Wissenschaftliche Artikel der BAM
Filtern
Dokumenttyp
Schlagworte
- Laser beam welding (25)
- Additive manufacturing (23)
- Welding (14)
- Microstructure (11)
- Additive Manufacturing (10)
- Hydrogen (10)
- Mechanical properties (10)
- Laser powder bed fusion (9)
- Residual stress (9)
- Residual stresses (9)
- Solidification cracking (8)
- Friction (7)
- Tribology (7)
- Ultrasonic-assisted milling (7)
- Wear (7)
- Creep-resistant steel (6)
- Laser metal deposition (6)
- Process monitoring (6)
- Thermography (6)
- Fatigue (5)
- Resistance spot welding (5)
- Surface integrity (5)
- TIG welding (5)
- AFM (4)
- AISI 316L (4)
- Diffusible hydrogen (4)
- Hardness (4)
- Heat accumulation (4)
- High-strength steel (4)
- Hybrid laser arc welding (4)
- Hybrid laser-arc welding (4)
- L-PBF (4)
- Laser Powder Bed Fusion (4)
- Neutron diffraction (4)
- Numerical modeling (4)
- Selective laser melting (SLM) (4)
- Stress relief cracking (4)
- Thick-walled steel (4)
- AGIL (3)
- Alloy 36 (3)
- Artificial neural network (3)
- Atomic force microscopy (3)
- DED (3)
- Deep penetration (3)
- Fatigue crack propagation threshold (3)
- Fatigue tests (3)
- Heat treatment (3)
- High entropy alloy (3)
- Hydrogen embrittlement (3)
- In situ measurement (3)
- In situ monitoring (3)
- Inconel 718 (3)
- Infrared thermography (3)
- LIBS (3)
- Laser powder bed fusion (L-PBF) (3)
- Mechanical Engineering (3)
- Numerical modelling (3)
- Polymers (3)
- Post weld heat treatment (3)
- Quality assurance (3)
- Steel (3)
- Submerged arc welding (3)
- Ti-6Al-4V (3)
- Tubular X-joints (3)
- Varestraint test (3)
- Weld pool shape (3)
- 316L (2)
- AISI 304L (2)
- Additive manufacturing (AM) (2)
- Alloy modification (2)
- Austenite-to-martensite transformation (2)
- Bragg-edge imaging (2)
- Bulge effect (2)
- Chemical composition (2)
- Computed Tomography (2)
- Computed tomography (2)
- Contact resonance (2)
- Crack (2)
- Cracking (2)
- Critical strain (2)
- Crystallographic texture (2)
- Cyclic R-curve (2)
- Data preparation (2)
- Debye–Waller factor (2)
- Deuterium (2)
- Diffusion (2)
- Directed Energy Deposition (2)
- Distortion (2)
- EBSD (2)
- Electron backscattered diffraction (2)
- Finite element simulation (2)
- Force-distance curves (2)
- Fracture (2)
- Full penetration (2)
- GMA welding (2)
- Gap bridgeability (2)
- Gas metal arc welding (2)
- Gas tungsten arc welding (GTAW) (2)
- Grain refinement (2)
- Hardmetal (2)
- Heat control (2)
- High strength steels (2)
- High-entropy alloy (2)
- High-power laser beam welding (2)
- High-strength structural steel (2)
- Hot cracking (2)
- Hot stamping (2)
- Hydrogen Embrittlement (2)
- Hydrogen assisted cracking (2)
- Hydrogen-assisted cracking (2)
- Implant test (2)
- Inter layer time (2)
- LPBF (2)
- Laser beam melting (LBM) (2)
- Laser energy distribution (2)
- Laser hybrid welding (2)
- Laser-metal-deposition (2)
- Liquid metal embrittlement (2)
- Low transformation temperature (LTT) steel (2)
- Lubricants (2)
- Machining (2)
- Mechanics of Materials (2)
- Medium entropy alloy (2)
- Metals and Alloys (2)
- Microstructure characterization (2)
- Neutron imaging (2)
- Neutron radiography (2)
- Niobium carbide (2)
- Niobium carbide (NbC) (2)
- Numerical process simulation (2)
- Numerical simulation (2)
- Offshore (2)
- Optical flow (2)
- Pipeline steel (2)
- Plasma-transferred arc welding (2)
- Porosity (2)
- Post-weld heat treatment (2)
- Preheating (2)
- Ray tracing (2)
- Refill friction stir spot welding (2)
- Representative specimens (2)
- Residual Stress (2)
- Residual stress analysis (2)
- SSRT (2)
- Selective Laser Melting (2)
- Selective Laser Melting (SLM) (2)
- Simulation (2)
- Single pass welding (2)
- Software (2)
- Surface modification (2)
- Technical crack detection (2)
- Tensile properties (2)
- Texture (2)
- Thermal history (2)
- ToF-SIMS (2)
- Tool wear (2)
- Tribologie (2)
- WAAM (2)
- Weld pool dynamics (2)
- Wire arc additive manufacturing (2)
- X-ray diffraction (2)
- i-TRIBOMAT (2)
- 100Cr6 (AISI 52100) steel (1)
- 2101 duplex stainless steel (1)
- 3D Scanning (1)
- 3D printing (1)
- 9% Ni Steel (1)
- 9%Ni steel (1)
- AC magnetic field (1)
- AHSS (1)
- AM feature integration (1)
- ASTM E647 (1)
- Abdichtbauwerk (1)
- Accoustic emission (1)
- Additive Manufacturing (AM) (1)
- Additives (1)
- Advanced high strength steels (1)
- Advanced high-strength steel (1)
- Aging (1)
- AlMg0.7SiTiB filler wire (1)
- AlSi10Mg (1)
- AlSi10Mg alloy (1)
- Alite (1)
- Alkyd resin-based coating (1)
- Aluminum alloys (1)
- Aluminum bronze (1)
- Analytical calculation (1)
- Applications (1)
- Artificial Intelligence (1)
- Artificial intelligence (1)
- As-built LPBF IN718 alloy (1)
- Atomic force microscope (1)
- Austenitic stainless steels (1)
- Automated arc welding (1)
