Datei im Netzwerk der BAM verfügbar ("Closed Access")
Filtern
Dokumenttyp
- Zeitschriftenartikel (22)
Sprache
- Englisch (22)
Referierte Publikation
- ja (22)
Schlagworte
- Hybrid mixtures (5)
- Dust explosions (4)
- Gas explosions (4)
- Inerting effect (3)
- Minimum ignition temperature (3)
- CO2/N2 ratio (2)
- Combustion duration time (2)
- Explosion criterion (2)
- Hybrid mixture (2)
- Hydrogen (2)
Organisationseinheit der BAM
Paper des Monats
- ja (1)
The combustion characteristics and explosive hazard of syngas (H2/CO)/air mixtures are affected by its exact composition and equivalence ratios. In this paper, the explosion pressure and spectral radiant intensity of free radicals were quantitatively examined for syngas with different H2 proportions ([H2 in syngas] = 0, 30, 50, 70, 100 vol%) and equivalence ratios (φ = 0.8, 1.0, 1.2, 1.4, 1.6, 2.0, 2.5). The results show that the explosion process of syngas/air mixtures can be separated into the initial slow combustion stage, the violent deflagration stage and the deflagration ending stage. The peaks of explosion pressure, pressure rise rate, OH*spectral intensity and rise rate of spectral intensity first increase and then decrease with increasing the equivalence ratio, and they reduce gradually with the decrease of H2 proportion in syngas. The H2 content in syngas greatly affects the heat release and the concentration of excited state OH*, especially for the syngas/air mixtures with smaller proportion of H2. Additionally, the presence of H2 greatly increases the deflagration index and spectral radiant index of OH* for syngas/air mixtures. The average rise rates of explosion pressure and spectral intensity of free radicals are introduced and the coupling model between them is established based on the first law of thermodynamics and the principle of chain reaction. The established model is furthermore verified by the experimental results. It is indicated that there is a linear relationship between average rise rates of explosion pressure and spectral intensity (OH*). The results can be used to improve the combustion efficiency of syngas and to guide theoretically the prevention, mitigation and control of syngas explosions.
The hybrid mixture of combustible dusts and flammable gases/vapours widely exist in various industries, including mining, petrochemical, metallurgical, textile and pharmaceutical. It may pose a higher explosion risk than gas/vapor or dust/mist explosions since the hybrid explosions can still be initiated even though both the gas and the dust concentration are lower than their lower explosion limit (LEL) values. Understanding the explosion threat of hybrid mixtures not only contributes to the inherent safety and sustainability of industrial process design, but promotes the efficiency of loss prevention and mitigation. To date, however, there is no test standard with reliable explosion criteria available to determine the safety parameters of all types of hybrid mixture explosions, nor the flame propagation and quenching mechanism or theoretical explanation behind these parameters. This review presents a state-of-the-art overview of the comprehensive understanding of hybrid mixture explosions mainly in an experimental study level; thereby, the main limitations and challenges to be faced are explored. The discussed main contents include the experimental measurement for the safety parameters of hybrid mixtures (i.e., explosion sensitivity and severity parameters) via typical test apparatuses, explosion regime and criterion of hybrid mixtures, the detailed flame propagation/quenching characteristics behind the explosion severities/sensitivities of hybrid mixtures. This work aims to summarize the essential basics of experimental studies, and to provide the perspectives based on the current research gaps to understand the explosion hazards of hybrid mixtures in-depth.
Minimum explosion concentration (MEC) of three agriculture dusts and two coal dusts was studied via a 20-L explosion chamber to reveal the role of gaseous inhibitors. Both active method (CO2 diluting air) and passive method (CO2 replacing O2) were used. The TG and DTG thermal analysis tests were conducted to study the pyrolysis and combustion characteristics of dust samples. An alternative explosion criterion based on combustion duration time was used to determine MEC, and compared with the standardized overpressure method. Under 10-kJ ignition condition, as oxygen mole fraction (XO2) decreased from 21% to 10%, MEC of agriculture dusts and coal dusts respectively increased by around 5 times and 2 times. The active inerting method with a lower N2/CO2 ratio was found to have a better suppression effect on the explosion of the five carbonaceous dusts because the blend has a higher specific heat and a lower oxygen diffusion rate.
