Kerntechnische Entsorgung
Filtern
Erscheinungsjahr
- 2021 (50) (entfernen)
Dokumenttyp
- Vortrag (26)
- Beitrag zu einem Tagungsband (12)
- Posterpräsentation (6)
- Zeitschriftenartikel (5)
- Dissertation (1)
Schlagworte
- Monitoring (6)
- Compression set (4)
- Compression stress relaxation (4)
- Endlager (4)
- Ageing (3)
- Borehole probe (3)
- Distributed sensing (3)
- Engineered barrier (3)
- Faseroptischer Strahlungssensor (3)
- Interim storage (3)
Organisationseinheit der BAM
- 3 Gefahrgutumschließungen; Energiespeicher (25)
- 8 Zerstörungsfreie Prüfung (22)
- 8.2 Zerstörungsfreie Prüfmethoden für das Bauwesen (15)
- 3.3 Sicherheit von Transportbehältern (13)
- 3.4 Sicherheit von Lagerbehältern (12)
- 8.6 Faseroptische Sensorik (7)
- 7 Bauwerkssicherheit (3)
- 7.4 Baustofftechnologie (3)
- 9 Komponentensicherheit (2)
- 9.2 Versuchsanlagen und Prüftechnik (2)
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (26)
Packages for the transport of Spent Nuclear Fuel and high active radioactive waste are designed to withstand severe accidents. Specific mechanical and thermal tests are defined in the IAEA Regulations for the Safe Transport of Radioactive Materials in order to cover these hypothetical severe accidents. The thermal test mainly consists of a 30 minute fully engulfing fire. Components such as the package impact limiters can lead to supplementary energy release during the thermal test as they might continue burning after the fire phase. Local heat flux into the package can occur. Measurement of heat flux into the package is of importance to evaluate component temperatures and review their acceptance. The usability of heat flux sensors and temperature measurement equipment has to be tested to apply them in impact limiter fire testing. Further questions arise such as :“Is the infrared camera a useful tool to determine heat flux at the boundary surface?”
Investigation of the internal impact during a 9 m drop test of an accident-safe waste package
(2021)
The safety assessment of packages for the transport of radioactive material follows the IAEA regulations and guidance. The specified regulatory tests cover severe accidents and demonstrate the package containment system integrity.
Special attention must be drawn to the behaviour of the content which could move inside the package due to unpreventable gaps caused by the loading procedure and the structure of the content. A possible internal impact of the content which occurs during the drop tests onto the lid system is investigated. The IAEA regulations SSR-6 and the Guidance SSG-26, revised recently, consider input from Germany and France related to the significance of internal gaps.
In the context of a waste package design assessment, a model was equipped with a representative content to conduct a drop test with an internal impact. The weight and kinetic impact of this content covered all possible real contents. The objective of the test was to maximize the load onto the lid system and to prove the mechanical integrity by complying with the required leak tightness. The test was conducted
conservatively at a package temperature lower than -40 °C at the BAM Test Site Technical Safety.
This paper gives an overview of efforts to address internal gaps and their consequences, and the BAM efforts with the implementation of this topic into IAEA regulations and guidance material. The paper then focuses on the conduction of a drop test and investigation of internal component impact.
Investigation of the internal impact during a 9 m drop test of an accident-safe waste package
(2021)
The safety assessment of packages for the transport of radioactive material follows the IAEA regulations and guidance. The specified regulatory tests cover severe accidents and demonstrate the package containment system integrity. Special attention must be drawn to the behaviour of the content which could move inside the package due to unpreventable gaps caused by the loading procedure and the structure of the content. A possible internal impact of the content which occurs during the drop tests onto the lid system is investigated. The IAEA regulations SSR-6 and the Guidance SSG-26, revised recently, consider input from Germany and France related to the significance of internal gaps.
In the context of a waste package design assessment, a model was equipped with a representative content to conduct a drop test with an internal impact. The weight and kinetic impact of this content covered all possible real contents. The objective of the test was to maximize the load onto the lid system and to prove the mechanical integrity by complying with the required leak tightness. The test was conducted conservatively at a package temperature lower than -40 °C at the BAM Test Site Technical Safety.
This paper gives an overview of efforts to address internal gaps and their consequences, and the BAM efforts with the implementation of this topic into IAEA regulations and guidance material. The paper then focuses on the conduction of a drop test and investigation of internal component impact.
