7.2 Ingenieurbau
Filtern
Dokumenttyp
- Vortrag (169)
- Beitrag zu einem Tagungsband (82)
- Zeitschriftenartikel (65)
- Posterpräsentation (10)
- Buchkapitel (4)
- Dissertation (4)
- Beitrag zu einem Sammelband (3)
- Tagungsband (Herausgeberschaft für den kompletten Band) (1)
- Sonstiges (1)
Sprache
- Englisch (257)
- Deutsch (81)
- Mehrsprachig (1)
Schlagworte
- Structural Health Monitoring (25)
- Ground vibration (20)
- Structural health monitoring (15)
- Fatigue (14)
- Brücken (11)
- Monitoring (11)
- Offshore (11)
- Offshore wind energy (11)
- Hammer impact (9)
- Impact (9)
- Train passage (9)
- Damage characterization (8)
- Model interpolation (8)
- Planar tomography (8)
- SHM (8)
- Structural systems (8)
- Vibration measurements (8)
- Building vibration (7)
- Damage detection (7)
- Deterioration (7)
- Layered soil (7)
- Reliability (7)
- Slab track (7)
- Soil-structure interaction (7)
- Train-induced ground vibration (7)
- Bahnerschütterungen (6)
- Compressive strength (6)
- Design methods (6)
- Grout (6)
- Inspection (6)
- Numerical modelling (6)
- Offshore wind turbines (6)
- Physical phenomenology (6)
- Pile foundations (6)
- Reinforced concrete structure (6)
- Environmental effects (5)
- Interface (5)
- Layered soils (5)
- Modalanalyse (5)
- Numeric simulation (5)
- Repair (5)
- Temperature rejection (5)
- Ultrasonic testing (5)
- Vibration (5)
- Windenergie (5)
- Bayesian updating (4)
- Container loading (4)
- Crack detection (4)
- Damage localization (4)
- Datenmanagement (4)
- Drop test (4)
- Erosion (4)
- Erschütterungen (4)
- Erschütterungsminderung (4)
- Excitation forces (4)
- Fault detection (4)
- Foundation load (4)
- Foundations (4)
- Gründungsstrukturen (4)
- High-strength concrete (4)
- Inspection planning (4)
- Mitigation (4)
- Offshore geomechanics (4)
- Shell Buckling (4)
- Statistical tests (4)
- Steel structures (4)
- Subspace methods (4)
- Subspace-based method (4)
- Tunnel (4)
- Vehicle-track-soil interaction (4)
- Vibration measurement (4)
- Wind (4)
- Wind Energy (4)
- Ansys Autodyn (3)
- Attenuation (3)
- Axle impulses (3)
- BIM (3)
- Bauwerksüberwachung (3)
- Belastungsversuch (3)
- Box-Behnken (3)
- Bridge (3)
- Bridges (3)
- Buckling (3)
- Compaction Grouting (3)
- Cracks (3)
- DUCON® (3)
- Deep foundations (3)
- Dispersionsmessung (3)
- Drucker-Prager (3)
- Ductility (3)
- E-modulus (3)
- Earth masonry (3)
- Elastische Gleiselemente (3)
- Emission (3)
- Erschütterungsprognose (3)
- Filter effects (3)
- Fly ash (3)
- Grouted connection (3)
- Grouting (3)
- Großer Fallturm Horstwalde (3)
- Irregular soil (3)
- Leichtbau (3)
- Linear parameter varying systems (3)
- Load vector (3)
- Maintenance (3)
- Material moisture (3)
- Metakaolin (3)
- Micro-reinforcement (3)
- Micromechanical modelling (3)
- Mobile elements (3)
- Monopiles (3)
- Numerical modeling (3)
- Offshore Pile Foundation (3)
- Offshore Windenergieanlagen (3)
- Offshore foundations (3)
- Offshore wind turbine (3)
- Physical testing (3)
- Post-impact evaluation (3)
- Probabilistic (3)
- Quasi-static and dynamic tests (3)
- Railway (3)
- Railway bridge (3)
- Randomly heterogeneous soil (3)
- Rehabilitation (3)
- Reinforced concrete (3)
- Risk (3)
- Scattering (3)
- Schwingungsdynamik (3)
- Soil erosion (3)
- Soil properties (3)
- Statistical evaluation (3)
- Statistical method (3)
- Stereo photogrammetry (3)
- Subspace-based residual (3)
- System Identification (3)
- Temperature effects (3)
- Train speed (3)
- UHPC (3)
- Vehicle-track interaction (3)
- Vibrations (3)
- Wellenausbreitung (3)
- Wellengeschwindigkeit (3)
- Zivile Sicherheit (3)
- 2-span bridge (2)
- AISTEC (2)
- Acceleration sensors (2)
- Achsfolgespektren (2)
- Acoustic emission testing (2)
- Amplitude-charge weight laws (2)
- Amplitude-distance laws (2)
- Analysis of variance (2)
- Apartment building (2)
- Artificial Intelligence (2)
- Artificial intelligence (2)
- Automatisierte schweißtechnische Fertigung (2)
- Axle sequence (2)
- Axle-sequence spectrum (2)
- Ballast track (2)
- Bauteile (2)
- Bauwerke (2)
- Bauwerksmonitoring (2)
- Bayes'sche Analyse (2)
- Bayesian System Identification (2)
- Bayesian analysis (2)
- Bayesian methods (2)
- Bayesian system identification (2)
- Bemessung (2)
- Big Data (2)
- Bitumen (2)
- Bodenübertragungsfunktion (2)
- Brücke (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Changing process noise (2)
- Chemisoprtion (2)
- Climate chamber (2)
- Compressive Cyclic loading (2)
- Compressive cyclic loading (2)
- Computer Vision (2)
- Concrete (2)
- Coupled fluid-particle simulation (2)
- Coupler systems (2)
- Crack Luminescence (2)
- Crack formation (2)
- Crack pattern (2)
- Cyclic load (2)
- DEM (2)
- Damage identification (2)
- Design (2)
- Digital twin (2)
- Digitalisierung (2)
- Displacements (2)
- Drone (2)
- Earth block masonry (2)
- Elastische Elemente (2)
- Elastische Gebäudelagerung (2)
- Energy (2)
- Erschütterungsausbreitung (2)
- Evaluation (2)
- Explosion-induced ground vibrations (2)
- Faseroptik (2)
- Feuchte (2)
- Finite Elemente Simulation (2)
- Finite element models (2)
- Freight train (2)
- GPU parallel computation (2)
- Gleiströge (2)
- Ground vibration measurements (2)
- Grouted Connection (2)
- Halbraum (2)
- High-performance computing (2)
- High-speed (2)
- High-speed train (2)
- Immission (2)
- Injection Sequence (2)
- Irregular ballast (2)
- Irregularities (2)
- Jacket support structure (2)
- Jet erosion test (2)
- Klimakammer (2)
- Knudsen effect (2)
- LBM-DEM (2)
- Laboratory beam structure (2)
- Lehm (2)
- Long-term shrinkage (2)
- Luminescence (2)
- Macromechanical Sample Strength (2)
- Material tests (2)
- Mauerwerk (2)
- Measurement (2)
- Measurements (2)
- Messen im Bauwesen (2)
- Micro silica (2)
- Micromechanical Tensile Failure (2)
- Mix design (2)
- Modal Analysis (2)
- Model Updating (2)
- Model updating (2)
- Moisture (2)
- Moisture content (2)
- Molecular diffusion (2)
- Non destructive testing (2)
- Non-Destructive Evaluation (2)
- Non-destructive testing (2)
- Numerical model (2)
- Office tower (2)
- Offshore Wind (2)
- Offshore Wind Energy (2)
- Offshore Windenergy Pile Buckling (2)
- Offshore geotechnics (2)
- Offshore wind (2)
- Offshore-Windenergieanlagen (2)
- Optimal Sensor Placement (2)
- Passenger train (2)
- Physisorption (2)
- Pile Foundation (2)
- Pile Tip Buckling (2)
- Prediction (2)
- Prediction of explosion induced ground and building vibration (2)
- Probability of Detection (2)
- Prädiktive Instandhaltung (2)
- Radar (2)
- Railway tunnel (2)
- Railways (2)
- Rechenmodelle (2)
- Reinforcement (2)
- Relative humidity (2)
- Repowering (2)
- Research data management (2)
- Residual evaluation (2)
- Resonance (2)
- Risslumineszenz (2)
- SDDLV (2)
- Safety (2)
- Scattered axle impulses (2)
- Schadensdetektion (2)
- Schwingungsbasierte Verfahren (2)
- Size effect (2)
- Slenderness effect (2)
- Soil-Structure-Interaction (2)
- Soil-pile interaction (2)
- Soil-wall-floor model (2)
- Static axle loads (2)
- Static load (2)
- Strength (2)
- Strukturmonitoring (2)
- Suction bucket (2)
- Supplementary cementitious materials (2)
- Surface-tunnel reduction (2)
- Tensile Capacity (2)
- Time-variant reliability (2)
- Tomographic damage evaluation (2)
- Track damage (2)
- Track-soil interaction (2)
- Train excitation (2)
- Transmission (2)
- Umwelteinflüsse (2)
- Uncertainty (2)
- Uncertainty in reference (2)
- Uncertainty quantification (2)
- Unterraummethoden (2)
- Value of Information (2)
- Vehicle–track interaction (2)
- Verkehrsinfrastukturen (2)
- Vollraum (2)
- Wellenausbreitung in der Tiefe (2)
- Wind Turbines (2)
- Wind energy (2)
- Wind turbine tower (2)
