Fire Science
Filtern
Dokumenttyp
- Vortrag (15) (entfernen)
Referierte Publikation
- nein (15)
Schlagworte
- Flame retardant (15) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (15)
A few layer/multilayer graphene (MLG) with a specific surface area of BET ≥ 250 m2/g is proposed as an efficient multifunctional nanofiller for rubbers. The preparation method, i.e., ultrasonically-assisted solution or latex premixing of master batches followed by conventional two-roll milling, strongly influences the dispersion in the elastomeric matrix and is fundamental for the final properties. When homogenously dispersed, single stacks of only approximately 10 graphene sheets, with an aspect ratio of ca. 35, work at low loadings, enabling the replacement of large amounts of carbon black (CB), an increase in efficiency, and a reduction in filler load. The appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing, gas barrier properties, electrical and thermal conductivity, as well as mechanical properties of different rubbers, as shown for chlorine-Isobutylene-Isoprene rubber (CIIR), nitrile-butadiene rubber (NBR), natural rubber (NR), and styrene-butadiene rubber (SBR).[1-5] 3 phr of MLG tripled the Young’s modulus of CIIR, an effect equivalent to 20 phr of CB. The stronger interactions between MLG and NR or SBR also resulted in a reduction in the elongation at break by 20% and 50%, respectively, while the same parameter was hardly changed for CIIR/MLG and NBR/MLG. CIIR/MLG and NBR/MLG were stiffer but just as defomable than CIIR and NBR. The strong reinforcing effect of 3 phr MLG was confirmed by the increase of greater than 10 Shore A in hardness. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards flammability. We investigated MLG also as a synergist for reducing the aluminium trihydrate loading in flame retardant hydrogenated acrylonitrile-butadiene (HNBR), polybutadiene chloroprene (BR/CR), and chlorosulfonated polyethylene rubber(CSM).[6-8] The higher the nanofiller concentration is, the greater the improvement in the properties. For instance, the permeability decreased by 30% at 3 phr of MLG, 50% at 5 phr and 60% at 10 phr, respectively. Moreover, the MLG nanocomposites improve stability of mechanical properties against the effects of weathering. In key experiments an increase in UV-absorption and a pronounced radical scavenging were proved as stabilizing mechanisms. In a nutshell, MLG is an efficient multifunctional nanofiller ready to be used for innovative rubber development.
Renewable alternatives for common thermoset resins are demanded to go for sustainability. The objective is to create a flame retarded epoxy resin from a commercial bio epoxy resin with halogen free inorganic and organic flame retardants, respectively. Alumina trihydrate, aluminum diethyl phosphinate, a DOPO-based phosphonamidate and ammonium polyphosphate seem to have promising performances. Properties are enhanced with different bio fillers: pyrolyzed cocoa shells and plant waste (provided by Otto A. Müller Recycling GmbH, thanks!), short fibers and nonwovens of the natural fiber kenaf, hydroxypropyl-ß-cyclodextrin and sulfobutylether-ß-cyclodextrin.
Fire performance is investigated by cone calorimeter examinations, LOI and UL-94 ratings. Thermal analysis is given by TG-FTIR and DSC measurements.
Combinations of flame retardants and bio-fillers lead to reduced PHRR and THR, reach V0 in UL-94 and have a significant increase in LOI of up to 37 vol.-%. 10 % ammonium polyphosphate with 10 % pyrolyzed cocoa shell performs best, builds a magnificent protective layer, and shows good intumescence.
Das Brandverhalten stellt wie das ausgezeichnete elektrische Isolationsverhalten, die geringen elektrischen Verluste, die Verarbeitbarkeit und Formbarkeit eine der wesentlichen Schlüsseleigenschaften im Eigenschaftsprofil von Polymerwerkstoffen in der Elektronik und der Elektrotechnik dar. Dabei bedarf es einer Ausrüstung der Polymerwerkstoffe mit Flammschutzmittel. Die Entwicklung von immer effizienteren, synergistischen und multifunktionalen Multikomponentensystemen ist dabei eine herausragende Quelle für Innovation. Die Entwicklung und Verbesserung der werkstoff- und anwendungsspezifischen Flammschutzlösungen bestimmen die aktuellen und zukünftigen Polymermaterialien in der Elektronik und Elektrotechnik mit. Der Vortrag stellt anhand von Beispielen einige der erfolgreichen Konzepte dar. Es wird versucht, über das wissenschaftlich-systematische Verständnis Grundprinzipien und vielversprechende Lösungsstrategien zu verdeutlichen.
