Präsentation
Filtern
Erscheinungsjahr
- 2017 (8) (entfernen)
Dokumenttyp
- Posterpräsentation (6)
- Vortrag (2)
Sprache
- Englisch (8)
Referierte Publikation
- nein (8)
Schlagworte
- ToF-SIMS (8) (entfernen)
Eingeladener Vortrag
- nein (2)
The synthesis of TiO2 nanoplatelets with fluorine-containing reactants is carried out using titanium (IV) butoxide as precursor and concentrated HF as shape controller, the final product requires a working up in order to eliminate or at least to reduce the amount of residual fluorides, which is realized here by well-defined thermal treatment of the samples. Bulk and surface sensitive methods namely scanning electron microscopy with energydispersive X-ray spectroscopy (SEM-EDX), Auger electron spectroscopy (AES) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) have been applied to trace the presence of any fluorides in dependence on different information depths and measurement sensitivities of these methods.
The ferroelectric ceramic NBT and its solid solutions with barium titanate (BT) are examples for the most promising lead free materials to substitute the dominant Pb(Zr,Ti)O3 (PZT). Lead based material should generally be disregarded due to environmental and health reasons. However, there is no class of lead-free piezoelectric materials that can replace PZT entirely. Not only the often inferior ferroelectric properties but also the lack of understanding of the defect chemistry of NBT is still a challenge for the replacement of lead containing piezo-ceramics. Just recently it could be shown by Li et al. that NBT obtains extraordinarily high oxygen ionic conductivity when doped with Mg as acceptor. It was actually expected that doping just leads to a hardening of the ferroelectric properties. However, it became clear that the known defect chemical behavior of PZT cannot be extrapolated to NBT materials. Hence, to gain information on general doping effects a better defect chemical investigation is needed. This is particularly important for the applications with high reliability demands to investigate possible degradation and fatigue mechanisms.
In the present work Time-of-flight-secondary ion mass spectrometry (ToF-SIMS) was used in order to observe the influence of different acceptor dopants (Fe, Ni, Al) on the oxygen diffusion in NBT. ToF-SIMS holds the ability to gain a full elemental distribution in a sub-micron resolution and was therefore chosen to provide the essential information on the favorable diffusion paths of oxygen in NBT in dependence of the chosen doping element. 18O was used as a tracer for oxygen as its natural abundance is only 0.2%. The doped NBT samples have been annealed for 5 h at 500°C in a 0.2 bar 18O-tracer atmosphere to be able to detect oxygen ion diffusion. ToF-SIMS investigations were conducted on a ToF-SIMS IV (ION TOF GmbH, Münster, Germany) using a Bi+ primary ion beam (25KeV in collimated burst alignment mode with a beam diameter of ~150 nm) and a Cs+ sputter beam (3KeV).
The results illustrate the different impact of dopants on the diffusion properties which is evidence for a highly non-linear dependence on dopant type and concentration.
In the course of the energy transformation from fossil fuels to renewable energy sources, the use of hydrogen as fuel and energy storage can play a key role. This presents new challenges to industry and scientific community alike.
The storage and transport of hydrogen, which is nowadays mainly realised by austenitic stainless steels, remains problematic. That is due to the degradation of mechanical properties and the possibility of phase transformation by hydrogen diffusion and accumulation. Development of materials and technologies requires a fundamental understanding of these degradation processes. Therefore, studying the behaviour of hydrogen in austenitic steel contributes to an understanding of the damage processes which is crucial for both life assessment and safe use of components in industry and transportation.
As one of the few tools that is capable of depicting the distribution of hydrogen in steels, time-of-flight secondary ion mass spectrometry (ToF-SIMS) was conducted after electrochemical charging. To obtain furthermore information about the structural composition and cracking behaviour, electron-backscattered diffraction (EBSD) and scanning electron microscopy (SEM) were performed. Gathered data of chemical composition and topography was treated employing data fusion, thus creating a comprehensive portrait of hydrogen-induced effects in the austenite grade AISI 304L.
Specimens were electrochemically charged with deuterium instead of hydrogen. This arises from the difficulties to distinguish between artificially charged hydrogen and traces existing in the material or the rest gas in the analysis chamber. Similar diffusion and permeation behaviour, as well as solubility, allow nonetheless to draw conclusions from the experiments.
Self-assembly of TiO2 nanoparticles in multiple layers by layer-by-layer deposition has been selected of different deposition procedures usually applied for fabrication of TiO2 thin films with defined and homogeneous thickness on supports of interest for the large-scale applications. The substrates tested were: conductive (FTO) glass, silica glass and titanium alloy. The selected film fabrication technique consists of the deposition of alternating layers of oppositely charged, i.e. functionalized, TiO2 nanoparticle layers with wash steps in between. The controlled assembly of TiO2 nanoparticles on the supports surface requires both a proper functionalization of the supports to promote the adhesion of the TiO2 film to the substrates and proper functionalization of TiO2 nanoparticles to allow attachment to substrate and subsequent reaction between different NP layers. The current study focusses on the analytical control of the functionalization of the substrates with 3-Aminopropyltriethoxysilane (APTS) and glutaraldehyde (GA) by means of surface sensitive methods, XPS, Auger Electron Spectroscopy (AES) and ToF-SIMS. Chemical composition of surface of functionalized substrates shows differences in the degree and type of modification in dependence on substrate.
