Analytische Chemie
Filtern
Dokumenttyp
- Vortrag (3)
- Beitrag zu einem Tagungsband (1)
- Sonstiges (1)
Referierte Publikation
- nein (5)
Schlagworte
- Recycling (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (3)
In dem Projekt soll die vollständige Wiederverwertbarkeit der Schlacke und ihrer Bestandteile demonstriert werden. Dazu gehören die vollständige Rückgewinnung der metallischen Phase, die in die Edelstahlherstellung zurückgeführt werden kann, sowie die Aufwertung der mineralischen Fraktion, die ihre uneingeschränkte Verwendung als Zementzumahlstoff oder mineralischer Baustoff erlaubt. Bei geeigneter Prozessführung des elektrischen Lichtbogenofens können durch „reduzierendes Schmelzen“ die chromhaltigen Wertstoffe zusammen mit anderen Schwermetallen zu 97% in einer Metalllegierung angereichert und separiert werden. Diese kann als Rohstoff in der Metallurgie eingesetzt werden. Der Chromgehalt der mineralischen Komponte der Schlacke konnte von ca. 3% auf unter 0,1% verringert werden. Die mineralische Fraktion lässt sich durch entsprechende Zuschläge während des Schmelzbetriebes und eine anschließende Granulation der schmelzflüssigen Phase zu einem Material aufwerten, das in seiner Zusammensetzung und seinen Eigenschaften typischen Zementkomponenten entspricht und als Rohstoff in der Zementproduktion eingesetzt werden kann. Dafür müssen allerdings noch die rechtlichen Voraussetzungen geschaffen werden, da der Rohstoffeinsatz gerade im Zement strengen Auflagen unterliegt und die Zemente bestimmte Normen erfüllen müssen.
Durch die in RECARC aufgezeigte Möglichkeit der Wiederverwertung können somit Stoffkreisläufe geschlossen werden, die ansonsten zu einem Verlust wertvoller Rohstoffe führen. Vor allem die steigenden Rohstoffkosten, aber auch die immer stärker limitierten CO2-Emissionen zeigen die hohe Relevanz im Umgang mit metallurgischen Reststoffen. Eine Überführung des in RECARC demonstrierten Verfahrens in die Industrie könnte einen wichtigen Beitrag zur nachhaltigen Schonung der natürlichen Ressourcen und der Umwelt leisten.
Closed material cycles and unmixed material fractions are required to achieve high recovery and recycling rates in the building industry. The growing diversity of construction and demolition waste is leading to increasing difficulties in separating the individual materials. Manual sorting involves many risks and dangers for the executing staff and is merely based on obvious, visually detectable differences for separation. An automated, sensor-based sorting of these building materials could complement or replace this practice to improve processing speed, recycling rates, sorting quality, and prevailing health conditions.
A joint project of partners from industry and research institutions approaches this task by investigating and testing the combination of laser-induced breakdown spectroscopy (LIBS) and visual (VIS)/ near-infrared (NIR) spectroscopy. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3-containing building materials (gypsum, aerated concrete, etc.). Focusing on Berlin as an example, the entire value chain will be analyzed to minimize economic/technological barriers and obstacles at the cluster level and to sustainably increase recovery and recycling rates.
First LIBS measurements show promising results in distinguishing various material types. A meaningful validation shall be achieved with further practical samples. Future works will investigate the combination of LIBS and VIS/NIR spectroscopy in a fully automated measurement setup with conveyor belt speeds of 3 m/s.
In a joint project of partners from industry and research, the automated recycling of construction and demolition waste (CDW) is investigated and tested by combing laser-induced breakdown spectroscopy (LIBS) and near-infrared (NIR) spectroscopy. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3-cotaining building materials (gypsum, aerated concrete, etc.). The project focuses primarily on the Berlin site to analyze the entire value chain, minimize economic/technological barriers and obstacles at the cluster level, and sustainably increase recovery and recycling rates. First measurements with LIBS and NIR spectroscopy show promising results in distinguishing various material types and indicate the potential for a successful combination. In addition, X-ray fluorescence (XRF) spectroscopy is being performed to obtain more information about the quantitative elemental composition of the different building materials. Future work will apply the developed sorting methodology in a fully automated measurement setup with CDW on a conveyor belt.
In a joint project of partners from industry and research, the automated recycling of construction and demolition waste (CDW) is investigated and tested by combing laser-induced breakdown spectroscopy (LIBS) and near-infrared (NIR) spectroscopy. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3-cotaining building materials (gypsum, aerated concrete, etc.). The project focuses primarily on the Berlin site to analyze the entire value chain, minimize economic/technological barriers and obstacles at the cluster level, and sustainably increase recovery and recycling rates. First measurements with LIBS and NIR spectroscopy show promising results in distinguishing various material types and indicate the potential for a successful combination. In addition, X-ray fluorescence (XRF) spectroscopy is being performed to obtain more information about the quantitative elemental composition of the different building materials. Future work will apply the developed sorting methodology in a fully automated measurement setup with CDW on a conveyor belt.
LIBS ConSort: Development of a sensor-based sorting method for constuction and demolition waste
(2023)
Closed material cycles and unmixed material fractions are required to achieve high recovery and recycling rates in the building industry. In construction and demolition waste (CDW) recycling, the preference to date has been to apply simple but proven techniques to process large quantities of construction rubble in a short time. This is in contrast to the increasingly complex composite materials and structures in the mineral building materials industry. Manual sorting involves many risks and dangers for the executing staff and is merely based on obvious, visually detectable differences for separation. An automated, sensor-based sorting of these building materials could complement or replace this practice to improve processing speed, recycling rates, sorting quality, and prevailing health conditions. A joint project of partners from industry and research institutions approaches this task by investigating and testing the combination of laser-induced breakdown spectroscopy (LIBS) with near-infrared (NIR) spectroscopy and visual imaging. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3-cotaining building materials (gypsum, aerated concrete, etc.) Focusing on Berlin as an example, the entire value chain will be analyzed to minimize economic / technological barriers and obstacles at the cluster level and to sustainably increase recovery and recycling rates. We present current advances and results about the test stand development combining LIBS with NIR spectroscopy and visual imaging. In the future, this laboratory prototype will serve as a fully automated measurement setup to allow real-time classification of CDW on a conveyor belt.