Wissenschaftliche Artikel der BAM
Filtern
Dokumenttyp
Schlagworte
- Thermography (3)
- Thermografie (2)
- Active thermography (1)
- Additive Manufacturing (1)
- Additive manufacturing (1)
- Beton-Oberflächenschutzsysteme (1)
- Betonbeschichtung (1)
- CFRP (1)
- Concrete (1)
- Defect detection (1)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (12) (entfernen)
Weather-dependent passive thermography and thermal simulation of in-service wind turbine blades
(2023)
. To cope with the increase in the manufacturing and operation of wind turbines, wind farm operators need inspection tools that are able to provide reliable information while keeping the downtime low. Current inspection techniques require to stop the wind turbine. This work presents the current progress in the project EvalTherm, in which passive thermography is evaluated as a possible non-destructive inspection tool for operational wind turbine blades (WTBs). A methodology to obtain thermal images of rotating WTBs has been established in this project. However, the quality of the results is heavily dependent on various aspects such as weather conditions, information on the inspected WTB, damage history, etc. In this work, a section of a used WTB is simulated using finite-element modelling (FEM) as well as experimentally tested for evaluating the accuracy of the model. Such a model will provide insight into the potential thermal response of a certain structure (with specific material properties) in given weather (boundary) conditions. The model is able to provide satisfactory predictions of the thermal response of the structure, as well as indicate what thermal contrast(s) result from artificial defects introduced in the structure.
Recently, the photothermal determination of the thermophysical properties of concrete under lab conditions was reported. Their values are mainly needed to look at the energy consumption of buildings. Additionally, changes in their values in relation to the initial state might also be a good indicator for material quality or for moisture. The present contribution explains the photothermal method in a more general way to indicate the potential for on-site application. Secondly, a special application case is regarded: the detection of moisture in concrete. Two concrete samples were soaked with water, followed by a drying period, to obtain different levels of water penetration. The water contents were determined by weighing, and the photothermal response was measured. The results show a large influence on the measured temperature transients, which is larger than expected from the original simple model. They clearly provide two points: the photothermal method is suited to detect moisture in concrete, but the magnitude of the actual measurement effect is not yet understood.
Additive manufacturing (AM) technologies, generally called 3D printing, are widely used because their use provides a high added value in manufacturing complex-shaped components and objects. Defects may occur within the components at different time of manufacturing, and in this regard, non-destructive techniques (NDT) represent a key tool for the quality control of AM components in many industrial fields, such as aerospace, oil and gas, and power industries. In this work, the capability of active thermography and eddy current techniques to detect real imposed defects that are representative of the laser powder bed fusion process has been investigated. A 3D complex shape of defects was revealed by a μCT investigation used as reference results for the other NDT methods. The study was focused on two different types of defects: porosities generated in keyhole mode as well as in lack of fusion mode. Different thermographic and eddy current measurements were carried out on AM samples, providing the capability to detect volumetric irregularly shaped defects using non-destructive methods.
The knowledge of the thermal parameters of a particular concrete is essential for thermal design of a building, but also could help to identify and assess the state of a concrete structure. Active thermography has the potential to be applied onsite and to provide a fast investigation of thermal properties. In this work, three different concrete samples were investigated by active thermography in reflection and in transmission setup. It was found that this method yields the same results without direct contact as the Transient Plane Source (TPS) method as an established inspection tool.
Active thermography is a fast, contactless and non-destructive technique that can be used to detect internal defects in different types of material. Volumetric irregularities such as the presence of pores in materials produced by the Additive Manufacturing processes can strongly affect the thermophysical and the mechanical properties of the final component.
In this work, an experimental investigation aimed at detecting different pores in a sample made of stainless AISI 316L produced by Laser Powder Bed Fusion (L-PBF) was carried out using pulsed thermography in reflection mode. The capability of the technique and the adopted setups in terms of geometrical and thermal resolution, acquisition frequency and energy Density of the heating source were assessed to discern two contiguous pores as well as to detect a single pore. Moreover, a quantitative indication about the minimum resolvable pore size among the available and analysed defects was provided. A powerful tool to assess the Limits and the opportunities of the pulsed technique in terms of detectability and localizability was provided by comparing active thermography results to Computed Tomography as well as a related Finite Element Analysis (FEA) to simulate the pulsed heating transfer with Comsol.
