Leichtbau
Filtern
Dokumenttyp
- Vortrag (11)
- Zeitschriftenartikel (5)
- Beitrag zu einem Tagungsband (3)
- Buchkapitel (1)
- Posterpräsentation (1)
- Preprint (1)
Schlagworte
- Laser (9)
- NDT (5)
- Thermografie (4)
- Thermography (4)
- DLP (3)
- DMD (3)
- Super-Resolution (3)
- ZfP (3)
- Additive manufacturing (2)
- Air-coupled ultrasonic transducers (2)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (16)
- 8.3 Thermografische Verfahren (11)
- 9 Komponentensicherheit (5)
- 7 Bauwerkssicherheit (4)
- 9.4 Integrität von Schweißverbindungen (3)
- 7.4 Baustofftechnologie (2)
- 7.5 Technische Eigenschaften von Polymerwerkstoffen (2)
- 8.4 Akustische und elektromagnetische Verfahren (2)
- 9.2 Versuchsanlagen und Prüftechnik (2)
- 9.3 Schweißtechnische Fertigungsverfahren (2)
In this work, we continue to develop and investigate the Thermal Shock Response Spectrum (TSRS) method as an alternative data processing method for infrared thermography (IRT). We focus on improving the current TSRS algorithm and present an optimization methodology for finding the optimal thermal Q-factor and characteristic frequency pair, which is based on the widely applied random sampling method. We show the qualitative relationship between the determined optimal characteristic frequency and the corresponding maximum difference in diffusion length between reference and defective models, as calculated by selecting a specific one-dimensional thermal N-layer model. The investigations were performed on an inhomogeneous plate made of carbon fiber reinforced polymer (CFRP) with artificial square defects at different depths. Furthermore, two different heat sources were used: a xenon flash lamp and a laser. These sources are not only distinct by their underlying physics but also generate inherently different pulse shapes. To quantitatively estimate the contrast between defect and non-defect areas, and to compare these results with commonly used infrared thermography (IRT) data post-processing methods such as Pulse Phase Thermography (PPT) and Thermographic Signal Reconstruction (TSR), the Tanimoto criterion (TC) and signal-tonoise ratio (SNR) were used.
The main advantage of air-coupled ultrasonic testing is the absence of a liquid couplant, which can damage some materials. However, most air-coupled testing scenarios have the challenge of low signals and a signal-to-noise ratio (SNR) several orders of magnitude lower than with couplant-assisted techniques. Since this challenge of small SNR also exists in radar technology, the pulse compression used there was adapted and applied to the physical conditions of air-coupled ultrasonic testing. This paper presents ultrasonic transmission measurements on a carbon-fibre-reinforced polymer plate using two experimental setups: 1) a thermoacoustic transmitter and an optical microphone and 2) a pair of ferroelectret transducers as transmitter and receiver. Thermoacoustic transmitters convert electrical energy to heat, which causes the air to expand thus producing acoustic waves. The optical microphone is based on a Fabry-Perot interferometer. Ferroelectrets are charged cellular polymers, having piezoelectric properties and excellent acoustic matching to air. Both thermoacoustic transmitters and ferroelectrets are non-linear regarding the relationship between the excited sound pressure and the excitation voltage. Due to these physical boundary conditions, unipolar coding was used to modulate the excitation signals. Various codes were tested, and parameters of the excitation pulses were varied to find the optimal combination for each experimental setup. The application of pulse compression to the combination of thermoacoustic transmitter and optical microphone increased the signal-to-noise ratio by up to 16 dB and for the ferroelectret transducers by up to 23 dB.
The main advantage of air-coupled ultrasonic testing is the absence of a liquid couplant, which can damage some materials. However, most air-coupled testing scenarios have the challenge of low signals and a signal-to-noise ratio (SNR) several orders of magnitude lower than with couplant-assisted tech-niques. Since this challenge of small SNR also exists in radar technology, the pulse compression used there was adapted and applied to the physical conditions of air-coupled ultrasonic testing. This paper presents ultrasonic transmission measurements on a carbon-fibre-reinforced polymer plate using two experimental setups: 1) a thermoacoustic transmitter and an optical microphone and 2) a pair of ferroe-lectret transducers as transmitter and receiver. Thermoacoustic transmitters convert electrical energy to heat, which causes the air to expand thus producing acoustic waves. The optical microphone is based on a Fabry-Perot interferometer. Ferroelectrets are charged cellular polymers, having piezoelectric proper-ties and excellent acoustic matching to air. Both thermoacoustic transmitters and ferroelectrets are non-linear regarding the relationship between the excited sound pressure and the excitation voltage. Due to these physical boundary conditions, unipolar coding was used to modulate the excitation signals. Vari-ous codes were tested, and parameters of the excitation pulses were varied to find the optimal combina-tion for each experimental setup. The application of pulse compression to the combination of thermo-acoustic transmitter and optical microphone increased the signal-to-noise ratio by up to 16 dB and for the ferroelectret transducers by up to 23 dB.
