschutz (1)
- Keramische Folien (1)
- Kieselsol (1)
- Kinetics (1)
- Klebeverbindungen (1)
- Knoevenagel condensation (1)
- Knotenweise Zwangsbedingungen (1)
- Kobaltlegierung (1)
- Kompaktierbarkeit (1)
- Kompressibilität (1)
- Konformitätsbewertung (1)
- Konformitätserklärung (1)
- Kontaktkorrosion (1)
- Korosi (1)
- Korrelationsmatrix (1)
- Korrosionsbeständigkeit (1)
- Korrosionsschnelltest (1)
- Korrosionsschäden (1)
- Korrosionsüberwachung (1)
- Korund (1)
- Kraftstoffabbau (1)
- Kraftstoffbehälter (1)
- Kreislaufwirtschaft (1)
- Kriechen (1)
- Kriechverhalten (1)
- Kristallisation (1)
- Kristallsystem (1)
- Kunststoff (1)
- Kunststoff und Röntgen-Rückstreuung (1)
- Kurz- und Langriss-Ermüdungsbruchmechanik (1)
- Kurzfaser-verstärkte Thermoplaste (1)
- Kurzrisswachstum (1)
- LC / MALDI-TOF-MS coupling (1)
- LC x ESI-TOF-MS (1)
- LC-MS (1)
- LCC (1)
- LCCC (1)
- LEVASIL 50/50 (1)
- LIBS (1)
- LL equation (1)
- LPBF (1)
- LT-FCM (1)
- LTCC multilayer (1)
- LTT filler material (1)
- LTT-Zusatzwerkstoff (1)
- La(Fe,Si)13 phase (1)
- Labelling (1)
- Lack-of-fusion (1)
- Lactide (1)
- Ladetankausrüstung (1)
- Laminates (1)
- Laminographie (1)
- Landau Lifshitz Gilbert equation (1)
- Large-pore (1)
- Laser Metal Deposition (LMD) (1)
- Laser Powder Bed Melting (1)
- Laser Scanning Microscopy (LSM) (1)
- Laser hybrid welding (1)
- Laser powder bed fusion (1)
- Laser processing (1)
- Laser surface texturing (1)
- Laser welding (1)
- Laser-Hybridschweißen (1)
- Laser-Pulver-Auftragschweißen (1)
- Laser-induced nanostructures (1)
- Laser-induced slip casting (1)
- Laser-modified surface (1)
- Laserauftragschweißen (1)
- Laserbearbeitung (1)
- Laserdispergieren (1)
- Laserpulverauftragschweißen (1)
- Laserscanningmikroskopie (LSM) (1)
- Laserstrahlhybridschweißen (1)
- Laserstrahlschmelzen im Pulverbett (1)
- Lattice structure (1)
- Layer system (1)
- Layer-by-layer deposition (1)
- Layerwise Slurry Deposition (1)
- Layerwise slurry deposition (1)
- Leaching of alkalis (1)
- Lead isotope composition (1)
- Lead-free (1)
- Leak-tightness (1)
- Lean duplex (1)
- Leather (1)
- Lebensdauer (1)
- Legierung (1)
- Legionella (1)
- Leichtbau (1)
- Levitation (1)
- Ligand (1)
- Linear polyglycerol (1)
- Liquid Crystals (1)
- Liquid crystals (1)
- Liquid metal embrittlement (1)
- Load history (1)
- Load partition (1)
- Local fatigue spproaches (1)
- Localized Laser Dispersing (1)
- Long-term storage (1)
- Low Reynolds number swimmers (1)
- Low Temperature Toughness (1)
- Low Transformation Temperature (1)
- Low cycle fatigue (1)
- Low heat input GMA welding (1)
- Low melting glasses (1)
- Low-tech approach (1)
- Lubrication (1)
- Luminescence (1)
- MAG (1)
- MALDI TOF MS (1)
- MALDI-TOF (1)
- MEMUS (1)
- MOF-74 (1)
- MPI (1)
- MPLS (1)
- Machine Learning (1)
- Macrophage (1)
- Magmatic and hydrothermal processes (1)
- Magnet coupling (1)
- Magnetic (1)
- Magnetic Nanoparticles (1)
- Magnetic anisotropy (1)
- Magnetic domains (1)
- Magnetic field (1)
- Magnetic interacion (1)
- Magnetic nanoparticle (1)
- Magnetic nanoparticles (1)
- Magnetic resonance imaging (1)
- Magnetic swimmers (1)
- Magnetische Domänen (1)
- Magnetization dynamics (1)
- Magnetocoloric (1)
- Magnetoelastic effect (1)
- Magnetoelastischer Effekt (1)
- Magnéli phase (1)
- Maintenance (1)
- Manual of Tests and Criteria (1)
- Market surveillance (1)
- Maskinteknik (1)
- Mass spectrometry of polymers (1)
- Mass transport (1)
- Massenspektrometrie (1)
- Masterbatch (1)
- Material characterization (1)
- Material defects (1)
- Materialien (1)
- Materialkreislauf (1)
- Materialprüfung (1)
- Measurement (1)
- Measurement uncertainty (1)
- Mechanical Engineering (1)
- Mechanical Properties (1)
- Mechanical behavior (1)
- Mechanical property (1)
- Medical implants (1)
- Medieval glasses (1)
- Mehr-Proben-Prüfverfahren (1)
- Mehrachsige Verformung (1)
- Melt pool behaviour (1)
- Melt-extraction technique (1)
- Mesoporous Silica (1)
- Mesoporous iridium-titanium mixed oxides (1)
- Mesoporous mixed metal oxide films (1)
- Messing (1)
- Messtechnik (1)
- Metal Matrix Composite (1)
- Metal carbides (1)
- Metal matrix composite (1)
- Metal organic framework (1)
- Metal phosphonates (1)
- Metal powder characterization (1)
- Metal reducing bacteria (1)
- Metal-organic-frameworks (1)
- Metalldichtung (1)
- Metallkorrosion (1)
- Metalls (1)
- Metallurgie (1)
- Methanogen (1)
- Method comparison (1)
- Method validation (1)
- Methos comparision (1)
- Micro-shrinkages (1)
- Microanalysis (1)
- Microarray (1)
- Microbeam analysis (1)
- Microbial (1)
- Microbially induced corrosion (1)
- Microbiologically Influrenced Corrosion (MIC) (1)
- Microencapsulation (1)
- Microparticle (1)
- Microparticles (1)
- Microplastic (1)
- Microstructural analysis (1)
- Microstructure Characterization (1)
- Microstructure analysis (1)
- Microstructure characterisation (1)
- Microstructure evolution (1)
- Microwave synthesis (1)
- Mikrostrukturuntersuchung (1)
- Milling (1)
- Mis-match (1)
- Mittelrippendefekt (1)
- Mixed-linkers (1)
- Modell der konstanten Flammentemperaturen (1)
- Modified Varestraint-/Transvarestraint test (1)
- Modular Production (1)
- Module (1)
- Moisture (1)
- Molecular mobility (1)
- Monitoring (1)
- Monte-Carlo (1)
- Mortar (1)
- Mortel (1)
- Moving mesh (1)
- Mueller-Matrix Ellipsometry (1)
- Multiaxial deformation (1)
- Multiphoton laser structuring (1)
- Multiple-layered scaffold (1)
- Multivariate data analysis (1)
- Museum insect pest (1)
- Mussel-inspired adhesives (1)
- NBR (1)
- NDT Monitoring (1)
- NIR dyes (1)
- NP (1)
- Nahtgeometrie (1)
- Nano particle (1)
- Nano screening (1)
- NanoValid (1)
- Nanocasting (1)
- Nanoconfinement (1)
- Nanocrystal (1)
- Nanohybrid (1)
- Nanoindentation (1)
- Nanokomposit (1)
- Nanomaterial Properties (1)
- Nanomechanical properties (1)
- Nanometrology (1)
- Nanoparticle Characterization (1)
- Nanoparticle characterization (1)
- Nanoparticle size measurement (1)
- Nanoparticular TiO2 (Anatase) (1)
- Nanoporous (1)
- Nanorods (1)
- Nanoscale (1)
- Nanosecond laser (1)
- Nanosecond laser irradiation (1)
- Nanostructure quantification (1)
- Nanotechnologie (1)
- Natural (1)
- NbC (1)
- Nd excitation (1)
- Neel wall (1)
- Neuartige Materialien (1)
- Neutron imaging (1)
- Neutronen Abschirmmaterial (1)
- Neutronenbeugung (1)
- Neutronenradiographie (1)
- Neutronentomographie (1)
- New standards (1)
- Next Generation Sequencing (1)
- Ni (1)
- Ni-Resist (1)
- Nicht-lineare Regression (1)
- Nickel (1)
- Nickel alloys (1)
- Nickellegierung (1)
- Niedrigenergie-Polymeren (1)
- Niobium alloying (1)
- Nitrene[2+1]cycloaddition (1)
- Nitride (1)
- Nitrides (1)
- Nitrieren (1)
- Nitrogen (1)
- Non-destructive Materials (1)
- Non-destructuve testing (1)
- Non-spherical shape (1)
- Nonclassical crystallization (1)
- Nosema ceranae (1)
- Notified bodies (1)
- Numerical Simulation (1)
- Numerical analysis (1)
- Numerical modelling (1)
- Numerische ISmulation (1)
- Numerische Simulation (1)
- OTDR (1)
- Oberfläche (1)
- Oberflächenanalytik (1)
- Oberflächenmesstechnik (1)
- Oberflächenpotential (1)
- Oberflächensteifigkeit (1)
- Oberflächentechnik (1)
- Oil and gas industry (1)
- Ooxidation (1)
- Optical Emission Spectroscopy (1)
- Optical assay (1)
- Optical criterion (1)
- Optical emission spectroscopy (1)
- Optical fiber sensor (1)
- Optical fibers (1)
- Optical measurment technique (1)
- Optical near field (1)
- Optical properties (1)
- Optical spectroscopy (1)
- Optical tomography (1)
- Optische Fasern (1)
- Optische Tomografie (1)
- Ordered mesoporous silica (1)
- Ore provenance (1)
- Organic–inorganic nanostructures (1)
- Orientation relationship (1)
- Oscillating magnetic field (1)
- Osmia bicornis (1)
- Outokumpu: Stainless steel (1)
- Oxidation protection (1)
- Oxocobaltates (1)
- Oxygen Evolution Catalyst (1)
- Oxygen evolution reaction (1)
- Oxygen evolution reaction (OER) (1)
- Oxygen permability (1)
- Oxygen reduction reaction (1)
- Oxygen sensitive (1)
- P25 (1)
- P92 (1)
- PC characterisation (1)
- PDT (1)
- PE-HD Sorption (1)
- PEAK (1)
- PH (1)
- PMMA (1)
- PTFE (1)
- PUR (1)
- Package (1)
- Package testing (1)
- Paint (1)
- Pair Distribution Functions (1)
- Papierasche (1)
- Parabolic flight (1)
- Paramagnetism (1)
- Parchment (1)
- Partial penetration laser hybrid welding (1)
- Particle (1)
- Particle accretion (1)
- Particle size (1)
- Partikelgrößenverteilung (1)
- Passivschicht (1)
- Path planning (1)
- Pathogen spillover (1)
- Pentaerythritol (1)
- Peptide (1)
- Peptide Library (1)
- Peptide mass fingerprinting (1)
- Peptides (1)
- Performance assessment (1)
- Performance test (1)
- Performance validation (1)
- Periodic inspections (1)
- Peritectic reaction (1)
- Permeability (1)
- Permitted explosives (1)
- Perovskite (1)
- Phage Display (1)
- Phase mask (1)
- Phase transition (1)
- Phase-field (1)
- Phase-field simulation (1)
- Phasenumwandlung (1)
- Phononic crystal (1)
- Phononische Kristalle (1)
- Phosphate (1)
- Phosphinine (1)
- Phosphonates (1)
- Phosphorus (1)
- Photocatalyst (1)
- Photocuring (1)
- Photogrammetry (1)
- Photoluminescence quantum yield (1)
- Photon Counting Detectors (1)
- Photon counting detectors (1)
- Photonenzählende Detektoren (1)
- Photooxidation (1)
- Photostability (1)
- Plasmon resonance (1)
- Plasmonic nanofocusing spectroscopy (1)
- Plastic deformation (1)
- Plastikstrategie (1)
- Platinum-group-metals (1)
- Polarisation (1)
- Polarization spectroscopy (1)
- Poly(N-vinylpyrrolidone) (1)
- Poly(vinyl chloride) (1)
- Polyamid 12 (1)
- Polycaprolactone (1)
- Polyethylen hoher Dichte (1)
- Polyethylene Glycol (1)
- Polymer Testing (1)
- Polymer aging (1)
- Polymer composites (1)
- Polymer optical fiber (1)
- Polymer particle (1)
- Polymer-based nanocomposites (1)
- Polymere Werkstoffe (1)
- Polymeric materials (1)
- Polymeric membrane (1)
- Polyphosphoester (1)
- Polypropylene (1)
- Polysaccharides (1)
- Pore size tailoring (1)
- Pore solution (1)
- Porosität (1)
- Porous ceramics (1)
- Porphyrin (1)
- Portland cement (1)
- Post-modification by L-cysteine (1)
- Potential (1)
- Potentiometry (1)
- Powder analysis (1)
- Practical aspects (1)
- Pre-standardisation (1)
- Preceramic polymer (1)
- Precipitation hardening (1)
- Precision polymer sequencing (1)
- Prediction (1)
- Pressure-assisted sintering (1)
- Pressverbindung (1)
- Prevention (1)
- Priam's treasure (1)
- Primär- und Sekundärspannungen (1)
- Process Analytical Technology (1)
- Process Monitoring (1)
- Process development (1)
- Process parameters (1)
- Processing window (1)
- Projection matrix (1)
- Projektmanagement (1)
- Propagation modes (1)
- Propane gas fire test facility (1)
- Properties (1)
- Protection (1)
- Protein (1)
- Proton cunductor (1)
- Prozessmanagement (1)
- Prozessmonitoring (1)
- Prozesssimulation (1)
- Prozessüberwachung (1)
- Prüftechnik (1)
- Pseudo peptides (1)
- Pulsed thermography (1)
- Pultruded fiber rods (1)
- Quality assurcance (1)
- Qualitätsmanagement (1)
- Quantum yields (1)
- Quinones (1)
- REACH (1)
- REM (1)
- RME (1)
- ROPPOC (1)
- RRT (1)
- Radiation damage (1)
- Radioactive NP (1)
- Radioactive material (1)
- Radioactive sources (1)
- Radiographie (1)
- Radiography (1)
- Radiological inspections (1)
- Raman microscopy (1)
- Rayleigh scattering (1)
- Reaction Monitoring (1)
- Real-time infrared spectroscopy (1)
- Reconstructed ion chromatograms (1)
- Recycling (1)
- Recycling-by-design (1)
- Reference Nanomaterials (1)
- Reference material (1)
- Reference methods (1)
- Reference particles (1)
- Referenzmaterial (1)
- Referenzorganismus (1)
- Referenzverfahren (1)
- Refraction (1)
- Regeneration (1)
- Regulation (1)
- Reinforcement (1)
- Relaxation fatigue (1)
- Repair patch (1)
- Representative material properties (1)
- Repräsentative Werkstoffeigenschaften (1)
- Residual Stresses (1)
- Residual stress analysis (1)
- Residual stressMultiphase compositesInteractionMicromechanical schemesAnisotropy (1)
- Resonance (1)
- Resonance testing (1)
- Restlebensdauer (1)
- Restoration and conservation (1)
- Reverse microemulsion (1)
- Rh-Ir alloys (1)
- Rheological properties (1)
- Rietveld (1)
- Ring-expansion polymerization (1)
- Ring-opening polymerization (1)
- Rissarrest (1)
- Risstrajektorie (1)
- Rod structure (1)
- Rohrprobekörper (1)
- Rosin (1)
- Rotorblatt (1)
- Round robin tests (1)
- Round-Robin-Tests (1)
- Rundnähte (1)
- Rührreibschweißen (1)
- SBFEM (1)
- SDC (1)
- SEC (1)
- SEM (1)
- SEM/EDS/STRATAGem (1)
- SIMS (1)
- SKPM (1)
- SRB (1)
- STEM (1)
- SWIR photoluminescence (1)
- Safety (1)
- Safety characteristics (1)
- Sailplane Development Panel (1)
- Salicylate (1)
