Eigenverlag BAM
Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (4355) (entfernen)
Sprache
- Deutsch (4286)
- Englisch (66)
- Mehrsprachig (2)
- Polnisch (1)
Schlagworte
- Beton (7)
- POD (6)
- Computed tomography (5)
- Zerstörungsfreie Prüfung (5)
- Computertomographie (4)
- Deponieverordnung (4)
- Geokunststoffe (4)
- Human factors (4)
- Ultraschallprüfung (4)
- Zulassungsrichtlinien (4)
Organisationseinheit der BAM
The present work demonstrates a sustainable approach of using relatively coarser iron ore particles for ironmaking. The motivation is to reduce the energy consumption in the milling of the iron ore by utilizing coarser iron ore particles (+0.05 mm) and to select a suitable binder for improving pellet properties. Iron ore fines in the range of 0.05–0.25 mm was selected and classified into three size ranges. Fluxed iron ore pellets were prepared using lime as a binder for the basicity of 0, 1, and 2. Reduction of these pellets with a packed bed of coal fines was performed in the temperature range of 900–1200 °C for a duration of 30–120 min. The direct reduction kinetics of the iron ore pellets were studied by employing diffusion and chemical reaction control models to the experimental data. The results show that pellets made with coarser iron ore particles have improved reduction behavior and kinetics. The reduction reaction is found to be a mixed control. The activation energy for the reduction reaction varies from 44.3 to 74.76 kJ mol−1 as iron ore particle size decreases from 0.25 to 0.05 mm and basicity increases from 0 to 2.
The industrial sintering process used to produce metallic matrix pads has been altered to diminish the amount of copper used. Unfortunately, replacing a large part of the copper with iron seems to have reached a limit. In the high-energy, emergency-type rail braking used in this study, the materials are put to the very limit of their usage capacity, allowing us to observe the evolution of the microstructure and mechanical properties of sintered, metallic matrix pads. After the braking test, their compressive behaviour was assessed using digital image correlation (DIC), and their microstructure with scanning electron microscopy (SEM). The worn material has three flat layers with different microstructures and compressive behaviours. The boom layer seems unmodified. Macroscopic and microscopic cracks run through the intermediate layer (2–15 mm depth). The top layer has stiffened thanks to resolidification of copper. The temperature reaches 1000 °C during the braking test, which also explains the carbon diffusion into iron that result in the weakening of iron–graphite interfaces in the pad. Finally, submicronic particles are detected at many open interfaces of the worn and compressed pad. Associated with the predominant role of graphite particles, this explains the weak compressive behaviour of the pads.
The huge atomic heterogeneity of high-entropy materials along with a possibility to unravel the behavior of individual components at the atomic scale suggests a great promise in designing new compositionally complex systems with the desired multi-functionality. Herein, we apply multi-edge X-ray absorption spectroscopy (extended X-ray absorption fine structure (EXAFS), X-ray absorption near edge structure (XANES), and X-ray magnetic circular dichroism (XMCD)) to probe the structural, electronic, and magnetic properties of all individual constituents in the single-phase face-centered cubic (fcc)-structured nanocrystalline thin film of Cr20Mn26Fe18Co19Ni17 (at.%) high-entropy alloy on the local scale. The local crystallographic ordering and component-dependent lattice displacements were explored within the reverse Monte Carlo approach applied to EXAFS spectra collected at the K absorption edges of several constituents at room temperature. A homogeneous short-range fcc atomic environment around the absorbers of each type with very similar statistically averaged interatomic distances (2.54–2.55 Å) to their nearest-neighbors and enlarged structural relaxations of Cr atoms were revealed. XANES and XMCD spectra collected at the L2,3 absorption edges of all principal components at low temperature from the oxidized and in situ cleaned surfaces were used to probe the oxidation states, the changes in the electronic structure, and magnetic behavior of all constituents at the surface and in the sub-surface volume of the film. The spin and orbital magnetic moments of Fe, Co, and Ni components were quantitatively evaluated. The presence of magnetic phase transitions and the co-existence of different magnetic phases were uncovered by conventional magnetometry in a broad temperature range.