Anisotropy investigation of a single crystal superalloy using laser-spot infrared thermography
(2024)
Thermal property investigation of anisotropic materials such as single crystal superalloys are still in interest of practical and fundamental reasons but remains challenging using conventional testing methods. In this study, a single crystal superalloy is tested using laser-spot thermography, and its thermal anisotropy is investigated. Determining anisotropic thermal conductivity at microscopic scales is challenging, as it appears isotropic at the macroscopic scale. Infrared thermography is one of the best-known techniques for measuring material heat transfer properties and facilitating visualization of temperature distribution through the specimen. The proposed study uses the active thermography method of laser-spot infrared thermography, in which a laser spot is focused onto the sample surface and the thermal response is captured from the surface of the specimen with an infrared camera. A detailed analysis of temperature gradients and heat diffusion patterns aids in the measurement of thermal conductivity values along the sample's different crystallographic directions. The directional bonding characteristics and inherent crystallographic structure of the alloy account for the in-plane thermal conductivities calculated from experimental thermal measurements. The laser-spot thermography method has proven to be an effective tool for mapping the material's thermal conductivity anisotropy with high sensitivity and high spatial and temporal resolution. The investigation into the anisotropy of the material provides an insight into heat flow in the structure and helps in optimizing the design and overall performance of the material system.
Modern laser systems have proven to be versatile heat sources for active thermographic testing applications. Compared to more traditional light sources, e.g. flash or halogen lamps, their output power can be easily modulated at high rates, allowing a wide variety of complex excitations to be realized. Although their total optical output power can be theoretically scaled to arbitrary values, the maximum output power is practically limited by many factors: the maximum power that the sample under test can absorb without altering the lighted surface itself, the trade-off between power density and inspected area, the cost of the laser system, etc. Furthermore, when working with spatial modulator systems, the output power could be limited to avoid provoking any damages on such devices. Nevertheless, to guarantee sufficient heating even for highly thermally conductive materials and/or deeply buried defects, the heating times can be extended, e.g., either by using step heating, long pulse thermography, or by lock-in thermography with a continuously modulated heating. However, for all these approaches, the ranging capabilities of the thermographic defect detection are reduced due to the limited frequency content of the excitation.
To tackle this problem, i.e. to increase the excitation energy while preserving its frequency content, new approaches have been developed in the last two decades, among which the use of coded excitations combined with pulse-compression, and the use of multiple lock-in analysis or of a frequency modulated excitation signal. The challenges of such temporally structured heating techniques are manifold, for example, the DC component inherent in optical heating must be taken into account. In general, a wider frequency bandwidth or greater variability of the frequency components also means greater complexity for signal generation and data processing. In this paper, temporal structured excitation schemes with different degrees of complexity are compared on a high power laser system.
Die Integration von Automation und Robotik in die Prüfprozesse ermöglicht die
Untersuchung komplexer Bauteile. Diese Studie präsentiert die robotergestützte
Laserthermografie, um Risse in solchen Bauteilen zu identifizieren und analysieren. Diese Technik ermöglicht die automatisierte Rissprüfung welche im Vergleich zur Farbeindringprüfung auf viele, meist manuelle, Arbeitsschritte sowie die notwendigen Chemikalien verzichtet.
Zusätzlich wird ein automatisiertes Einscannen der Bauteile mithilfe eines
Linienscanners vorgestellt. Dieser Schritt ermöglicht eine detaillierte 3D-Rekonstruktion der Bauteilgeometrie und ermöglicht eine einfache Korrektur von Abweichungen in der Bauteilaufnahme und eröffnet Möglichkeiten zur adaptiven Bahnplanung bei Bauteilverformungen.
Die Rückprojektion der gefundenen Risse auf die Oberfläche des Bauteils kann
automatisiert erfolgen. Dieser Schritt erlaubt nicht nur die Identifikation der Risse, sondern auch eine genauere Analyse ihrer Geometrie und Lage am Bauteil.
Die Kombination von robotergestützter Laserthermografie, automatisiertem 3DScanning und Rückprojektion der Risse auf die Bauteiloberfläche eröffnet neue
Möglichkeiten in der zerstörungsfreien Prüfung von komplexen Bauteilen und erweitert damit mögliche Anwendungsfelder.
