Datei im Netzwerk der BAM verfügbar ("Closed Access")
Filtern
Erscheinungsjahr
- 2015 (73) (entfernen)
Dokumenttyp
- Vortrag (73) (entfernen)
Referierte Publikation
- nein (73)
Schlagworte
- Quantitative NMR-Spektroskopie (4)
- qNMR (4)
- Impact (3)
- Reaction monitoring (3)
- Stress wave propagation (3)
- Degradation (2)
- Electron backscatter diffraction (2)
- Fatigue (2)
- Mesoscale (2)
- Metrologie (2)
Eingeladener Vortrag
- nein (73)
Aktueller Stand der Normung
(2015)
Increasing performance and energy efficiency of Gas Metal Arc Welding by a high power tandem process
(2015)
Standard Gas Metal Arc Welding (Standard GMAW) and a high power Tandem GMAW (TGMAW) process are evaluated with respect to energy efficiency. Current, voltage and overall equipment power are measured and energy consumption is determined. The new key performance indicator Electrical Deposition Efficiency is introduced to reflect the energy efficiency of GMAW processes. Additionally, wallplug efficiency of the equipment is determined in order to identify the overall energy consumption. Results show that energy efficiency as well as economic process performance can be significantly increased by application of the TGMAW process. Furthermore findings indicate that wall-plug efficiency of the equipment is independent of power Level and material transfer mode. A metal plate of 30 mm thick structural steel is joined by Standard GMAW and TGMAW to demonstrate the total energy savings for a real weld. Electricity consumption is reduced by more than 20 % using the high power TGMAW process.
Ultra-high performance concrete (UHPC) is characterized by outstanding compressive strength of more than 150 MPa, double of normal concrete. Furthermore UHPC has a very dense structure which leads to an extremely low permeability for fluids resulting in with a very high durability.
Further structural improvement can be achieved with thermal treatment of UHPC. Recent studies have shown that an increase in compressive strength of more than 50% is possible. Nevertheless, the accurate conditions for an optimal thermal treatment are still not determined. A multitude of parameters can be varied: Temperature, pressure, water saturation, duration of the process steps.
Primary object of this study is the optimization of the conditions for thermal treatment focused to the treatment duration at a defined temperature and pressure (185°C / 1,1MPa). Therefore, the thermally treated UHPC samples are analysed by mean of mechanical properties and phase composition.
The development of phases and strength at higher temperature differs fundamentally from other cementitious systems (like normal concrete or autoclaved aerated concrete), although the chemical composition is similar. Because of the very dense structure and the low water/cement ratio the availability of water is low. This influences the hydration process. As a consequence tobermorite is absent in thermal treated UHPC in contrast to thermally treated normal concrete or predictions based on thermodynamic modelling.
We present fundamentals for the selection of fluorescent dyes and show the challenges of the implementation of fluorescent dyes in silicone rubber materials for the production of fluorescent all-silicone rubber POF.
The following paper focuses on the evolution of micro damage in short fibre reinforced polyamide. Therefore, tube samples are subjected to uni- and biaxial fatigue loadings. The evolution of micro damage is analysed by the non-destructive method of X-ray refraction analysis with consideration of the fibre orientation distribution. For validation of the applied micro damage models, fractographic analyses are performed. Concluding some general results, it has been observed that the load ratio influences the quantitative dominance of micro damage, whereas occurring damage phenomena depend on the type of loading (i.e. tension and torsion). Thus, zones in the Haigh-diagram are detected, where the occurrence of damage mechanisms qualitatively and quantitatively changes. This is a basis for further research regarding anisotropic damage criteria.
Ober die europäischen Produktnormen für Geokunststoffe (hEN) wird gestritten: Dienen sie nur einem einheitlichen Verfahren der CE-Kennzeichnung oder werden darin alle relevanten geotechnischen Eigenschaften so verbindlich festgelegt, dass darüber hinausgehende nationale Vorschriften ungültig werden? Der Streit wurde durch ein Urteil des Europäischen Gerichtshofs weiter angefacht. Davon noch nicht betroffen ist der Deponiebau. Die Deponie ist ein besonderes Bauwerk, bei dem vor allem abfallrechtliche Regelungen beachtet werden müssen. In der deutschen Deponieverordnung wurde daher eine mit der Europäischen Kommission abgestimmte Gleichwertigkeitsklausel für CE-gekennzeichnete Bauprodukte verankert, die diese Besonderheit berücksichtigt. Wir zeigen, dass das in den hEN festgelegte Eigenschaftsspektrum der Bauprodukte im Wesentlichen nicht gleichwertig zu dem Spektrum ist, das sich aus den Anforderungen der Deponieverordnung ergibt. Die Qualitätssicherung der hEN, die nur eine zertifizierte werkseigene Produktionskontrolle jedoch keine Fremdüberwachung vorsieht, entspricht ebenfalls nicht den Anforderungen der Deponieverordnung. Eine CE-Kennzeichnung kann daher eine BAM-Zulassung nicht gleichwertig ersetzen. Auch für andere geotechnische Anwendungsgebiete gilt, dass die geltenden hEN die Geokunststoffe nicht ausreichend charakterisieren. Die Antwort auf die Frage, wie verbindlich diese mangelhaften hEN werden könnten, ist daher von weitreichender Bedeutung für die gesamte Geotechnik.