7.2 Ingenieurbau
Filtern
Dokumenttyp
- Vortrag (169)
- Beitrag zu einem Tagungsband (82)
- Zeitschriftenartikel (63)
- Posterpräsentation (10)
- Buchkapitel (4)
- Dissertation (4)
- Beitrag zu einem Sammelband (3)
- Tagungsband (Herausgeberschaft für den kompletten Band) (1)
- Sonstiges (1)
Sprache
- Englisch (256)
- Deutsch (80)
- Mehrsprachig (1)
Schlagworte
- Structural Health Monitoring (25)
- Ground vibration (20)
- Fatigue (15)
- Structural health monitoring (15)
- Brücken (11)
- Monitoring (11)
- Offshore (11)
- Offshore wind energy (11)
- Hammer impact (9)
- Impact (9)
- Train passage (9)
- Damage characterization (8)
- Model interpolation (8)
- Planar tomography (8)
- Structural systems (8)
- Vibration measurements (8)
- Building vibration (7)
- Damage detection (7)
- Deterioration (7)
- Layered soil (7)
- Reliability (7)
- Slab track (7)
- Soil-structure interaction (7)
- Train-induced ground vibration (7)
- Bahnerschütterungen (6)
- Compressive strength (6)
- Design methods (6)
- Grout (6)
- Inspection (6)
- Numerical modelling (6)
- Offshore wind turbines (6)
- Physical phenomenology (6)
- Pile foundations (6)
- Reinforced concrete structure (6)
- SHM (6)
- Environmental effects (5)
- Interface (5)
- Layered soils (5)
- Modalanalyse (5)
- Numeric simulation (5)
- Repair (5)
- Temperature rejection (5)
- Ultrasonic testing (5)
- Vibration (5)
- Windenergie (5)
- Bayesian updating (4)
- Container loading (4)
- Crack detection (4)
- Damage localization (4)
- Datenmanagement (4)
- Drop test (4)
- Erosion (4)
- Erschütterungen (4)
- Erschütterungsminderung (4)
- Excitation forces (4)
- Fault detection (4)
- Foundation load (4)
- Foundations (4)
- Gründungsstrukturen (4)
- High-strength concrete (4)
- Inspection planning (4)
- Mitigation (4)
- Offshore geomechanics (4)
- Shell Buckling (4)
- Statistical tests (4)
- Steel structures (4)
- Subspace methods (4)
- Subspace-based method (4)
- Tunnel (4)
- Vehicle-track-soil interaction (4)
- Vibration measurement (4)
- Wind (4)
- Wind Energy (4)
- Ansys Autodyn (3)
- Attenuation (3)
- Axle impulses (3)
- BIM (3)
- Bauwerksüberwachung (3)
- Belastungsversuch (3)
- Box-Behnken (3)
- Bridge (3)
- Bridges (3)
- Buckling (3)
- Compaction Grouting (3)
- Cracks (3)
- DUCON® (3)
- Deep foundations (3)
- Dispersionsmessung (3)
- Drucker-Prager (3)
- Ductility (3)
- E-modulus (3)
- Earth masonry (3)
- Elastische Gleiselemente (3)
- Emission (3)
- Erschütterungsprognose (3)
- Filter effects (3)
- Fly ash (3)
- Grouted connection (3)
- Grouting (3)
- Großer Fallturm Horstwalde (3)
- Irregular soil (3)
- Leichtbau (3)
- Linear parameter varying systems (3)
- Load vector (3)
- Maintenance (3)
- Material moisture (3)
- Metakaolin (3)
- Micro-reinforcement (3)
- Micromechanical modelling (3)
- Mobile elements (3)
- Monopiles (3)
- Numerical modeling (3)
- Offshore Pile Foundation (3)
- Offshore Windenergieanlagen (3)
- Offshore foundations (3)
- Offshore wind turbine (3)
- Physical testing (3)
- Post-impact evaluation (3)
- Probabilistic (3)
- Quasi-static and dynamic tests (3)
- Railway (3)
- Railway bridge (3)
- Randomly heterogeneous soil (3)
- Rehabilitation (3)
- Reinforced concrete (3)
- Risk (3)
- Scattering (3)
- Schwingungsdynamik (3)
- Soil erosion (3)
- Soil properties (3)
- Statistical evaluation (3)
- Statistical method (3)
- Stereo photogrammetry (3)
- Subspace-based residual (3)
- Temperature effects (3)
- Train speed (3)