- Windenergieanlagen (2)
- Windenergy (2)
- Zuggeschwindigkeit (2)
- Zuverlässigkeit (2)
- 3D imaging (1)
- Achsimpulse (1)
- Acoustic emission (1)
- Acoustic emission analysis (1)
- Ambient excitation (1)
- Amplituden-Abstands-Gesetze (1)
- Analytical Design Methods (1)
- Asphalt (1)
- Assessment (1)
- Asymptotic local approach (1)
- Automated Modal Analysis for Tracking Structural Change during Construction and Operation Phases (1)
- Automated operational modal analysis (1)
- Automatic modal parameters identification (1)
- Automatisierte Fertigung (1)
- Automatisierte schweißtechniche Fertigung (1)
- Autonomous underwater vehicles (1)
- Axial load bearing (1)
- Axle loads (1)
- Axle pulses (1)
- BAM Windenergie Fügetechnik (1)
- Bahngleis (1)
- Base isolation (1)
- Baugrunddynamik (1)
- Bauwerk-Boden-Wechselwirkung (1)
- Bauwerksdiagnostik (1)
- Beanspruchungszustand (1)
- Belastungsfahrt (1)
- Belastungstest (1)
- Belastungszug (1)
- Benchmark (1)
- Beton (1)
- Betonautobahn (1)
- Betonautobahnen (1)
- Beulen (1)
- Bewertung (1)
- Bionik (1)
- Blast (1)
- Blast tests (1)
- Bodenschlitz (1)
- Bodenvariabilität (1)
- Boundary element (1)
- Boundary element method (1)
- Bridge monitoring (1)
- Bridge resonance (1)
- Bridge vibration (1)
- Bruchlastwechselzahlen (1)
- Brückensicherheit (1)
- Buckling piles circular shells (1)
- Buckling soil-structure-interaction offshore piles track (1)
- Building and Construction (1)
- Building information modelling (1)
- Building response (1)
- Bulging (1)
- CFD (1)
- Cancellation (1)
- Cars (1)
- Cement-based composites (1)
- Centerline solidification cracking (1)
- Chemisorption (1)
- Civil and Structural Engineering (1)
- Civil structures (1)
- Climate Chamber (1)
- Coating (1)
- Cohesive granular materials (1)
- Cohesive soils (1)
- Column/wall resonance (1)
- Combined finite-element boundary-element method (1)
- Compaction grouting (1)
- Compliance function (1)
- Components of excitation (1)
- Compression tests (1)
- Computational (1)
- Condensed Matter Physics (1)
- Conductor (1)
- Continuous soil (1)
- Continuously inhomogeneous geological media (1)
- Continuously inhomogeneous soils (1)
- Crack (1)
- Crack damage detection (1)
- Crack growth (1)
- Crack repair (1)
- Cyber security (1)
- Cyclic axial shearing (1)
- Cyclic degradation (1)
- DEM-LBM simulation (1)
- Damage Detection (1)
- Damage Identification (1)
- Damage evolution (1)
- Decision matrix analysis (1)
- Deckeneigenfrequenzen (1)
- Deckenschwingungen (1)
- Design models (1)
- Design practice (1)
- Detection (1)
- DiMoWind RDS-PP Maintenance Digital Twin Offshore Wind Energy (1)
- Digital Image Correlation (1)
- Digital Image Correlation (DIC) (1)
- Digital Models (1)
- Digital Twin (1)
- Digitale Zwillinge (1)
- Discrete Element Method (1)
- Discrete element method (1)
- Drop Test (1)
- Drop Tests (1)
- Drop tower (1)
- Druckfestigkeit (1)
- Druckschwellenversuch (1)
- Dynamic axle loads (1)
- Dynamic excitation (1)
- Dynamic loads (1)
- Dynamic soil properties (1)
- Dynamische Bodenkennwerte (1)
- Dynamische Bodensteifigkeit (1)
- Dämpfung (1)
- EERA Joint Program (1)
- Earth (1)
- Earth blocks (1)
- Earth material (1)
- Earthen hydraulic constructions (1)
- Earthen hydraulic infrastructures (1)
- Einflusslinie (1)
- Einflusslinien (1)
- Einfügungsdämmung (1)
- End-of-life decision making (1)
- Entscheidungsfindung (1)
- Environmental (1)
- Environmental Effects (1)
- Environmental and Operational Variability (1)
- Environmental changes (1)
- Environmental influence (1)
- Erhaltungsmanagement (1)
- Ermüdung (1)
- Ermüdungsprüfung (1)
- Ermüdungsschäden (1)
- Ermüdungsverhalten (1)
- Erneuerbare Energien (1)
- Erosion of cohesive soils (1)
- Erschütterungen im Fernfeld (1)
- Estimation (1)
- FEM (1)
- FEM analysis (1)
- Fahrzeug-Fahrweg-Boden-Wechselwirkung (1)
- Fallturm (1)
- Fatigue damage (1)
- Fatigue deterioration (1)
- Fatigue strength (1)
- Fault detectionchanging (1)
- Features (1)
- Fequency domain (1)
- Fiber optic sensing (1)
- Fibre optic sensors (1)
- Finite element (1)
- Finite element analysis (1)
- Finite element method (1)
- Finite element model updating (1)
- Finite elements (1)
- Finite-Elemente-Modellkalibrierung (1)
- Finite-element boundary-element method (1)
- Flexibility (1)
- Flexible car body (1)
- Flexible wheelset (1)
- Floor resonance (1)
- Floors (1)
- Fluid-structure interaction (1)
- Footbridge (1)
- Force reconstruction (1)
- Foundation Pile (1)
- Foundation reliability analysis (1)
- Freileitung (1)
- Frequency response function (1)
- GMNIA (1)
- GNSS (1)
- GPA (1)
- GPU Parallel computing (1)
- GPU parallelisation (1)
- Gebäudelagerung (1)
- Gebäudemodelle (1)
- Gebäudeschwingungen (1)
- Gekoppelte Fluid-Partikel Simulationen (1)
- General Materials Science (1)
- Geology (1)
- Geomechanics (1)
- Geomechanics of offshore foundations (1)
- Geometric vehicle and track irregularities (1)
- Geometrie (1)
- Global ambient vibrations (1)
- Granular Cohesive Materials (1)
- Granular Cohesive Materials, (1)
- Granular cohesion (1)
- Ground (1)
- Grout Injection (1)
- HAZID (1)
- HTLS (1)
- Hard impact (1)
- Harter Anprall an Stahlbetonstrukturen (1)
- High-Rise Building (1)
- High-rise building (1)
- High-rise buildings (1)
- Horizontal stress (1)
- Horizontal wind turbine (1)
- Hydraulic jet erosion (1)
- IEPE (1)
- Impact damage of reinforced concrete (1)
- Impact damage on reinforced concrete (1)
- Impact loading (1)
- Impakt (1)
- Impedanzmethode (1)
- Imperfektion (1)
- Impinging jet (1)
- Inclination angle (1)
- Inertial Interaction (1)
- Inertial interaction (1)
- Inhomogeneous soils (1)
- Innovative Messtechnik (1)
- Inspeciton (1)
- Inspektion (1)
- Interface model (1)
- Jet impingement (1)
- Kinematic Interaction (1)
- Kinematic interaction (1)
- Kraft auf den Boden (1)
- LBM-DEM coupling (1)
- LBM-DEM simulation (1)
- Laminar flow (1)
- Laminography (1)
- Large components (1)
- Laser beam welding (1)
- Lateral dynamic displacement (1)
- Lateral load bearing (1)
- Lattice Boltzmann Method (1)
- Lattice Boltzmann method (1)
- Leichtbauprinzipien (1)
- Lifetime Extension (1)
- Load Test (1)
- Load bearing behaviour (1)
- Load identification (1)
- Load tests (1)
- Load-bearing (1)
- Load-bearing behaviour (1)
- Local approaches (1)
- Long-span bridge (1)
- Low-frequency shaker (1)
- MEMS (1)
- Maintal Bridge Gemuenden (1)
- Maintalbrücke Gemünden (1)
- Maintenance Digital Twin Offshore Wind Energy (1)
- Marine geomechanics (1)
- Marine geotechnics (1)
- Maschinenbetrieb (1)
- Maschinenfundament (1)
- Material Point Method (1)
- Material Point Method (MPM) (1)
- Material model (1)
- Measurement campaigns (1)
- Mechanical challenges (1)
- Merkblatt (1)
- Messfahrt (1)
- Microfine Cement (1)
- Microfine cement (1)
- Micromechanical LBM-DEM simulation (1)
- Micromechanical analysis (1)
- Micromechanical simulation (1)
- Microsilica (1)
- Minderungsmaßnahmen (1)
- Mixed formulation (1)
- Modal analysis (1)
- Modal force spectrum (1)
- Modal load spectrum (1)
- Modal system identification (1)
- Model Building (1)
- Model Update (1)
- Model update (1)
- Modell-Update (1)
- Modellierung (1)
- Modes (1)
- Modes and waves (1)
- Modulus of elasticity (1)
- Monitoring-informed inspection and maintenance planning (1)
- Monopile (1)
- Monopile Buckling (1)
- Monopile installation risks (1)
- Movin load test (1)
- Multi-beam method (1)
- Multi-beam track model (1)
- Multiple impact (1)
- NDT (1)
- Nachgiebigkeiten (1)
- Nelson’s method (1)
- Normung (1)
- Numerical analysis (1)
- Numerical damage simulation (1)
- Numerical simulation (1)
- Numerical simulation of impact damage (1)