The presentation gives an overview of actual research adtivities in the field of flame retardant polymers. Details are selected illuminating the scientific topic beyond the state of the art. Different concepts are illustrated with own results obtained in different Research projects over the last 15 years.
Most synthetic polymers have a high fire load, and as a result, they require flame retardants (FRs) to ensure their safe use. Phosphorus plays an important role in flame retardancy and has the potential to replace halogenated variants, which are assumed to be harmful to the environment and health. Among phosphorus-based FRs, there exists a trend towards polymeric, high molar mass molecules with complex molecular architectures. In this project, we synthesized a novel series of so-called phosphorus-based hyperbranched polymeric FRs and investigated their use as multifunctional additives to high-performance polymers, i.e. epoxy resins. By cleverly designing the chemical structure to contain varying amounts of P-O and P-N bonds, new insight into the chemical mechanism of flame retardancy was gained, and by comparing the hyperbranched polymers to their monomeric counterparts, a greater understanding of the role of complex architecture was won. This talk aims at presenting some of these results and proposes chemical mechanisms that illustrate what role these novel hyperbranched flame retardants play in molecular firefighting.
This paper is based mainly on the results of two different projects performed in the group of the author recently (2016-2019). The three external partners involved in these two projects are competent in the preparation of FPUF (ICL IP America), RPUF (Department of Industrial Engineering, Padova University), and TPU (Fraunhofer-Institut für Betriebsfestigkeit und Systemzuverlässigkeit LBF, Darmstadt) as well as for the specimen preparation. Systematically varied sets of materials were prepared as the key basic for scientific discussion, varying the kind and combination of flame retardant, PUR structure, density, and blowing agent.
A multimethodical approach based on thermogravimetry (TGA), TGA coupled with evolved gas analysis (TGA-FTIR) and pyrolysis GC-MS was used for investigating the pyrolysis. The flammability was addressed using oxygen index (OI) and testing in UL 94 burning chamber in vertical and horizontal set-up. The fire behaviour was addressed by using a cone calorimeter. Beyond these methods according to the state of the art, key experiments were performed. We addressed the dripping and the two-stage burning of TPU using a self-designed apparatus and specific data evaluation, the foam burning through quenching burning samples, using different special sample holders, and measuring temperature profiles within the burning foams. The investigation is made round by intensive analysis of the fire residues, such as comprehensive investigation of the morphology.
Result on the pyrolysis (TGA-FTIR, Pyrolysis-GC/MS), flammability (UL 94, LOI), and fire behaviour (cone calorimeter) of TPU and flame retardant TPUs are shown. We discuss in detail the characteristic of PUR decomposition: the low tendency to char, and the specific two step decomposition and how these characteristics control the regimes in fire behaviour. We demonstrate that the different burning regimes are controlled by different pyrolysis products and effective heat of combustions. The resulting formation of pool fires as well as the formation of dripping is discussed in detail. The latter quite important to understand the flame retardancy applied with respect to achieve the UL 94 classification V0 nondripping or V0 non-flaming dripping.
Rigid and flexible PUR foams and their flame retarded versions are investigated for different densities. Water and pentane-blown foams are compared as well as PUR and polyisocyanurate-polyurethane (PIR) foams. Horizontal testing in the cone calorimeter is used and the vertical foam specimen holder as well. Self-designed set-ups within the cone calorimeter enable a better inside in the pyrolysis front running through the foam samples as well as the development of the temperature gradient inside the foam during the fire test. The morphology change during burning was characterised by the means of quenching burning foams with liquid nitrogen and investigating the cross sections with scanning electron microscope. In sum, a rather comprehensive study was performed to work out the principle fire phenomena controlling the fire behaviour of PUR foams in a very systematic and significant way.