- UHPC (3)
- Vehicle-track interaction (3)
- Vibrations (3)
- Wellenausbreitung (3)
- Wellengeschwindigkeit (3)
- Zivile Sicherheit (3)
- 2-span bridge (2)
- AISTEC (2)
- Acceleration sensors (2)
- Achsfolgespektren (2)
- Acoustic emission testing (2)
- Amplitude-charge weight laws (2)
- Amplitude-distance laws (2)
- Analysis of variance (2)
- Apartment building (2)
- Artificial Intelligence (2)
- Artificial intelligence (2)
- Automatisierte schweißtechnische Fertigung (2)
- Axle sequence (2)
- Axle-sequence spectrum (2)
- Ballast track (2)
- Bauteile (2)
- Bauwerke (2)
- Bauwerksmonitoring (2)
- Bayes'sche Analyse (2)
- Bayesian System Identification (2)
- Bayesian analysis (2)
- Bayesian methods (2)
- Bayesian system identification (2)
- Bemessung (2)
- Big Data (2)
- Bitumen (2)
- Bodenübertragungsfunktion (2)
- Brücke (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Changing process noise (2)
- Chemisoprtion (2)
- Climate chamber (2)
- Compressive Cyclic loading (2)
- Compressive cyclic loading (2)
- Computer Vision (2)
- Concrete (2)
- Coupled fluid-particle simulation (2)
- Coupler systems (2)
- Crack Luminescence (2)
- Crack formation (2)
- Crack pattern (2)
- Cyclic load (2)
- DEM (2)
- Damage identification (2)
- Design (2)
- Digital twin (2)
- Digitalisierung (2)
- Displacements (2)
- Drone (2)
- Earth block masonry (2)
- Elastische Elemente (2)
- Elastische Gebäudelagerung (2)
- Energy (2)
- Erschütterungsausbreitung (2)
- Evaluation (2)
- Explosion-induced ground vibrations (2)
- Faseroptik (2)
- Feuchte (2)
- Finite Elemente Simulation (2)
- Finite element models (2)
- Freight train (2)
- GPU parallel computation (2)
- Gleiströge (2)
- Ground vibration measurements (2)
- Grouted Connection (2)
- Halbraum (2)
- High-performance computing (2)
- High-speed (2)
- High-speed train (2)
- Immission (2)
- Injection Sequence (2)
- Irregular ballast (2)
- Irregularities (2)
- Jacket support structure (2)
- Jet erosion test (2)
- Klimakammer (2)
- Knudsen effect (2)
- LBM-DEM (2)
- Laboratory beam structure (2)
- Lehm (2)
- Long-term shrinkage (2)
- Luminescence (2)
- Macromechanical Sample Strength (2)
- Material tests (2)
- Mauerwerk (2)
- Measurement (2)
- Measurements (2)
- Messen im Bauwesen (2)
- Micro silica (2)
- Micromechanical Tensile Failure (2)
- Mix design (2)
- Modal Analysis (2)
- Model updating (2)
- Moisture (2)
- Moisture content (2)
- Molecular diffusion (2)
- Non destructive testing (2)
- Non-Destructive Evaluation (2)
- Non-destructive testing (2)
- Numerical model (2)
- Office tower (2)
- Offshore Wind (2)
- Offshore Wind Energy (2)
- Offshore Windenergy Pile Buckling (2)
- Offshore geotechnics (2)
- Offshore wind (2)
- Offshore-Windenergieanlagen (2)
- Optimal Sensor Placement (2)
- Passenger train (2)
- Physisorption (2)
- Pile Foundation (2)
- Pile Tip Buckling (2)
- Prediction (2)
- Prediction of explosion induced ground and building vibration (2)
- Probability of Detection (2)
- Prädiktive Instandhaltung (2)
- Radar (2)
- Railway tunnel (2)
- Railways (2)
- Rechenmodelle (2)
- Reinforcement (2)
- Relative humidity (2)
- Repowering (2)
- Research data management (2)
- Residual evaluation (2)
- Resonance (2)
- Risslumineszenz (2)
- SDDLV (2)
- Safety (2)
- Scattered axle impulses (2)
- Schadensdetektion (2)
- Schwingungsbasierte Verfahren (2)
- Size effect (2)
- Slenderness effect (2)
- Soil-Structure-Interaction (2)
- Soil-pile interaction (2)