- Numerical simulations (1)
- Numerische Analysen (1)
- Obstacles (1)
- Offhore (1)
- Office building (1)
- Offshore Structures (1)
- Offshore Wind Energy Converter (1)
- Offshore Windenergie (1)
- Offshore pile foundation (1)
- Offshore pile foundations (1)
- Offshore steel structures (1)
- Offshore wind energy foundations (1)
- Offshore wind farm (1)
- Offshore wind farms (1)
- Offshore wind-turbine foundations (1)
- Offshore-Wind (1)
- Offshore-Windkraftanlagen (1)
- Operational Modal Analysis (1)
- Optimal sensor placement (1)
- Optimierungsmethoden (1)
- Optimization techniques (1)
- Perfectly Matched Layer (PML) (1)
- Pfahlfußbeulen (1)
- Pfahlnachgiebigkeiten (1)
- Physisoprtion (1)
- Piaui state (1)
- Pile Buckling (1)
- Pile Capacity (1)
- Pile ageing (1)
- Pile bending stiffness (1)
- Pile foundation (1)
- Pile groups (1)
- Pile retrofit system (1)
- Pile-Tip-Buckling (1)
- Point Cloud (1)
- Predictive maintenance (1)
- Pressure (1)
- Probabilistic modelling (1)
- Probabilitische Ingenieurmodelle (1)
- Probability of detection (1)
- Probekörpergeometrien (1)
- Process noise (1)
- Prognose (1)
- Propagation from a tunnel (1)
- Quasi-static response; (1)
- Rail roughness (1)
- Railbridge (1)
- Railway induced vibration (1)
- Railway track (1)
- Railway tracks (1)
- Railway trafiic (1)
- Randelementmethode (1)
- Random dynamics and vibrations (1)
- Random stiffness variation (1)
- Rayleighwellendispersion (1)
- Rechenverfahren (1)
- Recovery experiments (1)
- Referenzbeispiel (1)
- Remote sensing vibrometer (1)
- Residential building (1)
- Richtige Fahrzeugmasse (1)
- Richtlinie (1)
- Rigid vehicle model (1)
- Risiko (1)
- Risikoanalyse (1)
- Risk-based design (1)
- Risk-based maintenance planning (1)
- Rissprozes (1)
- Rissprozess (1)
- SHCC (1)
- SHM Environmental (1)
- SHM environmental bridges (1)
- Sandstone (1)
- Santa-marta (1)
- Scaling (1)
- Schadensüberwachung (1)
- Scherwellengeschwindigkeit (1)
- Schienenfahrweg (1)
- Schienenfahrwege (1)
- Schrauben (1)
- Schubmodul (1)
- Schwingungsmessungen (1)
- Schwingungsmonitoring (1)
- Schädigungsprozesse (1)
- Sensitivity vectors (1)
- Serra da cangalha (1)
- Shearing (1)
- Shell buckling (1)
- Shrinkage (1)
- Shrinkage Reducing Admixture (1)
- Sicherheit (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Simulation and experiment (1)
- Site-characterization (1)
- Soft impact (1)
- Soft track elements (1)
- Soil Struture Interaction (1)
- Soil forces (1)
- Soil stiffness (1)
- Soil-building interaction (1)
- Soil-building resonance (1)
- Soil-wall floor model (1)
- Soil-water-structure interaction (1)
- Sorption isotherm (1)
- Spatially varying ground conditions (1)
- Spektralanalyse (1)
- Stability Buckling soil-structure-interaction piles offshore (1)
- Stabilität (1)
- State of stress (1)
- Static loading (1)
- Statistical correlations (1)
- Statistical pattern recognition (1)
- Statistische Auswertung (1)
- Statistische Korrelationen (1)
- Stiffness variation (1)
- Stochastic Subspace Damage Detection (1)
- Strain (1)
- Stress stiffening (1)
- Stress-strain relation (1)
- Stress–strain-relation (1)
- Structural Systems (1)
- Structural integrity (1)
- Structural integrity maintenance (1)
- Structural integrity management (1)
- Structural system identification (1)
- Störgrößen (1)
- Substructures (1)
- Suction Bucket (1)
- Superplasticizer (1)
- Supplementary Cementitious Materials (1)
- Support structures (1)
- Surface Foundation (1)
- Surface line (1)
- Sustainable binders (1)
- Switch (1)
- System identification (1)
- Systemidentifikation (1)
- TOP (1)
- TRC (1)
- Tagung (1)
- Temperature effect (1)
- Temperature effect rejection (1)
- Temperature modeling (1)
- Temperatureinflüsse (1)
- Tensile test (1)
- Test specification (1)
- Tip Buckling (1)
- Track and vehicle irregularities (1)
- Track beam (1)
- Track damage monitoring (1)
- Track damage quantification (1)
- Track deflection (1)
- Track displacements (1)
- Track filter (1)
- Track filtering (1)
- Track vibration (1)
- Tragfähigkeit (1)
- Tragstrukturen (1)
- Train configuration (1)
- Train passages (1)
- Train-induced vibration (1)
- Tran speed (1)
- Transfer fuction (1)
- Transfer function (1)
- Transverse butt weld (1)
- Trench (1)
- Truss structures (1)
- Tunnel line (1)
- Tunnel-pile transfer (1)
- Tunnel-to-surface reduction (1)
- Tunnelstrecke (1)
- Turnout (1)
- UAS (1)
- Un- certainty (1)
- Unbounded domain (1)
- Under-sleeper pads (1)
- Value of information (1)
- Variational Bayesian statistics (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Varying track stiffness (1)
- Vibration analysis (1)
- Vibration excitation (1)
- Vibration monitoring (1)
- Viscosity (1)
- Vorspannung (1)
- Wahrscheinlichkeit (1)
- Water Science and Technology (1)
- Water-structure interaction (1)
- Wave propagation (1)
- Wave-Tower interaction (1)
- Wavenumber domain (1)
- Wavenumber integrals (1)
- Wavenumber method (1)
- Waves (1)
- Weld imperfections (1)
- Welded (1)
- Wellenfeldberechnung (1)
- Wheelset (1)
- Wheelset accelerations (1)
- Wind Energy Structures (1)
- Wind energy tower (1)
- Wind turbines (1)
- Wind-farm aerodynamics (1)
- Windenergieanlage (1)
- Windfarm wake analysis (1)
- Workability (1)
- Zerstreute Achsimpulse (1)
- building information modelling (1)
- elastische Gebäudelagerungen (1)
- fachwerkartige Stahltragwerken (1)
- layered soil (1)
- risk, reliability, inspection planning, offshore wind turbines (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- temperature (1)
- zerstreute Achslastimpulse (1)
- Übertragungsmatrizen (1)
- Überwachung (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (339)
- 7 Bauwerkssicherheit (336)
- 8 Zerstörungsfreie Prüfung (25)
- 7.4 Baustofftechnologie (23)
- 7.1 Baustoffe (12)
- 8.5 Röntgenbildgebung (8)
- 7.0 Abteilungsleitung und andere (6)
- 9 Komponentensicherheit (6)
- 3 Gefahrgutumschließungen; Energiespeicher (5)
- 3.3 Sicherheit von Transportbehältern (5)
- 8.2 Zerstörungsfreie Prüfmethoden für das Bauwesen (5)
- 8.6 Faseroptische Sensorik (5)
- 9.3 Schweißtechnische Fertigungsverfahren (5)
- 8.0 Abteilungsleitung und andere (4)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (4)
- 2 Prozess- und Anlagensicherheit (2)
- 2.4 Prüfung und Bewertung von Explosivstoffen/Pyrotechnik (2)
- 2.5 Konformitätsbewertung Explosivstoffe/Pyrotechnik (2)
- VP Vizepräsident (2)
- VP.1 eScience (2)
- 5 Werkstofftechnik (1)
- 5.3 Polymere Verbundwerkstoffe (1)
- 7.3 Brandingenieurwesen (1)
- 7.6 Korrosion und Korrosionsschutz (1)
- 7.7 Modellierung und Simulation (1)
- 8.3 Thermografische Verfahren (1)
- 8.4 Akustische und elektromagnetische Verfahren (1)
- 9.4 Integrität von Schweißverbindungen (1)
Paper des Monats
- ja (5)
Owners or operators of offshore wind farms perform inspections to collect information on the condition of the wind turbine support structures and perform repairs if required. These activities are costly and should be optimized. Risk-based methods can be applied to identify inspection and repair strategies that ensure an optimal balance between the expected total service life cost of inspection and repair, and the achieved risk reduction. Such an optimization requires explicit modeling of repairs. In this paper, the impact of different repair models on the results of a risk-based optimization of inspection and repair strategies is quantified in a numerical example considering a jacket-type steel frame subject to high-cycle fatigue. The example showed that, in this specific application, there is no need for detailed modeling of the behavior of repaired welded connections.