- Salt melt (1)
- Samarium doped ceria (1)
- Sample preparation (1)
- Saure Hydrolyse (1)
- Scaffolds (1)
- Scaled Boundary Finite Element Method (1)
- Scanning Electron Microscopy (SEM) (1)
- Scanning electrochemical microscope (SECM) (1)
- Scanning transmission electron microscopy (1)
- Scattering (1)
- Scavenging effect of iron (1)
- Schadenstolerante Bauteilauslegung (1)
- Schallemmission (1)
- Schmiedeteile (1)
- Schmiermittel (1)
- Schwarzpulverähnliches Reinigungspulver (1)
- Schweißeigenspannungen (1)
- Schweißeigenspannungs-Tiefen-Profile (1)
- Schweißen von kaltzähen Stählen (1)
- Schweißstruktursimulation (1)
- Schädigungsverhalten (1)
- Science (1)
- Sciences (1)
- Scratches (1)
- Screening (1)
- Seal failure (1)
- Security (1)
- Segmentation (1)
- Selective Laser Melting (SLM) (1)
- Selective Laser Sintering (SLS) (1)
- Selektives Lasersintern (1)
- Self-assembly (1)
- Self-lubricating coating (1)
- Semi-metallic friction material (1)
- Semi-metallic sintered material (1)
- Semiconductor (1)
- Semiconductor materials (1)
- Sensitisation (1)
- Sensoren (1)
- Sequence-defined oligomer (1)
- Sequencing (1)
- Service life (1)
- Setting (1)
- Shale (1)
- Shape (1)
- Shape-controlled (1)
- Shear behavior (1)
- Shore Hardness (1)
- Shore-Härte (1)
- Short-distance diffusion (1)
- Shrinkage (1)
- Shrinkages (1)
- Si-Ge (1)
- SiO2 Nanoparticle (1)
- Sicherer Betrieb (1)
- Sicherheit (1)
- Sicherheitsdatenblatt (1)
- Silane (1)
- Silica (1)
- Silica coating (1)
- Silicoborate glasses (1)
- Silicon Carbide (1)
- Silver indium sulfide (1)
- SimCoLas (1)
- Single cell-ICP-ToF-MS (1)
- Single molecule (1)
- Single particle-ICP-ToF-MS (1)
- Single-dot spectroscopy (1)
- Single-source precursors (1)
- Singlet oxygen (1)
- Sintern (1)
- Size (1)
- Size distribution (1)
- Sliding wear (1)
- Slidng wear (1)
- Slow Crack Growth (SCG) (1)
- Slow crack growth (1)
- Small Angle Neutron Scattering (1)
- Small angle neutron scattering (1)
- Small-angle x-ray scattering (1)
- Soda-lime-silica (1)
- Sodium ion batteries (1)
- Soil (1)
- Soil incubation study (1)
- Sol-gel coating (1)
- Solidification Cracking (1)
- Solubilizer (1)
- Sonochemical synthesis (1)
- Sorption (1)
- Spaltkorrosion (1)
- Spannungsrelaxationsrisse (1)
- Spannungsriss (1)
- Spannungsrisskorrosion (1)
- Spar cap design (1)
- Spark plasma sintering (1)
- Speciation analysis (1)
- Specific Surface Area (BET) (1)
- Spectral irradiation (1)
- Spectroscopic Imaging (1)
- Spektrale Ellipsometrie (SE) (1)
- Spin (1)
- Spontaneous emulsification (1)
- Spring constant (1)
- Spring constant (1)
- SrTiO3 (1)
- Stabilität von Eigenspannungen (1)
- Stabilization (1)
- Stabstruktur (1)
- Stahl (1)
- Stahl und Aluminium (1)
- Stained glass (1)
- Stained glass windows (1)
- Stained glasses (1)
- Stand der Normung (1)
- Standardization of Ellipsometry (1)
- Stanzen (1)
- Static Mixing (1)
- Statistics (1)
- Stepwise growth (1)
- Stereocomplex (1)
- Stimuli-responsive polymers (1)
- Stochastic Landau Lifshitz equation (1)
- Stress analysis (1)
- Stress intensity factor (1)
- Stress-strain behavior (1)
- Structural analysis (1)
- Structural defects (1)
- Structural integrity (1)
- Structural safety (1)
- Structural sealant glazing (1)
- Structural steel (1)
- Structure-property relationship (1)
- Structured light scanning (1)
- Structures under extreme conditions (1)
- Struktur (1)
- Struvite (1)
- Sub-oxide (1)
- Subcritical crack growth (1)
- Substitution (1)
- Sulfur (1)
- Superalloy (1)
- Superconducting magnet (1)
- Supercritical CO2 (1)
- Supercritical/dense phase CO2 (1)
- Superimposed loading (1)
- Supermartensit (1)
- Supermartensitic Stainless Steel (SMSS) (1)
- Superparamagnetism (1)
- Surface Chemical Transformation (1)
- Surface Chemistry (1)
- Surface analysis (1)
- Surface characterization (1)
- Surface charge (1)
- Surface group (1)
- Surface group analysis (1)
- Surface group quantification (1)
- Surface roughness (1)
- Surface roughness analysis (1)
- Surface structures (1)
- Surfaces (1)
- Survey (1)
- Survival rates (1)
- Suzuki-Miyaura coupling (1)
- Swarming (1)
- Swept wavelength interferometry (1)
- Switch (1)
- Sychrotron tomography (1)
- Synchrotron CT (1)
- Synchrotron Energy Dispersive Diffraction (1)
- Synchrotron Röntgen Refraktion (1)
- Synchrotron X-ray diffraction (1)
- Synchrotron X-ray refraction radiography (1)
- Synchrotron X-ray tomography (1)
- Synchrotron X‐ray refraction radiography (1)
- Synchrotron computed tomography (1)
- Synchrotron radiation (1)
- Synchrotron x-ray refraction radiography (SXRR) (1)
- Synchrotronbeugung (1)
- TGA-FTIR (1)
- THz-TDS (1)
- TMF (1)
- TaC (1)
- Tafel Plot (1)
- Tankschifftyp (1)
- Tanning (1)
- Tantalum carbide (1)
- Tara Mediterranee (1)
- Technical crack detection (1)
- Technological innovation (1)
- Temperature effects (1)
- Temperature modulated differential scanning calorimetry (1)
- Temple Scroll (1)
- Tensile Stress (1)
- Tensile testing (1)
- Themral cycles (1)
- Therapeutic antibodies (1)
- Thermal analysis (1)
- Thermal arrier coatings (1)
- Thermal barrier coatings (1)
- Thermal conductivity device (1)
- Thermal expansion (1)
- Thermal extraction-desorption gas chromatography mass spectrometry (1)
- Thermal testing (1)
- Thermally-induced moisture transport (1)
- Thermische Belastung (1)
- Thermische Betriebsbelastungen (1)
- Thermische Dehnung (1)
- Thermo-fluid dynamics (1)
- Thermo-fluid flow (1)
- Thermo-responsive polymers (1)
- Thermodynamic analysis (1)
- Thermoelectric properties (1)
- Thermograhy (1)
- Thermogravimetry (1)
- Thermomechanics (1)
- Thermomechanik (1)
- Thermoplastic polyurethane (1)
- Thermoplastics (1)
- Thick materials (1)
- Thick shells (1)
- Thick-walled Structures (1)
- Thick-walled steel (1)
- Thick-walled steels (1)
- Thin film (1)
- Thin film systems (1)
- Thin magnetic films (1)
- Thiol-ene click chemistry (1)
- TiO2 (1)
- TiO2 nanoparticle (1)
- Time-gated emission (1)
- Time-resolved flow cytometry (1)
- Time-temperature superposition (1)
- Tin(II)octanoate (1)
- Titan-Halterung (1)
- Titanium dioxide (1)
- ToF-SIMS (1)
- Tomographie, (1)
- Tool steel (1)
- Topometry (1)
- Topotactic phase transitions (1)
- Torsional fatigue (1)
- Total scattering analysis (1)
- Toughness (1)
- Toxicity (1)
- Transformation pathways (1)
- Transient heat transfer (1)
- Transport und Lagerung von Chemikalien (1)
- Trastuzumab (1)
- Tribologische Datenbank (1)
- Tribologsches Charakterisierungsdienste (1)
- Trilobite compound eyes (1)
- Trinkwasserinstalltion (1)
- Triplet-triplet annihilation (1)
- Trojan silver artefacts (1)
- Tubular X-joints (1)
- Tuff (1)
- Tungsten-Rhenium (1)
- Tunnelatmosphöre (1)
- Two-Photon Polymerization (1)
- Two-dimensional hexagonal boron nitride(h-BN) (1)
- UCST polymers (1)
- UHMWPE (1)
- UN-Test O.3 (1)
- UV Vis (1)
- UV Weathering (1)
- UV-Bestrahlungsstärke (1)
- UV/VIS spectroscopy (1)
- Ultra-high strength steel (1)
- Ultrafast scattering (1)
- Ultraschallmessung (1)
- Ultraschallsensor (1)
- Ultraschallwellen (1)
- Ultrashort laser pulses (1)
- Ultrasonic measurement (1)
- Ultrasound (1)
- Uncertainty budget (1)
- Uncertainty budgets (1)
- Ungleichgewicht (1)
- Uniaxial compression tests (1)
- Unlegierter Baustahl (1)
- UpConversion (1)
- Upconverstion (1)
- VM12 SHC (1)
- Vacuum (1)
- Vacuum hot extraction (1)
- Varestraint (1)
- Verfleckungen (1)
- Vernetzung (1)
- Verschleiß (1)
- Verwitterung (1)
- Vickers (1)
- Vickers indentation (1)
- Viscoelastic model (1)
- Viscoplastic (1)
- Viscoplasticity (1)
- Viscous sintering (1)
- Viskosität (1)
- Vitual computer tomography simulation (1)
- Vorgehensweise (1)
- Vorhaben (1)
- WAXS (1)
- Warmfester Stahl (1)
- Wartung (1)
- Wasser (1)
- Wasserstoffspeicher (1)
- Wastewater (1)
- Water migration (1)
- Weathering resistance (1)
- Weißlichtinterferenzmikroskopie (WLIM, 3D) (1)
- Weld pool (1)
- Welding process simulation (1)
- Werkstoffauswahl (1)
- Werkstoffe (1)
- Werkstoffmechanische Prüfung (1)
- Wetting (1)
- White light interference microscopy(WLIM) (1)
- Wiederkehrende Prüfung (1)
- Wild bees (1)
- Wind rotor blade (1)
- Wirbelstrom (1)
- Wirbesltrom (1)
- Wood materials (1)
- X-ray (1)
- X-ray Absorption Spectroscopy (1)
- X-ray Photoelectron Spectroscopy (XPS) (1)
- X-ray absorption spectroscopy (1)
- X-ray imaging (1)
- X-ray microspectroscopy (1)
- X-ray spectroscopic techniques (1)
- X-ray spectroscopy (1)
- X8Ni9 (1)
- XAFS (1)
- XANES (1)
- Yb(III) complex (1)
- Year in Review (1)
- Young's modulus (1)
- Young´s modulus (1)
- Zement (1)
- Zeolitic Imidazolate Frameworks (1)
- Zeta potential (1)
- ZfP (1)
- Zinc (1)
- Zinc oxide (1)
- ZnO (1)
- Zug-Druck-Schubprüfung (1)
- Zugprüfungen (1)
- abtragende Glasbearbeitung (1)
- alumina (1)
- anion-exchange (1)
- antibody (1)
- arbidic austempered ductile iron (1)
- arbon capture (1)
- attraktive Wechelwirkung (1)
- bacteria (1)
- bacteria detection (1)
- beta particle (1)
- bioactive (1)
- biokompatibel (1)
- biomaterials (1)
- bone (1)
- carbon steel (1)
- ceramics (1)
- clustered nanoparticles (1)
- condensate (1)
- copper (1)
- degradation (1)
- deposition welding (1)
- dielectric spectroscopy (1)
- digital image correlation (1)
- dual phase steel (1)
- electrochemical characterization (1)
- ethylene vinyl acetate (1)
- fatigue crack growth (1)
- flow cytometry (1)
- fluorescence microscopy (1)
- gamma ray (1)
- gas separation membranes (1)
- geothermal energy (1)
- gesintert (1)
- high pressure (1)
- highspeed plasma laser cladding (1)
- i-Tribomat (1)
- immunoseparation (1)
- impurities (1)
- infrared spectroscopy (1)
- leakage (1)
- lifetime (1)
- magnetic nanoparticle (1)
- mechanical properties (1)
- method (1)
- microstructure analysis (1)
- molecular mobility (1)
- nanoindentation (1)
- nanoparticle (1)
- natural ventilation (1)
- pH (1)
- particle (1)
- performance test (1)
- phosphate glasses (1)
- pitting corrosion (1)
- polymers (1)
- polymers of intrinsic microporosity (1)
- polynorbornenes (1)
- product specification (1)
- quantum dot (1)
- quantum yield (1)
- radiolysis (1)
- resistance spot welding (1)
- rubber (1)
- screening tes (1)
- selective laser melting (1)
- shape control (1)
- single cell-ICP-ToF-MS (1)
- single particle-ICP-ToF-MS (1)
- steel (1)
- temeprature dependent exchange length (1)
- uncertainty (1)
- utilization, and storage (CCUS) technology (1)
- volume resistivity (1)
- water speciation (1)
- µ-XRF (1)
- Äquivalente Wärmequelle (1)
- μCT (1)
- кратер шва (1)
- кристаллизация, (1)
- плавление, (1)
- сварочная ванна (1)
- температурное поле (1)
- функция теплонасыщения (1)
Organisationseinheit der BAM
- 6 Materialchemie (229)
- 9 Komponentensicherheit (215)
- 7 Bauwerkssicherheit (164)
- 8 Zerstörungsfreie Prüfung (163)
- 5 Werkstofftechnik (161)
- 9.3 Schweißtechnische Fertigungsverfahren (118)
- 7.6 Korrosion und Korrosionsschutz (96)
- 8.5 Röntgenbildgebung (84)
- 6.6 Physik und chemische Analytik der Polymere (70)
- 1 Analytische Chemie; Referenzmaterialien (68)
Eingeladener Vortrag
- nein (443)
A novel cop olyme r based on supramolecular motif2,6-diaminopyridin e and water-soluble acrylamide, poly[N-(6-ace tamidopyridin-2-yl) acrylamide-co-acrylamide], was synthe-size d via rev ersible addi tion–fragmentation chain transfer (RAFT)polymerization with various monomer compositions. The thermo-respon sive behavior of the copolymers was studied by turbidime-try and dynamic light scattering (DLS). The obtained copolymersshowed an upper critical solution temperature (UCST)-typ e phasetransition behavior in water and electrolyte solution. The phasetransition temperature was found to increase with decreasingam ount of acrylamide in the copolymer and increasing concentra-tion of the solution. Furth ermore, the phase transition temperatureva ried in aqueous solutions of electrolytes according to the naturean d concentration of the electrolyte in accordance with theHoffmeister series. A dramatic solvent isotope effect on thetransition temperature was o bserved in this study, as the transitiontemperature was almost 10–12C higher in D2OthaninH2Oatthesame concentration and acrylamide co mposition. The size of theaggregates below the transition temperature was larger in D2Ocompared to that in H2O that can be explained by deuterium iso-tope effect. The thermoresponsive behavior of the copolymers wasalso investigated in different cell medium and found to be exhibitedUCST-type phase transition behavior in different cell medium.Such behavior of the copo lyme rs can be useful in many a pplica-tions including biomedical, microfluidics, optical materials, and indrug delivery.