- Soil-wall-floor model (2)
- Static axle loads (2)
- Static load (2)
- Strength (2)
- Strukturmonitoring (2)
- Suction bucket (2)
- Supplementary cementitious materials (2)
- Surface-tunnel reduction (2)
- System Identification (2)
- System identification (2)
- Tensile Capacity (2)
- Time-variant reliability (2)
- Tomographic damage evaluation (2)
- Track damage (2)
- Track-soil interaction (2)
- Train excitation (2)
- Transmission (2)
- Umwelteinflüsse (2)
- Uncertainty (2)
- Uncertainty in reference (2)
- Uncertainty quantification (2)
- Unterraummethoden (2)
- Value of Information (2)
- Vehicle–track interaction (2)
- Vollraum (2)
- Wellenausbreitung in der Tiefe (2)
- Wind Turbines (2)
- Wind energy (2)
- Wind turbine tower (2)
- Windenergieanlagen (2)
- Windenergy (2)
- Zuggeschwindigkeit (2)
- Zuverlässigkeit (2)
- 3D imaging (1)
- Achsimpulse (1)
- Acoustic emission (1)
- Acoustic emission analysis (1)
- Ambient excitation (1)
- Amplituden-Abstands-Gesetze (1)
- Analytical Design Methods (1)
- Asphalt (1)
- Assessment (1)
- Asymptotic local approach (1)
- Automated Modal Analysis for Tracking Structural Change during Construction and Operation Phases (1)
- Automated operational modal analysis (1)
- Automatic modal parameters identification (1)
- Automatisierte Fertigung (1)
- Automatisierte schweißtechniche Fertigung (1)
- Autonomous underwater vehicles (1)
- Axial load bearing (1)
- Axle loads (1)
- Axle pulses (1)
- BAM Windenergie Fügetechnik (1)
- Bahngleis (1)
- Base isolation (1)
- Baugrunddynamik (1)
- Bauwerk-Boden-Wechselwirkung (1)
- Bauwerksdiagnostik (1)
- Beanspruchungszustand (1)
- Belastungsfahrt (1)
- Belastungstest (1)
- Belastungszug (1)
- Benchmark (1)
- Beton (1)
- Betonautobahn (1)
- Betonautobahnen (1)
- Beulen (1)
- Bewertung (1)
- Bionik (1)
- Blast (1)
- Blast tests (1)
- Bodenschlitz (1)
- Bodenvariabilität (1)
- Boundary element (1)
- Boundary element method (1)
- Bridge monitoring (1)
- Bridge resonance (1)
- Bridge vibration (1)
- Bruchlastwechselzahlen (1)
- Brückensicherheit (1)
- Buckling piles circular shells (1)
- Buckling soil-structure-interaction offshore piles track (1)
- Building and Construction (1)
- Building information modelling (1)
- Building response (1)
- Bulging (1)
- CFD (1)
- Cancellation (1)
- Cars (1)
- Cement-based composites (1)
- Centerline solidification cracking (1)
- Chemisorption (1)
- Civil and Structural Engineering (1)
- Civil structures (1)
- Climate Chamber (1)
- Coating (1)
- Cohesive granular materials (1)
- Cohesive soils (1)
- Column/wall resonance (1)
- Combined finite-element boundary-element method (1)
- Compaction grouting (1)
- Compliance function (1)
- Components of excitation (1)
- Compression tests (1)
- Computational (1)
- Condensed Matter Physics (1)
- Conductor (1)
- Continuous soil (1)
- Continuously inhomogeneous geological media (1)
- Continuously inhomogeneous soils (1)
- Crack (1)
- Crack damage detection (1)
- Crack growth (1)
- Crack repair (1)
- Cyber security (1)
- Cyclic axial shearing (1)
- Cyclic degradation (1)
- DEM-LBM simulation (1)
- Damage Detection (1)
- Damage evolution (1)
- Decision matrix analysis (1)
- Deckeneigenfrequenzen (1)
- Deckenschwingungen (1)
- Design models (1)
- Design practice (1)
- Detection (1)
- DiMoWind RDS-PP Maintenance Digital Twin Offshore Wind Energy (1)
- Digital Image Correlation (1)
- Digital Image Correlation (DIC) (1)