The Bundesanstalt für Materialforschung und -prüfung (BAM) collaborates with TNO to develop a software framework for automated calibration of structural models based on monitoring data. The ultimate goal is to include such models in the asset management process of engineering structures. As a basis for developing the framework, a multi-span road bridge consisting of ten simply supported steel box girders was selected as a test case. Our group measured output-only vibration data from one box girder under ambient conditions. From the data, we determined eigenfrequencies and mode shapes. In parallel, we developed a preliminary structural model of the box girder for the purpose of predicting its modal properties. In this contribution, we provide an overview of the measurement campaign, the operational modal analysis, the structural modeling and qualitatively compare the identified with the predicted modes. As an outlook, we discuss the further steps in the calibration process and future applications of the calibrated model.
Brücken werden durch Inspektionen und teilweise durch Monitoring überwacht, um Daten und Informationen über den Zustand und die Einwirkungen zu sammeln. Auf deren Grundlage werden Entscheidungen hinsichtlich Maßnahmen zur Gewährleistung der Sicherheit und Verfügbarkeit getroffen. In diesem Vortrag werden die Potentiale der Digitalisierung zur Unterstützung und Verbesserung der Brückenüberwachung diskutiert. Insbesondere werden die Bereiche Datenmanagement, Brückenmodellierung und Entscheidungsfindung betrachtet.
The EU member states have set out ambitious long-term goals for deploying offshore wind energy. The installed offshore wind capacity is set to increase from 14.6 GW in 2021 to around 320 GW in 2050. This signifies the role of offshore wind energy as a major contributor to reaching the EU’s climate and energy goals. To ensure that the defined targets are met, a significant number of new wind farms has to be installed and existing wind farms reaching the end of their planned life need to be reused efficiently. Some of the relevant reuse alternatives are lifetime extension, repowering based on the existing support structures and repowering with new turbines.
As a basis of the decision-making regarding the reuse of existing offshore wind farm, the expected utility of each relevant option should be determined based on the associated expected rewards, costs and risks. The optimal concept maximizes the utility of the decision-maker and fulfills the existing constraints and requirements. To facilitate such a quantitative decision-making, models and methods have to be developed. In particular, models are required that enable predictions of (a) the condition and performance of the turbines and support structures and (b) the renumeration, costs and consequences of adverse events. These predictions have to consider (a) the governing uncertainties, (b) the available information from the planning, construction, installation and operating phase, (b) potential repair, retrofitting and strengthening schemes and (c) possible monitoring, inspection and maintenance regimes for the future operating phase.
Over the past years, several models, methods and tools have been developed at the Bundesanstalt für Materialforschung und -prüfung (BAM) to support the structural integrity management of offshore wind turbine substructures. These include:
(a) a prototype for reliability-based, system-wide, adaptive planning of inspections of welded steel structures in offshore wind farms,
(b) a method for monitoring and risk-informed optimization of inspection and maintenance strategies for jacket structures subject to fatigue, and
(c) a probabilistic cost model of inspection and maintenance of welded steel structures in offshore wind farms.
This contribution provides an overview on these works and discusses how they can be adapted and extended to support the decision-making regarding lifetime extensions and repowering of offshore wind farms.
In this contribution, we consider two applications in which probabilistic approaches can potentially complement or enhance the design and assessment of offshore wind turbine foundations. First, we illustrate in a numerical example that probabilistic modelling can be helpful in dealing with chang-es in turbine locations during the planning phase of an offshore wind farm. In this case, spatial probabilistic modelling of the ground conditions enables (a) an inference of the soil properties at the modified turbine location from field data collected at different locations across an offshore wind farm site and (b) an optimisation of further site investigations. Second, we discuss the uncer-tainties and risks associated with the installation of large diameter monopiles in soils with hetero-geneities such as strong layers and/or embedded boulders. Subsequently, we present a concept for modelling, understanding, and managing these risks based on a probabilistic model of the subgrade conditions, monopile, and subgrade-pile-interaction.
Monitoringsysteme erfassen kontinuierlich Bauwerksdaten wie z.B. Bauwerksbeschleunigungen, auf deren Grundlage Bauwerksschäden mit Hilfe von SHM-Methoden quantifiziert werden können. Mit den gewonnenen Informationen über den aktuellen Bauwerkszustand können Vorhersagen des Bauwerkszustandes und der Bauwerkszuverlässigkeit aktualisiert und erforderliche Inspektionen und Instandhaltungsmaßnahmen vorausschauend geplant werden. Im BMBF-Forschungsvorhaben AISTEC entwickeln der Fachbereich 7.2 „Ingenieurbau“ innovative Monitoringverfahren zur Systemidentifikation und automatischen Detektion, Lokalisierung und Quantifizierung von Schäden an Infrastrukturbauwerken anhand von gemessenen dynamischen und statischen Bauwerksdaten. Im Rahmen dieses Projektes werden die Verfahren an der Maintalbrücke bei Gemünden angewendet, welche Teil der ICE-Strecke Hannover-Würzburg ist. In diesem Vortrag wird das für die Maintalbrücke Gemünden geplante und umgesetzte Monitoingsystem vorgestellt.
Identifying optimal inspection and repair strategies for offshore jacket structures is a challenging task. We pre-sent an approach, which is based on recent developments in the field of risk-based operation and maintenance planning at the structural system level. The approach utilizes heuristics to define inspection and repair strate-gies at the system level and to reduce the search space of possible strategies. For each defined strategy, the expected service life cost of inspection, repair and failure is evaluated based on simulated inspection and re-pair histories. Subset simulation is applied to compute the conditional repair and failure probabilities required for this analysis. It also forms the basis for simulating inspection and repair histories. The strategy that mini-mizes the expected service life cost is the optimal one in the set of pre-selected strategies. The underlying condition and performance model accounts for the stochastic dependence among the deterioration states of the different structural elements and the structural redundancy. The approach is demonstrated in a case study considering a jacket-type frame. In this study, we essentially vary the inspection interval, the minimum num-ber of inspected components and the target reliability, and identify the combination that minimizes the ex-pected total service life cost.
