3.5 Sicherheit von Gasspeichern
Filtern
Dokumenttyp
- Vortrag (68)
- Zeitschriftenartikel (10)
- Beitrag zu einem Tagungsband (9)
- Posterpräsentation (2)
- Dissertation (1)
- Forschungsbericht (1)
Schlagworte
- Hydrogen (28)
- Safety (15)
- Wasserstoff (15)
- H2Safety@BAM (12)
- Composite (8)
- Pressure vessel (8)
- Wasserstoffspeicher (8)
- Druckbehälter (7)
- Sicherheit (7)
- Structural health monitoring (7)
Organisationseinheit der BAM
- 3 Gefahrgutumschließungen; Energiespeicher (91)
- 3.5 Sicherheit von Gasspeichern (91)
- 8 Zerstörungsfreie Prüfung (22)
- 8.6 Faseroptische Sensorik (11)
- 2 Prozess- und Anlagensicherheit (9)
- 2.1 Sicherheit von Energieträgern (9)
- 8.4 Akustische und elektromagnetische Verfahren (9)
- 1 Analytische Chemie; Referenzmaterialien (8)
- 1.4 Prozessanalytik (8)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (7)
Das Bundesverkehrsministerium hat seit 2008 in drei Stufen jeweils auf Vorschlag der BAM einen Antrag zur Einführung bzw. Regulierung von Bergungsdruckgefäßen bei den Vereinten Nationen eingebracht. Die Anträge führten jeweils nach der Delegation in eine Arbeitsgruppe unter der Leitung des Vortragenden zu neuen Vorschriften im internationalen Gefahrguttransportrecht.
Zuletzt hat das UN-Subcommittee der Experten für den Transport gefährlicher Güter der Einführung einer Druck-Volumen-Begrenzung für Druckgefäße zugestimmt. Mit dieser Begrenzung wurde die bisherige Volumenbegrenzung für Bergungsdruckgefäße ersetzt, wodurch nun das Spektrum der Bergungsdruckgefäße gestaltet werden kann, das notwendig wäre, um defekte Druckgefäße transportieren zu können.
Das zentrale Kriterium für die Begrenzung des Druck-Volumen-Produktes (pV) fand bereits in den Landverkehrsvorschriften ADR/RID bis zu ihrer Neustrukturierung auch als Konsequenzmaß Verwendung. Damit soll sichergestellt werden, dass sich aus Wasserstofftransporten in Druckgefäßen keine Konsequenz entwickeln kann, die nach den Kriterien für stationäre Anlagen, einer Katastrophe gleichkommen würde.
Hierzu hatte eine Arbeitsgruppe der Vereinten Nationen seit 2020 auf Vorschlag der BAM eine Kette aufeinander aufbauende Kriterien diskutiert, die im Vortrag vorgestellt werden:
Einfluss der Druckwellen auf den menschlichen Körper (ohne Splitterwirkung oder Umsetzung der chemischen Energie) – Zusammenhang von Druckwelle und Fläche – Druckwellenberechnung – Bevölkerungsdichte – Grenzwerte für eine Katastrophe – resultierendes pV-Produkt.
Das Ergebnis wurde mit herausragenden Großunfällen und Katastrophen aus dem Gefahrguttransport und Gefahrstoffbereich verglichen. Außerdem wurden noch die Effekte des Temperatureinflusses auf den maximalen Betriebsdruck diskutiert. Zuletzt wurde bei den UN darauf hingewiesen, dass mit Blick auf die Auswirkungsbetrachtung der Wassersoff das Gas mit den geringsten Konsequenzen bei gegeben Druk-Volumen-Produkt ist, was zu restriktiveren Obergrenzen für z.B. Erdgas führen könnte.
Als letzter Punkt im Vortrag wird erläutert, dass in den kommenden UN-Sitzungen über nachfolgende Änderungen im Recht, wie z.B. der Kennzeichnung des pV-Produktes, diskutiert werden wird. Außerdem muss ein neuer Einstieg für die bei ISO in der Normung befindliche Umschließungen mit einem größeren pV-Produkt gefunden werden, wozu aber Transportland-spezifische Risikoanalysen in Verbindung mit massiven Fahrwegsbeschränkungen zu erwarten sind.
Mit der Initiative QI-Digital werden völlig neue Perspektiven für das Sicherheitsmanagement und die Qualitätssicherung technischer Anlagen erschaffen. Unsere Forschung im Kontext einer Wasserstofftankstelle zeigt, wie digitale Innovationen und Verfahren die Herausforderungen effizienter und verlässlicher Qualitätssicherung für komplexe Anlagen bewältigen können.
In diesem Vortrag werden Potentiale und Beispiele der digitalen QI für technische Anlagen demonstriert und diskutiert: Moderne Anlagenüberwachung mit digitalen Zwillingen und KI sowie Kalibriermanagement mithilfe digitaler Kalibrierscheine und elektronischem Siegel.
Durch Einsatz neuer Technologien im Transport von komprimiertem Wasserstoff konnte eine Verdreifachung des Nutzlastverhältnisses erreicht werden. Diese neuen Speicher auf den Transportfahrzeugen müssten aber anders auf ihre Sicherheit überprüft werden, als dies heute gefordert wird.
Mit dem Markthochlauf Wasserstoff vervielfacht sich zudem die Anzahl der Transporteinheiten. Da sich im Zuge der neuen H2-Transportfahrzeuge aber auch die Anzahl der einzelnen Speicher pro Fahrzeug etwa verzwanzigfacht hat, kommen die Kapazitäten für die erforderliche wiederkehrende Prüfung an ihre Grenzen.