- Digital Models (1)
- Digital Twin (1)
- Digitale Zwillinge (1)
- Discrete Element Method (1)
- Discrete element method (1)
- Drop Test (1)
- Drop Tests (1)
- Drop tower (1)
- Druckfestigkeit (1)
- Druckschwellenversuch (1)
- Dynamic axle loads (1)
- Dynamic excitation (1)
- Dynamic loads (1)
- Dynamic soil properties (1)
- Dynamische Bodenkennwerte (1)
- Dynamische Bodensteifigkeit (1)
- Dämpfung (1)
- EERA Joint Program (1)
- Earth (1)
- Earth blocks (1)
- Earth material (1)
- Earthen hydraulic constructions (1)
- Earthen hydraulic infrastructures (1)
- Einflusslinie (1)
- Einflusslinien (1)
- Einfügungsdämmung (1)
- End-of-life decision making (1)
- Entscheidungsfindung (1)
- Environmental (1)
- Environmental Effects (1)
- Environmental changes (1)
- Environmental influence (1)
- Erhaltungsmanagement (1)
- Ermüdung (1)
- Ermüdungsprüfung (1)
- Ermüdungsschäden (1)
- Ermüdungsverhalten (1)
- Erneuerbare Energien (1)
- Erosion of cohesive soils (1)
- Erschütterungen im Fernfeld (1)
- Estimation (1)
- FEM (1)
- FEM analysis (1)
- Fahrzeug-Fahrweg-Boden-Wechselwirkung (1)
- Fallturm (1)
- Fatigue damage (1)
- Fatigue deterioration (1)
- Fatigue strength (1)
- Fault detectionchanging (1)
- Features (1)
- Fequency domain (1)
- Fiber optic sensing (1)
- Fibre optic sensors (1)
- Finite element (1)
- Finite element analysis (1)
- Finite element method (1)
- Finite element model updating (1)
- Finite elements (1)
- Finite-Elemente-Modellkalibrierung (1)
- Finite-element boundary-element method (1)
- Flexibility (1)
- Flexible car body (1)
- Flexible wheelset (1)
- Floor resonance (1)
- Floors (1)
- Fluid-structure interaction (1)
- Footbridge (1)
- Force reconstruction (1)
- Foundation Pile (1)
- Foundation reliability analysis (1)
- Freileitung (1)
- Frequency response function (1)
- GMNIA (1)
- GNSS (1)
- GPA (1)
- GPU Parallel computing (1)
- GPU parallelisation (1)
- Gebäudelagerung (1)
- Gebäudemodelle (1)
- Gebäudeschwingungen (1)
- General Materials Science (1)
- Geology (1)
- Geomechanics (1)
- Geomechanics of offshore foundations (1)
- Geometric vehicle and track irregularities (1)
- Geometrie (1)
- Global ambient vibrations (1)
- Granular Cohesive Materials (1)
- Granular Cohesive Materials, (1)
- Granular cohesion (1)
- Ground (1)
- Grout Injection (1)
- HAZID (1)
- HTLS (1)
- Hard impact (1)
- Harter Anprall an Stahlbetonstrukturen (1)
- High-Rise Building (1)
- High-rise building (1)
- High-rise buildings (1)
- Horizontal stress (1)
- Horizontal wind turbine (1)
- Hydraulic jet erosion (1)
- IEPE (1)
- Impact damage of reinforced concrete (1)
- Impact damage on reinforced concrete (1)
- Impact loading (1)
- Impakt (1)
- Impedanzmethode (1)
- Imperfektion (1)
- Impinging jet (1)
- Inclination angle (1)
- Inertial Interaction (1)
- Inertial interaction (1)
- Inhomogeneous soils (1)
- Innovative Messtechnik (1)
- Inspeciton (1)
- Inspektion (1)
- Interface model (1)
- Jet impingement (1)
- Kinematic Interaction (1)
- Kinematic interaction (1)
- Kraft auf den Boden (1)
- LBM-DEM coupling (1)
- LBM-DEM simulation (1)
- Laminar flow (1)
- Laminography (1)
- Large components (1)
- Laser beam welding (1)
- Lateral dynamic displacement (1)
- Lateral load bearing (1)
- Lattice Boltzmann Method (1)
- Lattice Boltzmann method (1)
- Leichtbauprinzipien (1)
- Lifetime Extension (1)
- Load Test (1)
- Load bearing behaviour (1)
- Load identification (1)
- Load tests (1)