- Automated manufacturing (1)
- Automotive (1)
- Backlight (1)
- Bainitischer Schmiedestahl (1)
- Bauteilauslegung (1)
- Bayesian technique (1)
- Bead-on-plate welds (1)
- Beam oscillation (1)
- Bending test (1)
- Betriebsfestigkeit (1)
- Binders (1)
- Bismuth titanates (1)
- Bohrlochsonde (1)
- Bruchmechanik (1)
- Bulge formation (1)
- Bulging (1)
- Bulging effects (1)
- CFD model (1)
- Cantilever microprobe (1)
- Carbide (1)
- Carbon (1)
- Carbon dioxide footprint (1)
- Carbon steel (1)
- Catalysis (1)
- Cellular substructure (1)
- Cermet (1)
- Characterisation (1)
- Characterization (1)
- Characterization of corrosion layers (1)
- Charakterisierung (1)
- Charpy impact toughness (1)
- Chunky graphite (1)
- Cimensional Accuracy (1)
- Circumferential weld (1)
- Clinker substitute (1)
- Clustering (1)
- Co-Cr-alloy (1)
- Cobalt-chromium alloy (1)
- Cold cracking (1)
- Cold cracking safety (1)
- Columnar crystal growth (1)
- Component test (1)
- Component-like test (1)
- Composites (1)
- Computed tomography (CT) (1)
- Computer vision (1)
- Condensed Matter Physics (1)
- Condition monitoring (1)
- Convolutional neural network (1)
- Convolutional neural networks (CNN) (1)
- Core-shell structures (1)
- Corrosion (1)
- Crack closure effect (1)
- Crack-tip constraint (1)
- Creep (1)
- Creep behavior (1)
- Creep-resisting materials (1)
- Critical strain rate (1)
- Cryogenic steel (1)
- Cryogenic temperature (1)
- Crystal branch development (1)
- Crystal plasticity (1)
- Cutting forces (1)
- Cutting tool (1)
- Cyclic loading (1)
- Cylindrical turning (1)
- DED-EB (1)
- DED-arc (1)
- Damage prediction (1)
- Damage tolerance (1)
- Data evaluation methods (1)
- Data fusion (1)
- Data-driven quality assurance (1)
- Debye-Waller-Faktor (1)
- Deep learning (1)
- Deep penetration laser beam welding (1)
- Defect detection (1)
- Defects (1)
- Dental materials (1)
- Dichtungen (1)
- Diffraction (1)
- Diffraction-elastic constants (1)
- Diffusion/diffusivity (1)
- Digital Image Correlation (1)
- Digital image correlation (1)
- Digitalisation (1)
- Digitalization (1)
- Direct laser deposition (1)
- Directed energy deposition (1)
- Dislocation density (1)
- Dispersive XAS (1)
- Displacement (1)
- Dissimilar joints (1)
- Dissimilar materials (1)
- Dissimilar metal weld (1)
- Distortion upon baseplate removal (1)
- Ditigtal image correlation (1)
- Dual phase steel (1)
- Duplex AISI 2205 (1)
- Duplex stainless steel (1)
- Duplex stainless steels (1)
- Duplex steels (1)
- Dwell-time (1)
- EBAM (1)
- Edge quality (1)
- Effect of scanning strategies (1)
- Elastic modulus (1)
- Elastomers (1)
- Electrochemical permeation (1)
- Electromagnetic backing (1)
- Electromagnetic field (1)
- Electromagnetic forces (1)
- Electromagnetic stirring (1)
- Electromagnetic weld pool support (1)
- Electromagnetic weld pool support system (1)
- Electron backscatter diffraction (1)
- Electron beam welding (1)
- Electron microscopy (1)
- Element transport (1)
- Embedded electronics (1)
- Emisssivity (1)
- End crater (1)
- Endurance limit (1)
- Energy Engineering and Power Technology (1)
- Environmental conditions (1)
- Environmental impact categories (1)
- Error sources analysis (1)
- Evaporation (1)
- Experimental determination (1)
- Experimental procedure (1)
- FAIR data (1)
- FAT class (1)
- FEM (1)
- Fatigue Strength (1)
- Fatigue damage (1)
- Fatigue life (1)
- Fatigue limit (1)
- Fatigue properties (1)
- Femtosecond laser (1)
- Femtosecond laser processing (1)
- Ferritic spheroidal graphite cast iron (1)
- Ferroelectricity/ferroelectric materials (1)
- Filler material distribution (1)
- Filler wire (1)
- Filler wire mixing (1)
- Finish milling (1)
- Finite Element Method (1)
- Finite element (FE) (1)
- Finite element analysis (1)
- Finite element method (1)
- Finite element method (FEM) (1)
- Flange width (1)
- Flaw detection (1)
- Flüssigmetallinduzierte Rissbildung (1)
- Formation (1)
- Fractography (1)
- Fracture Mechanics (1)
- Frequency domain (1)
- Frequenzanalyse (1)
- Friction stir welding (1)
- Fuel Technology (1)
- Fusion zone size (1)
- Galvanized steel (1)
- General analytical solutions (1)
- Geteilte Infrastruktur (1)
- Green Deal (1)
- HAZ-softening (1)
- HCF (1)
- HSLA steel (1)
- Hard metals (1)
- Hardly separable problem (1)
- Harmonisation (1)
- Hastelloy X (1)
- Heat Treatment (1)
- Heat source models (1)
- Heat-affected zone (1)
- High power laser beam welding (1)
- High process speeds (1)
- High strength steel (1)
- High-entropy alloys (1)
- High-pressure hydrogen environment (1)
- High-strength filler metals (1)
- High-strength steel filler metal (1)
- High-strength steels (1)
- Hochfester Stahl (1)
- Hollow Specimen Technique (1)
- Hollow specimen (1)
- Hollow specimen technique (1)
- Hot Cracks (1)