Promising flame retardancy approaches are discussed. The importance of either combining the drain of fuel and flame inhibition or charring into an effective protection layer/multicellular structure is underlined.
This contribution focusses the general conclusions and trends. It tries to increase the understanding of the specific and demanding challenge to develop flame retardant PUR materials.
As a potential substitute for currently used halogenated flame retardants we explored the synthesis of dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide (BPPO) and derivatives. BPPO is a cyclic phosphonate and was synthesized by a simple, three-component condensation using 2,2´-biphenol, phosphorus trichloride and water by improving a procedure given by Natchev. Subsequently, BPPO was employed in phospha-Michael additions in line with the known synthesis of DOPO-compounds to double bonds. These reactions result in novel phosphorus-containing compounds with flame retardant activíty. The chemical structure of the unsaturated compounds was systematically varied yielding non-reactive flame retardants (without functional groups) from acrylates and diesters, and reactive (with functional groups) flame retardants from p-benzoquinone. The use of the phosphonate BPPO and its derivatives as flame retarding additives has not been described yet. The BPPO ring is highly reactive. Therefore, it is supposed that it mainly acts in the gas phase.
The new phosphonates were applied as additives for improving the flame retardancy of rigid PUR/PIR foams with triethyl phosphate (TEP) as plasticizer. The foam characteristics like density, cell integrity, pore size and mechanical properties were investigated. The burning properties of the foams were analyzed in the vertical flame spread according to DIN 4102 and by cone calorimetry. The relevant parameters depended on the phosphorus content, which is illustrated for PIR foams with ethyl 3-(6-oxidodibenzo[d,f][1,3,2]dioxaphosphepin-6-yl)propanoate (X, Z = H; Y = OEt; EA-BPPO) as FR additive.
At comparable P-content, the EA-BPPO additive reached the PHHR-values of the benchmark foam with TEP and triphenyl phosphate as FR additive. With increased P-content the values were further reduced. TML and MARHE parameters showed a similar tendency. The FR additives dispersed well in the formulation and had no significant influence on foam density, cell integrity and pore size compared to the reference sample.
Nowadays, various polymeric materials are used in E&E applications with sufficient flame retardance by adding rather different flame retardants. It doesn’t matter whether cables are used outdoor or are installed indoor as building products, the weathering exposures such as UV radiation, humidity and variation in temperature occur and influence the flame-retardant property. Recently, the lifetime of the flame retardance itself becomes an increasingly important factor. In this work, several devices were used to perform accelerated artificial ageing simulating different environment exposures.
The comprehensive and global understanding of the durability of flame retardance in dependence on the weathering or ageing conditions is still a matter of discussion. Therefore, the weathering resistance of various halogen-free fire-retarded polymers was investigated in this work. Polymeric systems with different kinds of fire retardants were chosen, including various fire retardant mechanisms. Ethylene Vinyl Acetate (EVA) blends with high amounts of inorganic flame retardant such as aluminum hydroxide (ATH), boehmite and synergists, which mainly dilutes the polymer resin work as heat sink and cooling agent, and enhance residue formation was examined. Thermoplastic Polyurethane (TPU) was modified with melamine cyanurate (MC), which mainly acts by changed melt flow and dripping behavior as well as fuel dilution. Additionally, aluminum diethylphosphinate and boehmite are induced as assistant flame retardant. Furthermore, glass fiber reinforced Polyamide 66 (PA) was investigated containing different kinds of aluminum diethylphosphinate based flame retardant mixtures, which acts by flame inhibition and additional char formation.
The degradation of the surface was analyzed after the different weathering conditions. Most of the specimens exhibited an intensive material degradation at the top surface accompanied by a distinct discoloration, e.g. getting darker or showing yellowing. The weathering of the EVA samples lead to numerous cracks (already) after 4000 h. The corresponding changes in the chemical structure was investigated by ATR FT-IR for all materials.