The superior properties of high-entropy multi-functional materials are strongly connected with their atomic heterogeneity through many different local atomic interactions. The detailed element-specific studies on a local scale can provide insight into the primary arrangements of atoms in multicomponent systems and benefit to unravel the role of individual components in certain macroscopic properties of complex compounds. Herein, multi-edge X-ray absorption spectroscopy combined with reverse Monte Carlo simulations was used to explore a homogeneity of the local crystallographic ordering and specific structure relaxations of each constituent in the equiatomic single-phase facecentered cubic CrMnFeCoNi high-entropy alloy at room temperature. Within the considered fitting approach, all five elements of the alloy were found to be distributed at the nodes of the fcc lattice without any signatures of the additional phases at the atomic scale and exhibit very close statistically averaged interatomic distances (2.54 – 2.55 Å) with their nearest-neighbors. Enlarged structural displacements were found solely for Cr atoms. The macroscopic magnetic properties probed by conventional magnetometry demonstrate no opening of the hysteresis loops at 5 K and illustrate a complex character of the long-range magnetic order after field-assisted cooling in ± 5 T. The observed magnetic behavior is assigned to effects related to structural relaxations of Cr. Besides, the advantages and limitations of the reverse Monte Carlo approach to studies of multicomponent systems like high-entropy alloys are highlighted.
Background: Host–pathogen interactions can lead to dramatic changes in host feeding behaviour. One aspect of this includes self-medication, where infected individuals consume substances such as toxins or alter their macronutrient consumption to enhance immune competence. Another widely adopted animal response to infection is illness-induced anorexia, which is thought to assist host immunity directly or by limiting the nutritional resources available to pathogens. Here, we recorded macronutrient preferences of the global pest cockroach, Blatta orientalis to investigate how shifts in host macronutrient dietary preference and quantity of carbohydrate (C) and protein (P) interact with immunity following bacterial infection.
Results: We fnd that B. orientalis avoids diets enriched for P under normal conditions, and that high P diets reduce cockroach survival in the long term. However, following bacterial challenge, cockroaches signifcantly reduced their overall nutrient intake, particularly of carbohydrates, and increased the relative ratio of protein (P:C) consumed. Surprisingly, these behavioural shifts had a limited efect on cockroach immunity and survival, with minor changes to immune protein abundance and antimicrobial activity between individuals placed on diferent diets, regardless of infection status.
Conclusions: We show that cockroach feeding behaviour can be modulated by a pathogen, resulting in an illness-induced anorexia-like feeding response and a shift from a C-enriched to a more P:C equal diet. However, our results also indicate that such responses do not provide signifcant immune protection in B. orientalis, suggesting that the host’s dietary shift might also result from random rather than directed behaviour. The lack of an apparent beneft of the shift in feeding behaviour highlights a possible reduced importance of diet in immune regulation in these invasive animals, although further investigations employing pathogens with alternative infection strategies are warranted.
The present study investigates the possibility of improving the selective oxidation of methane to formaldehyde over V-SBA-15 catalysts in two different ways. In a classical approach of catalyst optimization, the in situ synthesis of V-SBA-15 catalysts was optimized with regard to the applied pH value. Among the set of catalysts synthesized, a higher amount of incorporated vanadium, a higher content of polymeric VOx species as well as a less ordered structure of the support material were observed by increasing the pH values from 2.0 to 3.0. An optimum in performance during the selective oxidation of methane to formaldehyde with respect to activity and selectivity was found over V-SBA-15 prepared at a pH value of 2.5. With this knowledge, we have now evaluated the possibilities of reaction control using this catalyst. Specifically, artificial neural network modelling was applied after the collection of 232 training samples for obtaining insight into the influence of different reaction parameters (temperature; gas hourly space velocity (GHSV); and concentration of O2, N2 and H2O) onto methane conversion and selectivity towards formaldehyde.
This optimization of reaction conditions resulted in an outstanding high space-time yield of 13.6 kgCH2O∙kgcat∙h−1
Popioły pochodzące z instalacji do spalania komunalnych osadów ściekowych, znajdującej się na terytorium Polski, poddano procesom termochemicznego przekształcania, dzięki czemu otrzymano produkty nawozowe spełniające kryteria dopuszczające je do obrotu jako nawozy mineralne. Ponadto dokonano analizy możliwości wykorzystania popiołów na cele nawozowe zgodnie z obecnie przyjętymi dokumentami strategicznymi i planistycznymi dotyczącymi gospodarki odpadami na poziomie krajowym i europejskim.