The initial focus of this research was on the development of a general workflow for the documentation and monitoring of historical stained glass windows using structured light scanning.
Therefore windows from different churches, time periods and with different corrosion and damage phenomena were scanned before and after conservation measures.
The quality of components made by laser beam melting (LBM) additive manufacturing is naturally influenced by the quality of the powder bed. A packing density <1 and porosity inside the powder particles lead to intrinsic voids in the powder bed. Since the packing density is determined by the particle size and shape distribution, the determination of these properties is of significant interest to assess the printing process. In this work, the size and shape distribution, the amount of the particle’s intrinsic porosity, as well as the packing density of micrometric powder used for LBM, have been investigated by means of synchrotron X-ray computed tomography (CT). Two different powder batches were investigated: Ti–6Al–4V produced by plasma atomization and stainless steel 316L produced by gas atomization. Plasma atomization particles were observed to be more spherical in terms of the mean anisotropy compared to particles produced by gas atomization. The two kinds of particles were comparable in size according to the equivalent diameter. The packing density was lower (i.e., the powder bed contained more voids in between particles) for the Ti–6Al–4V particles. The comparison of the tomographic results with laser diffraction, as another particle size measurement technique, proved to be in agreement.
In this poster we will present some results of a research projects dealing with Arabic recipes of black inks. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed.
We will show procedures and problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on squid ink and mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol, the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts.
In this poster we will present some results of a research projects dealing with Arabic recipes of black inks [1-2]. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed.
We will show procedures and problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on squid ink [3] and mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect [4]. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol, the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts.
[1] A. Schopen, Tinten und Tuschen des arabisch-islamischen Mittelalters, Göttingen: Vandenhoeck & Ruprecht, 2004
[2] S. Fani, Le arti del libro secondo le fonti arabe originali. I ricettari arabi per la fabbricazione degli inchiostri (sec. IX-XIII): loro importanza per una corretta valutazione e conservazione del patrimonio manoscritto, PhD thesis, Napoli: Università L’Orientale, 2013
[3] S. Centeno, J. Shamir Journal of Molecular Structure, 873 (2008), 149-159
[4] C. Colini et. al, Manuscript cultures, 11 (2018) 43-50
In this poster we will present some results of a research projects dealing with Arabic recipes of black inks. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed.
First, we will provide an overview of the sources [1-2] employed in the study – dating from 9th to 14th century, although the manuscripts in which they can be found dates up to the 20th century – with an eye on the ink typologies (real and perceived by the compilers). Then we will show how, by reproducing the recipes, it was possible to shed light on some oddities in the procedures and the choice of ingredients. In the end we will discuss problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect [3]. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol and the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts.
[1] A. Schopen, Tinten und Tuschen des arabisch-islamischen Mittelalters, Göttingen: Vandenhoeck & Ruprecht, 2004
[2] S. Fani, Le arti del libro secondo le fonti arabe originali. I ricettari arabi per la fabbricazione degli inchiostri (sec. IX-XIII): loro importanza per una corretta valutazione e conservazione del patrimonio manoscritto, PhD thesis, Napoli: Università L’Orientale, 2013
[3] C. Colini et. al, Manuscript cultures, 11 (2018) 43-50
The mechanochemical formation of the ionic cocrystals of glucose (Glc) and sodium salts Glc2NaCl·H2O (1) and Glc2NaX (X = Br (2), I (3)) is presented. Products are formed by co-milling Glc with three sodium salts (NaCl, NaBr, NaI). The ionic cocrystals were obtained under both neat grinding and liquid-assisted grinding conditions, the later found to accelerate the reaction kinetics. The crystal structures of the ionic cocrystals (2) and (3) were solved from powder X-ray diffraction data. The structure solution contrasts with the structure of Glc2NaCl·H2O (1) where the electron density at three halide crystallographic sites is modeled as of being the intermediate between water molecule and a chloride ion. The reaction pathways of the three ionic cocrystals were investigated in real time using our tandem approach comprising a combination of in situ synchrotron powder X-ray diffraction and Raman spectroscopy. The results indicate the rapid formation of each cocrystal directly from their respective starting materials without any intermediate moiety formation. The products were further characterized by DTA-TG and elemental analysis.
The weld pool dynamics and shape play a fundamental role in keyhole mode welding. The presented work aims the experimental and numerical investigation of the influence of the weld pool characteristics on the formation of hot cracking. The experimental procedure allows recording the molten pool in the longitudinal section of a butt joint configuration of 15 mm thick structural steel and transparent quartz glass by using a high-speed video camera and two thermal imaging cameras. The observations show that the dimensions of the weld pool vary depending on the depth. The regions close to the surface form a teardrop-shaped weld pool. A bulge-region and its temporal evolution are observed approximately in the middle of the depth of the weld pool, where hot cracking appears. A numerical framework including models for the weld pool dynamics, global temperature field, transient stress state, crystal growth, diffusion and macro-segregation and subroutines for their one-way couplings is developed. The numerically obtained and experimentally observed results are in a good agreement. It is shown that the bulge-region leads to a delay in the solidification behavior, increased temporal tensile stresses and accumulation of impurities in the defect region and hence enhance the probability of hot cracking formation.
By means of a small-scale truss bridge, the ability of the Measurement- and Model-based Structural Analysis to detect and localize damage was examined. Although there was no noteworthy difficulty in detecting damage, it turned out that damage localization responds sensitively to systematic influences, i.e. non-modelled properties of the mechanical model. Therefore, another experiment is being conducted to re-examine the Measurement- and Model-based Structural Analysis. For this purpose, the bending test is carried out as it has been already theoretically respectively numerically discussed. In this attempt, the systematic influences such as residual stress are kept as low as possible.
A look inside nanoparticles
(2019)
Small-angle scattering is the method of choice when it comes to obtaining information about the interior of nanoparticles. The aim is to make nanotechnology safer. While the use of small-angle neutron scattering (SANS) is limited to a few instruments in the world, small-angle X-ray scattering (SAXS) is widely accessible, with an upward trend. The example of core-shell particles shows how simple their analysis is with data from an Anton Paar laboratory system. Here, SAXS is a central tool for the development of new reference materials based on poly(methyl) acrylate-PVDF core-shell particles. The dimensions of the cores and shells can be precisely determined. A detailed analysis makes it possible to show that the cores contain fluorinated and nonfluorinated polymers, whereas the shell consist only of PVDF. This core-shell particles with a diameter around 40 nm show a significantly higher PVDF beta phase content than the PVDF homopolymer when using an emulsion polymerization technique. This finding is of importance with respect to applications in electroactive devices.
Additive Manufacturing (AM) in terms of laser powder-bed fusion (L-PBF) offers new prospects regarding the design of parts and enables therefore the production of lattice structures. These lattice structures shall be implemented in various industrial applications (e.g. gas turbines) for reasons of material savings or cooling
channels. However, internal defects, residual stress, and structural deviations from the nominal geometry are unavoidable.
In this work, the structural integrity of lattice structures manufactured by means of L-PBF was non-destructively investigated on a multiscale approach.
A workflow for quantitative 3D powder analysis in terms of particle size, particle shape, particle porosity, inter-particle distance and packing density was established.
Synchrotron computed tomography (CT) was used to correlate the packing
density with the particle size and particle shape. It was also observed that at least about 50% of the powder porosity was released during production of the struts.
Struts are the component of lattice structures and were investigated by means of laboratory CT. The focus was on the influence of the build angle on part porosity and surface quality. The surface topography analysis was advanced by the quantitative characterisation of re-entrant surface features. This characterisation was compared with conventional surface parameters showing their complementary
information, but also the need for AM specific surface parameters.
The mechanical behaviour of the lattice structure was investigated with in-situ CT under compression and successive digital volume correlation (DVC). The Deformation was found to be knot-dominated, and therefore the lattice folds unit cell layer wise.
The residual stress was determined experimentally for the first time in such lattice structures. Neutron diffraction was used for the non-destructive 3D stress investigation. The principal stress directions and values were determined in dependence of the number of measured directions. While a significant uni-axial stress state was found in the strut, a more hydrostatic stress state was found in the knot. In both cases, strut and knot, seven directions were at least needed to
find reliable principal stress directions.
This work aims to find the thermal cycles during and after fusion welding through simulation by first calculating the resulting local temperature field in the quasi-stationary part of the process. Here complete-penetration keyhole laser beam welding with a laser power of 18 kW on a 15 mm thick slab of a low-alloyed steel at a welding speed of 2 m/min is considered. In order to physically depict the laser material interaction a multi-physics numerical model including the effects of phase transformation, thermo-capillary convection, natural convection and temperature-dependent material properties up to evaporation temperature is developed. It uses a fixed keyhole geometry with a right truncated circular cone shape to introduce the laser beam energy to the workpiece. In a subsequent study, the resulting local temperature field is then used as an equivalent heat source in order to predict the unsteady thermal cycle during and after fusion welding. The translational movement of the laser beam through the workpiece is represented by a moving mesh approach. For the simulation, stationary heat transfer and fluid dynamics are described by a system of strongly coupled partial differential equations. These are solved with the commercial finite element software COMSOL Multiphysics 5.0. The results of the numerical simulation are validated by experiments, where the weld bead shapes and the thermal cycles show good correlation.
Additive manufacturing of alkali-activated materials currently attracts a lot of attention, because of the possibility to produce customized high-performance elements for a range of applications, potentially being more resource-efficient than conventionally produced parts. Here, we describe a new additive manufacturing process for alkali-activated materials that is based on selective laser-heating of lithium aluminate/microsilica slurries. The new process-material combination allows to manufacture elements with complex geometries at high building rates and high accuracy. The process is versatile and transferrable to structures of sizes differing by orders of magnitude. The mechanical strength of the obtained materials was in the range of values reported for conventional metakaolin-based geopolymers, and superior to what has been hitherto reported for alkali-activated materials produced by additive manufacturing. This mechanical performance was obtained despite the fact that the degree of reaction of the lithium aluminate and the microsilica was low, suggesting that significant reactions took place only at the surface of the microsilica particles.
The Measurement- and Model-based Structural Analysis (MeMoS) integrates a finite element model into least squares adjustment and thus allows to evaluate a mechanical model and measurements in a combined analysis. To examine the capability to detect and localise damage using this integrated analysis MeMoS, a small-scale truss bridge made of aluminium profiles is built as a test specimen for this purpose.
Laser-induced periodic surface structures (LIPSS, ripples) are a universal phenomenon that can be observed on almost any material after the irradiation by linearly polarized laser beams, particularly when using ultrashort laser pulses with durations in the femtosecond to picosecond range.
During the past few years significantly increasing research activities have been reported in the field of LIPSS, since their generation in a single-step process provides a simple way of nanostructuring and surface functionalization towards the control of optical, mechanical, biological, or chemical surface properties. In this contribution the mechanisms of formation and current applications of LIPSS are reviewed, including the colorization of technical surfaces, the control of surface wetting properties, the mimicry of the natural texture of animal integuments, the tailoring of surface colonization by bacterial biofilms, the advancement of medical pacemakers, and the improvement of the tribological performance of nanostructured metal surfaces.
Mesoporous phosphates are a group of nanostructured materials with promising applications, particularly in biomedicine and catalysis. However, their controlled synthesis via conventional template-based routes presents a number of challenges and limitations. Here, we show how to synthesize a mesoporous Magnesium phosphate with a high surface area and a well-defined pore structure through thermal decomposition of a crystalline struvite (MgNH4PO4·6H2O) precursor. In a first step, struvite crystals with various morphologies and sizes, ranging from a few micrometers to several millimeters, had been synthesized from supersaturated aqueous solutions (saturation index (SI) between 0.5 and 4) at ambient pressure and temperature conditions. Afterwards, the crystals were thermally treated at 70–250 °C leading to the release of structurally bound water (H2O) and ammonia (NH3). By combining thermogravimetric analyses (TGA), scanning and transmission electron microscopy (SEM, TEM), N2 sorption analyses and small- and wide-angle X-ray scattering (SAXS/WAXS) we show that this decomposition process results in a pseudomorphic transformation of the original struvite into an amorphous Mg-phosphate. Of particular importance is the fact that the final material is characterized by a very uniform mesoporous structure with 2–5 nm wide pore channels, a large specific surface area of up to 300 m2 g−1 and a total pore volume of up to 0.28 cm3 g−1. Our struvite decomposition method is well controllable and reproducible and can be easily extended to the synthesis of other mesoporous phosphates. In addition, the so produced mesoporous material is a prime candidate for use in biomedical applications considering that Magnesium phosphate is a widely used, non-toxic substance that has already shown excellent biocompatibility and biodegradability.
