7.6 Korrosion und Korrosionsschutz
Filtern
Dokumenttyp
- Vortrag (348)
- Zeitschriftenartikel (76)
- Beitrag zu einem Tagungsband (53)
- Sonstiges (53)
- Posterpräsentation (15)
- Forschungsbericht (11)
- Tagungsband (Herausgeberschaft für den kompletten Band) (3)
- Beitrag zu einem Sammelband (2)
- Dissertation (2)
- Handbuch (2)
Sprache
- Deutsch (321)
- Englisch (241)
- Mehrsprachig (2)
- Französisch (1)
Schlagworte
- Korrosion (237)
- Corrosion (162)
- Nichtrostender Stahl (62)
- KorroPad (49)
- Potentialfeldmessung (44)
- Korrosionsschutz (31)
- Zink (31)
- Korrosionsprüfung (29)
- Deckschichtbildung (28)
- Geothermal (27)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (565)
- 7.6 Korrosion und Korrosionsschutz (565)
- 5 Werkstofftechnik (45)
- 5.1 Mikrostruktur Design und Degradation (43)
- 3 Gefahrgutumschließungen; Energiespeicher (15)
- 3.2 Gefahrguttanks und Unfallmechanik (15)
- 8 Zerstörungsfreie Prüfung (14)
- 7.4 Baustofftechnologie (11)
- 8.2 Zerstörungsfreie Prüfmethoden für das Bauwesen (8)
- 6 Materialchemie (5)
In the late 1980s, a new type of corrosion appeared in drinking water installations where galvanized steel pipes failed forming a deep groove with no corrosion at the other surfaces. The reason was discussed quite fiercely between failure analysts and material suppliers. In the end the discussion lead to the solution: inductive welded pipes of a certain sulphur content were prone to selective corrosion. The history of the arguments is discussed using old communications between Wilhelm Schwenk and Wolfgang Stichel, who later published the results in a paper unfortunately only I german.
Thus the knowledge got lost and new cases based on the same material problems are observed in application of so-called C-Steel piping systems. Failure cases are shown.
The screening of coatings shows that the modification by adding individual pigment was not sufficient to protect carbon steel even during a short-term exposure, indicated by the discoloration after only seven days of exposure.
Electrochemical tests indicated that the coating cathodically protects carbon steel or slows down the corrosion reaction.
A long-term exposure test confirmed that the PANI/SiO2 modified coating successfully protects the carbon steel in the Sibayak artificial geothermal water at 150 °C for 6 months.
Corrosive geothermal brines are a major challenge to geothermal power-plants. For cost reasons, plant designers favorize low alloyed steels, e.g., carbon steel, which are susceptible to uniform and localized corrosion when exposed to geothermal brines having acidic and saline properties. To solve such problem, coatings or inhibitors would be a protective solution as an alternative to the use of high alloyed materials.
This study investigated a coating system consisting of polyaniline/silicon dioxide basing on locally available resources. Protection against corrosion of carbon steel is shown by long-term exposure and electrochemical tests of coated carbon steels, performed in an artificial acidic and saline geothermal brine, comparable to real conditions at a site in Indonesia.
Therefore, an integrated coating system is presented for corrosion protection, combining the electro-chemical functionality of polyaniline and the physical advantages of silica.
The critical chloride content C(crit) is an indicator for the corrosion resistance of reinforcing steels in concrete. In this article, several experimental methods for determining the critical chloride content C(crit) of mild and an alloyed (12% Cr) steel in cementitious materials are compared. The methods used include accelerated polarization tests and tests using more natural (unpolarized) conditions in which chloride ingress occurs by diffusion and capillary uptake. The advantages and disadvantages of the methods are discussed, in particular, with the objective of reaching a compromise between applicability to practice and feasibility in laboratory testing.
This work presents machine learning-inspired data fusion approaches to improve the non-destructive testing of reinforced concrete. The principal effects that are used for data fusion are shown theoretically. Their effectiveness is tested in case studies carried out on largescale concrete specimens with built-in chloride-induced rebar corrosion. The dataset consists of half-cell potential mapping, Wenner resistivity, microwave moisture and ground penetrating radar measurements. Data fusion is based on the logistic Regression algorithm.
It learns an optimal linear decision boundary from multivariate labeled training data, to separate intact and defect areas. The training data are generated in an experiment that simulates the entire life cycle of chloride-exposed concrete building parts. The unique possibility to monitor the deterioration, and targeted corrosion initiation, allows data labeling.
The results exhibit an improved sensitivity of the data fusion with logistic regression compared to the best individual method half-cell potential.
Der Vortrag vermittelt dem betreuenden DIN Normenausschuss NMP 177 einen Gesamtüberblick über das abgeschlossene WIPANO-Vorhaben "Normenentwurf für ein Prüfverfahren zur Bestimmung von Deckschichtwiderständen an Zinküberzügen mittels gelartiger Elektrolyte (GELELEK). Innerhalb des Vorhabens wurden die elektrochemischen Methoden und die Verfahrensparameter systematisch untersucht, ein Messsystem für Feldanwendungen entwickelt, ein Ringversuch mit über 20 Teilnehmern durchgeführt und ein Normenvorschlag erarbeitet. Die Förderzeile der Initiative WIPANO wurden erreicht. Die Erarbeitung eines auf den Ergebnissen beruhenden Normenentwurfs wird auf der nächsten Sitzung des NMP 177 gestartet.
Nachdem im Verbundprojekt COORAL das Hauptaugenmerk auf überkritisches CO2 gelegt wurde, d. h. Transport über kurze Strecken bei erhöhter Temperatur, wurde in CLUSTER ein größeres lokales Transport-Netzwerk betrachtet, bei dem CO2 bei geringeren Temperaturen, also vorwiegend im flüssigen Zustand transportiert wird. Wurden in COORAL die CO2-Ströme von Kohlekraftwerken untersucht, ging es in CLUSTER zusätzlich um die Emissionen von relevanten Industrien, deren CO2-Emissionen nicht ohne Weiteres vermieden werden können.
Aufgrund der Erfahrungen in COORAL konnte eine Auswahl von kommerziellen Werkstoffen getroffen werden, die für einen konkreten Einsatz für CCS zur Verfügung stünden. Die gemischten und fluktuierenden CO2-Zusammensetzungen sind bei geeigneten Begrenzungen der Begleit¬stoffe im CO2 bezüglich Korrosionsvorgänge beherrschbar. Die Machbarkeit eines lokalen CCS-Clusters erscheint daher gegeben, soweit dies die Anlagen für Kompression, Transport und Injektion betrifft.