- Load-bearing (1)
- Load-bearing behaviour (1)
- Local approaches (1)
- Long-span bridge (1)
- Low-frequency shaker (1)
- MEMS (1)
- Maintal Bridge Gemuenden (1)
- Maintalbrücke Gemünden (1)
- Maintenance Digital Twin Offshore Wind Energy (1)
- Marine geomechanics (1)
- Marine geotechnics (1)
- Maschinenbetrieb (1)
- Maschinenfundament (1)
- Material Point Method (1)
- Material Point Method (MPM) (1)
- Material model (1)
- Measurement campaigns (1)
- Mechanical challenges (1)
- Merkblatt (1)
- Messfahrt (1)
- Microfine Cement (1)
- Microfine cement (1)
- Micromechanical LBM-DEM simulation (1)
- Micromechanical analysis (1)
- Micromechanical simulation (1)
- Microsilica (1)
- Minderungsmaßnahmen (1)
- Mixed formulation (1)
- Modal analysis (1)
- Modal force spectrum (1)
- Modal load spectrum (1)
- Modal system identification (1)
- Model Update (1)
- Model update (1)
- Modell-Update (1)
- Modellierung (1)
- Modes (1)
- Modes and waves (1)
- Modulus of elasticity (1)
- Monitoring-informed inspection and maintenance planning (1)
- Monopile (1)
- Monopile Buckling (1)
- Monopile installation risks (1)
- Movin load test (1)
- Multi-beam method (1)
- Multi-beam track model (1)
- Multiple impact (1)
- NDT (1)
- Nachgiebigkeiten (1)
- Nelson’s method (1)
- Normung (1)
- Numerical analysis (1)
- Numerical damage simulation (1)
- Numerical simulation (1)
- Numerical simulation of impact damage (1)
- Numerical simulations (1)
- Numerische Analysen (1)
- Obstacles (1)
- Offhore (1)
- Office building (1)
- Offshore Structures (1)
- Offshore Wind Energy Converter (1)
- Offshore Windenergie (1)
- Offshore pile foundation (1)
- Offshore pile foundations (1)
- Offshore steel structures (1)
- Offshore wind energy foundations (1)
- Offshore wind farm (1)
- Offshore wind farms (1)
- Offshore wind-turbine foundations (1)
- Offshore-Wind (1)
- Operational modal analysis (1)
- Optimal sensor placement (1)
- Optimierungsmethoden (1)
- Optimization techniques (1)
- Perfectly Matched Layer (PML) (1)
- Pfahlfußbeulen (1)
- Pfahlnachgiebigkeiten (1)
- Physisoprtion (1)
- Piaui state (1)
- Pile Buckling (1)
- Pile Capacity (1)
- Pile ageing (1)
- Pile bending stiffness (1)
- Pile foundation (1)
- Pile groups (1)
- Pile retrofit system (1)
- Pile-Tip-Buckling (1)
- Point Cloud (1)
- Predictive maintenance (1)
- Pressure (1)
- Probabilistic modelling (1)
- Probabilitische Ingenieurmodelle (1)
- Probability of detection (1)
- Probekörpergeometrien (1)
- Process noise (1)
- Prognose (1)
- Propagation from a tunnel (1)
- Quasi-static response; (1)
- Rail roughness (1)
- Railbridge (1)
- Railway induced vibration (1)
- Railway track (1)
- Railway tracks (1)
- Railway trafiic (1)
- Randelementmethode (1)
- Random dynamics and vibrations (1)
- Random stiffness variation (1)
- Rayleighwellendispersion (1)
- Rechenverfahren (1)
- Recovery experiments (1)
- Referenzbeispiel (1)
- Remote sensing vibrometer (1)
- Residential building (1)
- Richtige Fahrzeugmasse (1)
- Richtlinie (1)
- Rigid vehicle model (1)
- Risiko (1)
- Risikoanalyse (1)
- Risk-based design (1)
- Risk-based maintenance planning (1)
- Rissprozes (1)
- Rissprozess (1)
- Road bridges (1)
- SHCC (1)
- SHM Environmental (1)
- SHM environmental bridges (1)
- Sandstone (1)
- Santa-marta (1)
- Scaling (1)
- Schadensüberwachung (1)
- Scherwellengeschwindigkeit (1)
- Schienenfahrweg (1)
- Schienenfahrwege (1)
- Schrauben (1)
- Schubmodul (1)
- Schwingungsmessungen (1)