The additional element from the filler wire in the laser beam welding is usually distributed inhomogeneously in the final weld due to the high solidification rate of weld pool. It has been found that the electromagnetic stirring produced by an external oscillating magnetic field can enhance the material mixing in the weld pool to achieve a more uniform element distribution. However, the magnetic field has a highly non-linear and multi-coupled interaction with the weld pool behavior, which makes the quantitative explanation of the physical mechanism difficult. In this study, the effect of electromagnetic stirring on the transport phenomena in the wire feed laser beam welding is investigated by a numerical modelling. A 3D transient multi-physical model considering the magnetohydrodynamics, heat transfer, fluid flow, keyhole dynamics and element transport is developed. The multiple reflections and the Fresnel absorption of the laser on the keyhole wall are calculated using the ray tracing method. The numerical results show that a Lorentz force produced by the oscillating magnetic field and its induced eddy current gives significant influence on the transport phenomena in the molten pool. The forward and downward flow is enhanced by the electromagnetic stirring, which homogenizes the distribution of the additional elements from a nickel-based filler wire in a steel weld pool. The numerical results show a good agreement with the high-speed images of the molten pool, the fusion line from the optical micrograph and the element distribution from the energy dispersive X-ray spectroscopy. This work provides a physical base for the electromagnetic-controlled laser beam welding and some guidance for the selection of electromagnetic parameters.
The additional element from the filler wire in the laser beam welding is usually distributed inhomogeneously in the final weld due to the high solidification rate of weld pool. It has been found that the electromagnetic stirring produced by an external oscillating magnetic field can enhance the material mixing in the weld pool to achieve a more uniform element distribution. However, the magnetic field has a highly non-linear and multi-coupled interaction with the weld pool behavior, which makes the quantitative explanation of the physical mechanism difficult. In this study, the effect of electromagnetic stirring on the transport phenomena in the wire feed laser beam welding is investigated by a numerical modelling. A 3D transient multi-physical model considering the magnetohydrodynamics, heat transfer, fluid flow, keyhole dynamics and element transport is developed. The multiple reflections and the Fresnel absorption of the laser on the keyhole wall are calculated using the ray tracing method. The numerical results show that a Lorentz force produced by the oscillating magnetic field and its induced eddy current gives significant influence on the transport phenomena in the molten pool. The forward and downward flow is enhanced by the electromagnetic stirring, which homogenizes the distribution of the additional elements from a nickel-based filler wire in a steel weld pool. The numerical results show a good agreement with the high-speed images of the molten pool, the fusion line from the optical micrograph and the element distribution from the energy dispersive X-ray spectroscopy. This work provides a physical base for the electromagnetic-controlled laser beam welding and some guidance for the selection of electromagnetic parameters.
To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit.
To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit.
The precise analysis of cation diffusion profiles through corrosion scales is an important aspect to evaluate corrosion phenomena under multicomponent chemical load, as during high‐temperature corrosion under deposits and salts. The present study shows a comprehensive analysis of cation diffusion profiles by electron microprobe analysis and microbeam X‐ray absorption near edge structure (µ‐XANES) spectroscopy in mixed oxide/sulfide scales grown on Fe–Cr model alloys after exposing them to 0.5% SO2. The results presented here correspond to depth‐dependent phase identification of oxides and sulfides in the corrosion scales by µ‐XANES and the description of oxidation‐state‐dependent diffusion profiles. Scales grown on low‐ and high‐alloyed materials show both a well‐pronounced diffusion profile with a high concentration of Fe3+ at the gas and a high concentration of Fe2+ at the alloy interface. The distribution of the cations within a close‐packed oxide lattice is strongly influencing the lattice diffusion phenomena due to their different oxidation states and therefore different crystal‐field preference energies. This issue is discussed based on the results obtained by µ‐XANES analysis.
Structural modularity of polymer frameworks is a key advantage of covalent organic polymers, however, only C, N, O, Si and S have found their way into their building blocks so far. Here, we expand the toolbox available to polymer and materials chemists by one additional nonmetal, phosphorus. Starting with a building block that contains a λ⁵‐phosphinine (C₅P) moiety, we evaluate a number of polymerisation protocols, finally obtaining a π‐conjugated, covalent phosphinine‐based framework (CPF‐1) via Suzuki‐Miyaura coupling. CPF‐1 is a weakly porous polymer glass (72.4 m2 g‐1 N2 BET at 77 K) with green fluorescence (λmax 546 nm) and extremely high thermal stability. The polymer catalyzes hydrogen evolution from water under UV and visible light irradiation without the need for additional co‐catalyst at a rate of 33.3 μmol h‐¹ g‐¹. Our results demonstrate for the first time the incorporation of the phosphinine motif into a complex polymer framework. Phosphinine‐based frameworks show promising electronic and optical properties that might spark future interest in their applications in light‐emitting devices and heterogeneous catalysis.
L-Lactide was polymerized in bulk with tin(II)2-ethylhexanoate SnOct2) as catalyst and salicylic acid as cocatalyst. The Lac/Cat ratio, Cocat/Cat ratio, temperature and time were varied. Increasing Cocat/Cat ratios reduced both,polymerization rate and molecular weight. However,under optimized conditions high molar mass (Mw up to 178,000), colorless, cyclic polylactides were formed in a short time. A few polymerizations performed at 160 and 180°C with the combination of SnOct2 and silylated salicylic acid gave similar results. Neat tin II) salicylate was prepared from SnOct2 and used for REPs of L-lactide in bulk, but the results were not better than those obtained from combinations of SnOct2 and salicylic acid. Furthermore, dibutyltin salicylate was synthesized and used as catalyst for polymerizations of L-lactide in bulk at temperatures varying from 102 to 160°C. Cyclic polylactides with Mw’s up to 40,000 were the main reaction products. At 100–102°C a predominance of odd-numbered cycles was found proving a REP mechanism.
Carbidic Austempered Ductile Iron (CADI) microstructures containing eutectic carbides can be produced by the addition of carbide stabilizing elements, such as chromium. Carbides formed from the addition of Cr are eutectic of M3C type. The presence of such hard phases can enhance the abrasion wear resistance of ductile iron. A new CADI can be produced by the addition of Nb. Niobium carbide particles are formed in the beginning of solidification and remain stable once they are insoluble in solid iron matrix. The dry sand abrasive wear resistance of ductile irons alloyed with 1.0, 1.8, and 2.4 wt% Nb were tested in both “as-cast” and “heat treated” conditions using standard ASTM G65. Results were compared to abrasive wear data obtained on ductile iron alloyed with 1 wt% Cr, CADI (1 wt% Cr), and the basic composition of iron without carbide stabilizing elements. In the “ascast” condition, the addition of Nb did not lead to a reduction in wear, while CADI with Nb is a promising substitute for CADI with Cr addition, because both materials showed very similar values of abrasion resistance.
Micro-ploughing and micro-cutting mechanisms were observed on the worn surfaces of ductile irons. Abrasive wear resistance of these alloys was correlated with the volume fraction of carbides.
Nachdem im Verbundprojekt COORAL das Hauptaugenmerk auf überkritisches CO2 gelegt wurde, d. h. Transport über kurze Strecken bei erhöhter Temperatur, wurde in CLUSTER ein größeres lokales Transport-Netzwerk betrachtet, bei dem CO2 bei geringeren Temperaturen, also vorwiegend im flüssigen Zustand transportiert wird. Wurden in COORAL die CO2-Ströme von Kohlekraftwerken untersucht, ging es in CLUSTER zusätzlich um die Emissionen von relevanten Industrien, deren CO2-Emissionen nicht ohne Weiteres vermieden werden können.
Aufgrund der Erfahrungen in COORAL konnte eine Auswahl von kommerziellen Werkstoffen getroffen werden, die für einen konkreten Einsatz für CCS zur Verfügung stünden. Die gemischten und fluktuierenden CO2-Zusammensetzungen sind bei geeigneten Begrenzungen der Begleit¬stoffe im CO2 bezüglich Korrosionsvorgänge beherrschbar. Die Machbarkeit eines lokalen CCS-Clusters erscheint daher gegeben, soweit dies die Anlagen für Kompression, Transport und Injektion betrifft.
Im Fokus des Vorhabens steht das mit dem Innovationspreis Berlin-Brandenburg 2012 ausgezeichnete Mehr-Proben-Prüfverfahren zur Festigkeitsprüfung unter Verwendung einer analytischen Zentrifuge mit dem Ziel des Einsatzes in der Qualitätssicherung. Nachdem im MNPQ-Projekt QUO VADIS die grundsätzliche Anwendbarkeit der Zentrifugentechnologie auf Beanspruchungen auf Zug (Kleb-, Haft- und Verbundfestigkeit) nachgewiesen worden war, wurden im Vorhaben QUO VADIS PLUS folgende erweiterte Prüfszenarien und technische Weiterentwicklungen etabliert: 1. Beanspruchung auf Druck (Härte von Materialien, Kompressibilität von Schäumen, Kompaktierbarkeit von Pulvern), 2. Erweiterung der Beanspruchung auf Zug (Kombination von Normal- und Lateralkräften), 3. Erweiterung auf die Bewertung plasto-elastischenn Materialverhaltens, 4. Vermeidung von Schockwellen im Hochlastbereich
Die Präsentation gibt einen Überblick bezüglich der von der BAM im Rahmen des SimCoLas Verbundprojekts durchgeführten Arbeiten zum Thema "Photonische Prozessketten". Die numerisch abgebildete Prozesskette Tiefziehen/Laserstrahlschweißen wird darsgestellt und diskutiert. Fokus der Diskussion ist die entwickelte Methodik zur konsistenten Abbildung numerischer Prozessketten mit der Applikation Heissrisskritikalität beim Laserstrahlschweißen.
The influence of size effects on the thermoelectric properties of thin platinum films is investigated and compared to the bulk. Structural properties, like the film thickness and the grain size, are varied. We correlate the electron mean free path with the temperature dependence of the electrical conductivity and the absolute Seebeck coefficient SPt of platinum. A measurement platform was developed as a standardized method to determine SPt and show that SPt,film is reduced compared to SPt,bulk. Boundary and surface scattering reduce the thermodiffusion and the phonon drag contribution to SPt,film by nearly the same factor. We discuss in detail on behalf of a model, which describes the temperature dependence of the absolute Seebeck coefficient, the influence of size effects of electron-phonon and phonon-phonon interaction on SPt.
For a better understanding of the damage of glued wood tensile tests on miniature specimens made of glued spruce wood with acoustic emission and in-situ synchrotron-based X-ray computer microtomography has been monitored. As adhesive, urea-formaldehyde resin was used. For comparison purposes, tensile tests were carried out on solid wood and bonded miniature tensile shear samples with acoustic emission. The acoustic emission signals of all experiments were with classified pattern recognition. This resulted in two classes of signals for each two frequency peaks. In one class was the low-frequency, in the other the higher frequency peak of higher intensity, but this essentially independent from the structure (solid wood or plywood) and the size scale of the test specimens. The influence of the adhesive layers was determined on plywood test specimens in laboratory scale and on miniature test specimens with an adhesive layer and selected fiber orientations examined. This gave evidence that the sound emission signals from the failure of the adhesive layer presumably of the class with low frequency signals peak in the range of services can be assigned.
Additively manufactured test specimens made of polyamide 12 (PA 12) by Laser Sintering as well as of acrylonitrile butadiene styrene (ABS) by Fused Layer Modelling, were characterised with active thermography directly after manufacturing and after artificial weathering. For this, two different excitation methods (flash and pulse heating) were used and compared, regarding their suitability for the detection of constructed and imprinted defects inside the test specimens. To increase the quality of the thermograms, data processing methods like thermal signal reconstruction (TSR) and Fourier Transformation after TSR were applied. To further investigate the long-term stability of the additively manufactured test specimens towards environmental stress, like UV radiation, heat, humidity, water contact and frost with active thermography, an artificial weathering test over 2000 hours (~3 months) was applied to the specimens. The monitoring of the changes in the optical properties of the weathered plastics was supplemented by spectral reflectance and UV/VIS spectroscopy.
During a European convention of the authorities for market surveillance (AdCO) for explosives the activities of the notified bodies are presented, putting a focus on matters concerning market surveillance.
The presentation outlined in detail, which verifications are possible
with explosives, while practical tests involving initiation of
explosives are excluded. Elements of labeling and the conclusions in
view of quality control were explained, and typical failures by
manufacturers to comply were orally described.
Additive Fertigungsverfahren gewinnen aufgrund der schnellen, flexiblen und kosten-günstigen Fertigung von Bauteilen zunehmend an Bedeutung. Das Laserpulverauf-tragschweißen (LPA) wurde anfangs hauptsächlich als Beschichtungsverfahren ein-gesetzt. Diese Technologie bewerkstelligt aber auch das Reparieren von verschlisse-nen Bauteilen, sodass diese zeitsparend und ressourcenschonend erneuert werden können. Die hohe Aufbaurate, die flexible Pulverzusammensetzung sowie die hohe Endkonturnähe ermöglichen heutzutage die Entwicklung und additive Fertigung von neuen Materialien, wie zum Beispiel Nickel-Titan-Formgedächtnislegierungen.
Powder bed -based technologies are amongst the most successful Additive Manufacturing (AM) techniques. "Selective laser sintering/melting" (SLS/SLM) and "binder jetting 3D printing" (3DP) especially are leading AM technologies for metals and polymers, thanks to their high productivity and scalability. In this context, the "layerwise slurry deposition" (LSD) has been developed as a layer deposition method which enables the use of SLS/SLM and 3DP technologies for advanced ceramic materials. LSD consists in the layer-by-layer deposition of a ceramic slurry by means of a doctor blade. Each layer is deposited and dried to achieve a highly packed powder layer, which can be used for SLM or for 3DP. This technique offers high flexibility in the ceramic feedstock used, especially concerning material and particle size, and is capable of producing parts with physical and mechanical properties comparable to traditionally shaped parts. In this presentation, the LSD technique will be introduced and several examples of application to porcelain, SiC and alumina products will be reported.
The layerwise slurry deposition (LSD) has been established in the recent years as a method for the deposition of ceramic powder layers. The LSD consists in the layer-by-layer deposition of a ceramic slurry by means of a doctor blade; each layer is sequentially deposited and dried to achieve a highly packed powder layer.
The combination of binder jetting and LSD was introduced as a novel technology named LSD-print. The LSD-print takes advantage of the speed of binder jetting to print large areas, parallel to the flexibility of the LSD, which allows the deposition of highly packed powder layers with a variety of ceramic materials.
The working principle and history of the LSD technology will be shortly discussed. A theoretical background will be also discussed, highlighting advantages and drawbacks of the LSD compared to the deposition of a dry powder.
The last part of the talk will be dedicated to highlight recent results on the LSD-print of SiSiC of geometrically complex components, in collaboration between BAM and HC Starck Ceramics GmbH. Density, microstructure and mechanical properties of LSD-printed and isostatic pressed samples will be discussed and compared.
3D microstructures with sub-micron resolution can be manufactured in additive manner applying multi-photon laser structuring technique. This paper is focused on the incorporation of superparamagnetic iron oxide nanoparticles into the photoresist in order to manufacture micrometer-sized devices featuring a magnetic moment. The aim of the project is to achieve untethered actuation of the presented objects through externally applied magnetic fields. Future medical application scenarios such as drug delivery and tissue engineering are targeted by this research.