An automatic sample changer chamber for total reflection X-ray fluorescence (TXRF) and X-ray absorption near-edge structure (XANES) analysis in TXRF geometry was successfully set up at the BAMline at BESSY II. TXRF and TXRF-XANES are valuable tools for elemental determination and speciation, especially where sample amounts are limited (<1 mg) and concentrations are low (ng ml⁻¹ to μg ml⁻¹). TXRF requires a well defined geometry regarding the reflecting surface of a sample carrier and the synchrotron beam. The newly installed chamber allows for reliable sample positioning, remote sample changing and evacuation of the fluorescence beam path. The chamber was successfully used showing accurate determination of elemental amounts in the certified reference material NISTwater 1640. Low limits of detection of less than 100 fg absolute (10 pg ml⁻¹) for Ni were found. TXRF-XANES on different Re species was applied. An unknown species of Re was found to be Re in the +7 oxidation state.
A new concept that comprises both time- and lateral-resolved X-ray absorption fine-structure information simultaneously in a single shot is presented. This uncomplicated set-up was tested at the BAMline at BESSY-II (Berlin, Germany). The primary broadband beam was generated by a double multilayer monochromator. The transmitted beam through the sample is diffracted by a convexly bent Si (111) crystal, producing a divergent beam. This, in turn, is collected by either an energy-sensitive area detector, the so-called color X-ray camera, or by an area-sensitive detector based on a CCD camera, in θ-2θ geometry. The first tests were performed with thin metal foils and some iron oxide mixtures. A time resolution of lower than 1 s together with a spatial resolution in one dimension of at least 50 µm is achieved.
The adsorption behavior of Platinum nanoparticles was studied for the as-received catalyst (under inert gas), under hydrogen and CO atmosphere using our newly designed in-situ cell. X-ray Absorption Spectroscopy (XAS) and Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) experiments were performed simultaneously with high data quality. Structural information and the type of adsorbate could be revealed via Extended X-ray Absorption Fine Structure (EXAFS) analysis, Δμ X-ray Absorption Near Edge Structure analysis (Δμ XANES) and in-situ DRIFTS. The as-received catalyst showed sub-surface oxygen and O(n-fold). Under CO atmosphere only CO(atop) was found. Reversible adsorbate induced changes of the Pt nanoparticle structure were derived from changes in the Pt-Pt coordination number and the corresponding bond distance. Under reducing conditions (H2, CO) a significant increase in both values occurred. Temperature dependent desorption of CO revealed a gradual shift from Pt-CO to Pt-O. Reoxidation was clearly assigned to strong metal support interaction from the SiO2 support.
Ein Impuls-Wirbelstromprüfsystem mit rechnergestützter Erfassung und Auswertung der Meßsignale
(1982)
Pulvermetallurgisch erzeugtes Referenzmaterial für die Spektral- und Röntgenfluoreszenzanalyse
(1983)
In this paper, the friction stir welding process was numerically investigated for 6 mm thick aluminum alloy AA2024-T3. The finite element software COMSOL Multiphysics was used to calculate the transient thermal field during welding and the mechanical reaction depending on different mechanical clamping conditions and hardening models subsequently. A thermal pseudo-mechanical (TPM) heat source was implemented.
Softening effects of the material due to precipitation hardening dissolution caused by the frictional heat were accounted for. The transient temperature evolution measured by thermocouple elements at various locations was compared to the numerical results. A good agreement was found for the thermal field. A sensitivity study of the mechanical models showed the strong influence of the clamping conditions and the softening model.
The potentials of incoherent X-ray scattering (Compton) computed tomography (CT) are investigated. The imaging of materials of very different atomic number or density at once is generally a perpetual challenge for X-ray tomography or radiography. In a basic laboratory set-up for simultaneous perpendicular Compton scattering and direct beam attenuation tomography are conducted by single channel photon counting line scans. This results in asymmetric distortions of the projection profiles of the scattering CT data set. In a first approach, corrections of Compton scattering data by taking advantage of rotational symmetry yield tomograms without major geometric artefacts. A cylindrical sample composed of PE, PA, PVC, glass and wood demonstrates similar Compton contrast for all the substances, while the conventional absorption tomogram only reveals the two high order materials. Comparison to neutron tomography
reveals astonishing similarities except for the glass component (without hydrogen). Therefore, Compton CT offers the potential to replace neutron tomography, which requires much more efforts.
Ever larger high pressure die castings (HPDC) with ever thinner walls raise the issue of casting defects. Properties of components are often strongly influenced by inner porosity. In the case of high pressure die castings, shrinkage and gas porosity occur. Two possibilities of characterizing porosity - by microscopy and acitve thermography - are dealt with in two articles. In the previous article, the microscopic investigations are presented. In this article, first the feasibility of thermographic detection will be discussed based on simulations and, thereafter, the experimental determination of porosity with active thermography will be described.
