9 Komponentensicherheit
Filtern
Erscheinungsjahr
- 2018 (81) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (81) (entfernen)
Schlagworte
- Additive manufacturing (8)
- Friction (7)
- Wear (7)
- Laser metal deposition (6)
- Microstructure (6)
- Niobium carbide (6)
- Residual stress (6)
- High-strength steels (5)
- Laser beam welding (5)
- Cermet (4)
- Welding (4)
- Fracture mechanics (3)
- Laser welding (3)
- Mechanical properties (3)
- Process parameters (3)
- Sintering (3)
- Solidification cracking (3)
- Thick-walled steel (3)
- Weldments (3)
- Alumina (2)
- Crack closure (2)
- DED (2)
- Diffusion (2)
- Dimensional accuracy (2)
- Dissimilar metal weld overlays (2)
- Electromagnetic weld pool support (2)
- Fatigue crack growth (2)
- Fatigue crack propagation (2)
- Fatigue crack propagation threshold (2)
- Fatigue strength (2)
- GMA welding (2)
- Grain size (2)
- Hardness (2)
- Hybrid laser-arc welding (2)
- Hydrogen (2)
- IN718 (2)
- NbC (2)
- Neutron diffraction (2)
- Nickel (2)
- Niobium carbide (NbC) (2)
- Residual stresses (2)
- Restraint (2)
- Selective laser melting (2)
- Short cracks (2)
- Single pass welding (2)
- Solid lubricants (2)
- TPU (2)
- Temperature (2)
- Titanium (2)
- Welding simulation (2)
- 2Disk (1)
- 3D-finite element modeling (1)
- 9%Ni steel (1)
- ADXRD (1)
- AM (1)
- Accelerator magnets (1)
- Adaptive control (1)
- Adaptive welding beam oscillation (1)
- Adhesion (1)
- Alloys (1)
- Aluminium oxide (1)
- Atomic Force Microscopy (1)
- Austenitic (1)
- Automated manufacturing (1)
- Automatisierte Fertigung (1)
- Automotive application (1)
- Beam oscillation (1)
- Behavior (1)
- Beschleunigungssensorik (1)
- Build-up strategy (1)
- Bulging (1)
- CCT diagrams (1)
- CFD model (1)
- Carbon (1)
- Carbon steel (1)
- Carbonitride (1)
- Cell (1)
- Ceramic (1)
- Chemical composition (1)
- Cimensional Accuracy (1)
- Clad steels (1)
- Coarse grained heat affected zone (1)
- Coarse-grained heat-affected zone (1)
- Coating (1)
- Cold-welding (1)
- Composite (1)
- Condition monitoring (1)
- Constraint (1)
- Cooling rate (1)
- Coordinate measurement machine (1)
- Crack closure mechanisms (1)
- Creep resistant steel (1)
- Creep-resistant steel (1)
- Critical strain (1)
- Cryogenic temperature (1)
- Cyclic J-integral (1)
- Cyclic R-curve (1)
- Cyclic R-curve analysis (1)
- Cyclic stress-strain curve (1)
- Cylindrical turning (1)
- DEM (1)
- DIC (1)
- Deformation (1)
- Deformed geometry (1)
- Density measurement (1)
- Deposition rate (1)
- Design of experiments (1)
- Diaspore (1)
- Die-cast aluminum (1)
- Digital Image Correlation (1)
- Digital image correlation (1)
- Digitalisierung (1)
- Digitization (1)
- Dilatometry (1)
- Directed Energy Deposition (1)
- Duplex (1)
- Elastic follow-up (1)
- Elastic-plastic fracture mechanics (1)
- Electrical connectors (1)
- Electro-plated nickel coatings (1)
- Electroless Ni-P (1)
- Electromagnetic influence (1)
- Electromagnetic weld pool support system (1)
- Embedded electronics (1)
- Embrittlement (1)
- Endurance limit (1)
- Equivalent heat source (1)
- Equivalent stress concentration factors (1)
- FEM (1)
- Femtosecond laser (1)
- Femtosecond laser processing (1)
- Ferritic steels (1)
- Ferromagnetic steels (1)
- Fiber laser (1)
- Finite element method (FEM) (1)
- Fracture (1)
- Fracture resistance (1)
- Fresnel reflection (1)
- Full penetration (1)
- Fusion Zone (1)
- Fusion zone size (1)
- Fusion zone, nickel alloys (1)
- GMAwelding (1)
- GMR (1)
- GMR sensors (1)
- GTAW (1)
- Gap bridgeability (1)
- Gap bridging (1)
- Gleeble testing (1)
- Grade S960QL steel (1)
- HSLA (1)
- Hard metals (1)
- Hardmetal (1)
- Heat affected zone (1)
- Heat flow (1)
- Heat-affected zone (1)
- High brightness (1)
- High power (1)
- High power laser beam welding (1)
- High strength steel (1)
- High-power fibre laser (1)
- High-power laser beam (1)
- High-strength steel sheets (1)
- Hochfester Stahl (1)
- Hohlprofilknoten (1)
- Hot cracking test (1)
- Hot steam (1)
- Humidity (1)
- Hybrid laser arc welding (1)
- Hydrogen assisted cracking (1)
- ICP-MS (1)
- Impact absorbed energy (1)
- In situ (1)
- In situ strain (1)
- Inclusions (1)
- Kerbspannungskonzept (1)
- Kitagawa-Takahashi diagram (1)
- LIBS (1)
- LTT Weld Filler Materials (1)
- Laboratory X-ray diffraction (1)
- Large-scale test (1)
- Laser ablation (1)
- Laser keyhole welding (1)
- Laser surfacing (1)
- Laser-hybrid welding (1)
- Laser-induced periodic surface structures (LIPSS) (1)
- Laser-metal-deposition (1)
- Leckage (1)
- Life prediction (1)