During their lifetime, polymer components subjected to mechanical loads and environmental influences show a loss of their mechanical properties required for their specific applications. In this respect, the craze-crack damage mechanism slow crack growth (SCG) is relevant for PE-HD components used in high-performance applications such as pipes and containers for the storage and transport of dangerous goods. SCG is considered to be the major failure mechanism in polyolefins and it typically occurs suddenly and unexpectedly. Due to the fields of application, SCG is a safety relevant issue. To test for the resistance of PE-HD pipe and container materials against SCG, the full-notch creep test (FNCT) is widely applied in Europe. In this study, SCG phenomena in PE-HD are investigated in detail based on an improved FNCT, especially including the consideration of the influence of environmental liquids effecting the damage mechanism. Using an enhanced fracture surface and a crack propagation analysis with imaging techniques such as light microscopy (LM), laser scanning microscopy (LSM), X-ray computed tomography (CT-scan) and scanning electron microscopy (SEM), detailed data concerning SCG are obtained.
The combined application of FNCT and such imaging techniques is explicitly advantageous and recommended to gain important information on damage occurring to PE-HD induced by mechanical stress and the influence of environmental liquids, which is essential within the Fourth Industry Revolution.
This book provides a state‐of‐the‐art overview on the processing, characterization, and modelling of metallic and ceramic materials used for energy and environmental applications. 17 scientists show a collection of current knowledge in 8 chapters.
This book fulfills its intention to provide a reference book containing a collection of publications on thin films and coatings made of ceramic and metals used for energy and environmental applications. It covers a broad range of this topic and provides a comprehensive insight. Graduate and undergraduate students of materials science and mechanical engineering can find an overview on this topic to step in this interesting field of engineering.
Powder bed -based technologies are amongst the most successful Additive Manufacturing (AM) techniques. "Selective laser sintering/melting" (SLS/SLM) and "binder jetting 3D printing" (3DP) especially are leading AM technologies for metals and polymers, thanks to their high productivity and scalability.
However, the flowability of the powder used in these processes is essential to achieve defect-free and densely packed powder layers. For standard powder bed AM technologies, this limits the use of many raw materials which are too fine or too cohesive.
This presentation will discuss the possibilities to either optimize the powder raw material to adapt it to the specific AM process, or to develop novel AM technologies which are able to process powders in a wider range of conditions.
In this context, the "layerwise slurry deposition" (LSD) has been developed as a layer deposition method which enables the use of very fine ceramic particles.
Powder bed -based technologies are amongst the most successful Additive Manufacturing (AM) techniques. "Selective laser sintering/melting" (SLS/SLM) and "binder jetting 3D printing" (3DP) especially are leading AM technologies for metals and polymers, thanks to their high productivity and scalability.
However, the flowability of the powder used in these processes is essential to achieve defect-free and densely packed powder layers. For standard powder bed AM technologies, this limits the use of many raw materials which are too fine or too cohesive.
This presentation will discuss the possibilities to either optimize the powder raw material to adapt it to the specific AM process, or to develop novel AM technologies which are able to process powders in a wider range of conditions.
In this context, the "layerwise slurry deposition" (LSD) has been developed as a layer deposition method which enables the use of very fine ceramic particles. Another technology, the Gas Flow Assisted Powder Deposition, can increase the stability of the powder bed and the packing density, even in extreme conditions such as in absence of gravitational forces.
The rational synthesis and use of nanomaterials require the characterization of many different properties, ranging from particle size and size distribution over surface chemistry to more applicationrelevant features like optical, electrochemical, and magnetic properties. In the following, several methods for the characterization of functional groups on nanomaterials, like polymer and silica nanoparticles, semiconductor quantum dots, and lanthanide-based upconversion nanocrystals are presented. Additionally, procedures for the measurement of the key spectroscopic performance parameters of nanomaterials with linear and nonlinear photoluminescence, such as the photoluminescence quantum yield, are presented for the UV/vis/NIR/SWIR.
Therapeutische Antikörper sind innerhalb weniger Jahre zur wichtigsten pharmazeutischen Produktklasse aufgestiegen. Für 2023 werden weltweite Umsätze von über 200 Milliarden USD erwartet. Auch diagnostische Antikörper sind mittlerweile unverzichtbare Produkte, auf deren Basis zahllose Immunoassays und andere Schnelltests entwickelt wurden. Neben der bereits sehr aufwendigen Herstellung von Antikörpern ist deren Aufreinigung aus komplexen Zellkulturmedien oder Blutseren und -plasmen zu einem Engpass in der Produktion und Nutzung dieser komplexen Proteine geworden. Schnelle und einfache Reinigungsmethoden für Antikörper sind daher sehr gefragt.
An overview of the BAM funed Focus Area Materials Project "AGIL" will be presented. AGIL focussed on the stdiy of the ageing characteristics of additively manufactured austenitic stainless steel with a "powder to mechanical failure" Approach. Recent Highlights are presented and a perspective for future studies.
At BAM, which is a federal institute for materials research and testing in Germany, it is one of our tasks to evaluate the safety of casks designed for transport and/or storage of radioactive material. This includes assessment of elastomeric seals applied in the casks. One of the aims is to identify a suitable method for estimating the service lifetime of the seals with regard to the requirements for long-term safety (40 years and more) of the containers. Therefore, we started an accelerated ageing programme with selected rubbers often used for seals (HNBR, EPDM and FKM) which are aged at four different temperatures (75 °C, 100 °C, 125 °C and 150 °C) for up to five years. In order to assess sealability, O-rings were aged in compression by 25 % (corresponding to the compression during service) between plates as well as in flanges that allow leakage rate measurements. For comparison, uncompressed O-rings were aged as well. In order to understand the underlying ageing mechanisms in each material, material properties such as hardness, density and tensile properties were examined. Additionally, compression set (CS), which represents the recovery behaviour of a seal after release from compression, is measured. For obtaining results closely related to practical conditions, O-rings with a full-scale cord diameter of 10 mm were aged. However, this set-up can lead to heterogeneous ageing caused by diffusion-limited oxidation (DLO) effects especially for HNBR, resulting in distorted bulk properties such as compression set. However, if DLO-affected data is excluded, extrapolations of CS data are possible using time-temperature shifts.
For selecting an appropriate end-of-lifetime criterion, leakage rate measurements were performed, since leakage rate is the only characteristic directly correlated to the performance of the sealing system. A significant increase in leakage rate was considered as the end of the lifetime. However, the O-rings remained leak tight under static conditions even though material properties had already degraded strongly. For this reason, a modified, more demanding leakage test involving a fast small decompression of the seal was developed that allowed determining a more conservative end-of-lifetime criterion with a safety margin for EPDM seals. FKM, which is a very heat and oxidation resistant material, exhibited only little degradation, even though it had the smallest activation energy.
AKR an Betonfahrbahndecken - ausgewählte Einflussgrößen und neuartige AKR-Vermeidungsstrategie
(2019)
In den letzten Jahren sind im deutschen Bundesautobahnnetz vermehrt Schäden an vor 2005 hergestellten Betonfahrbahndecken aufgetreten, die mit einer Alkali-Kieselsäure-Reaktion(AKR) in Verbindung gebracht werden. Vor diesem Hintergrund werden in diesem Beitrag zunächst die Voraussetzungen und ausgewählte Einflussgrößen für eine schädigende AKR aufgezeigt.
Besondere Aufmerksamkeit wird dabei der Rolle des Tausalzeintrags durch den Winterdienst bei Betonfahrbahndecken geschenkt. So wird mit Löseversuchen in 1 M KOH-Lösung zweier Gesteinskörnungen bei 80 °C gezeigt, dass mit zunehmender NaCI-Zugabe die Löslichkeit von SiÖ2 zunimmt und die von AI2O3 eine Verminderung erfährt. Basierend auf dem so exemplarisch erbrachten Nachweis für die Verstärkung der schädigenden AKR durch das Tausalz wird die Notwendigkeit und Richtigkeit der Durchführung von AKR-Betonversuchen mit Alkalizufuhr im ARS 04/2013 zur zukünftigen Vermeidung von AKR-Schäden an Betonfahrbahndecken im Rahmen von Neubau- und Erneuerungsmaßnahmen im Bundesfernstraßennetz belegt. Zusätzlich durchgeführte WS-Grundprüfungen nach dem ARS 04/2013 mit den beiden Gesteinskörnungen der Löse versuche veranschaulichen, dass die nach der Alkali-Richtlinie des DAfStb als unbedenklich eingestuften Gesteinskörnungen bei den Betonversuchen mit Alkalizufuhr durchaus als alkaliempfindlich bewertet werden können. Dies wiederum führt zu einer Verminderung der für den Betonstraßenbau verfügbaren Gesteinskörnungen.
Vor diesem Hintergrund wird nach neuartigen AKR-Vermeidungsstrategien gesucht, die auch eine Verwendung der als grenzwertig alkaliempfindlich eingestuften Gesteinskörnungen erlaubt.
Einen möglichen Lösungsansatz stellt in diesem Kontext die Innenhydrophobierung des Fahrbahndeckenbetons dar. Es soll so durch die Behinderung des Feuchte- und Tausalzeintrags in den Beton der AKR-Schädigungsprozess signifikant vermindert werden. Für die Bewertung der Leistungsfähigkeit der Innenhydrophobierung zur Vermeidung bzw. Verminderung einer schädigenden AKR in Betonfahrbahndecken wird zurzeit im Aufträge der BASt an der BAM ein Forschungsvorhaben bearbeitet. Im Rahmen dieses Beitrags werden erste Ergebnisse dieses Projekts vorgestellt. So wird exemplarisch an einem Oberbeton (D > 8)/Unterbeton und einem Oberbeton 0/8 mit einer alkaliempfindlichen Gesteinskörnung der Einfluss zweier Hydrophobierungsmittel auf die Frisch- und Festbetoneigenschaften ganzheitlich aufgezeigt und bewertet. Bei Letzteren stehen zunächst die mechanischen und hygrischen Parameter sowie der Frost-Tausalzwiderstand im Vordergrund. In einem weiteren Schritt wird der Einfluss beider Hydrophobierungsmittel auf die schädigende AKR mittels AKR-Betonversuchen mit Alkalizufuhr beleuchtet. Dabei gelangen ergänzend zur Beurteilung des Tausalzeintrags die Laser-Induced Breakdown Spectroscopy (LIBS) und zur Bewertung der Ausprägung der AKR und sekundären Ettringitbildung (SEB) die Dünnschliffmikroskopie zum Einsatz.
AKR an Betonfahrbahndecken - ausgewählte Einflussgrößen und neuartige AKR-Vermeidungsstrategie
(2019)
In den letzten Jahren sind im deutschen Bundesautobahnnetz vermehrt Schäden an vor 2005 hergestellten Betonfahrbahndecken aufgetreten, die mit einer Alkali-Kieselsäure-Reaktion (AKR) in Verbindung gebracht werden. Vor diesem Hintergrund werden in diesem Beitrag zunächst die Voraussetzungen und ausgewählte Einflussgrößen für eine schädigende AKR aufgezeigt.
Besondere Aufmerksamkeit wird dabei der Rolle des Tausalzeintrags durch den Winterdienst bei Betonfahrbahndecken geschenkt. So wird mit Löseversuchen in 1 M KOH-Lösung zweier Gesteinskörnungen bei 80 °C gezeigt, dass mit zunehmender NaCI-Zugabe die Löslichkeit von SiÖ2 zunimmt und die von AI2O3 eine Verminderung erfährt. Basierend auf dem so exemplarisch erbrachten Nachweis für die Verstärkung der schädigenden AKR durch das Tausalz wird die Notwendigkeit und Richtigkeit der Durchführung von AKR-Betonversuchen mit Alkalizufuhr im ARS 04/2013 zur zukünftigen Vermeidung von AKR-Schäden an Betonfahrbahndecken im Rahmen von Neubau- und Erneuerungsmaßnahmen im Bundesfernstraßennetz belegt. Zusätzlich durchgeführte WS-Grundprüfungen nach dem ARS 04/2013 mit den beiden Gesteinskörnungen der Löse versuche veranschaulichen, dass die nach der Alkali-
Richtlinie des DAfStb als unbedenklich eingestuften Gesteinskörnungen bei den Betonversuchen mit Alkalizufuhr durchaus als alkaliempfindlich bewertet werden können. Dies wiederum führt zu einer Verminderung der für den Betonstraßenbau verfügbaren Gesteinskörnungen.
Vor diesem Hintergrund wird nach neuartigen AKR-Vermeidungsstrategien gesucht, die auch eine Verwendung der als grenzwertig alkaliempfindlich eingestuften Gesteinskörnungen erlaubt.
Einen möglichen Lösungsansatz stellt in diesem Kontext die Innenhydrophobierung des Fahrbahndeckenbetons dar. Es soll so durch die Behinderung des Feuchte- und Tausalzeintrags in den Beton der AKR-Schädigungsprozess signifikant vermindert werden. Für die Bewertung der Leistungsfähigkeit der Innenhydrophobierung zur Vermeidung bzw. Verminderung einer schädigenden AKR in Betonfahrbahndecken wird zurzeit im Aufträge der BASt an der BAM ein Forschungsvorhaben bearbeitet. Im Rahmen dieses Beitrags werden erste Ergebnisse dieses Projekts vorgestellt. So wird exemplarisch an einem Oberbeton (D > 8)/Unterbeton und einem Oberbeton 0/8 mit einer alkaliempfindlichen Gesteinskörnung der Einfluss zweier Hydrophobierungsmittel auf die Frisch- und Festbetoneigenschaften ganzheitlich aufgezeigt und bewertet. Bei Letzteren stehen zunächst die mechanischen und hygrischen Parameter sowie der Frost-Tausalzwiderstand im Vordergrund. In einem weiteren Schritt wird der Einfluss beider Hydrophobierungsmittel auf die schädigende AKR mittels AKR-Betonversuchen mit Alkalizufuhr beleuchtet. Dabei gelangen ergänzend zur Beurteilung des Tausalzeintrags die Laser-Induced Breakdown Spectroscopy (LIBS) und zur Bewertung der Ausprägung der AKR und sekundären Ettringitbildung (SEB) die Dünnschliffmikroskopie zum Einsatz.