Für die Berechnung des Crashverhaltens von Fahrzeugstrukturen muss zusätzlich zur Dehnratenabhängigkeit des plastischen Verformungsverhaltens des Grundwerkstoffs auch das Verhalten von Fügestellen bei hoher Beanspruchungsgeschwindigkeit bestimmt werden. Ziel der VDEh-Arbeitsgruppe 'Hochgeschwindigkeitszugversuche an gefügten Stählen' war die Erstellung eines Stahl-Eisen-Prüfblattes (SEP) zur Ermittlung crashrelevanter Kennwerte für gefügte Stahl-Feinbleche unter vereinheitlichten Prüfbedingungen. Zur Erarbeitung der in dieser Richtlinie zu formulierenden Empfehlungen wurden Scherzugversuche bei hoher Geschwindigkeit an punktgeschweißten und lasergeschweißten Proben von elf Prüflaboratorien durchgeführt. Der Beitrag beschreibt die Ergebnisse dieses Ringversuchs und seine Auswirkungen auf das SEP.
Sprödbruch und Bruchmechanik
(1981)
Radiographie mit Elektronen
(1981)
The memory effect in polyolefinic products: A tool for confirming the steam sterilization process
(2015)
DSC-Messungen von dampfsterilisierten medizinischen Produkten aus Polyolefinen zeigen beim ersten Heizvorgang als auffällige Besonderheit eine zusätzliche Stufe, bekannt als Temperpeak. Das Ziel dieser Untersuchungen ist, dieses Phänomen nachzuvollziehen und zu verstehen, um es als Nachweis für die Dampfsterilisation nutzen zu können. Dafür wurden PP- und PE-Proben unter verschiedenen Bedingungen dampfsterilisiert und im Ofen thermisch behandelt. Anschließend wurden die Proben mittels DSC untersucht und die Einflüsse der thermischen Behandlung und der mechanischen Beanspruchung analysiert. Um den Einfluss unterschiedlicher Materialspezifikationen zu prüfen, wurden zusätzlich verschiedene Referenzmaterialien (PE und PP) untersucht und GPC-Messungen durchgeführt. Des Weiteren wurde die Beständigkeit des Signals gegenüber der Zeit und der Temperatureinflüssen betrachtet. Die Untersuchungen zeigen, dass sich ein stabiler Memory-Effekt erzeugen lässt.
In den letzten Jahren werden vermehrt trocken ankoppelbare Ultraschall-Punktkontaktprüfköpfe erfolgreich für Prüfaufgaben im Bauwesen angewendet. Oft werden mehrere Punktkontaktprüfköpfe in einem Gehäuse zu einer Strahlergruppe kombiniert, um die Schallbündelung zu verbessern oder um einzelne Prüfköpfe nacheinander als Sender und Empfänger zu betreiben und die Messsignale nach der Messung einer SAFT-Auswertung zuzuführen. Alternativ können die einzelnen Prüfköpfe einer solchen Gruppe laufzeitgesteuert angeregt und dadurch schon während der Messung das Prüfkopfschallfeld beeinflusst werden. Für diese Technik sind die Bezeichnungen laufzeitgesteuerte Ultraschall-Gruppenstrahler oder 'Phased Array' gebräuchlich. Mit den präsentierten Untersuchungen sollen die Anwendungsmöglichkeiten der Gruppenstrahlertechnik im Niederfrequenzbereich durch den Einsatz von Punktkontaktprüfköpfen verbessert werden. Dazu werden verschiedene Wellenarten eingesetzt und der Einfluss der Anordnung der Strahlerelemente im Array untersucht.
SURTEC Berlin '81
(1981)
Grundlagen für die Einstufung von Kohlestäuben in die Gefahrklasse 4.2 der Beförderungsvorschriften
(1981)
A flexible, sustainable, one-step thermal decomposition route for the synthesis of hierarchical, heteroatom doped carbon foams is presented. Task-specific semi-organic crystals combine functions for three different purposes: the carbon and heteroatom source, a foaming agent (CO2) and an in situ generable template (NaCl). Insights to the decomposition pathway were gained through FTIR/MS coupled TGA and an ultrafast out-of-furnace heating procedure and the products were analysed with (HR)SEM/TEM, EELS, FTIR, and N2 sorption. The resulting macroporous carbon foams are excellent supports for metallic nanoparticles due to their hierarchical structure, high surface area and tuneable heteroatom contents. This was demonstrated for catalytically active copper or the magnetic CoNi alloy for water purification.