- Liquid metal embrittlement (1)
- Liquid phase sintering (1)
- Local critical strain (1)
- Low carbon steel (1)
- Low heat input GMA welding (1)
- Low heat input Gma welding (1)
- Low transformation temperature filler materials (1)
- Lubricated sliding (1)
- MAG welding (1)
- Machining (1)
- Magnetic stray field (1)
- Material modeling (1)
- Measurement (1)
- Melt pool dynamics (1)
- Metal Magnetic Memory (1)
- Microalloyed steels (1)
- Microstructure Tensile strength (1)
- Microstructure and texture (1)
- Misalignment of edges (1)
- Molybdenum disulphide (1)
- Monitoring von Rohrleitungen (1)
- Monotonic and cyclic crack driving force (1)
- Monte-Carlo simulation (1)
- Multi-pass welding (1)
- Multiple crack initiation (1)
- Multiple cracking (1)
- Multiple reflections (1)
- Nanoparticle (1)
- Narrow gap welding (1)
- Natural silver wires (1)
- Neural networks (1)
- Nickel alloys (1)
- Niobcarbid (NbC) (1)
- Notch stress approach (1)
- Novel metrology (1)
- Numerical modelling (1)
- Numerical process simulation (1)
- Numerical simulation (1)
- Numerical welding simulation (1)
- Optical measurement (1)
- Oxidation (1)
- PAEKs (1)
- Partial penetration (1)
- Particle erosion (1)
- Phase transformation (1)
- Photooxidation (1)
- Physical vapor deposition (PVD) (1)
- Pipeline (1)
- Plastic deformation (1)
- Plume heating (1)
- Polymers (1)
- Porosity (1)
- Porosity reduction (1)
- Process chain (1)
- Process simulation (1)
- Pulsed laser beam welding (1)
- R-curve analysis (1)
- Reciprocating sliding (1)
- Resistance spot welding (1)
- Rissbildung (1)
- Rohrbiegeprüfstand (1)
- SLM (1)
- Schadensursachen an Rohrleitungen (1)
- Schallemissionsanalyse (1)
- Schutzgasschweißen (1)
- Schweißnahtgeometrie (1)
- Secondary heat source (1)
- Secondary stresses (1)
- Selektive-laser-melting (1)
- Sensor (1)
- Short crack propagation (1)
- Silicon nitride (1)
- Stainless steels (1)
- Strain rate (1)
- Strain rates (1)
- Strain-rate (1)
- Strength mismatch (1)
- Stress-strain behavior (1)
- Superconducting magnets (1)
- Support configurations (1)
- Surface cracks (1)
- Surface texture (1)
- Synchrotron X-ray diffraction (1)
- Synchrotron diffraction (1)
- TIG (1)
- TIG-welding (1)
- Temperature distribution (1)
- Thermal desorption analysis (1)
- Thermal-desorption spectroscopy (1)
- Thick plates (1)
- Ti-6Al-4V (1)
- Titanium alloy (1)
- Tool (1)
- Tool wear (1)
- Toughness (1)
- Transformable steels (1)
- Transient heat transfer (1)
- Tribofilm (1)
- Tribooxidation (1)
- Tubular joints (1)
- Tungsten carbide (WC) (1)
- Turbine components (1)
- Turning (1)
- UV radiation (1)
- Vacuum (1)
- Vapor recondensation (1)
- Vaporization (1)
- Verschleiß (1)
- Verteilte Faseroptische Sensorik (1)
- Verteilten akustischen faseroptischen Sensorik (1)
- Viscoplasticity (1)
- Wasserstoff (1)
- Wear mechanisms (1)
- Weld geometry (1)
- Weld pool (1)
- Weld pool dynamics (1)
- Weld pool shape (1)
- Weld seam geometry (1)
- Welded joints (1)
- Welding Simulation (1)
- Welding residual stresses (1)
- Werkzeug (1)
- Wärmeführung (1)
- Zerstörungsfreie Prüfung (1)
- Zinc (1)
- a-C:H (1)
- additive (1)
- contour method (1)
- friction (1)
- neutron diffraction (1)
- residual stress analysis (1)
- slip-rolling (1)
- test method (1)
- tribofilms (1)
- wear (1)
- Äquivalente Spannungskonzentrationsfaktoren (1)
- Überwachung von Rohrleitungen (1)
Organisationseinheit der BAM
- 9 Komponentensicherheit (81)
- 9.3 Schweißtechnische Fertigungsverfahren (31)
- 9.4 Integrität von Schweißverbindungen (23)
- 9.5 Tribologie und Verschleißschutz (22)
- 5 Werkstofftechnik (8)
- 8 Zerstörungsfreie Prüfung (6)
- 9.2 Versuchsanlagen und Prüftechnik (5)
- 5.1 Mikrostruktur Design und Degradation (4)
- 8.4 Akustische und elektromagnetische Verfahren (4)
- 5.0 Abteilungsleitung und andere (3)
In order to satisfy the growing requirements towards lightweight design and resource efficiency in modern steel constructions, e.g., mobile cranes and bridges, high-strength steels with typical yield strength ≥ 690 MPa are coming into use to an increasing extent. However, these steels require special treatment in welding. The susceptibility for degradation of the mechanical properties
in the presence of hydrogen increases significantly with increasing yield strength. In case of missing knowledge about how and the amount of hydrogen that is uptaken during welding, hydrogen-assisted cracking (HAC) can be a negative consequence.
Moreover, modern weld technology like the modified spray arc process enables welding of narrower weld seams. In this context,