AKR an Betonfahrbahndecken – ausgewählte Einflussgrößen und neuartige AKR-Vermeidungsstrategie
(2019)
In den letzten Jahren sind im deutschen Bundesautobahnnetz vermehrt Schäden an vor 2005 hergestellten Betonfahrbahndecken aufgetreten, die mit einer Alkali-Kieselsäure-Reaktion (AKR) in Verbindung gebracht werden. Vor diesem Hintergrund werden in diesem Beitrag zunächst die Voraussetzungen und ausgewählte Einflussgrößen für eine schädigende AKR aufgezeigt. Besondere Aufmerksamkeit wird dabei der Rolle des Tausalzeintrags durch den Winterdienst bei Betonfahrbahndecken geschenkt. So wird mit Löseversuchen in 1 M KOH-Lösung zweier Gesteinskörnungen bei 80 °C gezeigt, dass mit zunehmender NaCl-Zugabe die Löslichkeit von SiO2 zunimmt und die von Al2O3 eine Verminderung erfährt. Basierend auf dem so exemplarisch erbrachten Nachweis für die Verstärkung der schädigenden AKR durch das Tausalz wird die Notwendigkeit und Richtigkeit der Durchführung von AKR-Betonversuchen mit Alkalizufuhr im ARS 04/2013 zur zukünftigen Vermeidung von AKR-Schäden an Betonfahrbahndecken im Rahmen von Neubau- und Erneuerungsmaßnahmen im Bundesfernstraßennetz belegt. Zusätzlich durchgeführte WS-Grundprüfungen nach dem ARS 04/2013 mit den beiden Gesteinskörnungen der Löseversuche veranschaulichen, dass die nach der Alkali-Richtlinie des DAfStb als unbedenklich eingestuften Gesteinskörnungen bei den Betonversuchen mit Alkalizufuhr durchaus als alkaliempfindlich bewertet werden können. Dies wiederum führt zu einer Verminderung der für den Betonstraßenbau verfügba-ren Gesteinskörnungen. Vor diesem Hintergrund wird nach neuartigen AKR-Vermeidungsstrategien gesucht, die auch eine Verwendung der als grenzwertig alkaliemp-findlich eingestuften Gesteinskörnungen erlaubt. Einen möglichen Lösungsansatz stellt in diesem Kontext die Innenhydrophobierung des Fahrbahndeckenbetons dar. Es soll so durch die Behinderung des Feuchte- und Tausalzeintrags in den Beton der AKR-Schädigungsprozess signifikant vermindert werden. Für die Bewertung der Leistungsfähigkeit der Innenhydrophobierung zur Vermeidung bzw. Verminderung einer schädigenden AKR in Betonfahrbahndecken wird zurzeit im Auftrage der BASt an der BAM ein Forschungsvorha-ben bearbeitet. Im Rahmen dieses Beitrags werden erste Ergebnisse dieses Projekts vorge-stellt. So wird exemplarisch an einem Oberbeton (D > 8)/Unterbeton und einem Oberbeton 0/8 mit einer alkaliempfindlichen Gesteinskörnung der Einfluss zweier Hydrophobierungsmit-tel auf die Frisch- und Festbetoneigenschaften ganzheitlich aufgezeigt und bewertet. Bei Letz-teren stehen zunächst die mechanischen und hygrischen Parameter sowie der Frost-Tausalzwiderstand im Vordergrund. In einem weiteren Schritt wird der Einfluss beider Hydro-phobierungsmittel auf die schädigende AKR mittels AKR-Betonversuchen mit Alkalizufuhr beleuchtet. Dabei gelangen ergänzend zur Beurteilung des Tausalzeintrags die Laser-Induced Breakdown Spectroscopy (LIBS) und zur Bewertung der Ausprägung der AKR und sekundä-ren Ettringitbildung (SEB) die Dünnschliffmikroskopie zum Einsatz.
In Deutschland fallen jährlich 20 Millionen Tonnen Altpapier an. 75 % davon werden dem Recyclingprozess zugeführt. Dabei bleiben Prozessrückstände wie Deinkingschlämme, Sortierrückstände und Faserreststoffe übrig. Zusammengefasst als Papierschlamm verwerten die Recycler diesen Reststoff thermisch in dezentralen Heizkraftwerken. Die dabei anfallende Papierasche hat mit den Anteilen der Hauptoxide von 59 M.-% CaO, 22 M.-% SiO2 und 13 M.-% Al2O3 eine ähnliche chemische Zusammensetzung wie Portlandzement, wobei sich die Mineralphasen unterscheiden. Durch eine Aktivierung der Papierasche können jedoch hydraulisch aktive Phasen wie Mayenit (C7A12) und Belit (C2S) erzeugt werden. Die Mineralphase Mayenit reagiert schnell mit Wasser zu Calciumaluminathydraten, wodurch der Bindemittelleim schnell ansteift. Die festigkeitsbildenden Calciumsilicathydrate (CSH) in Bindemittelleimen entstehen bei einer späteren Reaktion von Belit mit Wasser.
Zur Aktivierung dient eine hydrothermale Calcinierung. Dabei wird Papierasche mit einer Aktivatorlösung (Wasser oder KOH) gemischt und bei 200 °C hydrothermal behandelt, wobei sich Hydratphasen ausbilden. Diese Zwischenprodukte dehydratisieren durch eine anschließende Calcinierung zu reaktiven Calciumsilicaten und Calciumaluminaten. Wie sich die Parameter des Aktivierungsprozesses auf die Mineralphasen auswirken, war Fokus der Untersuchungen. Mit thermogravimetrischen Analysen der Zwischenprodukte konnten die Reaktionsprodukte nach dem hydrothermalen Prozessschritt bestimmt werden. Den größten Einfluss auf den Mineralphasenbestand hat hierbei die Alkalität der Aktivatorlösung. Im zweiten Prozessschritt, der Calcinierung, ist die Temperatur der wesentliche Faktor für die Ausbildung reaktiver Phasen. Die Ergebnisse kalorimetrischer Untersuchungen an Leimen aus den calcinierten Proben dienten der Auswahl der optimalen Calcinierungstemperatur. Die gesamte Reaktionswärme war für die Proben, welche bei einer Calcinierungstemperatur zwischen 700-800 °C hergestellt wurden, am höchsten.
Die Strukturierung keramischer Grünfolien und Laminate ist ein wesentlicher Prozessschritt in der keramischen Multilayer-Technologie und begründet die funktionelle Vielfalt keramischer Multilayer. Benötigt wird die Grünbearbeitung für die Herstellung elektrischer und thermischer Vias sowie innerer Kavitäten und Kanäle für Transport und Lagerung von Gasen und Flüssigkeiten in hochintegrierten Schaltungsträgern, Sensoren und Reaktoren. Standardverfahren in der industriellen Fertigung sind Heißschneiden, Stanzen und Laserbearbeitung. Darüber hinaus werden auch Bohren, Fräsen, Sägen und Heißprägen verwendet. Über die Erprobung weiterer Verfahren wie Wasserstrahlschneiden, Dampfstrahlätzen und Powder Blasting wird in der Literatur berichtet.
Im Vortrag werden spezifische Vor- und Nachteile der eingesetzten Verfahren beleuchtet. Abschließend werden die Kriterien für die Auswahl des optimalen Strukturierungsverfahrens diskutiert. Zusammensetzung und Gefüge sowie die dadurch bedingten mechanischen und thermomechanischen Eigenschaften sowie das Absorptionsverhalten von Grünfolien sind sehr unterschiedlich. Daraus resultieren unterschiedliche optimale Bearbeitbarkeitsparameter.
The full-notch creep test (FNCT) is a common method to evaluate the environmental stress cracking (ESC) behavior of high-density polyethylene (PE-HD) container materials . The test procedure as specified in ISO 16770 provides a comparative measure of the resistance against ESC using the time to failure of specimens mechanically loaded in a well-defined liquid environment. Since the craze-crack damage mechanism underlying the ESC process is associated with brittle failure, the occurrence of globally brittle fracture surfaces is a prerequisite to consider an FNCT measurement as representative for ESC . Therefore, an optical evaluation of FNCT fracture surfaces concerning their brittleness is essential. Due to the experimental setup, an inevitable increase of the true mechanical stress and the associated appearance of small ductile parts on fracture surfaces is induced in any case. Hence, an FNCT experiment is considered as 'valid', if the corresponding fracture surface is predominantly brittle . Based on laser scanning microscopy (LSM) height data of FNCT fracture surfaces , a universal and easy-to-use phenomenological criterion was developed to assess the validity of distinct FNCT experiments. This criterion is supposed to facilitate a quick evaluation of FNCT results in practical routine testing.
Composite-Druckbehälter werden für Speicherung und Transport von Gasen unter hohem Druck verwendet. Durch die gewichtssparende Struktur, die aus einem dünnwandigem Metallgefäß und Faserverbundwerkstoff-Ummantelung besteht, sind solche Behälter insbesondere für die Luftfahrt- und Automobilindustrie interessant, z.B. als Wasserstoffspeicher.
Die Druckprüfung ist ein konventioneller Test, um die Integrität von Metalldruckbehältern zu bewerten. Im Falle des Composite-Druckbehälters könnte eine solche Prüfung jedoch den Faserverbundwerkstoff überbeanspruchen und somit die verbleibende Lebensdauer der getesteten Komponente verringern. Infolgedessen ist es notwendig, Verfahren zur zerstörungsfreien Prüfung und möglicherweise zur Zustandsüberwachung von Composite-Druckbehältern zu entwickeln. Unser Ansatz verwendet geführte Ultraschallwellen und hat das Potenzial, kritische Schäden wie Risse im Metall und Faserbrüche und Matrixrisse in Faserverbundwerkstoff zu detektieren.
In diesem Beitrag wurde die Scaled Boundary Finite Elemente Methode benutzt, um die multimodale, geführte Wellenausbreitung in einem Mehrschichtverbund, der aus Metall und Kohlenfaserverbund entsteht, zu analysieren. Das Verfahren ermöglicht die Identifizierung geeigneter Wellenmoden und die Analyse ihrer Interaktion mit verschiedenen Schäden. Diese Kenntnisse sollen für die Entwicklung von Verfahren zur Zustandsüberwachung von Composite-Druckbehältern angewendet werden.
Die Kenntnis von Materialeigenschaften spielt bei der Entwicklung oder Optimierung von
Betonen und Bauweisen für den Straßenbau sowie der Qualitätskontrolle und -sicherung eine bedeutende Rolle. Gleichermaßen bilden physikalische Materialkennwerte die Grundlage für die rechnerische Dimensionierung und die Restsubstanzbewertung von Betonfahrbahndecken.
Einen relevanten Kennwert bei der Untersuchung thermisch induzierter Spannungsund Verformungszustände stellt der thermische Ausdehnungskoeffizient von Beton dar.
Dieser beeinflusst beispielsweise maßgeblich das Längsdehnungsverhalten des Deckensystems sowie das Ausmaß von Plattenkrümmungen und Fugenbewegungen. Im Zuge der systematischen Weiterentwicklung der rechnerischen Dimensionierung aber auch im Zusammenhang mit der gezielten Verbesserung der Gebrauchseigenschaften von Fahrbahndecken gilt es zu hinterfragen, ob lastunabhängige Formänderungseigenschaften, wie z. B. der thermische Ausdehnungskoeffizient der verwendeten Betone, aktuell ausreichend Beachtung finden, ob allgemeine Literaturwerte für die heutigen Fahrbandeckenbetone stets Gültigkeit besitzen und ob deren Implementierung in moderne Rechenmodelle zu validen Ergebnissen führt. Für eine empirische Herangehensweise ist die Verfügbarkeit adäquater Prüfverfahren von entscheidender Bedeutung. In Deutschland existiert aktuell jedoch kein standardisiertes oder genormtes Verfahren für die prüftechnische Bestimmung des thermischen Ausdehnungskoeffizienten von Beton. Daher wurden unter Beachtung straßenbauspezifischer Gesichtspunkte zwei Prüfansätze entwickelt, die in diesem Beitrag vorgestellt und hinsichtlich möglicher Messunsicherheiten und Messungenauigkeiten diskutiert werden.
Außerdem erfolgt die Darstellung ausgewählter Ergebnisse aus Analysen an Bestandsbetonen aus dem BAB-Netz. Im Ergebnis sollen die Untersuchungen einen Beitrag zur Schaffung der prüftechnischen Voraussetzungen für eine abgesicherte Quantifzierung der thermischen Dehnung von Fahrbahndeckenbetonen leisten.
Solidification cracking of metals is a well-researched topic in the field of welding science. A material’s susceptibility to solidification cracking can be tested using numerous different specialized test procedures, one of which is the Modified Varestraint-/Transvarestraint test (MVT). It was developed at BAM in 1982 and is internationally standardised. Over the decades, this test has been extensively used to characterise the solidification cracking resistance of many different materials.
The present study was conducted to further investigate the influences of the standardised MVT testing parameters, as well as the characteristics of evaluation methods on the results. Several different high alloyed martensitic LTT (low transformation temperature) filler materials, CrNi and CrMn type, were used. In previous pilot studies, these alloys have shown a rather distinctive solidification cracking behaviour (Fig. 1). During testing, energy input per unit length and bending speed were varied (especially the latter is usually kept at standard values), in addition to the most commonly altered factor - total deformation.
First, the effects of different process parameter sets on the solidification cracking response were measured using the standard approach - microscopic analysis of the specimen surface. It was found that not all parameter changes had the expected outcome. For the Cr8Ni6 and Cr11Mn5 filler materials, influences of energy input per unit length and welding speed were in direct opposition.
In order to investigate those apparent contradictions, µCT scans of MVT specimens were made. The results consistently show sub surface cracking, to significant, yet varying extents. Different primary solidification types were found using WDX-analysis, an aspect that is believed to be the main difference between the CrNi- and CrMn-type materials and their cracking characteristics.
Results show that when it comes to testing of modern high-performance alloys, one set of standard MVT testing parameters might not be equally suitable for all materials. Also, to properly accommodate different solidification types, sub-surface cracking has to be taken into account.
Porous materials play an important role in several fields of technology, especially for energy applications like photovoltaics, electrolysis or batteries. The activity of porous films is affected by properties like porosity, film thickness, chemical composition of the material as well as the crystallinity of the framework. The complex morphology of such porous films constitutes a challenge even for modern analytical techniques and requires new approaches employing the combination/complementation of data of different analytical methods. In this contribution we characterize thin mesoporous iridium-titanium mixed oxide film properties by Electron Probe Microanalysis (EPMA) with energy dispersive X-ray spectroscopy (EDS) at an SEM.
Porous materials play an important role in several fields of technology, especially for energy applications like photovoltaics, electrolysis or batteries. The activity of porous films is affected by properties like porosity, film thickness, chemical composition of the material as well as the crystallinity of the framework. The complex morphology of such porous films constitutes a challenge even for modern analytical techniques and requires new approaches employing the combination/complementation of data of different analytical methods. In this contribution we characterize thin mesoporous iridium-titanium mixed oxide film properties by Electron Probe Microanalysis (EPMA) with energy dispersive X-ray spectroscopy (EDS) at an SEM.
Porous materials play an important role in several fields of technology, especially for energy applications like photovoltaics, electrolysis or batteries. The activity of porous films is affected by properties like porosity, film thickness, chemical composition of the material as well as the crystallinity of the framework. The complex morphology of such porous films constitutes a challenge even for modern analytical techniques and requires new approaches employing the combination/complementation of data of different analytical methods. In this contribution we characterize thin mesoporous iridium-titanium mixed oxide film properties by Electron Probe Microanalysis (EPMA) with energy dispersive X-ray spectroscopy (EDS) at an SEM.
Analysis of elemental composition of Fe1-xNix and Si1-xGex alloy thin films by EPMA and µ-XRF
(2019)
The present study reports on measurements on thin Fe-Ni films on silicon and first-time results of analysis on Si-Ge thin films deposited on a non-conductive aluminium oxide Substrate by electron probe microanalysis (EPMA). Standard-based and standardless EPMA (with EDS) results were used in combination with the thin film analysis software Stratagem for the quantification.
Further, X-ray fluorescence analysis (XRF) can be used for the determination of elemental composition and thickness of such films as well. In this case, XRF with a μ-focus X-ray source (μ-XRF) attached to a SEM was applied. For quantification, a fundamental parameter (FP) approach has been used to calculate standard-based and standardless results.