Zur Lösung bodendynamischer Probleme bei nichtlinearem Werkstoffverhalten durch Transformation
(1981)
Original equipment manufacturers (OEMs) and end-users perceive 'Zero Wear' differently. The 'Zero Wear' approach will be put into a general relation for different applications and illuminated by individual paths, either based on monolithic materials, thin film coatings or alternative base oils, featuring triboactive materials and lubricious oxides for tribological engine components and dry running foil bearings or specific DLC, ta-C and novel Zirconium-based thin film coatings for concentrated contacts above FZG 14 and alternative engine oils (NoSAP & bio-no-tox). The associated tribometric test equipments for these examples will also be detailed.
Zwischenlagerung von abgebrannten Brennelementen in Transportbehältern - Anhörung in Gorleben
(1981)
The inspection of the sealing weld is an important phase for the evaluation of the acceptability of final disposal canister, but the weld is only a part of the 3D shielding of copper shell. The main tasks for reliable NDT evaluation requires an extensive evaluation of the parameters which contains typical inspection related items like repeatability, S/N ratio, POD, setting up the equipment for inspection, and all practices for inspections. The other parameters are material parameters, their variation must be taken into account in the evaluation of NDT reliability. Further parameters include human factors, i. e. human inspectors and their interaction with technical systems; their effects were studied on an example of the evaluation of eddy current data. Final parameters are related to evaluation of detected defects, which means sizing and base for acceptance and this can be done in different ways. Some examples are given and results are compared with different methods for instance between radiographic testing and ultrasonic testing by raw data analysis and PA-SAFT results. Also, preliminary curves for the evaluation of metallographic results of 55 defects will be shown by EB weld measurements. Some practical items concerning copper inspections will be also discussed related to acceptability.
Anhand von computertomografischen Messungen und Modellrechnungen werden DIRECTT-Rekonstruktionen im Vergleich mit gefilterten Rückprojektionen bewertet. Dazu wird die Rekonstruktionsqualität mittels einer zirkular erweiterten Modulations-Transfer-Funktion (MTF) und mit integralen Kenngrößen im Radon- und im Ortsraum verglichen. Zur Überprüfung der Rekonstruktionsgenauigkeit experimenteller Daten werden Mustermessungen einfacher Probengeometrien unter definierten physikalischen Bedingungen durchgeführt. Diese beinhalten die Monochromasie, die Unterdrückung von Kantenartefakten und die radiometrische Intensitätsbestimmung. Für die Qualität der Rekonstruktionen mittels DIRECTT erweisen sich sowohl unterschiedliche Rekonstruktionsfilter als auch der Verzicht auf jede Filterung als unerheblich, im Gegensatz zur gefilterten Rückprojektion.
Typische 'Missing Wedge'(MW)-Artefakte in Rekonstruktionen der Computertomografie können mit dem iterativen DIRECTT-Algorithmus (Direkte iterative Rekonstruktion computertomografischer Trajektorien) unterdrückt werden. Die durch fehlende Projektionswinkel bedingten MW-Restriktionen betreffen bisher nur Sonderapplikationen der Röntgen- und Neutronentomografie, müssen in der Nanometer auflösenden Elektronentomografie jedoch als Standard akzeptiert werden. Die MW-Artefakte werden besonders effektiv mit einer spezifischen DIRECTT-Prozedur partiell diskreter Zwischenlösungen beseitigt. Für die Beurteilung der Abbildungsqualität werden Rekonstruktionen von vollständigen und unvollständigen Mess- und Modell-Datensätzen erzeugt und mit Ergebnissen anderer Algorithmen (gefilterte Rückprojektion (FBP) und ART-Methoden) verglichen. Die Fourier-Transformierten der Rekonstruktionen demonstrieren die erfolgreiche Ergänzung der fehlenden Information im MW-Bereich. Die quantitative Bewertung der lokalen Rekonstruktionsqualität mit Methoden der räumlichen Statistik ergibt auch für unterschiedliche Signal-Rausch-Verhältnisse signifikante Vorteile gegenüber FBP und ART.
Algorithms to estimate ultrasonic testing method based on the integrated use of indicators of reliability and accuracy are presented, and built according to the nature of techniques, features of their application and evaluation purposes (comparison of techniques, introduction of new methods, test procedures, etc.). On the basis of the main revision of ISO 5725-1, 5725-2 the estimation of reproducibility and repeatability of measured characteristics determine the design of reflectors and real defects, and thus the reliability of non-destructive testing, including ultrasonic inspection of railways.