A novel ultrasonic borehole probe is developed for the quality assurance of sealing structures in radioactive waste repositories using existing research boreholes. The aim is to analyse the sealing structures made of salt concrete concerning potential cracks, delamination, and embedded objects. A first prototype of the probe uses 12 individual dry point contact (DPC) shear horizontal wave transducers separated by equidistant transmitter/receiver arrays, each consisting of six individual transducers. It is operated with a commercial handheld ultrasonic testing device used in civil engineering. In order to increase the generated sound pressure of the borehole probe, the number of transducers will be increased to 32 for the novel probe. In addition, a time-controlled excitation of the individual probes is used to steer a focused sound beam to a certain angle and focus on a certain distance based on calculated time delays. Hence, the sensitive test volume is more limited, and the signal-to-noise ratio of the received signals improved. This paper presents the validation of the newly developed phased array borehole probe by beam simulation and experimentally on a half-cylindrical test specimen to investigate the directional characteristics. In combination with geophysical reconstruction method, an optimised radiation characteristic of the probe, an improved signal quality and thus an increased reliability of the results in imaging is expected. This is of great importance to construct safe sealing structures needed for radioactive or toxic waste disposal.
The excellent mechanical properties of elastomer seals at a wide range of temperatures as well as their high versatility and recovery potential under several load conditions make these materials well suitable for the application in containers designed for transport and disposal of negligible heat generating radioactive waste. While a seal exchange at defined intervals is typical in many conventional applications, it is impossible or at least hard to perform when principles of minimization of radiation exposure have to be considered which prohibit an avoidable cask handling. An extensive knowledge of the change of the elastomer properties during aging and the availability of reliable end-of-lifetime criteria to guarantee the safe enclosure of the radioactive material for the required time are mandatory. As BAM is involved in most of the national cask licensing procedures and in the evaluation of cask-related long-term safety issues, great efforts have already been made and are still ongoing to scientifically support this task.
Among other representative types of elastomers, specimen made from ethylene propylene diene rubber (EPDM) were tested before, during and after aging to capture the with respect to application most important of their complex mechanical properties.
Exemplary results of these investigations were used to calibrate material models implemented in the commercial finite element software ABAQUS/Standard®. The finite element model already presented in previous works uses a sequential temperature displacement coupling. The calculated compression stress relaxation (CSR) and compression set (CS) values do satisfactorily match the experimental results.
In many investigations performed at BAM both values (CSR and CS) were identified as key indicators of elastomer’s long-term performance.
However, the possibility to correlate these equivalent indicators with performance values such as tightness and leakage rate, measurable in the mounted state, is an important goal of our future work. In the presented study the ABAQUS® feature of “pressure penetration” is introduced in the suggested finite element model for this purpose. It provides the possibility to simulate the penetration of a gas into a possible gap between flange and O-ring causing an opening of a leakage path. Three dimensional and axis-symmetric finite element models were generated to represent flat and grooved flanges of different dimensions.
The sensitivity of the feature to several input parameters is investigated and the observed behavior of the O-ring is correlated with the results of performed leakage tests.
The excellent mechanical properties of elastomer seals at a wide range of temperatures as well as their high versatility and recovery potential under several load conditions make these materials well suitable for the application in containers designed for transport and disposal of negligible heat generating radioactive waste. While a seal exchange at defined intervals is typical in many conventional applications, it is impossible or at least hard to perform when principles of minimization of radiation exposure have to be considered which prohibit an avoidable cask handling. An extensive knowledge of the change of the elastomer properties during aging and the availability of reliable end-of-lifetime criteria to guarantee the safe enclosure of the radioactive material for the required time are mandatory. As BAM is involved in most of the national cask licensing procedures and in the evaluation of cask-related long-term safety issues, great efforts have already been made and are still ongoing to scientifically support this task.
Among other representative types of elastomers, specimen made from ethylene propylene diene rubber (EPDM) were tested before, during and after aging to capture the with respect to application most important of their complex mechanical properties.
Exemplary results of these investigations were used to calibrate material models implemented in the commercial finite element software ABAQUS/Standard®. The finite element model already presented in previous works uses a sequential temperature displacement coupling. The calculated compression stress relaxation (CSR) and compression set (CS) values do satisfactorily match the experimental results.
In many investigations performed at BAM both values (CSR and CS) were identified as key indicators of elastomer’s long-term performance.
However, the possibility to correlate these equivalent indicators with performance values such as tightness and leakage rate, measurable in the mounted state, is an important goal of our future work. In the presented study the ABAQUS® feature of “pressure penetration” is introduced in the suggested finite element model for this purpose. It provides the possibility to simulate the penetration of a gas into a possible gap between flange and O-ring causing an opening of a leakage path. Three dimensional and axis-symmetric finite element models were generated to represent flat and grooved flanges of different dimensions.
The sensitivity of the feature to several input parameters is investigated and the observed behavior of the O-ring is correlated with the results of performed leakage tests.