- Hot cracking test (1)
- Hot tensile test (1)
- Hot working tool steel (1)
- Hybrid Laser arc Welding (1)
- Hybrid repair (1)
- Hydraulic reactivity (1)
- Hydrogen Transfer Film (1)
- Hydrogen diffusion (1)
- Hydrogen measurement (1)
- IBESS (1)
- IBESS Approach (1)
- IN 718 (1)
- IN725 (1)
- ISO 12108 (1)
- Image processing (1)
- Image registration (1)
- Impact Absorbed Energy (1)
- Implants (1)
- In situ (1)
- In-situ process monitoring (1)
- In-situ tensile test (1)
- Inconel 625 (1)
- Industrial and Manufacturing Engineering (1)
- Instumented indentation test (1)
- Integrated alignment features (1)
- Intelligent tribological material characterization (1)
- Intelligente tribologische Werkstoffcharakterisierung (1)
- Inter-layer time (1)
- Interoperability (1)
- Iron aluminide (1)
- Joining dissimilar materials (1)
- Joining technology (1)
- Kernel average misorientation (1)
- Keyhole collapse (1)
- Keyhole dynamics (1)
- Kitagawa-Takahashi diagram (1)
- L-PBF IN718 material (1)
- LCF (1)
- LIBS TIG welding (1)
- LMD (1)
- LTT Weld Filler Materials (1)
- LTT filler metal (1)
- LTT weld filler materials (1)
- Lab-to-field up-scaling (1)
- Lab-to-field upscaling (1)
- Lack-of-fusion (1)
- Lamé curves (1)
- Large-scale test (1)
- Laser Metal Deposition (LMD) (1)
- Laser Powder Bed Fusion (L-PBF) (1)
- Laser Powder Bed Fusion (LPBF) (1)
- Laser Powder Bed Fusion (PBF-LB/M, L-PBF) (1)
- Laser Welding (1)
- Laser beam melting (1)
- Laser cutting (1)
- Laser energy absorption (1)
- Laser implantation (1)
- Laser metal deposition (LMD) (1)
- Laser powder-based directed energy deposition (1)
- Laser welding (1)
- Laser-based additive manufacturing (1)
- Laser-induced oxide layer (1)
- Laser-induced periodic surface strctures (LIPSS) (1)
- Laser-induced periodic surface structures (LIPSS) (1)
- Laser-plasma hybrid (1)
- Lead-free ceramics (1)
- Life cycle assessment (1)
- Lifetime (1)
- Liquid Metal Embrittlement (1)
- Liquid phase sintering (1)
- Local Weld Geometry (1)
- Local critical strain (1)
- Local fatigue approaches (1)
- Local fatigue spproaches (1)
- Localized laser dispersing (1)
- Lorentz force (1)
- Lorentz forces (1)
- Low-cycle fatigue (1)
- L‐PBF (1)
- MVT (1)
- MWIR (1)
- Machine learning (1)
- Machine vision (1)
- Magnesium Alloy (1)
- Magnesium alloy (1)
- Magnetic bath support (1)
- Magnetic field (1)
- Martensite (1)
- Matching ferritic filler metal (1)
- Materials database (1)
- Mechanical anisotropy (1)
- Mechanical mismatching (1)
- Mechanical property (1)
- Melt pool depth (1)
- Melt pool dynamics (1)
- Metal (1)
- Metal mixing (1)
- Microalloying influences (1)
- Microbiologically influenced corrosion (1)
- Microcracking (1)
- Microfocus X-ray computer tomography (μCT) (1)
- Mild steels (1)
- Minimum Waiting Time (1)
- Mining head gear (1)
- Misalignment of edges (1)
- Model calibration (1)
- Model order reduction (1)
- Modellierung (1)
- Modelling studies (1)
- Modification of structural morphology (1)
- Molten pool (1)
- Multi-materials joining (1)
- Multi-physical modelling (1)
- Multi-principal element alloy (1)
- Multi-principal element alloys (1)
- Multiple principal element alloy (1)
- Multiple reflections (1)
- NIR (1)
- Nanotribology (1)
- Nanowear (1)
- Natural silver wires (1)
- Near-surface X-ray diffraction (1)
- Neutron Diffraction (1)
- Neutron and X-ray diffraction (1)
- Ni alloy (1)
- Ni-based austenitic filler metal (1)
- Nickel (1)
- Notch stress approach (1)
- Novel metrology (1)
- Numerical Simulation (1)
- Numerical investigation (1)
- Numerical welding simulations (1)
- Offshore steel grade (1)
- Online Process Monitoring (1)
- Online monitoring (1)
- Open science (1)
- Open source (1)
- Optical Tomography (1)
- Optical tomography (1)
- Oscillating ball-on-disc test (1)
- Oscillating magnetic field (1)
- Oscillating vapor plume (1)
- Oxidation (1)
- PBF-LB/M (1)
- PBF-LB/M/316L (1)
- Parabolic flight (1)
- Partial penetration (1)
- Particle transfer (1)
- Path planning (1)
- Peak stress method (1)
- Peak stress method (PSM) (1)
- Penetration depth (1)
- Periodic solidification pattern (1)
- Piezoresistive (1)
- Piezoresistive cantilever (1)
- Pipe weld preparation (1)
- Plasma cutting (1)
- Plasma-cut samples (1)
- Plasma-transferred-arc (1)
- Plastic deformation (1)
- Polymer (1)
- Polymere (1)
- Polyurethan (1)
- Position detection (1)
- Post Weld Heat Treatment (PWHT) (1)
- Potential drop technique (1)
- Potentiodynamic measurements (1)
- Ppreheating temperature (1)
- Precipitation hardening aluminum alloys (1)
- Pressure-dependent solubility (1)
- Prevention (1)
- Probabilistic assessment (1)
- Process chain (1)
- Process simulation (1)
- Projekt AGIL - Alterung additiv gefertigter metallischer Materialien und Komponenten (1)