- Schwingungsmonitoring (1)
- Schädigungsprozesse (1)
- Sensitivity vectors (1)
- Serra da cangalha (1)
- Shearing (1)
- Shell buckling (1)
- Shrinkage (1)
- Shrinkage Reducing Admixture (1)
- Sicherheit (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Simulation and experiment (1)
- Site-characterization (1)
- Soft impact (1)
- Soft track elements (1)
- Soil Struture Interaction (1)
- Soil forces (1)
- Soil stiffness (1)
- Soil-building interaction (1)
- Soil-building resonance (1)
- Soil-wall floor model (1)
- Soil-water-structure interaction (1)
- Sorption isotherm (1)
- Spatially varying ground conditions (1)
- Spektralanalyse (1)
- Stability Buckling soil-structure-interaction piles offshore (1)
- Stabilität (1)
- State of stress (1)
- Static loading (1)
- Statistical correlations (1)
- Statistical pattern recognition (1)
- Statistische Auswertung (1)
- Statistische Korrelationen (1)
- Stiffness variation (1)
- Stochastic Subspace Damage Detection (1)
- Strain (1)
- Stress stiffening (1)
- Stress-strain relation (1)
- Stress–strain-relation (1)
- Structural Systems (1)
- Structural integrity (1)
- Structural integrity maintenance (1)
- Structural integrity management (1)
- Structural system identification (1)
- Störgrößen (1)
- Substructures (1)
- Superplasticizer (1)
- Supplementary Cementitious Materials (1)
- Support structures (1)
- Surface Foundation (1)
- Surface line (1)
- Sustainable binders (1)
- Switch (1)
- Systemidentifikation (1)
- TOP (1)
- TRC (1)
- Tagung (1)
- Temperature effect (1)
- Temperature effect rejection (1)
- Temperature modeling (1)
- Temperatureinflüsse (1)
- Tensile test (1)
- Test specification (1)
- Tip Buckling (1)
- Track and vehicle irregularities (1)
- Track beam (1)
- Track damage monitoring (1)
- Track damage quantification (1)
- Track deflection (1)
- Track displacements (1)
- Track filter (1)
- Track filtering (1)
- Track vibration (1)
- Tragfähigkeit (1)
- Tragstrukturen (1)
- Train configuration (1)
- Train passages (1)
- Train-induced vibration (1)
- Tran speed (1)
- Transfer fuction (1)
- Transfer function (1)
- Transverse butt weld (1)
- Trench (1)
- Truss structures (1)
- Tunnel line (1)
- Tunnel-pile transfer (1)
- Tunnel-to-surface reduction (1)
- Tunnelstrecke (1)
- Turnout (1)
- UAS (1)
- Un- certainty (1)
- Unbounded domain (1)
- Under-sleeper pads (1)
- Value of information (1)
- Variational Bayesian statistics (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Varying track stiffness (1)
- Vibration analysis (1)
- Vibration excitation (1)
- Vibration monitoring (1)
- Viscosity (1)
- Vorspannung (1)
- Wahrscheinlichkeit (1)
- Water Science and Technology (1)
- Water-structure interaction (1)
- Wave propagation (1)
- Wave-Tower interaction (1)
- Wavenumber domain (1)
- Wavenumber integrals (1)
- Wavenumber method (1)
- Waves (1)
- Weld imperfections (1)
- Welded (1)
- Wellenfeldberechnung (1)
- Wheelset (1)
- Wheelset accelerations (1)
- Wind Energy Structures (1)
- Wind energy tower (1)
- Wind turbines (1)
- Wind-farm aerodynamics (1)
- Windenergieanlage (1)
- Windfarm wake analysis (1)
- Workability (1)
- Zerstreute Achsimpulse (1)
- building information modelling (1)
- elastische Gebäudelagerungen (1)
- fachwerkartige Stahltragwerken (1)
- layered soil (1)
- risk, reliability, inspection planning, offshore wind turbines (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- temperature (1)