The explosion characteristics of anthracite and bituminous coals in O2/N2 ambience were experimentally studied via a 20-L spherical explosion chamber with various ignition energies of 2, 5 and 10 kJ. A novel method based on combustion duration time was proposed for the first time, with an emphasis on the determination of the limiting oxygen concentration (LOC). The values of LOC determined by the alternative method were almost consistent with those obtained by using the standardized overpressure method, where the LOCs were above 21.6%, 19.8%, and 13.2% for anthracite coal and 11.4%, 9.6%, and 9.0% for bituminous coal when the ignition energy is 2, 5, and 10 kJ, respectively. But the newly proposed method was found to be much less affected by the ignition energy compared with the standardized overpressure method, taking combustion duration time as an explosion criterion thus had a higher efficiency and required fewer experiments. The results also showed that as oxygen concentration decreases from 21.6% to 14.4%, the maximum explosion pressure decreases from 0.4334 MPa to 0.1034 MPa for anthracite coal and from 0.5664 MPa to 0.3981 MPa for bituminous coal, respectively. Moreover, the effect of ignition energy varied with varying volatile matter content and ignition mechanism of coal dusts. The higher the volatile content, the less sensitive it is to the ignition energy. The newly proposed method will provide a reference for the new standard development, hazard analysis, explosion prevention and suppression by involving the use of inert gases of combustible powder industries.
Iron dust explosion characteristics with small amount of nano-sized Fe2O3 and Fe3O4 particles
(2022)
Iron powder, as one of the most abundant metal fuels that can be used as recyclable carriers of clean energy, is a promising alternative to fossil fuels in a future low-carbon economy. It may pose a potential explosion hazard during the process of processing, storage, transport, and reduction/oxidation (redox). The explosion characteristics of iron dust in air were undertaken via a 20 L spherical explosion chamber with an emphasis on minimum explosion concentration (MEC) of iron dust. The alternative method of combustion duration time (tc) was used to determine MEC and compared with the standardized over pressure method. Two kinds of nano-sized iron oxides (Fe2O3 and Fe3O4) were used as inertants to determine the inhibition effect of different oxidation products. The iron dust explosion products with various shapes and sizes were found to be able to grow up 4–6 times of the iron dust for the first time. Adding small amount of Fe2O3 or Fe3O4 could reduce the explosion severity and sensitivity of iron dust. The MEC data determined by both methods were comparable. The addition of 5 % oxide has obvious inhibition effect under 1500 g/m3 concentration. With the increase of oxide concentration to 10 %, the inerting effect increases, and the MEC of iron dust increases more than 3 times. The increase of dust concentration will weaken the inerting effect. When the concentration increases from 500 g/m3 to 3000 g/m3, the weakening effect of 10 % Fe2O3 on the explosion pressure decreases from 38.45 % to 2.24 %, and 10 % Fe3O4 decreases from 46.21 % to 10.63 %. Unlike coal, biomass or aluminum dusts, the iron dust explosion was found to have a unique secondary acceleration of pressure rise rate for the first time. These results provide a fundamental basis to mitigate the iron dust explosion via solid inerting method without adding extra elements.