- Proper generalized decomposition (1)
- Properties (1)
- Prostheses (1)
- Pulsed laser beam welding (1)
- Quality monitoring (1)
- Ray teacing (1)
- Ray-tracing methods (1)
- Reactor conditions (1)
- Reference data (1)
- Reference standards (1)
- Refraction (1)
- Renewable Energy, Sustainability and the Environment (1)
- Repair welding (1)
- Repair-welding (1)
- Research data management (1)
- Residual Stresses (1)
- Residual stress in AM (1)
- Residual stress state (1)
- Ripples (1)
- Rissbildung in Stahl (1)
- Roughness (1)
- S-N curve (1)
- S-Phase (1)
- SEM (1)
- SIMS (1)
- SLM printed plasma torch (1)
- SWIR (1)
- SWIR thermography (1)
- Sample random results (1)
- Scan strategy influence (1)
- Scanning kelvin probe force microscopy (1)
- Scattering (1)
- Schallemission (1)
- Seam geometry (1)
- Selective laser beam melting (1)
- Selektive-laser-melting (1)
- Shared infrastruture (1)
- Shear modulus (1)
- Ship building (1)
- Shipbuilding steel (1)
- Sicherheit (1)
- Single asperity (1)
- Single asperity contact (1)
- Single-pass welding (1)
- Sliding wear (1)
- Small-scale specimens (1)
- Solidification (1)
- Solubility (1)
- Spark plasma sintering (1)
- Stainless Steel (1)
- Stainless steel (1)
- Stainless steels (1)
- Staircase method (1)
- Statistical analysis (1)
- Steel and aluminium (1)
- Steelmaking slag (1)
- Stochastic sample functions (1)
- Strain fields prediction (1)
- Strain measurement (1)
- Strain-free lattice references (1)
- Strain-free lattice spacing (1)
- Stress Relief Cracking (SRC) (1)
- Stress balance (1)
- Stress balance condition (1)
- Structural stress approach (1)
- Structure analysis (1)
- Sub-oxide (1)
- Supermartensitic steel (1)
- Surface Integrity (1)
- Surface preparation (1)
- Surface processing (1)
- Surface structures (1)
- Synchrotron radiation (1)
- TEKKEN (1)
- Temperature (1)
- Temperature dependence (1)
- Tensile Strength (1)
- Tensile loading (1)
- Tensile resistance spot welding experiment (1)
- Tensile strength (1)
- Tensile testing (1)
- Thermal analysis (1)
- Thermal cycles (1)
- Thermodynamic modelling (1)
- Thermodynamic simulation (1)
- Thick materials (1)
- Thick plate welding (1)
- Thick-plate welding (1)
- Thick-walled (1)
- Titanium (1)
- Trapping (1)
- Tribo-Analytik (1)
- Tribo-analytics (1)
- Tungsten carbide (WC) (1)
- Two-dimensional solidification (1)
- Two-run welding technique (1)
- UV-blocker addition (1)
- Ultraschall-Echoverfahren (1)
- Ultraschall-Messtechnik (1)
- Ultrasonic Assisted Machining (1)
- Ultrasonic machining (1)
- Upscaling (1)
- V-notch impact toughness (1)
- Vaporization (1)
- Varestraint testing (1)
- Verschlussbauwerk (1)
- WRC 1992 diagram (1)
- Wear particles (1)
- Weathering tests (1)
- Weld metal cracking (1)
- Weld pool (1)
- Weldability (1)
- Welded Joints (1)
- Welded joint (1)
- Welded joints (1)
- Welding Simulation (1)
- Welding simulation (1)
- Welding thermal cycle (1)
- Weldx (1)
- Werkstoffdatenbank (1)
- White light interferometry (1)
- Widerstandspunktschweißen (1)
- Wind energy (1)
- Wire electron beam additive manufacturing (1)
- Wire feed laser beam welding (1)
- Wire-based additive manufacturing (1)
- X-ray Diffraction (1)
- X-ray and Neutron Diffraction (1)
- X-ray and neutron diffraction (1)
- X-ray computed tomography (XCT) (1)
- X-ray refraction (1)
- Young's modulus (1)
- Zero wear (1)
- Zerstörungsfreie Prüfung (1)
- Zink (1)
- contact resonance (1)
- infrared Thermography (1)
- µ-gravity (1)
- µCT (1)
- µCT-analysis (1)
- μCT-analysis (1)
Organisationseinheit der BAM
- 9 Komponentensicherheit (215) (entfernen)
Paper des Monats
- ja (9)
Co-Cr alloys are frequently used for highly stressed components, especially in turbine and plant construction, due to their high resistance to thermal and mechanical stress, as well as to corrosive and abrasive loads. Furthermore, they are classified as difficult-to-cut materials because of their high strength and toughness as well as their low thermal conductivity. However, for Co, an increased cost and supply risk can be observed in recent years. Therefore, additive manufacturing (AM) offers significant economic advantages due to higher material efficiency regarding repair, modification, and manufacturing of such components. Concerning inhomogeneity and anisotropy of the microstructure and properties as well as manufacturing-related stresses, a lot of knowledge is still necessary for the economic use of additive welding processes in SMEs. In addition, subsequent machining, particularly contour milling, is essential to generate the required complex contours and surfaces. Hence, additive and machining manufacturing processes need to be coordinated in a complementary way, especially due to additional challenges arising in milling