Polymerbeschichtungen auf Beton bieten einerseits mechanischen Schutz vor Beschädigungen und verhindern das Eindringen von Wasser, gelösten Salzen und CO2 und können andererseits der Oberfläche ein gewünschtes Aussehen geben. Daher werden sie in der Bauindustrie insbesondere bei Brücken und Parkhäusern häufig verwendet. Für die beabsichtigte Wirkung der Beschichtung ist deren Schichtdicke ein entscheidender Faktor und muss daher nach Aufbringung der Schicht und im Betrieb regelmäßig überprüft werden. Üblich sind hier zerstörende Verfahren mit nachträglich erforderlicher Ausbesserung. Im Rahmen eines Vorgängerprojektes wurde an der BAM in Kooperation mit der IBOS GmbH ein zerstörungsfreies Verfahren entwickelt, welches auf aktiver Thermografie basiert. Ein Prototyp mit Halogenlampe und Infrarot-Kamera wurde erprobt.
Das hier beschriebene Folgeprojekt hat das Ziel, dieses Verfahren zu standardisieren, damit es sich in der Industrie als zerstörungsfreies Alternativverfahren zur Schichtdickenbestimmung durchsetzt. Im ersten Schritt wird gezeigt, bei welchen Oberflächenschutzsystemen das Verfahren bereits zuverlässige Schichtdickenmessungen ermöglicht und praxistauglich ist. Anschließend werden weitere Forschungsthemen definiert und bearbeitet, die eine Anwendung für alle Oberflächenschutzsysteme ermöglichen sollen. Besondere Herausforderungen stellen etwa Sandeinstreuungen in der Polymerschicht dar. Auch muss der Frage nach der Anwendbarkeit auf Mehrschichtsysteme nachgegangen werden. Des Weiteren stellt sich die Frage nach dem Einfluss der Beschaffenheit des Betonuntergrunds auf die Anwendbarkeit des Verfahrens. Im zu erarbeitenden Normentwurf sollen diese Untersuchungen die Möglichkeiten, aber auch die Grenzen der aktiven Thermografie zur Schichtdickenmessung von Oberflächenschutzsystemen aufzeigen. Im Beitrag werden die systematischen Untersuchungen bezüglich dieser Fragestellungen dargelegt.
Sandwich-Schalenstrukturen in situ charakterisiert mit Thermographie und Felddehnungsmessungen
(2018)
An der BAM wurde ein Schalenprüfstand entwickelt, mit dem typische Sandwichschalenstrukturen unter simulierter Betriebsbeanspruchung belastet werden können. Im mechanischen Ermüdungsversuch wurden in situ die Entstehung von Schäden in Schalenprüfkörpern mit Test-Imperfektionen mittels der passiven Thermographie und Felddehnungsmessungen verfolgt. Damit konnten der Zeitpunkt, der Schadensursprung und der Schadensfortschritt zerstörungsfrei bestimmt werden. Zudem wurden vergleichend Schalenprüfkörper mit Luftultraschall und der Röntgen-Laminographie untersucht. Im Rahmen eines BMWi-Forschungsvorhabens wurden die Schädigungsmechanismen evaluiert und Empfehlungen für die Praxis der Fertigung von Rotorblättern abgeleitet. In diesem Beitrag wird sich auf die Darstellung der ZfP-Verfahren und der ZfP-Ergebnisse konzentriert.
Quantification of impact damages in CFRP and GFRP structures with thermography and ultrasonics
(2018)
The extent of damage caused by impacts in fibre reinforced composites depends on the energy of the impacts, on the velocity and the shape of the impacting body, on the material and structure of the composite and on the geometry of the structure. Here, mainly the thickness of the component is essential. The non-destructive evaluation of these damages can be carried out using both ultrasound and active thermography methods. A comparison of the detection sensitivity of these methods for the different damages is carried out in this paper depending on the fibre composite material used (CFRP and GFRP), the thickness of the material and the impact energy. The NDT methods used after the damage are supplemented by thermographic measurements with high temporal resolution, which were already recorded during the impact.
Systematic errors in the evaluation of uncorrected data from thermographic lock-in measurements
(2018)
Lock-in thermography (LT) is based on the correct evaluation of phase differences between the temperature oscillations at different surface regions of the object under test during periodic heating. Since the usual heating procedures contain a DC component, the actual heating pattern achieved is not harmonic. This causes systematic deviations when phase differences are determined by means of harmonic analysis, e.g. with FFT analysis. The resulting errors depend clearly on the ratio between DC and AC amplitude, which is demonstrated at simulated and experimentally recorded temperature transients. Further experimental LT data obtained by different oscillating energy inputs showed a variety of possible shapes of transients with different DC components.
In order to test their suitability different non-destructive methods were performed to inspect a GFRP plate with artificial defects. These defects were manufactured by means of thin PTFE sheets inserted between two plies in three different depth. The inspection methods were microwave reflection, flash thermography and phased array ultrasonics, all applied to the same specimen. Selected results are shown for all methods demonstrating opportunities and limits of the particular inspection methods. The achieved detection limits and further application aspects are compared directly to provide a useful information for the planning of inspection tasks.