MIKE III apparatus tests were conducted to investigate the minimum ignition energy (MIE) of coal dusts in air and O2/CO2 atmospheres with and without small amount of CH4/H2. The O2 mole fraction (XO2) in the gas mixtures varied from 21% to 50% with the CH4/H2 mole fraction from 0 to 2%. Experimental result showed that MIE of coal dusts significantly decreases even by three orders of magnitude in mJ with increasing XO2 and the addition of CH4/H2. Compared with CH4, H2 had a relatively strong promotion effect on the spark ignition of coal dusts. The inhibiting effect of CO2 was found to be much stronger than N2, but this inhibiting effect of CO2 could be eliminated by 9% increment of XO2. The effect on MIE of coal dusts thus followed by the order: 9% increment of XO2 > CO2 replacing N2 > 2% CH4 or H2 addition. Moreover, two empirical models were used to estimate the MIE of hybrid dust-gas mixture (HMIE), and the results showed that calculated data can well reflect the promoting effect of elevated XO2 and flammable gas addition, and the inhibiting effect of inert gas
The poor thermal conductivity of MH beds limits hydrogen absorption in metal hydride (MH) reactors for thermochemical heat storage. The compaction of MH powder with expanded natural graphite (ENG) is an efficient and cost-effective approach for the heat transfer enhancement of MH beds. However, the addition of ENG reduces the hydrogen storage density of the compacted composites. How to optimize the allocation of a limited amount of ENG in the MH bed has not been studied. In this study, a multilayer MH bed configuration with an ENG grade content was adopted to improve the heat transfer performance of an MH reactor for thermochemical heat storage. The effect of the ENG content gradient on the performance of the MH reactor was investigated using a mathematical model of the MH reactor. Furthermore, an optimization method based on the entransy dissipation extremum principle (EDEP) was proposed to optimize the ENG distribution in magnesium hydride (MgH2)-ENG compacts. The results showed that a larger ENG content gradient resulted in faster hydrogen absorption and better heat-discharge performance. Compared with a configuration with a uniform ENG content, the optimized configuration based on the EDEP exhibited a shorter reaction time, more uniform bed temperature distribution, and 15.33% higher gravimetric exergy-output rate. In addition, the number of optimization iterations had little effect on the optimal results, which could be obtained by implementing only one optimization iteration. The optimization results showed that more ENG should be allocated to the internal layer of the MgH2-ENG compact. The compacts were divided into three layers, and the ENG content of each layer was calculated according to the optimized configuration based on the EDEP. The optimization method proposed in this study can be applied to optimize
minimum explosion concentration (MEC) and limiting oxygen concentration (LOC) in our recent works. This work further studies the reasonability and reliability of the alternative method experimentally and theoretically. Six different dust samples were tested via a 20-L spherical explosion chamber. The experimental results showed that the data of MEC and LOC determined by using the alternative and the standardized methods are in good agreement. The minimum flame propagation velocity (Sf) and the corresponding maximum combustion duration time (tc) were found at its MEC and LOC, suggesting that the theoretical analysis can well explain all the experimental data. It is the first time to study the theoretical basis of the explosion criterion, thus helping to improve our understandings of dust explosion characteristics, and to amend the explosion criterion in future test standards.
Self-sustaining smoldering as a novel disposal approach for food waste with high moisture content
(2021)
This work aims to explore the self-sustaining smoldering treatment (SSST) for the destruction of food waste. The food waste used in this work mainly consists of cereal, vegetable, and meat. To examine the processing procedures and parameters, three experimental groups (raw food waste, food-waste paste and food-waste paste blended with anthracite) and five variables (moisture content, sand size, sand-to-food waste ratio, air flow and food waste-to-coal ratio) were extensively investigated. Results show that raw food waste with 40% moisture content can be disposed by SSST with the mass destruction ratio over 90%. However, the robustness of SSST for raw food waste is constrained by the heterogeneous issue due to a variety of components and sizes of food waste. This issue is addressed through stir pre-processing of raw food waste as food-waste paste. The robustness of SSST for food waste is significantly further enhanced only if a slight mass fraction of anthracite (<20% of raw food waste) is supplemented. This provides an alternative solution for employing SSST for raw food waste with very high moisture content.
Hydrogen leakage of vehicles in the tunnel is a great threat to the safety operation of the tunnel and longitudinal ventilation strategies have always been utilized to control the fire and smoke movement of rail transit, electric and fossil-fueled vehicles in the engineering field. It is in doubt whether the longitudinal ventilation strategy could still help to reduce the jet fire hazard of transportation with H2 power in the tunnel, considering the rapid development of the hydrogen energy. In present work, a numerical research on effects of longitudinal ventilation strategies on hydrogen jet flames in the tunnel is conducted. The results illustrate that longitudinal ventilation could affect the flame characteristics of jet flames greatly in the tunnel. The critical ventilation velocity increases firstly with the increase of hydrogen leakage rates and then changes little after a critical value. The predicted theoretical model of pool fires could well predict the critical ventilation velocity for hydrogen jet fires. With the increase of longitudinal ventilation velocity, maximum ceiling temperatures are decreased greatly. According to the heat releases, jet speeds and ventilation velocities, three kinds of flame bending characteristics of hydrogen jet fire could be observed due to different effects of the inertial force. At last, the stable thermal stratification could also be destroyed by large ventilation velocities but the corresponding ventilation velocity is far larger than the critical ventilation one. With the increase of longitudinal ventilation velocities, the height of thermal layer is reduced firstly and then maintained at a constant value.
