S.3 Ökodesign und Energieverbrauchskennzeichnung
Filtern
Erscheinungsjahr
- 2018 (19) (entfernen)
Dokumenttyp
- Vortrag (13)
- Zeitschriftenartikel (4)
- Beitrag zu einem Tagungsband (1)
- Posterpräsentation (1)
Schlagworte
- Ökodesign (5)
- Kreislaufwirtschaft (4)
- Normung (4)
- Energieeffizienz (3)
- Ressourceneffizienz (3)
- Abgasanlage (2)
- Circular economy (2)
- Dunstabzugshauben (2)
- Durability (2)
- Energieverbrauchskennzeichnung (2)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (13)
In this study, the test method EN 14825 for testing air conditioners is validated by verifying the sensitivity of the seasonal energy efficiency ratio SEER (declared on the energy efficiency label) in relation to the nominal cooling capacity Pdesign. Therefore, the two major parts of the test method, the measurement part and the calculation part, were investigated. Measurements were conducted on several single-split units. The calculation part was subjected to a sensitivity analysis in order to identify the properties of an air conditioner which have a strong influence on the SEER. The analysis revealed that the measurement procedure delivers reproducible results. However, the energy consumption in special operating states, the duration in active-mode and seasonal performance values in active mode (SEERon) significantly affect the sensitivity of the SEER. Especially assumption of short operating times for a cooling active mode leads to large changes in the SEER with varying Pdesign. In addition, the range of power of Pdesign turned out to have an increasing impact on the SEER with decreasing Pdesign. For Pdesign values ≤10 kW, which is the most popular type of ACs in the EU, the sensitivity of the SEER increases tremendously.
Especially the determination of the SEER for devices with short operating times in cooling active-mode (350 h) and low values for Pdesign (≤10 kW) cannot be reproduced anymore. In consequence, manufacturer could use the sensitivity of the SEER on Pdesign to artificially “increase” the energy efficiency of their air conditioner for the Energy label about 10 %.
The energy label is a tool that informs the consumer about the energy consumption of certain appliances. The tumble dryer is one of these appliances that were considered relevant for receiving an energy label in the European Union. All classes and values on the energy label are stated by the manufacturers. In order to guarantee that the manufacturers do not cheat and appliances are labeled correctly, the stated values are checked by the market surveillance of each country in compliance verification tests. However, in the case of tumble dryers these compliance verification tests are very expensive and can only be realized for a small sample size out of models which are available on the market. The fewer compliance verification tests are carried out, the higher is the chance that there are incorrectly labeled appliances on the market. Therefore, a modification of the test standard for tumble dryers has been analyzed which would reduce the costs of a performance test by at least 11 %.
Elektro"älter"geräte
(2018)
Seit September 2015 gelten für neue Heizgeräte EU-weit einheitliche Mindeststandards: Heizkessel müssen mindestens den Standard der Brennwerttechnik erreichen (ausgenommen sind B1-Gasetagenheizungen für Mehrfachbelegung). Wird ein alter Wärmeerzeuger ausgetauscht, muss daher stets der Schornstein für die Abgasabführung im Überdruck geeignet sein und gegen Kondensat ertüchtigt werden, also feuchtebeständig sein. Handelt es sich um eine mehrfach belegte Abgasanlage der Arten C4, C8 oder B3, sind alle am Schornsteinstrang angeschlossenen Gasgeräte betroffen. In einem Expertengremium des DVGW wurden Handlungsempfehlungen erarbeitet. Einige Lösungsansätze vermeiden einen sofortigen Austausch aller Geräte an einem gemeinsamen Schornsteinstrang.
Seit September 2015 gelten für neue Heizgeräte EU-weit einheitliche Mindeststandards: Heizkessel müssen mindestens den Standard der Brennwerttechnik erreichen (ausgenommen sind B1-Gasetagenheizungen für Mehrfachbelegung). Wird ein alter Wärmeerzeuger ausgetauscht, muss daher stets der Schornstein für die Abgasabführung im Überdruck geeignet sein und gegen Kondensat ertüchtigt werden, also feuchtebeständig sein. Handelt es sich um eine mehrfach belegte Abgasanlage der Arten C4, C8 oder B3, sind alle am Schornsteinstrang angeschlossenen Gasgeräte betroffen. In einem Expertengremium des DVGW wurden Handlungsempfehlungen erarbeitet. Einige Lösungsansätze vermeiden einen sofortigen Austausch aller Geräte an einem gemeinsamen Schornsteinstrang.
Die Ressourcen der Erde sind nicht nur endlich, sondern werden zudem ineffizient genutzt. Mit dem im Dezember 2015 verabschiedeten Aktionsplan zur Kreislaufwirtschaft fördert die Europäische Kommission den Übergang zur stärker kreislauforientierten Wirtschaft. So werden Anforderungen an Reparaturfähigkeit, Lebensdauer und Recyclingfähigkeit von Produkten zukünftig in der Ökodesign-Richtlinie gesetzt. Die Ökodesign-Richtlinie regelt momentan die Energieeffizienz von energieverbrauchsrelevanten Produkten. Um Anforderungen an den nachhaltigen Einsatz von Ressourcen zu formulieren, fehlen jedoch Normen und Definitionen. Diese Normen werden Momentan geschaffen - erst danach können gesetzliche Anforderungen folgerichtig umgesetzt werden.
The adsorption of water in one-dimensional channels in porous aluminophosphate material AlPO4-5 has been studied by a combination of gravimetric Analysis techniques, neutron and X-ray diffraction and Neutron spectroscopy. Molecular structure of AlPO4-5 consists of 12-membered rings of alternating, corner-sharing AlO4 and PO4 tetrahedra connected by oxygen bridges into sheets in the (a, b) plane. The sheets are connected by oxygen bridges along the c crystal axis and form onedimensional channels of which the largest, formed by the 12-membered rings, have a van der Waals Diameter of about 8.3 Å. Gradually increasing the amount of adsorbed water we could follow the evolution of the confined water mobility in a systematic way and identify the molecular mechanism of water adsorption. We focused particularly on the range of low and medium relative pressures up to p/p0=0.32, where a Change from a hydrophobic behavior to a steep, capillary condensation like water intake has been observed. At the Initial adsorption stages water occupies positions close to the pore walls causing the contraction of channels in the (a, b) plane and the prolongation of the channels along c axis in AlPO4-5. With the progressing intake water molecules form chains along the main channels. The cooperative interactions between water molecules lead to the onset of phonon-like cooperative modes and, surprisingly, to the increase of diffusive-like motion, which slow down only in the final adsorption stages when AlPO4-5 channels are completely filled.