The Bundesanstalt für Materialforschung und -prüfung (BAM) collaborates with TNO to develop a software framework for automated calibration of structural models based on monitoring data. The ultimate goal is to include such models in the asset management process of engineering structures. As a basis for developing the framework, a multi-span road bridge consisting of ten simply supported steel box girders was selected as a test case. Our group measured output-only vibration data from one box girder under ambient conditions. From the data, we determined eigenfrequencies and mode shapes. In parallel, we developed a preliminary structural model of the box girder for the purpose of predicting its modal properties. In this contribution, we provide an overview of the measurement campaign, the operational modal analysis, the structural modeling and qualitatively compare the identified with the predicted modes. As an outlook, we discuss the further steps in the calibration process and future applications of the calibrated model.
The reliability of deteriorating structures at time t is quantified by the probability that failure occurs within the period leading up to time t. This probability is often referred to as cumulative failure probability and is equal to the cumulative distribution function of the time to failure. In structural reliability, an estimate of the cumulative failure probability is obtained based on probabilistic Engineering models of the deterioration processes and structural performance. Information on the condition and the loading contained in inspection and monitoring data can be included in the probability estimate through Bayesian updating. Conditioning the
probability of failure on the inspection or monitoring outcomes available at time t (e.g. detections or no detection of damages) can lead to a reduction in that probability.
Such a drop in the cumulative failure probability might seem counterintuitive since the cumulative failure probability is a non-decreasing function of time. In this paper, we illustrate—with the help of a numerical example—that such a drop is possible because the cumulative probability before and after the updating is not based on the same information, hence not on the same probabilistic model.
Bei Monopfahlgründungen von Offshore-Windenergieanlagen wird die Verbindung zwischen Monopfahl und Übergangsstück als geschraubter Ringflansch ausgeführt. Die zunehmende Leistungsfähigkeit der Windenergieanlagen führt zu immer größeren Schnittgrößen in diesem Anschluss. In der Folge erhöhen sich nicht nur die Querschnittsabmessungen, sondern es kommen auch zunehmend größere Schrauben zum Einsatz. Da die einschlägigen Regelwerke zur Bemessung dieser Verbindungen nicht für Schrauben der Größen M64 oder M72 konzipiert wurden, stellt sich die Frage der Übertragbarkeit auf solche Anwendungsfälle.
Im Rahmen des Aufsatzes werden Einflüsse diskutiert, die eine Herabsetzung der Schraubentragfähigkeit verursachen könnten. Diese Einflüsse, vornehmlich geometrische Imperfektionen, werden systematisch untersucht und ergänzend in praxisrelevanten Beispielen bewertet. Die somit gewonnenen Erkenntnisse werden für die abschließende Beurteilung der großen Schrauben in Ringflanschverbindungen herangezogen.
Grouting is a universal repair and strengthening technique, which is constantly used for structural remediation of concrete components, trenches, mine subsidence, dam joints, restoration of masonry structures, and geological stabilizations. Having an extremely small particle size of only few microns, ultrafine cements are ideal for grouting applications due to their superior permeability and compressive strength properties of the hardened cement paste compared to that of the less-expensive, but coarser ordinary Portland cements. Supplementary cementitious materials (SCMs) are often used to replace ultrafine cement in order to modify certain properties and to reduce costs. The aim of this experimental study is to investigate the effect of three supplementary materials: microsilica (MS), fly ash (FA), and metakaolin (MK) on the workability, and mechanical properties of an ultrafine cement based grout with a constant water-binder ratio and constant superplasticizer content. Maximum percentages of replacement with ultrafine cement were 6% by volume of cement for MS and 16% for FA, and MK. In general, results suggest that the workability is improved by addition of FA, whereas is reduced, when modified with MS and MK. The compressive strength of grout after cement replacement remains comparable to that of pure cement grout. However, there is a tendency of the MS to positively affect the compressive strength opposite to FA, whereas flexural strength is positively affected by FA. Based on the results, it is evident that grouts with Hägerman cone flow more than 500 mm and compressive strength of more than 90 MPa after 28 days can be produced.
Remediation of Cracks Formed in Grouted Connections of Offshore Energy Structures under Static Loads
(2018)
The future energy demand necessitates the exploration of all potential energy sources both onshore and offshore. Global trend has shifted towards offshore energy, which can be obtained from either carbon intensive or renewable options, hence requiring structures such as rigs, platforms, and monopiles. Most of these structures adopt easily installable construction techniques, where lower foundation need to be connected with the super structure by mean of grouted composite joints. Generally, these composite connections have exterior sleeve, interior pile and infill grout. Being located in remote offshore conditions, connections can experience considerable adverse loading during their lifetimes. Degradations were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites may often be proven difficult, which eventually leads to reduced capacity of connections in the long run. Thus, repair and rehabilitation of such connections should be planned ahead to minimize operational delays and costs in the future. This study aims at characterizing the nature of crack generation in grouted connections and thereby identifying the potential of repair using suitable repair material. Scaled grouted joints were manufactured using a novel mold, and connections were loaded under static load to visualize the main failure pattern. The failure mechanism and loading capacity are found compatible to previous results from earlier literature. Grouted connection was then repaired using cementitious injectable grout. The effectiveness of the repair system is also discussed.
Superplasticizer and shrinkage reducing admixture dosages for microfine cement in grout systems
(2018)
Grouts have numerous applications including crack repair as maintenance in construction industries. Microfine cements are intensively used for high strength mortar and grout products. They are ideal for injection grouting in structural repair. Such grouts should have suitable rheological properties to be injectable, especially those used in repair and rehabilitation. The use of superplasticizers (SP) in these products is thus becoming increasingly crucial to achieve favorable workability and viscosity properties. A difficulty in such grouts is the plastic shrinkage due to finer particles used. It is thus necessary to determine optimum SP and shrinkage reducing admixture (SRA) dosages for a microfine cement based grout. In this study, a saturation dosage was decided from two Polycarboxylate ether (PCE) based SPs in relation to neat cement using slump flow and rheological parameters. A range of grout mixtures was formulated containing micro silica (MS) and fly ash (FA), and tested for suitable rheological and mechanical parameters. Based on the results, a grout mixture with MS and FA was selected to determine optimum SRA content. According to the results, a SP dosage of 3% by weight of neat cement is sufficient to achieve saturation. The grout material including MS and FA can produce comparable properties to neat cement grout. MS is found to improve compressive strength within the range considered, whereas a higher FA content provides favourable rheological properties. Finally, a SRA dosage of 4%, which could reduce the shrinkage by about 43% after 28d days, is determined for the grout system.
Grouting is a universal repair and strengthening technique, which is constantly used for structural remediation of concrete components, trenches, mine subsidence, dam joints, restoration of masonry structures, and geological stabilizations. Having an extremely small particle size of only few microns, ultrafine cements are ideal for grouting applications due to their superior permeability and compressive strength properties of the hardened cement paste compared to that of the less-expensive, but coarser ordinary Portland cements. Supplementary cementitious materials (SCMs) are often used to replace ultrafine cement in order to modify certain properties and to reduce costs. The aim of this experimental study is to investigate the effect of three supplementary materials: microsilica (MS), fly ash (FA), and metakaolin (MK) on the workability, and mechanical properties of an ultrafine cement based grout with a constant water-binder ratio and constant superplasticizer content. Maximum percentages of replacement with ultrafine cement were 6% by volume of cement for MS and 16% for FA, and MK. In general, results suggest that the workability is improved by addition of FA, whereas is reduced, when modified with MS and MK. The compressive strength of grout after cement replacement remains comparable to that of pure cement grout. However, there is a tendency of the MS to positively affect the compressive strength opposite to FA, whereas flexural strength is positively affected by FA. Based on the results, it is evident that grouts with Hägerman cone flow more than 500 mm and compressive strength of more than 90 MPa after 28 days can be produced.
Grouts have numerous applications in construction industry such as joint sealing, structural repair, and connections in precast elements. They are particularly favoured in rehabilitation of structures due to penetrability and convenience of application. Grouts for repair applications typically require high-performance properties such as rapid strength development and superior shrinkage characteristics. Sometimes industrial by-products referred as supplementary cementitious materials (SCM) are used with neat cement due to their capabilities to provide binding properties at delayed stage. Micro silica, fly ash and metakaolin are such SCMs, those can modify and improve properties of cement products. This study aims at investigating long-term mass loss and linear shrinkage along with long-term compressive and flexural strength for grouts produced from ultrafine cement and SCMs. A series of mixtures were formulated to observe the effect of SCMs on these grout properties. Properties were determined after 365 days of curing at 23oC and 55% relative humidity. The effect of SCMs on the properties are characterised by statistical models. Response surfaces were constructed to quantify these properties in relation to SCMs replacement. The results suggested that shrinkage was reduced by metakaolin, while micro silica and fly ash had positive effects on compressive and flexural strength, respectively.