A series of experiments were conducted in a 10L closed and vented tube with L/D = 10.0, and effects of initial fuel volume concentration, inert gas dilutions (diluted by N2 and CO2), inert gas–water mist twin fluid medium dilutions (diluted by N2-H2O twin fluid medium, CO2-H2O twin fluid medium) and end boundary conditions on overpressure transients of hydrocarbon fuel–air mixtures explosion were revealed. Results show that the overpressure-time profiles consistent with the dynamic evolution law of ‘approximately zero-1st overpressure rising stage-2nd overpressure rising stage-descending stage’, and ‘rate of overpressure rise-time’ curves exhibit the characteristics of multi-stages and multi-peaks, such as (dp/dt)(1,max), (dp/dt)(1,min), (dp/dt)(2,max) and (dp/dt)(2,min). Specifically, as the fuel volume concentration increased, both the maximum overpressures (pmax), and the maximum rates of overpressure rise ((dp/dt)(1,max) and (dp/dt)(2,max)) show a variation trend of increasing firstly and then decreasing, while the corresponding times (tmax, θ(1,max) , θ(2,max)) show a total different variation trend. Moreover, when YCH is lower than 1.88%, the value of (dp/dt)(1,max) is greater than (dp/dt)(2,max), while the value of (dp/dt)(1,max) was less than (dp/dt)(2,max), and when YCH was higher than 1.88%. The addition of N2 and CO2 can obviously inhibit the explosion intensity of hydrocarbon fuel, and the inhibition effect of CO2 is better than that of N2. Due to the synergy inhibition effect of the inert gas and ultrafine water mist, all the values of pmax, (dp/dt)(1,max) and (dp/dt)(2,max) diluted by inert gas-ultrafine water mist twin fluid medium were smaller than those diluted by sole inert gases. In addition, there are significant differences in the overpressure-time and the rate of overpressure rise-time profiles between closed and end venting explosions. The values of maximum overpressure and the rates of overpressure rise of the closed explosion were higher than those of the venting explosion, but the minimum rate of overpressure rise is a smaller one.
Safety concerns on cable tray fires in urban utility tunnels, which may further trigger huge casualties, ceiling structure damages, power failures and other domino effects, attract increasing attention in recent years. Determining the maximum excess ceiling gas temperature (MECT) induced by cable tray fires in urban utility tunnels is crucial to evaluate the fire risks. A series of one-layer horizontal cable tray fire experiments to explore the MECT were carried out in a large-scale utility tunnel without mechanical ventilations. The number of cables on the tray was varied from 8 to 18 in the experiments. The experimental results showed that the cable tray fire burning could be divided into three distinct stages, including ignition, self-sustaining and decaying stages. In the self-sustaining combustion stage, the cable tray was found to burn relatively steady. The mean MECT was also investigated since it represents one of the main characteristics of the cable tray fire. By redefining two parameters (the heat release rate and the effective ceiling height) in three classical MECT models proposed originally based on pool-fire, these three models could be extended to be able to predict the mean MECT generated from the cable tray fire (solid combustible) within 20% deviations. Consequently, two novel models were respectively proposed to predict the mean MECT at the self-sustaining burning period and the instantaneous MECT of one-layer horizontal cable tray fire in utility tunnel, which would be useful in the field of fire protection engineering.
Minimum ignition temperature of dust clouds (MITC) was studied experimentally and theoretically in different atmospheres. Three carbonaceous dusts were tested in both air and O2/CO2 atmospheres with CH4 mole fraction from 0 to 2%. Results showed that the ignition risk of the three dusts significantly increases (decrease of MITC by ~100 ℃) with increasing XO2 from 21% to 50%, but significantly decreases replacing N2 in air with CO2. The inhibition effect of CO2 on MITCs could be diminished by increasing XO2 or adding CH4. The addition of small amount of CH4 has different effects on the MITCs of different dust samples, following the opposite order of volatile matter content: anthracite>bituminous coal>starch. Two modified steady-state ignition models, considering the density of mixture gas and dust cloud, XO2 and its diffusivity, were developed to interpret the experimental observations. The analysis revealed that the global heterogeneous ignition model suits well for the hybrid mixtures of anthracite or bituminous coal dusts. In contrast, the proposed global homogeneous ignition model was found to be only valid for the pure starch dust, and the extra CH4 addition could strongly affect the ignition process of starch, particularly in O2/CO2 atmospheres with higher XO2.
