Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Vortrag (292)
- Posterpräsentation (97)
- Beitrag zu einem Tagungsband (56)
- Zeitschriftenartikel (22)
- Dissertation (6)
- Forschungsdatensatz (5)
- Buchkapitel (3)
- Sonstiges (3)
- Forschungsbericht (3)
- Tagungsband (Herausgeberschaft für den kompletten Band) (2)
Sprache
- Englisch (362)
- Deutsch (127)
- Mehrsprachig (2)
Referierte Publikation
- nein (491) (entfernen)
Schlagworte
- Additive Manufacturing (87)
- Additive manufacturing (81)
- Thermography (42)
- Additive Fertigung (40)
- Residual stress (36)
- Computed tomography (33)
- Laser Powder Bed Fusion (26)
- Laser powder bed fusion (23)
- Residual Stress (23)
- Thermografie (23)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (491) (entfernen)
Defects are still common in metal components built with Additive Manufacturing (AM). Process monitoring methods for laser powder bed fusion (PBF-LB/M) are used in industry, but relationships between monitoring data and defect formation are not fully understood yet. Additionally, defects and deformations may develop with a time delay to the laser energy input. Thus, currently, the component quality is only determinable after the finished process.
Here, active laser thermography, a nondestructive testing method, is adapted to PBF-LB/M, using the defocused process laser as heat source. The testing can be performed layer by layer throughout the manufacturing process. We study our proposed testing method along experiments carried out on a custom research PBF-LB/M machine using infrared (IR) cameras.
Our work enables a shift from post-process testing of components towards in-situ testing during the AM process. The actual component quality is evaluated in the process chamber and defects can be detected between layers.
In the approval process of dangerous goods packagings, drop tests onto a flat, essentially unyielding surface are used to assess resistance against mechanical damage. International adopted regulations like ADR and RID define filling good dependent drop heights and filling degrees whilst the user needs to define the maximum gross mass to be tested and approved. Maximum packaging gross mass is defined conservatively and not reached in practice. To meet the defined gross mass in testing, using additives is permitted. However, in some cases, additives are not desirable due to packaging design or filling substance properties. This leads to deviations from the initial gross mass definition. Hence, a certain drop height adjustment is necessary to achieve the required impact loading. Laboratories frequently adjust drop height assuming a perfectly elastic collision which is inaccurate. Appropriate adjustment is not trivial due to energy conversion processes, e.g., plastic deformation. In this work, a test stand is developed for measuring the change in kinetic energy of different packaging designs and filling substances in regulative drop tests. The experimental results are used to validate finite-element (FE) models so that packaging properties can be varied in simulated drop test scenarios. The findings intend to describe the appropriate drop height adjustment of the respective packaging with same design but deviating gross mass to produce comparable mechanical response. The results are highly beneficial for testing laboratories, approval issuing authorities and packaging institutes confronted with the problem of testing packages with gross masses other than those to be approved.
The stress–strain behavior of certain ceramics, such as aluminum titanate (AT, Al2TiO5), has features that are unusual for brittle material. In particular, a substantial nonlinearity under uniaxial tension, and load–unload hysteresis caused by the increase of the incremental stiffness at the beginning of unloading. These features are observed experimentally and attributed to microcracking. In this study, we investigate the mechanical response of an AT material at room and high temperature. Microstructure and microcracking are analyzed by means of electron microscopy, and both synchrotron micro computed tomography (µCT) and refraction radiography (SXRR). Synchrotron refraction radiography is combined with in-situ heating at high-temperatures (up to 1400°C) to be able to monitor the relative closure of microcracks as a function of increasing/decreasing temperatures.
In der automatisierten Ultraschallprüfung von Komponenten mit komplexen Oberflächengeometrien werden zur Führung des Prüfkopfes zunehmend 6-Achsen-Roboter erprobt. Diese stellen die notwendige Automatisierbarkeit und Flexibilität bereit, um die lokal senkrechte Einschallung sicherzustellen. Durch den Einsatz von linearen Arrays und bildgebenden Verfahren können die Bilder oder die daraus extrahierten Merkmale zu einer Rekonstruktion in 3D zusammengesetzt werden. Die Anforderungen an die Prüfbahnen für die bildgebende Array-Ultraschallprüfung gehen dabei über konventionellen Bahnplanungsprogramme hinaus. Es wird ein Prozess vorgestellt, der Roboterbahnen auf der Grundlage des 3D-Modells von Körpern mit doppelt gekrümmter Oberfläche unter Berücksichtigung der Prüfparameter erzeugt. Hierbei wird zum einen die senkrechte Prüfkopfstellung und zum anderen eine optimale Abdeckung der Oberfläche realisiert. Dabei wird die lokale Oberflächengeometrie beachtet, da diese das Reflexionsverhalten beeinflusst und sich daher auf die optimale Verteilung und Orientierung der Prüfpositionen auswirkt. Damit einhergehend erfolgt eine Ablösung von konventionellen Konzepten, die auf linearen Prüfbahnen basieren, welches spannende neue Prüfstrategien eröffnet.
The stress–strain behavior of certain ceramics, such as aluminum titanate (AT, Al2TiO5), has features that are unusual for brittle material. In particular, a substantial nonlinearity under uniaxial tension, and load–unload hysteresis caused by the increase of the incremental stiffness at the beginning of unloading. These features are observed experimentally and attributed to microcracking. In this study, we investigate the mechanical response of an AT material at room and high temperature. Microstructure and microcracking are analyzed by means of electron microscopy, and both synchrotron micro computed tomography (µCT) and refraction radiography (SXRR). Synchrotron refraction radiography is combined with in-situ heating at high-temperatures (up to 1400°C) to be able to monitor the relative closure of microcracks as a function of increasing/decreasing temperatures.