Both thin film systems have been chosen as samples of an international round robin test (RRT) organised in the frame of standardisation technical committee ISO/TC 201 ‘Surface chemical analysis’, under the lead of KRISS. The main objective of the RRT is to compare the results of atomic fractions of Fe1-xNix and Si1-xGex alloy films obtained by different surface Analysis techniques, such as X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and secondary ion mass spectrometry (SIMS) applied in the depth-profiling operation mode.
Five samples of different atomic fractions of each thin film system, i.e., Fe1-xNix and Si1-xGex, have been grown by ion beam sputter deposition on silicon and Al2O3 wafers, respectively. Reference FeNi and SiGe films with well-known elemental composition and thickness have been also supplied for standard-based analysis. An excellent agreement has been obtained between the atomic fractions determined by EPMA and µ-XRF with the KRISS certified values.
Lamb waves are widely used for non-destructive evaluation of material parameters as well as for detection of defects. Another application of Lamb waves is quality control of adhesive joints.
Researchers are currently investigating shear horizontal and zero-group velocity modes for characterisation of the adhesive bonding strength. In a new approach, Lamb wave mode repulsion is used to obtain the coupling strength between different layers to characterise the adhesive bonding strength. The modes of the individual layers become coupled in the multilayered systems forming particular regions, the so-called mode repulsion regions. This study investigates these modes and their interaction in two-layered plate-like structures with varying coupling strength both numerically, with the Scaled Boundary FEM, and experimentally.
Lamb waves are widely used for non-destructive evaluation of material parameters as well as for detection of defects. Another application of Lamb waves is quality control of adhesive joints.
Researchers are currently investigating shear horizontal and zero-group velocity modes for characterisation of the adhesive bonding strength. In a new approach, Lamb wave mode repulsion is used to obtain the coupling strength between different layers to characterise the adhesive bonding strength. The modes of the individual layers become coupled in the multilayered systems forming particular regions, the so-called mode repulsion regions. This study investigates these modes and their interaction in two-layered plate-like structures with varying coupling strength both numerically, with the Scaled Boundary FEM, and experimentally
Due to the favorable properties of polymers, their production and thus their input into the environment has increased significantly in recent decades. Currently, FTIR or Raman spectroscopy are mainly applied for the analysis of microplastic particles (MP) in environmental samples. However, these methods have great difficulties in determining metrologically traceable MP values, especially with regard to the limiting values, as preferred in regulation. Therefore, we developed a systematic and fast thermoanalytical method called TED-GC-MS (thermal extraction desorption gas chromatography mass spectrometry), which determines mass contents. Now the current goal is the determination of its process parameters.
This poster illustrates the theoretical requirements for MP analysis (left side) and contrast them with the current state of research (right side).Unexpected practical problems are presented and the relatively new method is discussed concerning the quality requirements of well-established methods such as LC-or GC-MS.
Determining a suitable and reliable end-of-lifetime criterion for O-ring seals is an important issue for long-term seal applications. Therefore, seal failure of ethylene propylene diene rubber (EPDM) and hydrogenated nitrile butadiene rubber (HNBR) O-rings aged in the compressed state at 125 °C and at 150 °C for up to 1.5 years was analyzed and investigated under static conditions, using both non-lubricated and lubricated seals. Changes of the material properties were analyzed with dynamic-mechanical analysis and permeability experiments. Indenter modulus measurements were used to investigate DLO effects. It became clear that O-rings can remain leak-tight under static conditions even when material properties have already degraded considerably, especially when adhesion effects are encountered. As a feasible and reliable end-of-lifetime criterion for O-ring seals under static conditions should include a safety margin for slight dimensional changes, a modified leakage test involving a small and rapid partial decompression of the seal was introduced that enabled determining a more realistic but still conservative end-of-lifetime criterion for an EPDM seal.
Polyether and -ester urethanes (PU) were exposed to artificial weathering at 40 °C and artificial UV radiation in a weathering chamber. In 3 parallel exposures, humidity was varied between dry, humid, and wet conditions. Material alteration was investigated by various analytical techniques like size exclusion chromatography
(SEC), liquid chromatography-infrared spectroscopy (LC-FTIR), thermal-desorption gas chromatography-mass spectrometry (TD-GC-MS), fluorescence mapping and dynamic mechanical analysis (DMA). Our results show that depending on the weathering conditions, different degradation effects can be observed. By means of SEC an initial strong decrease of the molar masses and a broadening of the mass distributions was found. After a material dependent time span this was followed by a plateau where molar mass changes were less significant. A minor moisture-dependent degradation effect was only found for polyester PU. Fluorescence measurements on two materials revealed an increase in the luminescence intensity upon weathering process reaching a saturation level after about 500 h. The changes in the optical properties observed after different exposure conditions and times were very similar. The TD-GC-MS data showed the fate of the stabilizers and antioxidant in the course of weathering. LC-FTIR measurements revealed a change in peak intensities and the ratio of urethane and carbonyl bands.
Die zunehmenden Nachweise von Kunststoffen in verschiedenen Umweltmedien erfahren in den letzten Jahren weltweit ein zunehmendes wissenschaftliches, gesellschaftliches und politisches Interesse. Besondere Aufmerksamkeit erfahren Kunststoffpartikel von 1-1.000 µm sogenanntes Mikroplastik. Es wurde mittlerweile in Wasser, Böden, Luft und Biota nachgewiesen. Obwohl die Wirkungen auf die natürlichen Umweltfunktionen noch unklar sind und kontrovers diskutiert werden, ist allein durch die ubiquitäre Präsenz eine systematische Erfassung von Eintragsquellen und Verbleib der Partikel über alle Umweltmedien notwendig, um Maßnahmen zur Reduktion der Einträge zu veranlassen.
Für eine zuverlässige Erfassung sind medienübergreifende Verfahren zu entwickeln, welche die drei analytischen Schritte, Probennahme, Probenaufbereitung und Detektion beinhalten. Die Verfahren adressieren unterschiedliche Zielgruppen, welche verschiedene analytische Informationen fordern. Für die akademische Bewertung werden Verfahren mit hohem analytischen Aufwand favorisiert, welche möglichst detaillierte Information über Partikelsorte, -größe, -zahl und -oberflächenbeschaffenheit geben. Im Gegensatz dazu, fordern Anwender aus der Praxis schnelle und einfache Monitoring Verfahren, welche die Bestimmung eines Massengehaltes, bzw. eines Grenzwertes zulassen. Allen ist gemeinsam, dass ein hoher interdisziplinärer Anspruch besteht, der sowohl technische Voraussetzungen zur repräsentativen Probennahme und die Limitationen von Detektionsverfahren berücksichtigt, als auch die Fachkompetenz von Biologen, Umweltwissenschaften, Analytiker und Polymerwissenschaftler einschließt.
Verfahren zum Mikroplastiknachweis müssen auch verschieden Proben mit sehr unterschiedlichen Gehalten an natürlicher Matrix gerecht werden. So müssen allein für Wasser Verfahren entwickelt werden, die Mikroplastik verschiedener Form (sphärische Partikel, komplexe Bruchstücke, Fasern) aus Medien mit sehr variablen Partikelanteil (u.a. Trinkwasser, Oberflächenwasser, Abwasser) repräsentativ erfassen sowie schnell und kostengünstig sind – einschließlich der notwendigen Probenaufbereitung. Die jeweiligen Detektionsverfahren müssen z.B. einzelne Partikel oder integrale Gehalte über drei Dekadenklassen für thermoplastische und insbesondere auch elastomere Partikelsorten erfassen können.
Es besteht die grundsätzliche Anforderung, dass alle nichtmetallischen und metallischen Materialien nur dann in Sauerstoffanwendungen eingesetzt werden dürfen, wenn sie sicherheitstechnisch auch für die entsprechenden Betriebsbedingungen geeignet sind. Der Vortrag stellt nicht nur die gängigen Prüfverfahren und Beurteilungskriterien. Es werden auch die folgenden Fragen beantwortet, die häufig von Wirtschaftsunternehmen und Verbänden gestellt werden:
- Welchen praktischen Anwendungsfall bilden die Prüfungen ab?
- Welche Untersuchungsmethoden führt die BAM durch?
- Warum verwendet die BAM ergänzende Beurteilungskriterien bei der sicherheitstechnischen Interpretation von Prüfergebnissen?
- Warum empfiehlt die BAM chargenbezogene Materialprüfungen?
- Worin unterscheiden sich die zwei von der BAM verwendeten Methoden zur Beurteilung der Ausbrennsicherheit von Armaturen und Anlagenteilen und welche Vor- und Nachteile bietet jede dieser Methoden?
The antibacterial features of natural pine/spruce rosin are well established, yet the functionality in various thermoplastics has not been surveyed. This work focuses on the processing of industrial grade purified rosin mixed with polyethylene (PE), polypropylene (PP), polylactic acid (PLA), polyamide (PA) and corn starch based biopolymer (CS). Homopolymer masterbatches were extrusion-compounded and melt-spun to form fibres for a wide range of products, such as filters, reinforcements, clothing and medical textiles. Due to the versatile chemical structure of rosin, it was observed compatible with all the selected polymers. In general, the rosin-blended systems were shear-thinning in a molten condition. The doped fibres spun of PE and PP indicated adequate melt-spinning capability and proper mechanical properties in terms of ultimate strength and Young's modulus. The antibacterial response was found dependent on the selected polymer. Especially PE with a 10 wt% rosin content showed significant antibacterial effects against Escherichia coli DH5α and Staphylococcus aureus ATCC 12598 when analysed in the Ringer's solution for 24 h.
In einer Vielzahl technischer Anwendungen spielt die Aufrechterhaltung eines definierten Reibungs- und Verschleißverhaltens zwischen bewegten Oberflächen für die Sicherheit und Funktionalität eine ent-scheidende Rolle. Die Oberflächentechnik versucht durch geeignete Verfahren die Randschichten zu ertüchtigen, um Reibung und Verschleiß zu kontrollieren. Eine Verbesserung der Materialeigenschaften kann durch flächige Beschichtungen erreicht werden. Zusätzlich ermöglichen Oberflächenstrukturierun-gen breite Möglichkeiten zur Beeinflussung des Schmierungszustandes bzw. der Kontaktbedingungen. Neben Negativstrukturen bieten ebenfalls erhabene Mikrostrukturen großes Potenzial zur Beeinflussung des tribologischen Verhaltens. Ihr Einsatz ist aber aufgrund der besonderen Verschleißproblematik er-habener Strukturen momentan limitiert, so dass in der Regel zusätzliche verschleißreduzierende Be-schichtungen notwendig werden.
In diesem Beitrag wurde das Verfahren der Laserimplantation angewandt, mit dem erhabene und sepa-rierte Oberflächenstrukturen hoher Verschleißfestigkeit in einem Fertigungsschritt erzeugbar sind. Das Verfahren basiert auf einem lokalisierten Dispergieren von Hartstoffpartikeln. Hierfür wurde erstmalig ein gepulster Faserlaser mit hoher Strahlqualität zur Erzeugung punkt- und linienförmiger Mikrostrukturen angewandt. Versuche wurden auf dem Kaltarbeitsstahl X153CrMoV12 unter Anwendung von Titandibo-rid als Hartstoff durchgeführt. Anhand von Härtemessungen konnte gezeigt werden, dass sowohl punkt- als auch linienförmige Strukturen mit Härten über 1000 HV1 und einer feinkörnigen Mikrostruktur mit feinverteilten Hartstoffpartikeln herstellbar sind. Des Weiteren war es möglich, die Implantgeometrien, welche an Querschliffen und durch Weißlichtinterferometeraufnahmen erfasst wurden, durch die Puls-leistung und Pulsdauer zu steuern.
In diesem Vortrag wird am Beispiel magnetischer Werkstoffe zur Energiewandlung gezeigt, wie röntgentomographische Untersuchungen zur Strukturaufklärung in Kompositen und Massivproben beitragen können. Die Bauteile werden zerstörungsfrei geprüft, um Risse, Poren und andere Defekte und ihren Einfluss auf die funktionellen Eigenschaften dreidimensional und rechtzeitig im Lebenszyklus des Werkstoffs zu charakterisieren. Kombiniert man Mikrotomographie mit anderen Methoden der magnetischen Werkstoffcharakterisierung, lassen sich einzigartige Aussagen über den Aufbau und die funktionellen Eigenschaften treffen.
The performance of functional coatings and adhesively joined hybrid components relies strongly on the stability of the polymer-metal interface. With the increasing utilization of multi-material structures in the automotive and aerospace industry, it is of great scientific and technical interest to understand the processes leading to interface degradation and to develop novel strategies to increase corrosion and delamination resistance.
The aim of this project is to develop thin epoxy-based films and their carbon nanofiller loaded composites on aluminium alloy AA2024-T3 as a model system and to investigate their interfacial stability under corrosive and coupled corrosive-mechanical load. Spin coating was used for the layer-by-layer deposition of poly[(o-cresyl glycidyl ether)-co-formaldehyde] and poly-(ethylenimine) bi-layers. Atomic force microscopy (AFM) results indicate a very homogeneous and dense film with low surface roughness. Carbon nanofillers were introduced either by mixing into the coating components or in between individual layers to control the separation between the carbon nanofillers and alloy surface. The film chemistry and barrier properties were characterized by means of spectroscopic and electrochemical methods, respectively. The degradation and delamination behavior of the epoxy-based films was characterized by means of in situ AFM corrosion experiments. The quantitative imaging (QI) mode allowed the observation of hydrogen-generation induced blister formation during exposure to corrosive electrolyte and how the local corrosion processes evolved with exposure time. Complementary energy dispersive X-ray spectroscopy (EDX) analysis was performed to correlate the corrosion behavior with the different intermetallic particle chemistries and distributions. The presentation will summarize our results on the effect of interface chemistry and carbon nanofiller – alloy separation on the initiation of local corrosion processes on thin film covered AA2024-T3 aluminium alloys.
The 3D microstructure of an Al alloy matrix composite with two ceramic reinforcements was investigated by synchrotron X-ray tomography. A deep learning algorithm was used for the segmentation of four different phases. We show that convolutional networks with the U-Net architecture are able to solve complex segmentation tasks with small amount of training data.
Low-velocity impact damages were monitored in-situ using an infrared camera before, during and after Impact load. Thermal images were recorded as a function of time at the front side (impact) as well as at the rear side of the plates using a high frame rate. In CFRP and GFRP specimens with different thicknesses and made of various types of fibers and matrix materials, different kind of damages were observed. The sizes of the heated areas being related to the damages and the amount of energy dissipated into heat was determined quantitatively as a function of impact energy and are a measure of the resistance of the different materials against impact load.