The explosion characteristics of anthracite coal dust with/without small amount of CH4 (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (Pex) and the rate of explosion pressure rise ((dp/dt)ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N2 with CO2, suggesting that CO2 has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH4 moderates the inhibition effect of CO2 and the promotion effect of O2 on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH4 mixture explosions, Barknecht’s curve was found to be more accurate and conservative than Chatelier’s line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.
The data center needs more and more electricity due to the explosive growth of IT servers and it could cause electricity power shortage and huge carbon emission. It is an attractive and promising solution to power the data center with hydrogen energy source. The present work aims to conduct an economic analysis on the hydrogen-powered data center. Configurations of hydrogen-powered and traditional data centers are compared and the differences focus on backup power system, converter/inverter, fuel cell subsystem, carbon emission, hydrogen and electricity consumptions. Economic analysis is conducted to evaluate the feasibility to power the data center with hydrogen energy source. Results show that electricity price increasing rate and hydrogen cost are the main factors to influence economic feasibility of hydrogen-powered data center. When the electricity price keeps constant in the coming two decades, the critical hydrogen price is about 2.8 U.S. dollar per kilogram. If the electricity price could increase 5% annually due to explosive growth of electric vehicles and economy, critical hydrogen price will become 6.4 U.S. dollar per kilogram. Hydrogen sources and transportation determine the hydrogen price together. Hydrogen production cost varies greatly with hydrogen sources and production technologies. Hydrogen transport cost is greatly influenced by distances and H2 consumptions to consumers. It could be summarized that the hydrogen-powered data center is economic if hydrogen could be produced from natural gas or H2-rich industrial waste streams in chemical plant and data center could not be built too far away from hydrogen sources. In addition, large-scale hydrogen-powered data center is more likely to be economic. Solar hydrogen powered data center has entered into a critical stage in the economic feasibility. Solar hydrogen production cost has restrained the H2 utilization in data center power systems now, since it could be competitive only when more strict carbon emission regulation is employed, hydrogen production cost reduces greatly and electricity price is increasing greatly in the future. However, it could be expected solar hydrogen-powered system will be adopted as the power source of data centers in the next few years.
The semi-batch reactors (SBRs) system, which is widely used in industrial processes, possesses an intrinsic parametric sensitivity, in which infinitesimal disturbances of input parameters can result in large variations in output variables. In this work, local parametric sensitivity analysis (PSA) was used to understand parameter variations and global PSA was conducted to examine the interaction of input parameters. The effects of these parameters on the output of the system model were analyzed based on the Monte Carlo method with Latin hypercube sampling and the extended Fourier amplitude sensitivity test model. The results showed that the evolution of thermal behaviors in SBRs were observed: marginal ignition; thermal runaway; and the quick onset, fair conversion, and smooth temperature profile. The threshold point of transition from marginal ignition to thermal runaway was at the maximal value of local sensitivity, for which the slope with respect to cooling temperature equaled zero. Moreover, the sequence of the global sensitivity of six common input parameters was computed and evaluated. The reliability of the numerical models was verified by using our previous experimental results of cyclohexanone peroxide reaction. This comprehensive sensitivity analysis could provide valuable operating information to improve chemical process safety.
To reveal and improve our understanding of the ignition behavior and mechanism, G-G furnace experiments of three typical organic dusts were performed to investigate the minimum ignition temperature (MIT) in O2/N2, O2/ Ar and O2/CO2 atmospheres with oxygen mole fraction from 8.4% to 50%. The experimental results were presented in oxygen-lean and oxy-fuel atmospheres to evaluate the ignition sensitivity of dusts in different atmospheres. It was found that CO2 is the strongest in terms of lowing the ignition sensitivity of the three dusts, and the dust explosion risk increases significantly with increasing O2 mole fraction for the three dusts through a logarithmically and significantly reducing MIT. However, for different dusts, inert gases show different suppression effects. In addition, a modified steady-state homogeneous ignition model was proposed and successfully applied to oxygen-lean atmospheres, and in oxy-fuel atmospheres, this model has also been improved to estimate the ignition mechanism. This ignition mechanism model could be used to successfully predict the minimum ignition temperature of high volatile dust under different inert atmospheres controlled by homogeneous ignition, which will provide a reference for the ignition hazard assessment of dust on hot surfaces.