The flammability was investigated by cone calorimeter, UL-94 burning chamber, and oxygen index (LOI) using plate and bar specimens. The flame retardance of most of the materials studied degrades only slightly or were rather stable for the investigated exposure times. Interestingly, also some opposite results were found. EVA modified by different inorganic flame retardants such as ATH achieved higher LOI after exposing in the humidity chamber and the accelerated oxidation under water in the autoclaves. It is suggested that the particle size of ATH and boehmite plays an important role, when these flame retardants agglomerate at the surface during accelerated weathering.
Both materials, EVA and TPU, were also investigated as cable jackets. While EVA modified with inorganic flame retardants exhibits low-smoke and non-dripping fire behavior, TPU flame-retarded with MC yields cables with pronounced melt-dripping. Cone calorimeter tests were carried out using cable rafts of the size of 100 mm * 100 mm as well as our self-made cable module test, which simulates the vertical full-scale test of a bundle of cables at the bench-scale. Both methods were used to investigate the weathering resistance of the flame retardance in cables. The results of the cable module test for the flame-retarded EVA cables were only slightly affected even when a long time hydrothermal ageing was carried out. This is because of inorganic residue which just delays the fire growth but does not extinguish. However, for the flame-retarded TPU cable jackets, the cable module test exhibited an accelerated fire spread and a melt-dripping behavior which was promoted by weathering exposure.
Although the main flame retardant modes of action are known, in practise the detailed scientific understanding usually falls short, when it comes to modern multicomponent systems, the important tiny optimizations, or quantifying in terms of specific fire properties. The description of the flame retardant modes of action remains usually vague and fragmentary. This talk tries to deliver thought-provoking impulses how the understanding of the fire behaviour and flame retardancy can be utilized to direct the development of future flame retardant polymer products. Some overseen details are picked up as well as rethinking of concepts memorised long ago is encouraged to discover something new. Furthermore, the talk tries to fill the gap between flame retardant modes of action and fire performance constituting a product. This talk promotes the evidence-based development of flame retardant polymers
Benefits of hyperbranched structure:
Molecular weight, miscibility, number of FR groups, end-group functionalization, glass transition temperature, decreased PBT.
Examples of hyperbranched FRs:
Charring agent, silicone, triazine, etc.
Systematic study of effect of chemical surrounding and impact of Complex shape of phosphorus-based hyperbranched polymers on flame retardant efficacy in epoxy resins.
Elastomers are used in a wide range of automotive and railway applications. However, a severe drawback of most rubbers are their high flammability. Therefore, flame retardants (FRs) are added to improve the performance in fire. Generally, rubber composites are filled with high amounts of mineral fillers such as aluminium trihydroxide (ATH) to fulfil fire safety regulations. These high loadings may cause deterioration of the physical properties of the material. This work shows the implementation of two new strategies to achieve the modern demands on non-toxic FRs and the reduction of fillers.
The first approach was the implementation of multilayer graphene (MLG), acting as a multifunctional filler, reinforcing agent and FR. The study presents filler combinations with a systematic variation of the fillers carbon black (CB), MLG and ATH. The nanocomposites were prepared via master batch by an ultrasonically assisted solution mixing. Afterwards the master batch was compounded into the rubber in a two-roll milling. MLG substituted high amounts of the conventional filler CB, leading to reduced filler loadings and a consistent improvement in curing, mechanical and FR properties.
The second strategy was the combination of phosphorous-containing FRs with a potential new polymeric char promoting agent polyaniline (PANI). Char promoting additives such as pentaerythritol (PER) improve the effectiveness of the FR system. The combination of ammonium polyphosphate (APP) with PER was successfully investigated for natural and styrene-butadiene rubber composites. This work investigates the flame retardancy of the combination of FRs with PANI and its capability to act as a char/barrier promoter in EPDM.