The systematic transfer of solvent-free, additive flame retardant (FR) formulations from epoxy resins to glass fiber-reinforced epoxy composites (GFRECs) through prepregs is difficult. Additionally, obtaining data on their post-fire mechanics is often challenging. Utilizing melamine polyphosphate (MPP), ammonium polyphosphate (APP), and silane-coated ammonium polyphosphate (SiAPP) FRs with low-melting inorganic silicates (InSi) in an 8:2 proportion and 10% loading by weight in a diglycidyl ether of bisphenol A (DGEBA) resin, a systematic investigation of the processing properties, room-temperature mechanics, and temperature-based mechanics of the systems was performed. The resin was cured with a dicyandiamide hardener (DICY) and a urone accelerator. The results revealed no substantial impact of these FRs at the current loading on the resin's glass transition temperature or processability. However, the fire residues from cone calorimetry tests of the composites containing FRs were found to be only 15-20% of the thickness of the resins, implying a suppression of intumescence upon transfer. At room temperature, the decrease in the flexural modulus for the composites containing FRs was negligible. Exposure of the composites in a furnace at 400°C as a preliminary study before ignition tests was shown to cause significant flexural moduli reductions after 2.5 min of exposure and complete delamination after 3 min making further testing unviable. This study emphasizes the need for future research on recovering modes of action upon transfer of FR formulations from resins to composites. Based on the challenges outlined in this investigation, sample adaptation methods for post-fire analysis will be developed in a future study.
The aim of the ZIKA research project, funded by the BMBF funding program FORKA (FKZ:15S9446 A-C), is the automated detection of internal corrosion of radioactive drums using non-destructive testing (NDT). The newly gained findings will be combined with research results from the previous project EMOS (FKZ:15S9420), which dealt with the external damage of drums. Using NDT, internal corrosion and possible internal sources of damage can be identified before they become a safety-relevant issue. However, if internally sourced damages can be seen externally, the integrity of the damaged drum is no longer guaranteed, which has significant consequences. Therefore, early detection before integrity failure is of particular importance for interim storage facilities with low- and medium-level radioactive waste drums.
Sacrifice Few to Save Many: Fire Protective Interlayers in Carbon- Fiber-Reinforced Laminates
(2024)
The fire protection of carbon-fiber-reinforced polymer (CFRP) laminates often relies on flame-retardant coatings, but in some applications, their efficacy may diminish upon direct fire exposure due to rapid pyrolysis. This study introduces an innovative approach by integrating protective interlayers within the laminate structure to enhance the fire resistance. Various materials, including ceramic composite WHIPOX, titanium foil, poly(etherimide) (PEI) foil, basalt fibers, rubber mat, and hemp fibers, were selected as protective interlayers. These interlayers were strategically placed within the laminate layout to form a sacrificial barrier, safeguarding the integrity of the composite. Bench-scale fire resistance tests were conducted, where fire (180 kW/m2) was applied directly to the one side of the specimen by a burner while a compressive load was applied at the same time. Results indicate significant prolongation of time to failure for CFRP laminates with protective interlayers, which is up to 10 times longer. This innovative approach represents a potential advance in fire protection strategies for CFRP laminates, offering improved resilience against fire-induced structural failure.
In infrared thermography, the interaction of the heat flow with the internal geometry or inhomogeneities in a sample and their effect on the transient temperature distribution is used, e.g., to detect defects non-destructively. An equivalent way of describing this is the propagation of thermal waves inside the sample. Although thermography is suitable for a wide range of inhomogeneities and materials, the fundamental limitation is the diffuse nature of thermal waves and the need to measure their effect radiometrically at the sample surface only. The crucial difference between diffuse thermal waves and propagating waves, as they occur, e.g., in ultrasound, is the rapid degradation of spatial resolution with increasing defect depth. This degradation usually limits the applicability of thermography for finding small defects on and below the surface.
A promising approach to improve the spatial resolution and thus the detection sensitivity and reconstruction quality of the thermographic technique lies in the shaping of these diffuse thermal wave fields using structured laser thermography.
Some examples are:
• Narrow crack-like defects below the surface can be detected with high sensitivity by superimposing several interfering thermal wave fields,
• Defects very close to each other can be separated by multiple measurements with varying heating structures,
• Defects at different depths can be distinguished by an optimized temporal shaping of the thermal excitation function,
• Narrow cracks on the surface can be found by robotic scanning with focused laser spots.
We present the latest results of this technology obtained with high-power laser systems and modern numerical methods.