Thermoelectric generator (TEG) has been proved as a promising technology for directly converting heat into electricity based on Seebeck effect. On the contrary, this electricity can trigger a solid-state cooling based on conventional Peltier effect. However, these two effects induce a coupling between heat and electric flux, especially for the quantitative relationship still remaining a mystery. Here, we show experimental evidence and theoretical calculation for the coupling by monitoring transient response of fluid temperature and output power. The experimental maximum heat flow in open circuit is 1162 W at cold fluid flow rate = 0.3 m3/h and fluid temperature difference ΔTf = 70 °C, enhanced by 13% owing to heat compensation from intrinsic coupling in closed-loop circuit. Meanwhile, the measured maximum output power of TEG is 18.2 W, and subsequently decreases to 15.4 W due to the objective existence of coupling. This double-edged sword in coupling vigorously inspires the potential applications in heat-dissipation situation such as spacecraft, electronic components, photovoltaic, refrigerator and etc. Present findings open a novel avenue for manipulating heat-electricity conversion in practical engineering.
Gaseous inhibitors are used in many industries for the explosion prevention of combustible dusts, mitigating the potential hazard to humans, properties and environments. This work experimentally and theoretically studied the inerting effect of gaseous inhibitors on the ignition process of dust clouds in O2/N2/CO2 atmospheres, with an emphasis on the role of the CO2/N2 ratio. 10 different combustible carbonaceous dusts were selected, including grain dust, biomass dust and coal dust. Experimental results showed that the inhibition effect of CO2/N2 is closely related to the ignition mechanism of dust clouds. Specifically, a higher ratio of CO2/N2 yields a stronger inhibition effect on the ignition process of dust samples with relatively low volatile matter contents predominated by heterogeneous ignition. In addition, two novel steady-state ignition mechanism models were developed to interpret the experimental observations. Maxwell-Stefan equations were used to describe the diffusivity in the ternary O2/N2/CO2 gas mixtures. The analytical results were in good agreement with the experimental data of the minimum ignition temperature of dust cloud (MITC) in oxygen-lean atmospheres. The mechanism modelling can be used to estimate the critical ignition temperature of all carbonaceous dust clouds with a wide range of volatile matter content under different inert atmospheres, which will provide a reference for the explosion hazard assessment of dust posed by a hot surface in the process industries.
Experiments were conducted in a semi-confined pipe to investigate the effects of obstacle location and gasoline vapor concentration on gasoline-air fuel explosions. The variations of internal overpressure, external overpressure, flame propagation and flame-overpressure coupling relationship were analyzed. The results showed thatthe internal overpressure histories existed three obvious peaks, and when the obstacle location was set at 0.4 m, the maximum absolute values of overpressure (pmax and pneg), overpressure rise rates ((dp/dt)ave and (dp/dt)max) and the deflagration index (KG) were obtained. Additionally, more than two positive overpressure peaks were observed in the external overpressure histories. The maximum values of external overpressures and overpressure rise rates were obtained at the obstacle location of 0.4 m. For the fuel concentrations of 1.3%,.1.7% and 2.1%, the shortest time to reach pmax appeared at the obstacle location of 0.4 m, 0.2 m and 0.6 m, respectively, while the shortest time to reach (dp/dt)max and the maximum flame propagation speed were obtained for all the fuel concentrations at the obstacle location of 0.2 m. Moreover, a coupling relationship between overpressure and flame propagation was found. lt could be tleduced that the formation of the positive overpressure peak ofthe external overpressure might be directly related to the gas explosion inside the pipe and the flow jet caused by the high-speed flame propagation. rat her than the external explosion (or secondary explosion) out of the pipe. These results improve our understanding on gas explosion dynamics in a semi- confined space.