The morphology of the rubbers and homogenously dispersion of MLG was investigated via scanning/transmission electron microscope (SEM/TEM) micrographs. Rheological and mechanical measurements assessed the influence of the fillers on the physical properties of the rubber composites. Characterization via thermogravimetric analysis (TGA) led to a broader understanding of the decomposition. In order to determine the flame retardancy effect of these materials, a multi-methodical approach was selected. Limiting oxygen index (LOI) and UL-94 were used to quantify the flammability of the rubber composites. The cone calorimeter provided information about the fire behaviour in forced flaming conditions. Residues were investigated via elementary analysis and XPS to clarify the composition of the remaining material. Glow-Wire and FMVSS 302 tests revealed significant results in terms of flame retardancy. The flame retardancy investigation of rubber composites, combinations of ATH with MLG and ATH with phosphorous-containing FRs, broaden the horizons of rubber flame retardancy solutions. By examining alternate FR formulations and their effect on mechanical and physical properties of the rubber, new insight into the range of applicable additives for rubber composites may be won.
The need to develop effective flame retardants that retain polymer properties and are safe for consumers and the environment is a continuous challenge for material scientists. While halogenated flame retardants were once commonplace, the shift to non-halogenated materials has steadily progressed due to concerns over impact on health and the environment. One prominent group of flame retardants has become a viable alternative for halogenated materials, namely phosphorus-based flame retardants. The chemical versatility of phosphorus-based flame retardants and the ability to work as reactive or additive compounds makes them ideally suited for modern materials. There exists a trend toward complex, polymeric, and multifunction flame retardants, as these materials show greater flame retardancy performance than low molecular weight counterparts and affect material properties to a much lesser extent.
One group of organophosphorus flame retardants that shows great potential for high-performance polymers like epoxy resins are hyperbranched phosphorus-based polymers. These additives exhibit great miscibility with the polymer matrix and a significantly decreased diffusion through the material, which greatly reduce leaching or blooming out of the matrix. Moreover, the material’s thermal stability remains intact at elevated temperatures due to its low impact on the glass transition temperature. Finally, following market trends and legislation such as the guidelines for the Restriction of Hazardous Substances Directive implemented by REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) in the EU, these macromolecules are non-accumulating, non-toxic and have a lower risk of leeching or blooming from the matrix, further reducing environmental impact.
The work presented herein focusses on two distinct parts studying hyperbranched polymeric flame retardants and their corresponding monomeric compounds.
The first part, involving the low molecular weight components, investigated the role of the chemical surrounding of phosphorus in terms of flame retardant efficacy. Here, a systematic variance of the surrounding of phosphorus was investigated: by changing the ratio of oxygen to nitrogen (4:0 until 1:3), four materials, namely phosphoester (4:0), phosphoramidate (3:1), phosphorodiamidate (2:2), and phosphoramide (1:3), were synthesized, characterized, and finally added to Bisphenol A based epoxy resins (10 wt.-% loading). Pyrolysis investigations showed that low molecular weight components volatize at lower temperatures than the polymer matrix. Additionally, cone calorimeter measurements and TGA-FTIR investigations show trends in respect to FR efficacy in pyrolysis and full flaming conditions.
The second part involves the hyperbranched variants of the monomeric counterparts and investigates the role of complex shape on flame retardant efficacy. By comparing the low to the high molecular weight compounds, the influence of the complex shape becomes apparent and can be quantified. Cone calorimeter measurements show an increase in flame retardancy for some materials, while for others, the mode of action is altered.
By implementing a multi-methodical approach, various flame retardancy aspects, from pyrolysis behavior in the gas and condensed phase, to ignitability / reaction-to-small-flame performance, to action in forced flammability experiments, are identified and quantified, allowing for a clearer understanding of the behavior in fire of these novel flame retardants. By comprehending the roles of chemical composition and complex shape, it opens the path for new and effective multifunctional, polymeric flame retardants with decreased PBT, higher miscibility, and low impact on Tg.
This work is funded by the Deutsche Forschungsgemeinschaft (DFG: SCHA 730/15-1; WU 750/8-1).