The ferroelectric ceramic NBT and its solid solutions with barium titanate (BT) are examples for the most promising lead free materials to substitute the dominant Pb(Zr,Ti)O3 (PZT). Lead based material should generally be disregarded due to environmental and health reasons. However, there is no class of lead-free piezoelectric materials that can replace PZT entirely. Not only the often inferior ferroelectric properties but also the lack of understanding of the defect chemistry of NBT is still a challenge for the replacement of lead containing piezo-ceramics. Just recently it could be shown by Li et al.[1] that NBT obtains extraordinarily high oxygen ionic conductivity when doped with Mg as acceptor. It was actually expected that doping just leads to a hardening of the ferroelectric properties. However, it became clear that the known defect chemical behavior of PZT cannot be extrapolated to NBT materials. Hence, to gain information on general doping effects a better defect chemical investigation is needed. This is particularly important for the applications with high reliability demands to investigate possible degradation and fatigue mechanisms.
In the present work Time-of-flight-secondary ion mass spectrometry (ToF-SIMS) was used in order to observe the influence of different acceptor dopants (Fe, Ni, Al) on the oxygen diffusion in NBT. ToF-SIMS holds the ability to gain a full elemental distribution in a sub-micron resolution and was therefore chosen to provide the essential information on the favorable diffusion paths of oxygen in NBT in dependence of the chosen doping element. 18O was used as a tracer for oxygen as its natural abundance is only 0.2%. The doped NBT samples have been annealed for 5 h at 500°C in a 0.2 bar 18O-tracer atmosphere to be able to detect oxygen ion diffusion. ToF-SIMS investigations were conducted on a ToF-SIMS IV (ION TOF GmbH, Münster, Germany) using a Bi+ primary ion beam (25KeV in collimated burst alignment mode with a beam diameter of ~150 nm) and a Cs+ sputter beam (3KeV).
The results illustrate the different impact of dopants on the diffusion properties which is evidence for a highly non-linear dependence on dopant type and concentration.
1) Li, M., et al., Nature Materials, 2014. 13(1): p. 31-35.
The use of duplex stainless steels (DSS) in energy related applications is well known. Nowadays, DSSs become more favorable than austenitic steels due to the outstanding mechanical properties, the good corrosion resistance and the lower nickel content.However, the use of the duplex grade in acidic environments such as seawater can lead to a severe degradation in the structural integrity of the steel by hydrogen-induced/assisted cracking mechanisms, which can eventually result in premature failure. Hydrogen assisted degradation and cracking of steels remains unclear even though this topic is intensively studied for more than a century. The main gap lies in the validation of the proposed theoretical models at the sub-micron scale. Industrial and the research communities define a need for an accurate method by which it is possible to image the distribution of hydrogen in the microstructure. Among the very few available methods nowadays, Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) provides precise mapping of hydrogen in the microstructure. Moreover, the powerful combination of ToF-SIMS with multivariate data analysis (MVA), electron backscattered diffraction (EBSD) for providing a the structural information and the use of data fusion techniques can contribute to a better understanding of the hydrogen induced degradation processes in the material.
In the present work two types of duplex grades were chosen as a case study (standard and lean DSS). The duplex class, consist of equivalent amounts of ferrite and austenite, was investigated by ToF-SIMS and EBSD during and after electrochemical deuterium charging in order to simulate the service of a component in acidic environments. Deuterium is known to act on the steel similarly to hydrogen and therefore was used as a tracer for hydrogen. The results show that the ferrite was affected almost identical in both steels whereas in the austenitic phase significant differences were observed in the lean duplex in comparison to the standard duplex. The advantage of the combined techniques is reflected by the ability to correlate the hydrogen distribution in the microstructure to the resulted structural changes.
Hydrothermal synthesis of anatase TiO2 nanosheets with a high fraction of exposed {001} facets and related high photocatalytic activity - as an alternative to bipyramidal anatase TiO2 nanoparticles mainly exposing the {101} facets. The scope of the material preparation work is the thermal reduction of residual fluorides from HF (capping agent) induced during the synthesis of TiO2 nanosheets by calcination at 873K. The analytical task consists of detection and localization of fluorine present at the surface and/or in the bulk of TiO2 nanosheets before and after calcination by SEM/EDX, Auger electron spectroscopy and ToF-SIMS.
Organic surface modification and analysis of TiO2 nanoparticles for self-assembly in multiple layers
(2017)
Parameters of TiO2 coatings can greatly influence their final performance in largescale applications such as photocatalytic measurements, orthopedic and/or dental prostheses, cell cultures, and dye-sensitized solar cells. From different film deposition procedures, self-assembly of TiO2 NPs in multiple layers was selected for systematic characterization. EDX, AES and ToF-SIMS analysis have been carried out in order to evaluate the functionalization of several types of TiO2 NPs differing in size, shape and surface area.