Superplasticizer and Shrinkage Reducing Admixture Dosages for Microfine Cement in Grout Systems
(2019)
Grouts have numerous applications including crack repair as maintenance in construction industries. Microfine cements are intensively used for high strength mortar and grout products. They are ideal for injection grouting in structural repair. Such grouts should have suitable rheological properties to be injectable, especially those used in repair and rehabilitation. The use of superplasticizers (SP) in these products is thus becoming increasingly crucial to achieve favorable workability and viscosity properties. A difficulty in such grouts is the plastic shrinkage due to finer particles used. It is thus necessary to determine optimum SP and shrinkage reducing admixture (SRA) dosages for a microfine cement based grout. In this study, a saturation dosage was decided from two Polycarboxylate ether (PCE) based SPs in relation to neat cement using slump flow and rheological parameters. A range of grout mixtures was formulated containing micro silica (MS) and fly ash (FA), and tested for suitable rheological and mechanical parameters. Based on the results, a grout mixture with MS and FA was selected to determine optimum SRA content. According to the results, a SP dosage of 3% by weight of neat cement is sufficient to achieve saturation. The grout material including MS and FA can produce comparable properties to neat cement grout. MS is found to improve compressive strength within the range considered, whereas a higher FA content provides favourable rheological properties. Finally, a SRA dosage of 4%, which could reduce the shrinkage by about 43% after 28d days, is determined for the grout system.
Repair is an indispensable part of the maintenance of structures over their lifetimes. Structural grouting is a widely used remediation technique for concrete components, trenches, mine subsidence, dam joints, restoration of masonry structures, and geological stabilizations. A structural grout system should be injectable in narrow spaces and hence include ingredients with finer particles. Ultrafine cements are ideal for these type of demanding grouts due to their superior properties compared to that of the less expensive, but coarser ordinary Portland cement (OPC). Supplementary cementitious materials (SCMs) are often used to replace OPC clinker based binder in order to modify certain properties and to reduce costs. The most commonly used SCMs are fly ash (FA), and ground granulated blast furnace slag (GGBS). For various special applications microsilica (MS), and metakaolin (MK) are also used. Identifying the optimum replacement contents of OPC by SCMs are a challenge during the design of such grouts. The aim of this experimental study is to investigate the effect of the selected SCMs (FA, MS and MK) on the slump flow, time of efflux, viscosity, shrinkage, and compressive and flexural strength of ultrafine cement based grouts with constant water-binder ratio and superplasticizer content. The test program was formulated using Box-Behnken design principles. Maximum percentages of replacement with ultrafine cement was 6% by volume of cement for MS and 16% for FA, and MK. The results suggest that most investigated grouts have the potential to be used for structural applications. The appropriate quadratic models are then formulated through statistical tools and presented as response surfaces. The trends indicate that fly ash improves the rheological properties, whereas microsilica and metakaolin positively affect shrinkage and mechanical properties to some extent. Based on the influence of SCMs and priorities among the properties, Decision Matrix Analysis (DMA) is carried out to select the most suitable ones among the SCMs. The analysis suggests that microsilica and fly ash are more suitable as SCMs than metakaolin without affecting the properties.
Remediation of Cracks Formed in Grouted Connections of Offshore Energy Structures under Static Loads
(2018)
The future energy demand necessitates the exploration of all potential energy sources both onshore and offshore. Global trend has shifted towards offshore energy, which can be obtained from either carbon intensive or renewable options, hence requiring structures such as rigs, platforms, and monopiles. Most of these structures adopt easily installable construction techniques, where lower foundation need to be connected with the super structure by mean of grouted composite joints. Generally, these composite connections have exterior sleeve, interior pile and infill grout. Being located in remote offshore conditions, connections can experience considerable adverse loading during their lifetimes. Degradations were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites may often be proven difficult, which eventually leads to reduced capacity of connections in the long run. Thus, repair and rehabilitation of such connections should be planned ahead to minimize operational delays and costs in the future. This study aims at characterizing the nature of crack generation in grouted connections and thereby identifying the potential of repair using suitable repair material. Scaled grouted joints were manufactured using a novel mold, and connections were loaded under static load to visualize the main failure pattern. The failure mechanism and loading capacity are found compatible to previous results from earlier literature. Grouted connection was then repaired using cementitious injectable grout. The effectiveness of the repair system is also discussed.
Impact resistance of reinforced concrete (RC) structures can be significantly improved by strengthening RC members with thin composite layers featuring high damage tolerance. Indeed, to limit the well-known vulnerability of cement-based materials against impact loading, the synergistic effects of short fibres and continuous textile meshes as hybrid reinforcement has been proved to be highly beneficial. This paper addresses the characterisation of novel cement-based hybrid composites through accelerated drop-weight impact tests conducted on rectangular plates at different impact energies. Two distinct matrices are assessed, with particular interest in a newly developed limestone calcined clay cement (LC3)-based formulation. Important parameters quantifying energy dissipation capability, load bearing capacity and damage are cross-checked to compute the ballistic limit and estimate the safety-relevant characteristics of the different composites at hand. Although textiles alone can improve the damage tolerance of fine concrete to some extent, the crack-bridging attitude of short, well-dispersed fibres in hybrid composites imparts a certain ductility to the cement-based matrices, allowing a greater portion of the textile to be activated and significantly reducing the amount of matrix spalling under impact.
Brücken sind Teil der alternden Verkehrsinfrastruktur. Um die Nutzungsdauer zu verlängern und plötzliche Schäden zu detektieren kann Bauwerksmonitoring ("Structural Health Monitoring") eingesetzt werden. Der Einfluss von Umgebungsbedingungen, beispielsweise der Temperatur, auf das Bauwerksverhalten ist meist größer als der Einfluss von Schäden. Diese Einflüsse bestmöglich voneinander zu trennen und Veränderungen im Tragverhalten korrekt Schäden oder Umgebungsbedingungen zuzuordnen ist eine offene Forschungsfrage. Diese Arbeit zeigt eine mögliche Lösung, bei der gekoppelte Modelle von Umwelteinflüssen, Schäden und Tragverhalten des Bauwerks auf Grundlage von Monitoringdaten aktualisiert werden. Das Framework dazu wird vorgestellt und an einem Laborexperiment eines Stahlbetonbalkens in der Klimakammer angewandt. Die Ergebnisse bestätigen die Vorgehensweise. In nächsten Schritten müssen komplexere Tragwerke und die Sensitivität des Ansatzes untersucht werden.
Changes in the measured response of structural systems can be an indication of structural damages. However, such changes can also be caused by the effect of varying environmental conditions. To detect, localize and quantify changes or damages in structural systems subject to varying environmental conditions, physics-based models of the structural systems have to be applied which explicitly account for the influence of ambient conditions on the structural behavior. Data obtained from the structural systems should be used to calibrate the models and update predictions. Bayesian system identification is an effective framework for this task. In this paper, we apply this framework to learn the parameters of two competing structural models of a reinforced concrete beam subject to varying temperatures based on static response data. The models describe the behavior of the beam in the uncracked and cracked condition. The data is collected in a series of load tests in a climate chamber. Bayesian model class selection is then applied to infer the most plausible condition of the beam conditional on the available data.
Inspection and maintenance contribute significantly to the lifetime cost of bridges. There is significant potential in using information obtained through structural health monitoring to update predictive models of the condition and performance of such structures, and thus ena-ble an improved decision-making regarding inspection and maintenance activities. Within the AISTEC project funded by the German Federal Ministry of Education and Research, we develop vibration-based structural health monitoring systems aimed at continuously provid-ing information on the structural condition of bridges. Environmental variations such as changing ambient temperatures can significantly influence the dynamic characteristics of bridges and thus mask the effect of structural changes and damages. It remains a challenge to account for such influences in structural health monitoring. To study the effect of ambient temperatures on the dynamic characteristics of beam structures, we monitor the vibration response of a reinforced concrete beam in the uncracked and cracked state at varying tem-peratures in a climate chamber. We postulate a set of competing parameterized probabilistic structural models, which explicitly account for the effect of varying ambient temperatures on the mechanical properties of the system. We then combine the information provided by the structural models with the information contained in the recorded vibration data to learn the parameters of the temperature-dependent structural models and infer the plausible state of the beam using Bayesian system identification and model class selection.