a reduced number of weld beads, volume, and total heat input are technical and economical benefits. This work presents the influence of welding parameters on the diffusible hydrogen content in both (1) single-pass and (2) multi-layer welds. Different
hydrogen concentrations were detected by varied contact tube distance, wire feed speed, arc length, and varied arc type (transitional
arc and modified spray arc). The results show that all welding parameters have significant influence on the diffusible hydrogen concentration in the single-pass welds. By increasing the number of weld beads in case of multi-layer welding, the
hydrogen concentration has been reduced. Whereby, differences in hydrogen concentrations between both arc types are present.
Partial penetration welding with fiber laser on 20mm thick plates was carried out in horizontal position to study the role of secondary heating in modeling of high power fiber laser welding. Experiments were carried out using 18.8kW laser with 1.5 m/min welding speed at Ar assist gas flow rates of 0, 17, 29, and 40 l/min, all four cases show similar bead shape with bright emission of vapor plume. Numerical simulations were performed using volume of fluid method by considering three different models as models A–C. Model A considers only Fresnel reflection inside the keyhole using real time tracking of free surface. Model B considers vapor recondensation flux inside keyhole along with model A. Finally, model C is used, which considers vapor plume heating at 4100K temperature along with models A B. Secondary heating by recondensation and vapor plume is vital in modeling of high power fiber laser welding; especially, the upper part of the bead is more influenced due to secondary heating. Tungsten particles are also used to visualize the flow pattern of melt pool.
Analytical flaw assessment
(2018)
The paper provides a review on analytical flaw assessment methods with the focus on fracture under monotonic loading and fatigue crack propagation. The first topic comprises linear elastic as well as elastic-plastic fracture mechanics approaches. It essentially follows their historical development. Topics which are separately discussed are reference/Limit loads, the treatment of secondary stresses, strength mismatch, constraint, unstable crack propagation (monotonic R-curve analyses) and statistical aspects. With respect to fatigue crack propagation the analytical treatment of crack closure and constraint and the Determination of the cyclic elastic-plastic crack driving force is discussed. Finally, cyclic Rcurve analyses are briefly addressed.
Research and development of WC grades is 90 years ahead of niobium carbide-based hard materials, which showed already as light-weight and unexplored material a very high potential for many technical applications, especially for wear protection and machining. NbC evoluted recently from lab scale to pilot scale, especially in areas where established WC-based materials are causing economic, environmental or technical concerns. Benchmark trials of NbC-based hard metals indicated already a favorable performance in machining of steel components.
In an increasing number of modern steel applications, high-strength structural steel grades are demanded to meet specifications regarding a high load-bearing capacity and a low operating weight. Lightweight design rules enhance the safety requirements, especially for welded joints. Besides a higher cracking risk for high-strength steel welds, the formation of tensile residual stresses might lead to fracture due to overloading or premature failure if not adequately considered. In this study, a stress-strain analysis was conducted at component-related structures from S960QL using digital image correlation while preheating, welding and cooling adjacent to the weld seam. X-ray diffraction analysis of the local residual stresses in the weld seam showed a good comparability with global analyses using either a DIC system or a special testing facility, which allowed in situ measurements of welding loads. By analysing two different seam geometries, it could be shown that lower multi-axial stresses arise if a narrower weld groove is used. Comparative analyses revealed a direct correlation of the local residual stresses in the weld with transverse shrinkage restraint, whereas the residual stress level in the HAZ is significantly affected by the bending restraint of the weld construction and the occurring bending stresses, respectively.
