S.3 Ökodesign und Energieverbrauchskennzeichnung
Filtern
Dokumenttyp
- Vortrag (49)
- Zeitschriftenartikel (11)
- Beitrag zu einem Tagungsband (11)
- Sonstiges (2)
- Posterpräsentation (2)
- Dissertation (1)
Schlagworte
- Ökodesign (15)
- Circular Economy (14)
- Kreislaufwirtschaft (13)
- Energy label (11)
- Ressourceneffizienz (11)
- Ecodesign (10)
- Heat pump (9)
- Energieeffizienz (8)
- Energieverbrauchskennzeichnung (8)
- Circular economy (6)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (49)
Several models of range hoods were tested by independent and accredited testing institutes. The results have been compared to the information declared by the manufacturer on the energy efficiency label and the product fiche. The measured electric power input of the lighting System and the measured grease absorption factor often differed significantly from the declared values.
The reasons for these observations and the necessary steps to ensure accurate measurements and a meaningful EU energy efficiency label are elucidated. It is suggested that the ranges of the lighting efficiency classes are readjusted to fit the nowadays prevalent LED technology.
Furthermore the tolerance in the regulation for the nominal electric power input of the lighting could be extended by a minimum absolute tolerance. The grease absorption test method may need a rework to achieve a satisfying accuracy.
Neues Energielabel
(2018)
In this study, the test method EN 14825 for testing air conditioners is validated by verifying the sensitivity of the seasonal energy efficiency ratio SEER (declared on the energy efficiency label) in relation to the nominal cooling capacity Pdesign. Therefore, the two major parts of the test method, the measurement part and the calculation part, were investigated. Measurements were conducted on several single-split units. The calculation part was subjected to a sensitivity analysis in order to identify the properties of an air conditioner which have a strong influence on the SEER. The analysis revealed that the measurement procedure delivers reproducible results. However, the energy consumption in special operating states, the duration in active-mode and seasonal performance values in active mode (SEERon) significantly affect the sensitivity of the SEER. Especially assumption of short operating times for a cooling active mode leads to large changes in the SEER with varying Pdesign. In addition, the range of power of Pdesign turned out to have an increasing impact on the SEER with decreasing Pdesign. For Pdesign values ≤10 kW, which is the most popular type of ACs in the EU, the sensitivity of the SEER increases tremendously.
Especially the determination of the SEER for devices with short operating times in cooling active-mode (350 h) and low values for Pdesign (≤10 kW) cannot be reproduced anymore. In consequence, manufacturer could use the sensitivity of the SEER on Pdesign to artificially “increase” the energy efficiency of their air conditioner for the Energy label about 10 %.
Die Kreislaufwirtschaftsinitiative der Europäischen Kommission fordert klar grundlegende Aspekte der Kreislaufwirtschaft in bereits bestehende Rechtsrahmen einzubetten. Anforderungen zur gesetzlich vorgeschriebenen Lebensdauer, Reparierbarkeit und Recyclingfähigkeit von Produkten sollen zukünftig auf europäischer Ebene ins Leben gerufen werden. Ein geeignetes Spielfeld ist die Ökodesign-Richtlinie. Momentan regelt sie primär die Energieeffizienz von energieverbrauchsrelevanten Produkten, doch der Fokus wird aktuell um Anforderungen an den nachhaltigen Einsatz von Ressourcen erweitert. Bei den gegenwärtigen Aktivitäten im Ökodesign steht der Normungsauftrag M/543 im Zentrum. Es wurde 2015 von der Europäischen Kommission an CEN/CENELEC vergeben und später stieß auch ETSI dazu. Bislang sind acht generische EN-Normen und zwei Fachberichte (Technical Report (TR)) geplant. Sie sollen grundlegende Aspekte der Nachhaltigkeit von energieverbrauchsrelevanten Produkten, die von der Ökodesign-Richtlinie betroffen sind, abdecken. Trotz der zu erwartenden hohen Reichweite dieses Vorhabens scheinen die Inhalte und der eigentliche Zweck der zu erarbeitenden Normen vielen Marktakteuren noch nicht vollständig bekannt zu sein. Daher hat ein nationaler Zentralverband eingeladen zu berichten. In dem Vortrag werden Antworten auf folgende Fragen gegeben: Warum im Ökodesign? Was ist geplant? Was ist betroffen? Worum geht es in den Normen?