of heterogeneous hard-to-cut microstructures. Recently, it has been shown that modern, hybrid cutting processes, such as ultrasonic-assisted milling (US), can improve the cutting situation. In this investigation, the Co-Cr initial alloy is additionally modified with Ti and Zr up to 1 wt% with the aim to enhance the homogeneity of the microstructure and, thus, the machinability. Hence the investigation includes finish milling tests of the AM components and the comparison of US and conventional machining. Both the modifications and the ultrasonic assistance exhibit a significant effect on the machining situation; for example US causes a higher surface integrity of the finish milled surfaces compared to conventional milling.
An accurate and efficient description of the spatial distribution of laser energy is a crucial factor for the modeling of laser material processing, e.g., laser welding, laser cutting, or laser-based additive manufacturing. In this study, a 3D heat transfer and fluid flow model coupled with the volume-of-fluid algorithm for free surface tracking is developed for the simulation of molten pool dynamics in high-power laser beam welding. The underlying laser-material interactions, i.e., the multiple reflections and Fresnel absorption, are considered by a raytracing method. Two strategies of free surface reconstruction used in the ray-tracing method are investigated: a typical piecewise linear interface calculation (PLIC)-based method and a novel localized level-set method. The PLIC-based method is discrete, resulting in noncontinuous free surface reconstruction. In the localized level-set method, a continuous free surface is reconstructed, and, thus, the exact reflection points can be determined. The calculated spatial laser energy distribution and the corresponding molten pool dynamics from the two methods are analyzed and compared. The obtained numerical results are evaluated with experimental measurements to assure the validity of the proposed model. It is found that distinct patterns of the beam multiple reflections are obtained with the different free surface reconstructions, which shows significant influence not only on the molten pool behaviors but also on the localized keyhole dynamics.
Motivated by the loss of tensile strength in 9%Ni steel arc-welded joints performed using commercially available Ni-based austenitic filler metals, the viability of retaining tensile strength using an experimentally produced matching ferritic filler metal was confirmed. Compared to the austenitic Ni-based filler metal (685 MPa), higher tensile strength in gas metal arc (GMA) welded joints was achieved using a ferritic filler metal (749 MPa) due to its microstructure being similar to the base metal (645 MPa). The microstructure of hard martensite resulted in an impact energy of 71 J (-196 °C), which was two times higher than the specified minimum value of _>34 J. The
tensile and impact strength of the welded joint is affected not only by its microstructure, but also by the degree of its mechanical mismatch depending on the type of filler metal. Welds with a harder microstructure and less mechanical mismatch are important for achieving an adequate combination of tensile strength and notched impact strength. This is achievable with the cost-effective ferritic filler metal. A more desirable combination of mechanical properties is guaranteed by applying low preheating temperature (200 °C), which is a more practicable and economical solution compared to the high post-weld heat treatment (PWHT) temperature (580 °C) suggested by other research.
Martensitic 9% Cr steels like P91 and P92 can show an increased susceptibility to delayed hydrogen-assisted cracking. The focus of this study was the microstructure and heat treatment efect on the mechanical properties of P92 base material and P91 multi-layer weld metal in both as-welded and post weld heat treated (PWHT) condition. Tensile tests with hydrogen free reference samples and electrochemically hydrogen charged samples were carried out; the mechanical properties were assessed and supported by detailed fractographic analysis. Finally, a hydrogen and microstructure-dependent fracture criterion is established. All investigated microstructures showed a hydrogen-infuenced degradation of the mechanical properties compared to the hydrogen-free reference samples. The as-welded martensitic P91 weld metal had the highest degree of degradation in the presence of hydrogen. The P91 PWHT weld metal and the P92 base material had comparable properties. From that point of view, a signifcantly increased risk for hydrogen-assisted cold cracking during welding fabrication of P91 weld joints must be considered before any heat treatment is conducted.