Die aktuelle Instandhaltungsstrategien von Ingenieurbauwerken arbeiten zustandsbasiert und stützen sich auf visuelle Inspektionen in kurzen, starren Intervallen. Beim Übergang zu Predicitive-Maintenance-Strategien können Sensordaten eigesetzt werden um Prognosemodelle der Bauwerke zu aktualisieren. Ein erster Schritt hierzu ist die sensorbasierte Systemidentifikation.
Kontinuierliche Sensorbasierte Bauwerksmessungen leisten einen wichtigen Beitrag zur Sicherheit von Verkehrsbauwerken. Hierzu werden im Vorhaben AISTEC Referenzbauwerke und Referenzverfahren untersucht mit Schwerpunkt auf den Einfluss klimatischer Bedingungen. Der Vortrag stellt den aktuellen Projektstand des FB 7.2 vor.
Structural health monitoring (SHM) intends to improve the management of engineering structures. The number of successful SHM projects – especially SHM research projects – is ever growing, yielding added value and more scientific insight into the management of infrastructure asset. With the advent of the data age, the value of accessible data becomes increasingly evident. In SHM, many new data-centric methods are currently being developed at a high pace. A consequent application of research data management (RDM) concepts in SHM projects enables a systematic management of raw and processed data, and thus facilitates the development and application of artificial intelligence (AI) and machine learning (ML) methods to the SHM data. In this contribution, a case study based on an institutional RDM framework is presented. Data and metadata from monitoring the structural health of the Maintalbrücke Gemünden for a period of 16 months are managed with the RDM system BAM Data Store, which makes use of the openBIS data management software. An ML procedure is used to classify the data. Feature engineering, feature training and resulting data
are performed and modelled in the RDM system.
Gradual or sudden changes in the state of structural systems caused, for example, by deterioration or accidental load
events can influence their load-bearing capacity. Structural changes can be inferred from static and/or dynamic response data
measured by structural health monitoring systems. However, they may be masked by variations in the structural response due to
varying environmental conditions. Particularly, the interaction of nominally load-bearing components with nominally non-load
bearing components exhibiting characteristics that vary as a function of the environmental conditions can significantly affect the
monitored structural response. Ignoring these effects may hamper an inference of structural changes from the monitoring data. To
address this issue, we adopt a probabilistic model-based framework as a basis for developing digital twins of structural systems
that enable a prediction of the structural behavior under varying ambient condition. Within this framework, different types of data
obtained from real the structural system can be applied to update the digital twin of the structural system using Bayesian methods
and thus enhance predictions of the structural behavior. In this contribution, we implement the framework to develop a digital
twin of a simply supported steel beam with an asphalt layer. It is formulated such that it can predict the static response of the beam
in function of its temperature. In a climate chamber, the beam was subject to varying temperatures and its static response wass
monitored. In addition, tests are performed to determine the temperature-dependent properties of the asphalt material. Bayesian
system identification is applied to enhance the predictive capabilities of the digital twin based on the observed data.
Die Infrastruktursysteme der Industriestaaten erfordern heute und in Zukunft ein effizientes Management bei alternder Bausubstanz, steigenden Lasten und gleichbleibend hohem Sicherheitsniveau. Digitale Technologien bieten ein großes Potenzial zur Bewältigung der aktuellen und künftigen Herausforderungen im Infrastrukturmanagement. Im BMBF-geförderten Projekt Bewertung alternder Infrastrukturbauwerke mit digitalen Technologien (AISTEC) wird untersucht, wie unterschiedliche Technologien und deren Verknüpfung gewinnbringend eingesetzt werden können. Am Beispiel der Maintalbrücke Gemünden werden ein sensorbasiertes Bauwerksmonitoring, bildbasierte Inspektion mit durch Kameras ausgestatteten Drohnen (UAS) und die Verknüpfung digitaler Bauwerksmodelle umgesetzt. Die aufgenommenen Bilder dienen u. a. als Grundlage für spätere visuelle Anomaliedetektionen und eine 3D-Rekonstruktion, welche wiederum für die Kalibrierung und Aktualisierung digitaler Tragwerksmodelle genutzt werden. Kontinuierlich erfasste Sensordaten werden ebenfalls zur Kalibrierung und Aktualisierung der Tragwerksmodelle herangezogen. Diese Modelle werden als Grundlage für Anomaliedetektionen und perspektivisch zur Umsetzung von Konzepten der prädiktiven Instandhaltung verwendet. Belastungsfahrten und historische Daten dienen in diesem Beitrag der Validierung von kalibrierten Tragwerksmodellen.
Structural health monitoring (SHM) intends to improve the management of engineering structures. The number of successful SHM projects – especially SHM research projects – is ever growing, yielding added value and more scientific insight into the management of infrastructure asset. With the advent of the data age, the value of accessible data becomes increasingly evident. In SHM, many new data-centric methods are currently being developed at a high pace. A consequent application of research data management (RDM) concepts in SHM projects enables a systematic management of raw and processed data, and thus facilitates the development and application of artificial intelligence (AI) and machine learning (ML) methods to the SHM data. In this contribution, a case study based on an institutional RDM framework is presented. Data and metadata from monitoring the structural health of the Maintalbrücke Gemünden for a period of 16 months are managed with the RDM system BAM Data Store, which makes use of the openBIS data management software. An ML procedure is used to classify the data. Feature engineering, feature training and resulting data are performed and modelled in the RDM system.
Changes in the measured response of structural systems can be an indication of structural damages. However, such changes can also be caused by the effect of varying environmental conditions. To detect, localize and quantify changes or damages in structural systems subject to varying environmental conditions, physics-based models of the structural systems have to be applied which explicitly account for the influence of ambient conditions on the structural behavior. Data obtained from the structural systems should be used to calibrate the models and update predictions. Bayesian system identification is an effective framework for this task. In this paper, we apply this framework to learn the parameters of two competing structural models of a reinforced concrete beam subject to varying temperatures based on static response data. The models describe the behavior of the beam in the uncracked and cracked condition. The data is collected in a series of load tests in a climate chamber. Bayesian model class selection is then applied to infer the most plausible condition of the beam conditional on the available data.
Managing aging engineering structures requires damage identification, capacity reassessment, and prediction of remaining service life. Data from structural health monitoring (SHM) systems can be utilized to detect and characterize potential damage. However, environmental and operational variations impair the identification of damages from SHM data. Motivated by this, we introduce a Bayesian probabilistic framework for building models and identifying damage in monitored structures subject to environmental variability. The novelty of our work lies (a) in explicitly considering the effect of environmental influences and potential structural damages in the modeling to enable more accurate damage identification and (b) in proposing a methodological workflow for model‐based structural health monitoring that leverages model class selection for model building and damage identification. The framework is applied to a progressively damaged reinforced concrete beam subject to temperature variations in a climate chamber. Based on deflections and inclinations measured during diagnostic load tests of the undamaged structure, the most appropriate modeling approach for describing the temperature‐dependent behavior of the undamaged beam is identified. In the damaged state, damage is characterized based on the identified model parameters. The location and extent of the identified damage are consistent with the cracks observed in the laboratory. A numerical study with synthetic data is used to validate the parameter identification. The known true parameters lie within the 90% highest density intervals of the posterior distributions of the model parameters, suggesting that this approach is reliable for parameter identification. Our results indicate that the proposed framework can answer the question of damage identification under environmental variations. These findings show a way forward in integrating SHM data into the management of infrastructures.
Gradual or sudden changes in the state of structural systems caused, for example, by deterioration or accidental load events can influence their load-bearing capacity. Structural changes can be inferred from static and/or dynamic response data measured by structural health monitoring systems. However, they may be masked by variations in the structural response due to varying environmental conditions. Particularly, the interaction of nominally load-bearing components with nominally non-load bearing components exhibiting characteristics that vary as a function of the environmental conditions can significantly affect the monitored structural response. Ignoring these effects may hamper an inference of structural changes from the monitoring data. To address this issue, we adopt a probabilistic model-based framework as a basis for developing digital twins of structural systems that enable a prediction of the structural behavior under varying ambient condition. Within this framework, different types of data obtained from real the structural system can be applied to update the digital twin of the structural system using Bayesian methods and thus enhance predictions of the structural behavior. In this contribution, we implement the framework to develop a digital twin of a simply supported steel beam with an asphalt layer. It is formulated such that it can predict the static response of the beam in function of its temperature. In a climate chamber, the beam was subject to varying temperatures and its static response wass monitored. In addition, tests are performed to determine the temperature-dependent properties of the asphalt material. Bayesian system identification is applied to enhance the predictive capabilities of the digital twin based on the observed data.
