Präsentation
Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (19981)
- Posterpräsentation (6200)
- Beitrag zu einem Tagungsband (36)
- Sonstiges (8)
- Zeitschriftenartikel (2)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (2)
Sprache
- Deutsch (16750)
- Englisch (9425)
- Mehrsprachig (25)
- Spanisch (13)
- Französisch (11)
- Russisch (3)
- Tschechisch (1)
- Ungarisch (1)
Schlagworte
- Korrosion (265)
- Corrosion (182)
- Additive manufacturing (159)
- Nanoparticles (151)
- Additive Manufacturing (147)
- LIBS (137)
- Hydrogen (125)
- Concrete (123)
- Fluorescence (123)
- Additive Fertigung (121)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (1249)
- 6 Materialchemie (1190)
- 1 Analytische Chemie; Referenzmaterialien (949)
- 7 Bauwerkssicherheit (913)
- 9 Komponentensicherheit (815)
- 4 Material und Umwelt (584)
- 5 Werkstofftechnik (576)
- 3 Gefahrgutumschließungen; Energiespeicher (526)
- 9.4 Integrität von Schweißverbindungen (377)
- 7.6 Korrosion und Korrosionsschutz (373)
The slip-rolling 2Disk tribometer from Optimol Instruments represented the technological evolution in tribotesting of the well-known AMSLER-type tribometer marketed in 1922. Both use two discs with the same outer diameter rolling against each other on their circumference. In the AMSLER, the lower disc dips into an oil reservoir, whereas in the 2Disk the oil is injected into the contact. The oil supply of the 2Disk is controlled by pump and temperature by a heat exchanger.
Thermographic super resolution techniques allow the spatial resolution of defects/inhomogeneities below the classical limit, which is governed by the diffusion properties of thermal wave propagation. In this work, we re-port on the extension of this approach towards a full frame 2D super resolution technique. The approach is based on a repeated spatially structured heating using high power lasers. In a second post-processing step, several measurements are coherently combined using mathematical optimization and taking advantage of the (joint) sparsity of the defects in the sample.
Graphene derivatives have shown great promise in the field of pathogen binding and sensing. Due to their diverse applications, they show a variety of activities that range from bacterial adhesion to bacterial resistance. Therefore, domination of the graphene-pathogen interactions is highly relevant for producing 2D platforms with the desired applications. In order to gain control over the interactions between graphene and biosystems, mechanisms should be fully understood. The surface functionality of graphene is one of the most important factors that dominates its interactions with biosystems and pathogens. Covalent functionalization is a robust method through which functionality, chemical structure, and subsequently physicochemical properties of graphene are abundantly manipulated. A critical issue for preparing graphene-based 2D materials with a defined surface structure, however, is controlling the functionalization in terms of number, position, and type of functional groups.
Graphene and its derivatives have recently attracted much attention for sensing and deactivating pathogens. However, mechanism of multivalent interactions at the graphene-pathogen interface are not fully understood. Since different physicochemical parameters of graphene play a role at this interface, control over graphene’s structure is necessary to study the mechanism of these interactions. In this work, zwitterionic graphene nanomaterials (ZGNMs) were synthesized with defined isoelectric points and exposure, in terms of polymer coverage and functionality. Then, the switchable interactions of ZGNMs with E. coli were investigated to study the validity of the generally proposed “trapping” mechanism for inactivating pathogens by functionalized graphene derivatives. The ZGNMs were able to controllably trap and release E. coli by crossing their isoelectric points.
In civil engineering the information about the quantitative ingress of harmful species like Cl⁻, Na⁺ and SO²⁻₄ is of great interest to evaluate the remaining life time of structures. These species are triggering different damage processes like the alkali-silica reaction (ASR) or the chloride-induced corrosion of the reinforcement. For the evaluation of the heterogeneous concrete it is necessary to discriminate between the different phases mainly cement matrix and aggregates. The transport processes are only proceeding in the cement matrix therefore the measured concentrations should be regarded to the cement content. For the 2D evaluation of element distributions different multivariate cluster-algorithms like k-means and Expectation-Maximization-algorithm (EM-algorithm) have been tested. The methods are compared and different figures of merit will be presented. After phase separation non-relevant information of the aggregates can be excluded. The ingress of harmful species is then quantified using chemometrics. Due to concrete cores from a parking deck the methods have been validated and verified with standard methods of wet-chemistry.
The combination of microstructural data with other experimental techniques and with modeling is paramount, if we want to extract the maximum amount of information on porous material properties. In particular, quantitative image analysis, statistical approaches, direct discretization of tomographic reconstructions represent concrete possibilities to extend the power of the tomographic 3D representation to insights into the material and component performance. I will show a few examples of possible use of X-ray tomographic data for quantitative assessment of porosity in ceramics.
Moreover, I will show how not-so-novel 2D characterization techniques, based X-ray refraction, can allow a great deal of insights in the damage evolution in microcracked (and porous) ceramics. I will show how X-ray refraction can detect objects (e.g. microcracks) below its own spatial resolution.
Finally, I will discuss the link between the microstructural findings and the mechanical properties of porous microcracked ceramics.
The combination of microstructural data with other experimental techniques and with modeling is paramount, if we want to extract the maximum amount of information on porous material properties. In particular, quantitative image analysis, statistical approaches, direct discretization of tomographic reconstructions represent concrete possibilities to extend the power of the tomographic 3D representation to insights into the material and component performance. I will show a few examples of possible use of X-ray tomographic data for quantitative assessment of porosity in ceramics.
Moreover, I will show how not-so-novel 2D characterization techniques, based X-ray refraction, can allow a great deal of insights in the damage evolution in microcracked (and porous) ceramics. I will show how X-ray refraction can detect objects (e.g. microcracks) below its own spatial resolution.
Finally, I will discuss the link between the microstructural findings and the mechanical properties of porous microcracked ceramics.
One-part-geopolymers, produced by addition of water to a mixture of solid silica and sodium alumi-nate, are a less exhaustively studied approach to form geopolymeric binders. Depending on the silica source, the reaction products show significant amounts of zeolite Na-A besides amorphous compounds. Previously, 29Si MAS NMR has been used to analyze the chemical structure of such one-part geopolymers, having crystalline structures and amorphous phases (Q2, Q3, Q4).
In this work, pure zeolites and three different one-part-geopolymers cured for 1 day were investigated by 29Si-27Al TRAPDOR NMR. It was used to identify aluminum phases in overlapping silicon sites. Zeolites Na-X (Si/Al=1.4) and Na-Y (Si/Al=2.7) served as model systems to measure the TRAPDOR effect of the structural units Q4(mAl). Both materials show several Q4(mAl) signals, which are all separated by their chemical shifts. The more aluminum surrounds the silicon tetrahedron the higher are the normalized TRAPDOR difference signals (S0/∆S). The intensity ratios between Q4(mAl) to Q4({m-1}Al) of these signals is fixed but vary slightly between both zeolites. These results are transferred to the complex geopolymer structure.