Die Sicherheit von Radsatzwellen beruht gegenwärtig auf zwei Säulen: der Schwingfestigkeitsauslegung und periodischen Inspektionen. Ausgehend von einem Schadensfall, der gebrochenen ICE 3-Welle von Köln, 2008, werden ausgewählte Aspekte dieser beiden Säulen diskutiert und Vorschläge zur weiteren Verbesserung gemacht. Diese betreffen u. a. Fragen einer Betriebszeitbegrenzung, Veränderungen der Schwingfestigkeit während des Betriebs infolge von Korrosion und Steinschlag, den Einfluss von Korrosion auf Schwingrissinitiierung und -fortschritt, den potenziellen Einfluss nichtmetallischer Einschlüsse auf die Schwingfestigkeit, die Möglichkeiten, sie im Rahmen der Qualitätssicherung zu detektieren, sowie Fragen der Bruchmechanik und der Zuverlässigkeit zerstörungsfreier Schwingriss-Prüfverfahren im Rahmen eines Konzepts regelmäßiger Inspektionen.
Faserverbundwerkstoffe (Komposite) zeigen außergewöhnliche Veränderungen ihrer Eigenschaften in Abhängigkeit von der Betriebsdauer. Daraus leitet sich auch die Notwendigkeit ab, eine Methode zu finden, die in der Lage ist, Festigkeiten und Restfestigkeiten von Komposit-Druckbehältern zu ermitteln. Dies kann mittels Lastwechselprüfung oder in anderen Fällen vorzugsweise mittels der langsamen Berstprüfung erfolgen. Für eine aussagekräftige Beschreibung der Festigkeit bedürfen die Ergebnisse beider Prüfverfahren einer statistischen Auswertung. Aber insbesondere die statistische Auswertung der berstbezogenen Festigkeitseigenschaften unterliegt neben der Frage der Stichprobengröße einer großen Unsicherheit mit enormen Folgen. Dies ist die Frage, welche Verteilungsfunktion der Streuung der Festigkeitseigenschaft konservativ zugrundegelegt werden darf. So ist zu untersuchen, ob die Gaußsche Normalverteilung (NV) die wahre Verteilung richtig beschreibt. Es könnten aber auch andere Funktionen, wie z. B. die Weibull-Verteilung notwendig sein, um eine Überschätzung der Überlebenswahrscheinlichkeit bzw. Zuverlässigkeit in dem interessanten Bereich von einem Ausfall pro 104 bis 108 Druckbehältern zu vermeiden.
The tradition of discussing the newest achievements in the consideration of NDE reliability was continued with the 5th European American Workshop on Reliability of NDE (5th EAW) in Berlin in 2013. The Focus of this workshop was to determine the 'delta' between the laboratorylike conditions, in which reliability assessments are usually carried out, and the everyday field conditions. Which obstacles need to be still overcome and how do we get closer with our estimations to the real field reliability? With the joint effort of international researchers and in-field practitioners the up-to-date research was presented and discussed, culminating in a half-a-day long 'Open Space Technology' discussion. This paper presents the main conclusions of the workshop.
Since the beginnings of the European American Workshops (EAW) in 1997, the aim was to gather the experts in NDE reliability and discuss burning topics with the aim of identifying crucial problems and suggesting ways to move forward. This was usually achieved during the so-called break-out sessions, in which predetermined topics were discussed. During the 5th EAW, held in Berlin in 2013, this approach was replaced by an Open Space Technology (OST) approach. The benefit of this approach is seen in the freedom of topic choices, i. e., the topics are not predetermined but rather arise at that moment in that space and by the participants choice. The following topics arose: new reliability methods (Bayesian, MAPOD,
), structural health monitoring, definition of requirements of NDE by customer versus provider, what value of POD is good enough?, human factors, manual versus automated inspection, and basic concepts of reliability of NDE. The participants were encouraged to walk from one session to another and openly express their opinions. These were in the end summarized by a chosen group of moderators and presented in this paper.
The focus of NDT reliability research in the past was in the field of two high risk industries: (atomic) power plants and aircrafts. The responsible organizations have been well aware of the risks and founded projects to understand and optimize critical steps during production, operation and maintenance. But the use of NDT is not limited to these two fields. The risks during operation of chemical plants, trains or windmills are different from the area above but evident. The coverage by legal regulations is relatively low. Instead of this owner responsibility, product liability and financial issues are the driving forces to do inspections and to use non-destructive testing. The different targets and financial issues influence the practice of NDT-inspections. A survey of this practice and its results are shown.