A three-dimensional multi-physics numerical model was developed for the calculation of an appropriate equivalent volumetric heat source and the prediction of the transient thermal cycle during and after fusion welding. Thus the modelling process was separated into two studies. First, the stationary process simulation of full-penetration keyhole laser beam welding of a 15 mm low-alloyed steel thick plate in flat position at a welding speed of 2 m/min and a laser power of 18 kW was performed. A fixed keyhole with a right circular cone shape was used to consider the energy absorbed by the workpiece and to calibrate the model. In the calculation of the weld pool geometry and the local temperature field, the effects of phase transition, thermo-capillary convection, natural convection and temperature-dependent material properties up to evaporation temperature were taken into account. The obtained local temperature field was then used in a subsequent study as an equivalent heat source for the computation of the transient thermal field during the laser welding process and the cooling stage of the part. The system of partial differential equations, describing the stationary heat transfer and the fluid dynamics, were strongly coupled and solved with the commercial finite element software COMSOL Multiphysics 5.0. The energy input in the transient heat transfer simulation was realised by prescription of the nodes temperature. The prescribed nodes reproduced the calculated local temperature field defining the equivalent volumetric heat source. Their translational motion through the part was modelled by a moving mesh approach. An additional remeshing condition and helper lines were used to avoid highly distorted elements. The positions of the elements of the polygonal mesh were calculated with the Laplace’s smoothing approach. Good correlation between the numerically calculated and the experimentally observed weld bead shapes and transient temperature distributions was found.
In the present work an approach is presented which combines various aspects of the former models with probability considerations. It is used to simulate the impact of more than one billion Alumina particles onto a steel substrate. This approach permits the simulation of an entire erosion experiment on an average PC within about six hours.
Hydrogen-assisted cracking is a critical combination of local microstructure, mechanical load and hydrogen concentration. Welded microstructures of low-alloyed creep-resistant Cr-Mo-V steels show different hydrogen trapping kinetics. This influences the adsorbed hydrogen concentration as well as the diffusion by moderate or strong trapping. A common approach to describe hydrogen traps is by their activation energy that is necessary to release hydrogen from the trap. In the present study, Cr-Mo-V steel T24 (7CrMoVTiB10-10) base material and TIG weld metal were investigated. Electrochemically hydrogen charged specimens
were analyzed by thermal desorption analysis (TDA) with different linear heating rates. The results show two different effects. At first, the microstructure effect on trapping is evident in terms of higher hydrogen concentrations in the weld metal and increased activation energy for hydrogen release. Secondly, it is necessary to monitor the real specimen temperature. A comparison between the adjusted heating rate and the real specimen temperature shows that the calculated activation energy varies by factor two. Thus, the trap character in case of the base material changes to irreversible at decreased temperature. Hence, the effect of the experimental procedure must be considered as well if evaluating TDA results. Finally, realistic temperature assessment is mandatory for calculation of activation energy via TDA.
Schäden an Rohrleitungen können zu hohen Umweltbelastungen und wirtschaftlichen Schäden führen. Um die dauerhafte Verfügbarkeit der Infrastruktur zu gewährleisten, wird im Rahmen des Projekts AGIFAMOR an der Bundesanstalt für Materialforschung und -prüfung (BAM) erprobt, inwiefern das Verfahren der verteilten akustischen faseroptischen Sensorik (Distributed acoustic sensing – DAS) zur kontinuierlichen Überwachung von Rohrleitungen eingesetzt werden kann. Neben der DAS werden erprobte Verfahren der zerstörungsfreien Prüfung wie Schallemissionsanalyse (SEA) und Beschleunigungssensoren eingesetzt. An dieser Stelle soll detailliert auf die Hauptschadensursachen an Rohrleitungen, den Versuchsstand zur mechanischen Belastung von Rohren sowie die Möglichkeiten zu Untersuchungen im Realmaßstab eingegangen werden.
In the present work it was shown that the addition of VC or a combination of VC + Ti(C0.7N0.3) was efficient in reducing the NbC grain growth during liquid phase sintering, when compared to NbC-Ni equivalents. A finest NbC grain size of 1.48 µm was obtained in the NbC-15 Ti(C0.7N0.3)-10 Ni-7.5 VC cermet, exhibiting a hardness of 1486 +/- 7 kg/mm2 and a fracture toughness of 8.7 +/- 0.1 MPa m 1/2.