Due to the rapidly increasing price of tungsten carbide and the significant health risks associated with the wear products of WC-Co (Co3O4 and Wo3), an alternative is required. Niobium carbide (NbC) is well suited as a cutting tool due to its high melting point and low solubility in iron. So far, NbC-Ni cermets best met the requirements of high hardness and toughness. Various secondary carbides such as VC, Mo2C, TiC, but also WC were added to further improve the hardness.
The study deals with the influence of the heat input and the resulting cooling times on the microstructure and Charpy impact toughness of single-pass laser hybrid welded 20-mm thick high-strength steel S690QL. The main focus is on the change of the mechanical properties over the entire seam thickness. The cooling times were measured in-situ using a pyrometer and an optical fibre in three different depths of the seam where Charpy impact test specimens were also later taken. Thereby, three different heat inputs from 1.3 kJ/mm to 2 kJ/mm were investigated. Despite the observed decreased values of both t8/5-cooling time and the Charpy impact toughness in the root part of the seam, the required impact toughness of 38 J/cm2 could be reached in dependance on applied heat input, especially at the heat input of 1.6 kJ/mm.
Solidification cracking is still a serious problem in laser beam welding, especially in the welding of thick-walled plates. The influence of weld pool geometry on solidification cracking in partial penetration welding of thick plates is investigated within scope of this study. Therefore, a specific experimental setup of steel and quartz glass in butt configuration and on the side with high-speed camera were used to record the weld pool shape. In addition, the influence of laser inclination angle on the weld pool geometry and on solidification crack formation was investigated. The results show a bulge in the weld pool root, which is separated from an upper region by a necking region. This leads to a case where there are three different longitudinal region lengths with different solidification zones. This temporal sequence of solidification strongly promotes the formation of solidification cracks in the weld root.
Influence of a 265 °C heat treatment on the residual stress state of a PBF-LB/M AlSi10Mg alloy
(2022)
Laser Powder Bed Fusion (PBF-LB/M) additive manufacturing (AM) induces
high magnitude residual stress (RS) in structures due to the extremely heterogeneous cooling and heating rates. As the RS can be deleterious to the fatigue resistance of engineering components, great efforts are focused on understanding their generation and evolution after post-process heat treatments. In this study, one of the few of its kind, the RS relaxation induced in an as-built PBF-LB/M AlSi10Mg material by a low-temperature heat treatment (265 °C for 1 h) is studied by means of X-ray and neutron diffraction. Since the specimens are manufactured using a baseplate heated up to 200 °C, low RS are found in the as-built condition. After heat treatment a redistribution of the RS is observed, while their magnitude remains constant. It is proposed that the redistribution is induced by a repartition of stresses between the a-aluminium matrix and the silicon phase, as the morphology of the silicon phase is affected by the heat treatment. A considerable scatter is observed in the neutron diffraction RS profiles, which is principally correlated to the presence (or absence) of pockets of porosity developed at the borders of the chessboard pattern.
In the framework of the fatigue assessment of welded components, several methods are available in design standards such as the nominal stress, hot-spot stress, notch stress and linear elastic fracture mechanics approaches. The present paper aims at comparing two advanced local approaches for the fatigue strength assessment of different welded joints made of steel. The first one is IBESS which is based on short crack fracture mechanics. The second one is the PSM which instead involves the strain energy density approach. Both methods will be briefly presented, and the fatigue life prediction results discussed. The results obtained for the joint geometries considered in this work show advantages and drawbacks of the approaches, which are thoroughly analysed as well.
Study on the transition behavior of the bulging effect during deep penetration laser beam welding
(2022)
The present work is devoted to the study of the transition behavior of the recently confirmed widening of the weld pool, known as the bulging effect, during high-power deep penetration laser beam welding of thick unalloyed steel sheets. A three-dimensional transient multi-physics numerical model is developed, allowing for the prediction of the bulge formation and the study of its temporal behavior. The model is generalized to account automatically for the transition from partial to complete penetration. Several experimental measurements and observations, such as drilling period, weld pool length, temperature, efficiency, and metallographic cross-sections are used to verify the model and assure the plausibility of the numerical results. The analysis of the calculated temperature and velocity distributions, as well as the evolution of the keyhole geometry, shows that the formation of a bulging region strongly depends on the penetration depth of the weld. Based on the numerical results, the bulge is found to occur transiently, having its transition from a slight bulge to a fully developed bulging between penetration depths of 6 mm and 9 mm, respectively.
Various test methods are available for assessing the susceptibility of materials to solidification cracking during welding. In the widely used Varestraint test, the crack length is selected as a criterion as a function of the applied bending strain.