Applications on Surface Functionalization by Laser-Induced Periodic Surface Structures (LIPSS)
(2019)
In recent years, the understanding on the formation of laser-induced periodic surface structures (LIPSS) has led to an emerging variety of applications that modify the optical, mechanical and chemical properties of many materials. Such structures strongly depend on the used polarization and are formed usually after irradiation with ultrashort linearly polarized laser pulses. Some specific formation mechanisms to explain every situation are still to be uncovered, but the most accepted explanation relies on the interference of the incident laser beam with electromagnetic surface waves that propagate or scatter at the surface of the irradiated materials. This leads to an intensity modulation that is finally responsible for the selective ablation in the form of parallel structures with periodicities ranging from hundreds of nanometers up to some micrometers. The versatility when forming such structures is based on the high reproducibility with different wavelength, pulse duration and repetition rate laser sources, customized micro- and nanometric spatial resolutions and compatibility with industrially relevant processing speeds when combined with fast scanning devices. In this contribution, we review the latest applications in the rapidly emerging field of surface functionalization through LIPSS, including biomimetic functionalities on fluid transport, control of the wetting properties, specific optical responses in technical materials, improvement of tribological performance on metallic surfaces and bacterial and cell growth for medical devices among many others.
The applicability of 1D-quadrupole-model on the depth estimation of overload-induced delaminations is tested in this contribution. While classical 1D-methods like Pulsed Phase Transformation and Thermographic Signal Reconstruction determine the depth of a defect by one parameter, a two-layer quadrupole model provides two parameters: depth and thermal resistance. In addition, the convectional losses at the surfaces may be considered. The defect investigated is a large-scale delamination in glass fibre reinforced polymer generated by tension overload.
A discussion is provided on demands that must be met in order to apply fracture mechanics to the determination of overall fatigue lifetime and strength, i.e., S-N curves and fatigue limits. These comprise the determination of the cyclic crack driving force for all stages of fatigue crack propagation, in particular for the short crack stage where the crack driving force has to be determined for elastic-plastic deformation and the gradual build-up of the crack closure phenomenon. Special emphasis is put on a fatigue damage relevant specification of the initial crack size. Different approaches in the literature are discussed. Another important aspect is the adequate treatment of multiple crack propagation. Finally, the discussion is illustrated by an example of a butt weld made of a medium strength steel.
A numerical framework for simulation of the steady-state thermal behaviour in keyhole mode welding has been developed. It is based on the equivalent heat source concept and consists of two parts: computational thermo-fluid dynamics and heat conduction. The solution of the thermo-fluid dynamics problem by the finite element method for a bounded domain results in a weld pool interface geometry being the input data for a subsequent heat conduction problem solved for a workpiece by a proposed boundary element method. The main physical phenomena, such as keyhole shape, thermo-capillary and natural convection and temperature-dependent material properties are taken into consideration. The developed technique is applied to complete-penetration keyhole laser beam welding of a 15 mm thick low-alloyed steel plate at a welding speed of 33 mm/s and a laser power of 18 kW. The fluid flow of the molten metal has a strong influence on the weld pool geometry. The thermo-capillary convection is responsible for an increase of the weld pool size near the plate surfaces and a bulge formation near the plate middle plane. The numerical and experimental molten pools, cross-sectional weld dimensions and thermal cycles of the heat affected zone are in close agreement.
A numerical framework simulation of the steady-state thermal behaviour in keyhole mode welding has been developed. It is based on the equivalent heat source concept and consists of two parts: computational thermo-fluid dynamics and heat conduction. The solution of the thermo-fluid dynamics problem by the finite element method for a bounded domain results in a weld pool interface geometry being the input data for a subsequent heat conduction problem solved for a workpiece by proposed boundary element method. The main physical phenomena, such as keyhole shape, thermo-capillary and natural convection and temperaturedependent material properties are taken into consideration. The developed technique is applied to complete-penetration keyhole laser beam welding of a 15 mm thick low-alloyed steel plate at a welding speed of 33 mm/s and a laser power of 18 kW. The fluid flow of the molten metal has a strong influence on the weld pool geometry. The thermo-capillary convection is responsible for an increase of the weld pool size near the plate surfaces and a bulge formation near the plate middle plane. The numerical and experimental molten pools, cross-sectional weld dimensions and thermal cycles of the heat affected zone are in close agreement.
Heating oil storage tanks made of polyethylene grades have been on the market in Germany since the early 1970s. To ensure safety, their replacement is recommended by tank manufacturers after a period of 30 years. Polyethylene is subject to ageing by alteration of the properties during its life cycle. The degree of degradation and the nature of the process mainly depend on the chemical alteration of the polyethylene, the wall thickness of the tank and the environmental conditions. There are no data available on the long-term behaviour of the polyethylene grades, especially after a service life of more than 30 years.
The aim of this investigation was to find a suitable test method to determine the factual degree of damage in comparison to the uncontaminated polyethylene grades. Material data of the used polyethylene grades are available because the BAM was the competent authority for the tests and expert reports for the approval of these tanks until the middle of the 1990s. Therefore, tank sections from the bottom, the shell and the roof of 22 individual storage tanks produced of polyethylene grades A and B have been examined by Melt Flow Rate (MFR) and Attenuated Total Reflectance (ATR). Their service life was in the range between 20 and 41 years.
The MFR measurements of the tank sections showed differences in the values depending on the weight which was used (5 kg or 21.6 kg). An increase of the MFR was determined for the samples of polyethylene grade A, whereas a reduction of the MFR values was measured for most samples of polyethylene grade B. This grade is mainly subject to the internal ageing by cross-linkages, increased degree of branched molecules and loss of the plasticizer.
ATR analysis exhibits an absorption band at 909 cm‒1 predominantly in samples of polyethylene grade A indicating chain scission and concomitantly formed terminal vinyl groups. This absorption band can be used for the characterization of the ageing of the polyethylene grades.
Auf dem Weg zu Industrie 4.0: Bestimmung von Messunsicherheitsbudgets in der Oberflächentechnik
(2019)
Vorgestellt wurde die Bestimmung von Messunsicherheitsbudgets für sehr unterschiedliche physikalische Größen, die in der Oberflächentechnik von hoher Relevanz sind: Stufenhöhe h, Schichtdicke d, Eindringhärte HIT und Haftfestigkeit. Die Unterschiede betreffen die Art der Prüfmethodik (optisch zerstörungsfrei vs. mechanisch invasiv/zer-störend), die laterale Größe des Integrationsgebietes der Messung (lokal:nano bis sub-mikro vs. global: mikro bis makro) und die Art der Bestimmung von Messunsicherheitsbudgets (physikalische Größen: direkt rückführbar; Werkstoffkenngröße: genormt; Systemkenngröße: genormt).
Im Rahmen von Industrie 4.0 werden ausgehend der geforderten Spezifikation des beschichteten Produkts (Mittelwert mit Vertrauensbereich oder Mindestwert) durchgehende Toleranzbänder zur Oberflächenmodifizierung/Beschichtung des Substrats, einhergehend mit Prozessfenstern, die diese Toleranzbänder garantieren, erforderlich, die zuverlässig erfasst werden müssen. Die Frage der anzuwendenden Mess- und Prüftechnik und die damit notwendige Betrachtung von Messunsicherheitsbudgets ist für die Digitalisierung von Konditionierungs-, Zustands-, Regel- und Steuergrößen unverzichtbar. Mit Blick auf die Einhaltung von Prozessfenstern und die dafür notwendige Prozessführung wird technologisches Kern-Know-how digitalisiert, das es unbedingt zu schützen gilt. Nur lokale Netze können diese Sicherheit garantieren, in globalen Netzen ist die Datensicherheit bestenfalls maximierbar.
Der Vortrag berichtet über die Auslagerung von Standardproben nach DIN EN ISO 9223 bis 9226 aus Zink, Stahl, Kupfer und Aluminium auf den verschiedenen atmosphärischen Bewitterungsständen der Bundesanstalt für Materialforschung und -prüfung (BAM). Im Vortrag werden die Masseverluste, Korrosionsgeschwindigkeiten und Korrosivitätskategorien der Standardproben im freibewitterten und überdachten Bereich nach einem Jahr vorgestellt und Unterschiede hinsichtlich der Atmosphärenbedingungen aufgezeigt. Freibewitterte Proben zeigen dabei deutliche Unterschiede hinsichtlich ihres Korrosionsverhaltens im Vergleich zu überdachten Proben. Die ermittelten Korrosivitätskategorien sind sowohl standort- als auch materialspezifisch.
Der Vortrag berichtet über die Auslagerung von Standardproben nach DIN EN ISO 9223 bis 9226 aus Zink, Stahl, Kupfer und Aluminium auf den verschiedenen atmosphärischen Bewitterungsständen der Bundesanstalt für Materialforschung und -prüfung (BAM). Im Vortrag werden die Masseverluste, Korrosionsgeschwindigkeiten und Korrosivitätskategorien der Standardproben im freibewitterten und überdachten Bereich nach einem Jahr vorgestellt und Unterschiede hinsichtlich der Atmosphärenbedingungen aufgezeigt. Freibewitterte Proben zeigen dabei deutliche Unterschiede hinsichtlich ihres Korrosionsverhaltens im Vergleich zu überdachten Proben. Die ermittelten Korrosivitätskategorien sind sowohl standort- als auch materialspezifisch.
Der Vortrag berichtet über die Auslagerung von Standardproben nach DIN EN ISO 9223 bis 9226 aus Zink, Stahl, Kupfer und Aluminium auf den verschiedenen atmosphärischen Bewitterungsständen der Bundesanstalt für Materialforschung und -prüfung (BAM). Im Vortrag werden die Masseverluste, Korrosionsgeschwindigkeiten und Korrosivitätskategorien der Standardproben im freibewitterten und überdachten Bereich nach einem Jahr vorgestellt und Unterschiede hinsichtlich der Atmosphärenbedingungen aufgezeigt. Freibewitterte Proben zeigen dabei deutliche Unterschiede hinsichtlich ihres Korrosionsverhaltens im Vergleich zu überdachten Proben. Die ermittelten Korrosivitätskategorien sind sowohl standort- als auch materialspezifisch.
The TED-GC-MS analysis is a two-step method. A sample is first decomposed in a thermogravimetric analyzer (TGA) and the gaseous decomposition products are then trapped on a solid-phase adsorber. Subsequently, the solid-phase adsorber is analyzed with thermal desorption gas chromatography mass spectrometry (TDU-GC-MS). This method is ideally suited for the analysis of polymers and their degradation processes. Here, a new entirely automated System is introduced which enables high sample throughput and reproducible automated fractioned collection of decomposition products. Strengths and limitations of the system configuration are elaborated via three examples focused on practical challenges in materials analysis and identification: i) separate analysis of the components of a wood-plastic-composite material, ii) quantitative determination of weight concentration of the constituents of a polymer blend and iii) quantitative analysis of model samples of microplastics in suspended particulate matter.
In additive manufacturing (AM) Laser Metal Deposition (LMD), parts are built by welding layers of powder feedstock onto a substrate. Applications for steel powders include forging tools and structural components for various industries. For large parts, the choice of tool-paths influences the build-rate, the part performance and the distortions in a highly geometry-dependent manner. With weld-path lengths in the range of hundreds of meters, a reliable, automated tool path generation is essential for the usability of LMD processes.
In this contribution, automated tool-path generation approaches are shown and their results are discussed for arbitrary geometries. The investigated path strategies are the classical approaches: “Zig-zag-” and “contour-parallel-strategies”. After generation, the tool-paths are automatically formatted into g-code for experimental build-up and ASCII for a numerical simulation model. Finally, the tool paths are discussed in regards to volume-fill, microstructure and porosity for the experimental samples.
This work presents a part of the IGF project 18737N “Welding distortion simulation” (FOSTA P1140)
To increase the competitiveness of jacket substructures compared to monopiles a changeover from an individual towards a serial jacket production based on automated manufactured tubular joints combined with standardized pipes has to be achieved. Therefore, this paper addresses fatigue tests of automatically welded tubular X-joints focusing on the location of the technical fatigue crack. The detected location of the technical crack is compared to numerical investigations predicting the most fatigue prone notch considering the structural stress approach as well as the notch stress approach. Besides, the welding process of the automated manufactured tubular X-joints is presented.
Der 60 °C-Betonversuch ist eine in Deutschland und international verbreitete Methode um die Empfindlichkeit von Gesteinskörnungen und Betonen hinsichtlich einer Alkali-Kieselsäure Reaktion (AKR) zu prüfen. Dieser Beitrag stellt eine neuentwickelte automatisierte Variante der Prüfmethode in einem Minireaktor vor. Dabei werden die Dehnungen von Betonprismen nicht, wie beim konventionellen Test manuell, sondern automatisch in entsprechend ausgerüsteten Prüfbehältern gemessen. Neben einer Reduzierung des Messaufwands bringt die automatisierte Prüfung im Minireaktor weitere Vorteile. Die Dehnungssignale werden, anders als bei der konventionellen Messung, quasi-kontinuierlich aufgezeichnet und bilden das Expansionsverhalten der Prismen detailliert ab. Außerdem bleiben Unterbrechungen der AKR-provozierenden Lagerung aus, die bei der konventionellen Prüfung notwendig sind. Im Beitrag werden die automatisierte und konventionelle Prüfung anhand der Dehnungen von Prismen zweier Gesteinskörnungen verglichen. In Übereinstimmung mit vorhergehenden Untersuchungen sind im Minireaktor gemessene Dehnungen systematisch kleiner als manuell gemessene. Als mögliche Ursache werden Unterschiede im Auslaugverhalten experimentell untersucht. Zur Überprüfung der Einstufung der zwei Gesteinskörnungen erfolgen außerdem Referenzprüfungen in der Nebelkammerlagerung bei 40 °C.
Automotive engine lubricants
(2019)
In 2003, ASTM Manual 37, Fuels and Lubricants Handbook: Technology, Properties, Performance and Testing, featured a chapter discussing automotive lubricants, including engine oils, automatic transmission fluids, manual transmission fluids, gear lubricants, and greases. This chapter, by Schwartz, Tung, and McMillan, surveyed all of these classes of lubricants, up to its publication in 2003.
More recently, the period between 2003 and 2010 has been addressed as part of a book copublished by ASTM and SAE International (coeditors Simon Tung and George Totten), where Fox surveyed the development of engine oil specifications that emerged during those years.
This chapter surveys the evolution of engine oil design and testing since 2002 and concludes with insights into future directions offered by recent tribological research. Our objective is to provide a reader new to the field with an understanding of the following:
- Engine oil composition and formulation
- North American engine oil specification development, and an outline of emergent European specifications
- How emergent specifications and legislative requirements are linked to the introduction of new engine hardware
- How tribological innovation can contribute to future enhancements in engine efficiency
In parallel, we will provide several tables comparing groups of contemporaneous specifications.
Avoid living dangerously: non-destructive characterization of AM parts from powder to end-of-life
(2019)
The freeform and the revolutionary design possibilities offered by additive manufacturing have skyrocketed the amount of optimization studies in the realm of engineering, and metallic additive manufactured parts are becoming a reality in industry.
Not surprisingly, this has not been paralleled by a similar enthusiastic wave in the realm of materials science, and still very little is known about AM materials properties. This has the consequence that, typically, conventional materials properties are still used in design and even in simulations.
lt is necessary to dig a lot deeper than at present, in order to understand these new materials classes, and in particular their microstructure and their intemal stresses, largely different from their cast or wrought companions.