Inspection and maintenance contribute significantly to the lifetime cost of bridges. There is significant potential in using information obtained through structural health monitoring to update predictive models of the condition and performance of such structures, and thus ena-ble an improved decision-making regarding inspection and maintenance activities. Within the AISTEC project funded by the German Federal Ministry of Education and Research, we develop vibration-based structural health monitoring systems aimed at continuously provid-ing information on the structural condition of bridges. Environmental variations such as changing ambient temperatures can significantly influence the dynamic characteristics of bridges and thus mask the effect of structural changes and damages. It remains a challenge to account for such influences in structural health monitoring. To study the effect of ambient temperatures on the dynamic characteristics of beam structures, we monitor the vibration response of a reinforced concrete beam in the uncracked and cracked state at varying tem-peratures in a climate chamber. We postulate a set of competing parameterized probabilistic structural models, which explicitly account for the effect of varying ambient temperatures on the mechanical properties of the system. We then combine the information provided by the structural models with the information contained in the recorded vibration data to learn the parameters of the temperature-dependent structural models and infer the plausible state of the beam using Bayesian system identification and model class selection.
Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores ( 1 m), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption.
In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany.
The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %.
Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (less than1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption.
In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany.
The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. These effects are prominent in the meso-pore range and might significantly alter the effective diffusion coefficient.
Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (< 1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption.
In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany.
The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %.
Reliability analysis of deteriorating structural systems requires the solution of time-variant reliability problems.
In the general case, both the capacity of and the loads on the structure vary with time. This analysis can be approached by approximation through a series of time-invariant reliability problems, which is a potentially effective strategy for cases where direct solutions of the time-variant reliability problem are challenging, e.g. for structural systems with many elements or arbitrary load processes. In this contribution, we thoroughly Review the formulation of the equivalent time-invariant reliability problems and extend this approximation to structures for which inspection and monitoring data is available. Thereafter, we present methods for efficiently evaluating the reliability over time. In particular, we propose the combination of sampling-based methods with a FORM (first-order reliability method) approximation of the series system reliability problem that arises in the computation of the lifetime reliability. The framework and algorithms are demonstrated on a set of numerical examples, which include the computation of the reliability conditional on inspection data.
Automated modal analysis for tracking structural change during construction and operation phases
(2019)
The automated modal analysis (AMA) technique has attracted significant interest over the last few years, because it can track variations in modal parameters and has the potential to detect structural changes. In this paper, an improved density-based spatial clustering of applications with noise (DBSCAN) is introduced to clean the abnormal poles in a stabilization diagram. Moreover, the optimal system model order is also discussed to obtain more stable poles. A numerical Simulation and a full-scale experiment of an arch bridge are carried out to validate the effectiveness of the proposed algorithm. Subsequently, the continuous dynamic monitoring system of the bridge and the proposed algorithm are implemented to track the structural changes during the construction phase. Finally, the artificial neural network (ANN) is used to remove the temperature effect on modal frequencies so that a health index can be constructed under operational conditions.
For the generation of renewable energy offshore wind farms play an important role. The majority of these wind generators are connected to steel foundation structures. Steady increasing power output of these wind turbines leads to new challenges as well for engineers of the related support structures. Caused by the high-cyclic loading of these structures by wind and waves fatigue plays a very important role. Besides the consideration of fatigue within the design process it is additionally an important topic and challenge to monitor the existing steel structures relating to potential fatigue cracks occurring during their lifetime. This plays a role for a fundamental understanding of mechanisms as investigated in testing but also for inspection in real structures.
Since the structures of the offshore wind generators are very large and in addition partially under water effective and reliable methods for fatigue crack detection are required. This contribution will present results of recent investigations on different crack detection methods applied on high-cycle fatigue tests on small welded steel samples as well as on welded steel components. The comparison of these measurements will show what are the advantages and disadvantages of the different methods and which method is potentially more suitable for the application on real offshore wind structures. It is outlined where challenges for detection methods exist.
Furthermore, in this context the resulting challenges for the execution of material testing especially caused by the increasing dimensions of wind energy converters will by exemplarily presented.
At present, to produce renewable energy offshore wind farms play an important role. The available space combined with the more valuable wind conditions make offshore locations very attractive for wind powered energy production. In Europe a significant number of offshore wind farms already exist, especially in the North and Baltic Sea. In future this trend will continue, and further offshore wind farms will be built. The majority of offshore wind turbines are mounted on steel foundation structures. Due to the high-cyclic loading by wind and waves fatigue stress plays a substantial role regarding structural safety.
Besides the consideration of fatigue within the design process, to monitor existing steel structures for potential fatigue cracks during their life time is a major topic and a challenge.
For the structures of the offshore wind turbines are large and partially under water effective reliable methods for the detection of fatigue cracks are required.
This contribution presents investigations on different crack detection methods applied at high-cycle fatigue tests on small-scale welded steel samples as well as on large-scale welded steel components. The tests were conducted at the BAM laboratories. For crack detection mainly three different methods were used and compared. The first method regards to the measurement of strain by conventionally strain gauges. Secondly, the crack luminescence was used as a new and effective optical method for surface monitoring. And finally, crack detection by pressure differentials of the inner and outer section of tubular steel elements was investigated. A comparison study will emphasize the advantages and disadvantages of the different methods and show which of the described methods is potentially more suitable for an application on real offshore wind structures.
Fatigue in Concrete
(2019)
The current knowledge about fatigue behavior of concrete is still incomplete. This concerns especially the progress of fatigue which precedes the fatigue failure. An overview on the fatigue behaviour in concrete is given. Therefore, the process of fatigue itself under cyclic compressive loading was investigated in a systematic and comprehensive way. The aim of this investigation was to obtain a deeper insight and to provide a better understanding of the damage process occurring within the material during fatigue loading.
At present, to produce renewable energy offshore wind farms play an important role. The available space combined with the more valuable wind conditions make offshore locations very attractive for wind powered energy production. In Europe a significant number of offshore wind farms already exist, especially in the North and Baltic Sea. In future this trend will continue, and further offshore wind farms will be built. The majority of offshore wind turbines are mounted on steel foundation structures. Due to the high-cyclic loading by wind and waves fatigue stress plays a substantial role regarding structural safety.
Besides the consideration of fatigue within the design process, to monitor existing steel structures for potential fatigue cracks during their life time is a major topic and a challenge.
For the structures of the offshore wind turbines are large and partially under water effective reliable methods for the detection of fatigue cracks are required.
This contribution presents investigations on different crack detection methods applied at high-cycle fatigue tests on small-scale welded steel samples as well as on large-scale welded steel components. The tests were conducted at the BAM laboratories. For crack detection mainly three different methods were used and compared. The first method regards to the measurement of strain by conventionally strain gauges. Secondly, the crack luminescence was used as a new and effective optical method for surface monitoring. And finally, crack detection by pressure differentials of the inner and outer section of tubular steel elements was investigated. A comparison study will emphasize the advantages and disadvantages of the different methods and show which of the described methods is potentially more suitable for an application on real offshore wind structures.
Reinforced concrete is a widely used material for power generation structures, where load scenarios like impact loadings need to be considered. In this context mechanical splicing systems for the connection of reinforcement bars are of specific interest and impact resistance for the splicing systems has to be verified. High speed tensile tests need to be performed on splicing systems for reinforcement bars to confirm the capability of the coupler to resist impact loading. Furthermore, the ability of the reinforcement steel to dissipate energy by ductile behaviour with pronounced plastic strains should be confirmed by these tests. During the last decades comprehensive experiences were developed at BAM performing high speed tensile tests on reinforcement bars as well as on several splicing systems. For the lack of available standards defining these tests in detail an appropriate test procedure was developed and continuously optimized during this period at BAM. The test procedure is partially based on testing principles adapted from available standards. The main intention behind this test procedure is to perform high-speed tensile tests with a specific constant strain rate generated at the specimen. Furthermore, main objective was to establish a procedure to guarantee the comparability of test results for different diameter of reinforcement as well as for different types of couplers. Besides the pure execution of the high-speed tensile tests, the test specification also declares how to evaluate the measurements and the test results. Finally, some typical results will be presented in this contribution.
This document presents the specification for the execution and evaluation of high-speed tensile tests on reinforcement bar coupler systems. This specification was developed at BAM - Bundesanstalt für Materialforschung und -prüfung (Federal Institute for Materials Research and Testing, Germany) - following test principles from related international standards.
The present document represents the latest status of the test specification. It is noted that until 2010 the test procedure was characterised on a test velocity based on L0. In an improved test conception and after intensive investigations in cooperation with industry partners, this procedure has been updated to consider instead a test velocity based on Lr, since this warrants more comparable and meaningful results.