Unfortunately, the crack length does not characterize the material behavior alone but depends to varying degrees on the individual test parameters used, which makes the interpretation of the results difficult. In addition, the crack length is not comparable under different test conditions. To overcome these disadvantages, we have developed a novel evaluation methodology that decouples the machine influence from the material behavior. The measured crack length is related to the maximum possible value specified by welding speed and deformation time. This relative crack length is calculated numerically, considering the orientation of the cracks. Experiments on two high-alloy martensitic welding consumables show that, in contrast to the conventional evaluation, a comparison of different welding parameters becomes possible. Furthermore, the strain rate proved to be a suitable crack criterion in agreement with Prokhorov's hot cracking model.
Duplex stainless steels combine the positive properties of its two phases, austenite and ferrite. Due to its good corrosion resistance, high tensile strength, and good ductility, it has multiple applications. But laser beam welding of duplex steels changes the balanced phase distribution in favor of ferrite. This results in a higher vulnerability to corrosion and a lower ductility. Herein, different powder combinations consisting of duplex and nickel for coating layers by laser metal deposition (LMD) are investigated. Afterward, laser tracks are welded, and the temperature cycles are measured. The ferrite content of the tracks is analyzed by feritscope, metallographic analysis, and electron backscatter diffraction. The goal is the development of a powder mixture allowing for a duplex microstructure in a two-step process, where first the edges of the weld partners are coated with the powder mixture by LMD and second those edges are laser beam welded. The powder mixture identified by the pretests is tested in the two-step process and analyzed by metallographic analysis, energy-dispersive X-ray spectroscopy, and
Vickers hardness tests. The resulting weld seams show a balanced duplex microstructure with a homogenous nickel distribution and a hardness of the weld seam similar to the base material.
The Directed Energy Deposition process is used in a wide range of applications including the repair, coating or modification of existing structures and the additive manufacturing of individual parts. As the process is frequently applied in the aerospace industry, the requirements for quality assurance are extremely high. Therefore, more and more sensor systems are being implemented for process monitoring. To evaluate the generated data, suitable methods must be developed. A solution, in this context, was the application of artificial neural networks (ANNs). This article demonstrates how measurement data can be used as input data for ANNs. The measurement data were generated using a pyrometer, an emission spectrometer, a camera (Charge-Coupled Device) and a laser scanner. First, a concept for the extraction of relevant features from dynamic measurement data series was presented. The developed method was then applied to generate a data set for the
quality prediction of various geometries, including weld beads, coatings and cubes. The results were compared to ANNs trained with process parameters such as laser power, scan speed and powder mass flow. It was shown that the use of measurement data provides additional value. Neural networks trained with measurement data achieve significantly higher prediction accuracy, especially for more complex geometries.
size limitations and high production costs of L-PBF make it competitive for smaller, highly complex components, while the less complex elements of an assembly are manufactured conventionally. This leads to scenarios that use L-PBF only where it’s beneficial, and it require an integration and joining to form the final product. For example, L-PBF combustion swirlers are welded onto cast parts to produce combustion systems for stationary gas turbines. Today, the welding process requires complex welding fixtures and tack welds to ensure the correct alignment and positioning of the parts for repeatable weld results. In this paper, L-PBF and milled weld preparations are presented as a way to simplify the Tungsten inert gas (TIG) welding of rotationally symmetrical geometries using integrated features for alignment and fixation. Pipe specimens with the proposed designs are manufactured in Inconel 625 using L-PBF and milling. The pipe assembly is tested and TIG welding is performed for validation. 3D scans of the pipes before and after welding are evaluated, and the weld quality is examined via metallography and computed tomography (CT) scans. All welds produced in this study passed the highest evaluation group B according to DIN 5817. Thanks to good component alignment, safe handling, and a stable welding process, the developed designs eliminate the need for part-specific fixtures, simplify the process chain, and increase the process reliability. The results are applicable to a wide range of components with similar requirements.
As onshore installation capacity is limited, the increase in the number of offshore wind turbines (OWT) is a major goal. In that connection, the OWTs continuously increase in size and weight and demand adequate foundations concepts like monopiles or tripods. These components are typically manufactured from welded mild steel plates with thickness up to 200 mm. The predominant welding technique is submerged arc welding (SAW). In accordance with the standards, the occurrence of hydrogen-assisted cracking is anticipated by either a minimum waiting time (MWT, before non-destructive testing of the welded joint is allowed) at ambient or a hydrogen removal heat treatment (HRHT) at elevated temperatures. The effectiveness of both can be estimated by calculation of the diffusion time, i.e., diffusion coefficients. In this study, these coefficients are obtained for the first time for a thick-walled S420G2+M offshore steel grade and its multi-layer SAW joint. The electrochemical permeation technique at ambient temperature is used for the determination of diffusion coefficients for both the base material and the weld metal. The coefficients are within a range of 1025 to 1024 mm2/s (whereas the weld metal had the lowest) and are used for an analytical and numerical calculation of the hydrogen diffusion and the related MWT. The results showed that long MWT can occur, which would be necessary to significantly decrease the hydrogen concentration. Weld metal diffusion coefficients at elevated temperatures were calculated from hydrogen desorption experiments by carrier gas hot extraction. They are within a range of 1023 mm2/s and used for the characterization of a HRHT dwell-time. The analytical calculation shows the same tendency of long necessary times also at elevated temperatures. That means the necessary time is strongly influenced by the considered plate thickness and the estimation of any MWT/HRHT via diffusion coefficients should be critically discussed.