Stoßdämpfer, die zum Schutz von Behältern zum Transport radioaktiver Stoffe eingesetzt werden und welche häufig aus von Stahlblech ummantelten, geschichtetem Holz bestehen, reduzieren bei einem etwaigen Unfall die auf den Behälterkörper wirkende mechanische Belastung erheblich. In Zulassungsverfahren muss die Sicherheit der jeweiligen Behälterkonstruktion nachgewiesen werden, wobei u. a. der Nachweis erbracht werden muss, dass die Behälter definierten Prüfbedingungen widerstehen. Diese beinhalten Aufprallsequenzen aus verschiedenen Höhen und Positionen sowie ein anschließendes das Versandstück 30 min lang allumhüllendes Feuer bei 800°C. Falls Stoßdämpfer infolge der 30-minütigen Feuerbeanspruchung in Brand geraten, dürfen diese unter den Prüfbedingungen nicht gelöscht werden. Die Auswirkungen auf die Sicherheit des Behälters sind hierbei zu untersuchen. Das ist die Basis für die in dieser Arbeit durchgeführten Untersuchungen zum Brandverhalten von stahlblechumkapselten Holzstrukturen mit dem Ziel der Bewertung der daraus resultierenden zusätzlichen thermischen Belastung auf den Behälter. Ein wesentlicher Bestandteil war die Durchführung eines Großbrandversuchs, bei dem ein originalgroßer Stoßdämpfer auf dem Brandprüfstand während einer 30-minütigen Feuerphase entzündet wurde. Der Stoßdämpfer hatte ein Volumen von 3m³ und war mit aus den Prüfbedingungen resultierenden Vorschädigungen versehen. Es wurde ein Prüfstand zur Messung der variablen Wärmeleistung des brennenden Stoßdämpfers entwickelt. Die Wärme wird dabei in den Energieaufnahmebehälter (EAB) eingetragen. Aufgrund der entwickelten Temperaturregelung konnte die Wärmeleistung mit geringen Messfehlern bestimmt werden. Dabei wurde der EAB um maximal 10 K erwärmt. Im Großbrandversuch wurde gezeigt, dass der vorgeschädigte Stoßdämpfer 72 h lang brannte und dass eine signifikante Wärmeleistung in den EAB eingetragen wurde. Die während des Stoßdämpferbrands erzeugte Energie betrug ein Vielfaches im Vergleich zur Wärmeleistung, die allein durch das IAEA-Feuer eingetragen wird. Temperaturen von bis zu 1100°C wurden erreicht. Im Versuch wurde Flammenschlagen im Stoßdämpferinnern und das Glühen der Stoßdämpferstahlblechummantelung beobachtet. Bewusst dessen, dass ein einzig durchgeführter Brandversuch nur unzulängliche Aussagekraft hat, um das Brandverhalten von Stoßdämpfern zu beschreiben, wurde in weiteren Kleinbrandversuchen die Parameterabhängigkeit beim Brand von stahlblechumkapselten Holzstrukturen untersucht. Dafür wurde das Brandverhalten von 8 zylinderförmigen 0,07m³ großen Probekörpern bei variabler Schadstellengröße getestet. In der Bewertung der Kleinbrandversuche konnte gezeigt werden, dass eine kritische Schadstellengröße existiert und welche Streubreite in den Kleinbrandversuchen vorliegt. Die Kleinbrandversuche können damit Aufschluss darüber geben, welche Abweichungen in weiteren Großbrandversuchen zu erwarten wären.
Aging of elastomer O-rings and PE neutron shielding materials for radioactive waste containers
(2021)
Our institution BAM in Berlin, Germany is concerned with research and testing of materials in the context of safety in chemistry and technology. Our working group is involved in the licensing procedures of casks for radioactive waste. Besides, we’re doing research on aging and lifetime prediction of elastomer O-rings and investigate degradation and thermal expansion of PE neutron shielding materials.
Zu jedem Endlager gehört die Entwicklung eines Verschlusskonzept. Im Endlager Morsleben und an anderer Stelle werden in Abhängigkeit vom Wirtsgestein verschiedene Materialien und Bauweisen für Streckenverschlüsse entwickelt und in großem Maßstab erprobt. Hierzu gehören auch Maßnahmen der Qualitätssicherung, die Informationen über Ausführung und Zustand der Versuchsbauwerke liefern. Hierzu werden von der Bundesanstalt für Materialforschung und -prüfung (BAM) für verschiedene Forschungsvorhaben und Prüfaufträge Methoden und Geräte getestet, verbessert und vor Ort unter Tage eingesetzt Die hier beschriebenen Verfahren lassen sich auch zu Untersuchungen im Wirtsgestein anwenden.
Zu jedem Endlager gehört die Entwicklung eines Verschlusskonzept. Im Endlager Morsleben und an anderer Stelle werden in Abhängigkeit vom Wirtsgestein verschiedene Materialien und Bauweisen für Streckenverschlüsse entwickelt und in großem Maßstab erprobt. Hierzu gehören auch Maßnahmen der Qualitätssicherung, die Informationen über Ausführung und Zustand der Versuchsbauwerke liefern. Hierzu werden von der Bundesanstalt für Materialforschung und -prüfung (BAM) für verschiedene Forschungsvorhaben und Prüfaufträge Methoden und Geräte getestet, verbessert und vor Ort unter Tage eingesetzt. Die hier beschriebenen Verfahren lassen sich auch zu Untersuchungen im Wirtsgestein anwenden.