Additive manufacturing is one of the most promising techniques for industrial production and maintenance, but the specifics of the layered structure must be considered. The Direct Energy Deposition-Arc process enables relatively high deposition rates, which is favourable for larger components. For this study, specimens with different orientations were prepared from one AISI316 steel block – parallel and orthogonal to the deposition plane. Quasistatic tensile loading tests were carried out, monitored by an infrared camera. The obtained surface temperature maps revealed structural differences between both orientations. The consideration of surface temperature transients yields more details about the behaviour of the material under tensile loading than the conventional stress-strain-curve. These preliminary investigations were supplemented by thermographic fatigue trials. Although the anisotropy was also observed during fatigue loading the fatigue behaviour in general was the same, at least for both inspected specimens. The presented results demonstrate the abilities and the potential of thermographic techniques for tensile tests.
Im Rahmen des Projektes MRO2.0, das sich mit der digitalen Transformation des Servicezyklus von modernen Gasturbinenschaufeln beschäftigt, wurde gezeigt, wie sich automatisiert und flächendeckend die (Rest-)Wanddicke an variabel gekrümmten Prüfgeometrien bestimmen lässt. Es wurde ein Roboterarm verwendet, der ein lineares Ultraschallarray in Tauchtechnik führt und Prüfdaten aufnimmt, die mit einer adaptierten TFM (Total Focusing Method) zu Rekonstruktionen der Außen- und Innenoberfläche verarbeitet werden. In der aktuellen zweiten Projektphase wird die Methode für Werkstoffe erweitert, die anisotrope akustische Eigenschaften aufweisen. In diesem Beitrag wird eine Methode vorgestellt, wie sich die Kristallausrichtung bzw. die richtungsabhängige Schallgeschwindigkeit mittels eines linearen Ultraschallarrays bestimmen lässt. Für den Sendefall eines Randelements in Kontakttechnik können dabei Wellen identifiziert werden, die sich parallel zur Prüfkopfapertur im Prüfobjekt ausbreiten und mit der richtungsabhängigen Schallgeschwindigkeit skalieren. Die ermittelte Schallgeschwindigkeitsverteilung kann dann verwendet werden, um die lokale Wanddickenbestimmung für die Anisotropie zu adaptieren.
Ultrasonic testing (UT) of objects with complex geometries often requires the use of a robotic arm to position the probe perpendicular to the local surface. Using immersion makes it possible to test these objects with standard ultrasonic linear array probes. Here, the probe positions and orientations provided by the robot are used for merging the locally acquired image data into a 3D-reconstruction. The quality of this reconstruction is highly dependent on the alignment of the tool center point (TCP) of the physical probe with the TCP used in the digital model. For common industrial tools, the TCP is usually acquired using geometric features of the tools. However, for ultrasonic arrays in immersion, there is a water standoff between the probe and the test object, therefore the TCP is in free space in front of the array and cannot be acquired with the common method. To overcome this challenge, we propose a method that allows the robotic ultrasonic system to automatically self-adjust the positioning of the UT probe using a test block made of steel with defined geometric features as a target for referencing. For each of the six degrees of freedom, a scan and adjustment routine are established using the data acquired by the UT probe to update the TCP’s position and orientation in the robot control. Given a coarse pre-definition of the TCP and the known target test block, no human interaction is required while the system determines the optimum tool position and orientation. Part of this work will be used to improve and extend standards for robotic ultrasonic test systems, e.g. ISO 24647.
Laser Powder Bed Fusion (PBF-LB/M) is a layer wise metal additive manufacturing (AM) technology, which enables significant advancements of component design, leading to potential efficiency and performance improvements. However, the thermal cycles inherent to the process comprising large localized thermal gradients and repeated melting and solidification cycles leads to the generation of high magnitude residual stresses. These residual stresses can be detrimental both during manufacturing of components and in subsequent application. Therefore, a deep understanding of the influence of process parameters on the residual stresses are crucial for efficient manufacturing and safe application. The experimental characterization of these residual stresses is therefore crucial and can provide a reliable baseline for simulations of both the process and applications.
Diffraction-based methods for residual stress analysis using penetrating neutrons and high energy X-rays enable non-destructive spatially resolved characterization of both surface and bulk residual stresses. However, the unique microstructural features inherent to the process can challenge some of our assumptions when using these methods. These challenges include the determination of a stress-free reference, the use of correct elastic constants (both SCEC and DEC) and the influence of surface roughness, texture, and porosity on residual stresses.
This presentation will detail recent insights and recommendations for the characterization of residual stresses in a range of PBF-LB/M metallic alloys (Fe, Ni, Al and Ti)
The determination of residual stress in additively manufactured materials is a challenge, even after decades from the establishment of the basics of residual stress analysis. This is due to the peculiar microstructure of such materials. In fact, researchers have discovered that conventional methods for the determination of RS in materials do not properly work for AM materials. In this tutorial, the basics of RS analysis will be explained, together with the basics of AM manufacturing techniques. The microstructure of the peculiar materials (AM) dealt with here will be elucidated. Successively, the necessary modifications to the conventional approaches to RS analysis will be explained and case studies will be displayed, for the attendant to touch with hands the peculiarities of the approaches. Finally, a few experimental and theoretical tips will be given on dos and don’ts for a correct determination of RS in AM materials.