Influence of Surface Preparation on Cracking Phenomena in TIG-Welded High and Medium Entropy Alloys
(2022)
Multi-element systems with defined entropy (HEA—high entropy alloy or MEA—medium entropy alloy) are rather new material concepts that are becoming increasingly important in materials research and development. Some HEA systems show significantly improved properties or combinations of properties, e.g., the overcoming of the trade-off between high strength and ductility. Thus, the synthesis, the resulting microstructures, and properties of HEA have been primarily investigated so far. In addition, processing is crucial to achieve a transfer of potential HEA/MEA materials to real applications, e.g., highly stressed components. Since fusion welding is the most important joining process for metals, it is of vital importance to investigate the weldability of these materials. However, this has rarely been the subject of research to date. For that reason, in this work, the weldability depending on the surface preparation of a CoCrFeMnNi HEA and a CoCrNi MEA for TIG welding is investigated. The fusion welding of longer plates is described here for the first time for the CoCrNi alloy. The welds of both materials showed distinct formation of cracks in the heat affected Zone (HAZ). Optical and scanning electron microscopy analysis clearly confirmed an intergranular fracture topography. However, based on the results, the crack mechanism cannot be conclusively identified as either a liquid metal embrittlement (LME) or hot cracking-like liquid film separation.
The effect of the environmental conditions on the threshold against fatigue crack propagation
(2022)
The threshold against fatigue crack propagation (ΔKth) is a crucial parameter for the damage tolerance assessment of engineering components subjected to cyclic loading and it is composed by two distinct components, one intrinsic, dependent on the elastic material properties and the lattice type, and one extrinsic, related to the occurrence of crack closure effects. An important issue is that several factors can influence ΔKth and, in general, the fatigue crack propagation behavior. In this work, the influence of the experimental procedure, air humidity, stress ratio and test frequency on da/dN-ΔK data has been investigated. Results are discussed with their potential causes and consequences on the calculations of the residual lifetime.
The Kitagawa-Takahashi (KT) diagram is a proven concept for describing the fatigue limit in presence of a defect or crack. It can be determined empirically with great experimental effort. It can also be estimated by means of the El Haddad relationship if the endurance limit and the long fatigue crack propagation threshold are available in reasonable accuracy. A third option is the determination using the cyclic R-curve, which describes the dependency of the fatigue crack propagation threshold on the crack growth at the short crack propagation stage. This can be experimentally determined using a closure-free initial pre-crack. It can then be applied to the determination of crack arrest for a given applied load and a given defect or crack size. Compared to the other two methods mentioned above, this option has considerable advantages: It can be applied to any component and any stress ratio. It allows the treatment of multiple cracks and provides estimations of the S-N curve in the finite life regime as well as at the endurance limit. Compared to the empirical determination of the KT diagram, the experimental effort is significantly lower and compared to the El Haddad approach it avoids problems such as the use of non-conservative long fatigue crack propagation thresholds (when the conventional load reduction method is applied to materials prone to corrosion) and the mathematical predetermination of the curve shape. The work introduces the method and provides a critical discussion as well as quantitative comparison between the different methods.
Al-Si alloys produced by Laser Powder Bed Fusion (L-PBF) techniques allow the fabrication of lightweight free-shape components that find space in aerospace, automotive, biomedical and military applications. Due to the high cooling rates occurring during the building process, L-PBF AlSi10Mg alloys exhibit an ultra-fine microstructure that leads to superior mechanical properties in the as-built condition compared to conventional cast Al-Si materials. Nevertheless, L-PBF processing induces high thermal gradients, leading to deleterious residual stress levels that must be considered to avoid part distortion and unpredicted failures. In order to relax detrimental residual stress and to increase the ductility, post-processing stress relief treatments are generally performed. In as-built condition the hypoeutectic AlSi10Mg microstructure consist of fine α-Al cells containing uniformly dispersed silicon nanoparticles, which are, in addition, surrounded by a eutectic Si network. Above 260°C the silicon interconnectivity starts to breakdown into spheroidized particles and to coarsen. At the same time, the heating residual stresses are relieved.
The objective of the contribution is to investigate, under different heat treatment conditions, the evolution of microstructure and residual stresses in view of optimizing the fatigue performance of the alloy. To this purpose various heat treatments in a range of temperatures between 265°C and 300°C for a duration between 15 minutes and 2 hours are performed. The microstructure modifications are analysed using a scanning electron microscope and the residual stress state is measured by laboratory X-ray diffraction.
Additive manufacturing (AM) is becoming increasingly important in engineering applications due to the possibility of producing components with a high geometrical complexity allowing for optimized forms with respect to the in-service functionality. Despite the promising potential, AM components are still far from being used in safety-relevant applications, mainly due to a lack of understanding of the feedstock-process-properties-performance relationship. This work aims at providing a full characterization of the fatigue behavior of the additively manufactured AISI 316L austenitic stainless steel and a direct comparison with the fatigue performance of the wrought steel. To this purpose, a set of specimens has been produced by laser powder bed fusion (L-PBF) and subsequently heat treated at 900 °C for 1 hour for complete stress relief, whereas a second set of specimens has been machined out of hot-rolled plates. Low cycle fatigue (LCF) and high cycle fatigue (HCF) tests have been conducted for characterizing the fatigue behavior. The L-PBF material had a higher fatigue limit and better finite life performance compared to wrought material. Both, LCF and HCF-testing revealed an extensive cyclic softening.