Dies könnte evtl. durch eine entsprechende Erhöhung der Prüfkapazitäten gelöst werden. Da dies aber weder praktisch machbar ist noch technisch wirklich sinnvoll, müssen alternative Ansätze z.B. durch digital erfasste zerstörungsfreie Prüfkonzepte gesucht werden. Hierzu bedarf es aber einer Lebenslaufakte, die beginnend von der Definition einer Bauweise über die Baumusterprüfung, Zulassung, Herstellung, erstmalige Prüfung, Verwendung und wiederkehrenden oder begleitenden Prüfungen bis zum Verschrotten alle Daten erfassen und verwalten kann.
Eine solche Lebenslaufakte könnte auch als eine Art digitaler Produktpass (DPP) verstanden werden.
With the fast development in the field of additive manufacturing, triply periodic minimal surface (TPMS) based porous media have recently found many uses in mechanical property tuning. However, there is still a lack of understanding in their porosity-dependent permeability and electrical as well as thermal conductivity. Here, we perform finite volume simulations on the solid and void domains of the Schoen gyroid (SG), Schwarz primitive (SP) and Schwarz primitive beam (SPB) TPMS with porosities between 63% and 88% in Ansys Fluent. A simple cubic lattice (CL) of equivalent porosity served as reference. The SPB and CL showed up to one order of magnitude higher permeabilities than the SG and SP. However, SG and SP have about 1.3 and 2.6 times the electrical and thermal conductivity of SPB and CL, respectively. Furthermore, the properties of SPB and CL are largely affected by the surface area density, whereas tortuosity variation does not impact permeability and conductivity to a major extent. Finally, empirical relations are adapted to describe the presented data and thus, they may enable future designers of TPMS based porous structures to fine-tune the geometries according to the requirements on permeability and electrical as well as thermal conductivity.
Um die internationale Spitzenposition deutscher Unternehmen der Prozessindustrie auch in Zukunft sicher zu stellen, müssen die Unternehmen ihre Prozesse und Geschäftsabläufe digitalisieren und gemeinsam mit der Forschung innovative neue Methoden, Apparate, Anlagen, Sensoren und Automatisierungstechnik sowie Datenkonzepte entwickeln. All dies erfordert den Aufbau neuer Fähigkeiten, Investition in Talente, interdisziplinäre Kommunikation zwischen verschiedenen Personen und Abteilungen und eine Bereitschaft zur Veränderung.
We analyse electromotive force measurements of concentration cells using non-equilibrium thermodynamics, and determine the transference coefficients of ion-exchange membranes in aqueous KCl solutions. By taking advantage of the analytical expression for the permselectivity, we extract transport coefficients with high accuracy. The transport number of K+ and the transference coefficient of water in the Selemion CMVN cationexchange membrane are found to be 100𝑡K+ = 99.59 ± 0.56 and 𝑡𝑤 = 3.69 ± 0.40 respectively, while for the Selemion AMVN anion-exchange membrane they are 100𝑡Cl− = 100.21 ± 0.37 and 𝑡𝑤 = −3.75 ± 0.27. These results suggest that the membranes are perfectly selective to the target ion, and that each ion carries 3-4 water molecules through the membrane, which reduces the membrane permselectivity. In these concentration cells, the electrical potential contribution of the membrane alone was more easily isolated with bare Ag/AgCl electrodes without reference solutions and liquid junction plugs. Additionally, we find a large contribution to the measured concentration cell voltage from concentration gradients across the porous plug of the reference electrode, which cannot be explained by Henderson’s equation alone. For most of the concentration range, the transport number of the porous plug is determined to be 100𝑡K+ = 49.43 ± 0.78 with negligible water transport, similar to literature values for bulk electrolyte. In dilute electrolyte solutions with concentrations below 0.1 mol kg−1, the plug shows anomalous behaviour consistent with an increase in K+ selectivity and water co-transport.
Degradation and damage analysis of composite pressure vessels via experimental modal analysis
(2023)
For mobile gas storage systems, the application of type IV pressure vessels is state of the art. Type IV tanks consist of an inner polymer liner fully wrapped with fibre-reinforced plastic (FRP). Because of the complex fabric of the FRP as well as a difficulty estimable interaction behaviour between the single components under load, there are still no satisfying non-destructive testing methods to assess the current state of failure nor to estimate the level of degradation accurately and economically. At BAM division 3.5, analysing the ageing process of mobile composite pressure vessels is a major task to ensure safe usage over the whole lifetime. In this context, key aspects of our ongoing research activities are the invention of new test procedures and the development of accurate lifetime prediction models. In order to determine the level of degradation or damage, one meaningful non-destructive approach is to analyse the structural dynamic behaviour via an experimental modal analysis (EMA). Over the last few years, different types and sizes of composite pressure vessels have been tested in several research projects. The presented paper gives an insight into how to extract and interpret modal parameters and how to fit them to the results of residual strength tests.
Degradation and damage analysis of composite pressure vessels via experimental modal analysis
(2023)
For mobile gas storage systems, the application of type IV pressure vessels is state of the art. Type IV tanks consist of an inner polymer liner fully wrapped with fibre-reinforced plastic (FRP). Because of the complex fabric of the FRP as well as a difficulty estimable interaction behaviour between the single components under load, there are still no satisfying non-destructive testing methods to assess the current state of failure nor to estimate the level of degradation accurately and economically. At BAM division 3.5, analysing the ageing process of mobile composite pressure vessels is a major task to ensure safe usage over the whole lifetime. In this context, key aspects of our ongoing research activities are the invention of new test procedures and the development of accurate lifetime prediction models. In order to determine the level of degradation or damage, one meaningful non-destructive approach is to analyse the structural dynamic behaviour via an experimental modal analysis (EMA). Over the last few years, different types and sizes of composite pressure vessels have been tested in several research projects. The presented paper gives an insight into how to extract and interpret modal parameters and how to fit them to the results of residual strength tests.