- zerstreute Achslastimpulse (1)
- Übertragungsmatrizen (1)
- Überwachung (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (337) (entfernen)
Paper des Monats
- ja (5)
Deep foundations for offshore wind turbines. Lecture 2: lateral behaviour and advanced topics
(2020)
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
Due to the wide range of applications, the easy production and the large field of use, reinforced concrete (RC) is a widespread building material. This variety of applications is reflected in a wide range of physical material properties. Not only therefor it still is a technical challenge to provide all necessary test conditions for experimentally reproducing dynamic effects under impact loading of RC structures. In this paper we present investigations on the thicknesses of RC plates under low and medium high velocity impact loading by a flat-tipped impactor. The planar tomography setup at BAM is used to visualize the impact damage and to characterize the damage features such as cracks, scabbing and spalling. Further, the comparison of tomography results with those of an applied numeric simulation analysis is used to verify the numeric models for future damage prognosis under impact loading. Using the results of both, the tomographic as well as the FE analysis, different damage features were investigated and compared regarding their validity. Crack damage plays a leading part and the significance of summarized crack values as well as their distribution is analyzed. The total damage value but also the determined damage distribution both provide an input for describing damage as a function of the impactor velocity and plate thickness.
Classic non-destructive fatigue crack detection methods reveal the state of the fatigue damage evolution at the moment of application, generally not under operational conditions. The here introduced crack luminescence method realizes a clear visibility of the occurred and growing crack in loaded components during operation. Different established experiments show that due to the sensitive coating a crack Formation can be detected even in early stage under the premise the crack reached the surface. The coating consists of two layers with different properties and functions. The bottom layer emits light as fluorescence under UV radiation. The top layer covers the fluorescing one and prevents the emitting of light in case of no damage at the surface. In case of surface crack occurrence, the luminescent light is clearly noticeable by visual observations and also by standard camera equipment which makes automated crack detection possible as well. It is expected that crack luminescence can increase structural safety as well as reduce costs and time for inspections and preventive maintenance.
The passage of the train is dominated by the impulses of the static axle loads. The response of the regular homogeneous and irregular soils has been calculated by the finite-element method in frequency domain. The superposition of the impulse responses yields the quasi-static component of the ground vibration which is restricted to very low frequencies and to the close near-field of the track. In case of an irregular soil or ballast of which the stiffness varies randomly in space, a mid-frequency ground vibration component is generated by the scattering of the axle impulses. Measurements will be shown which prove the existence of the mid-frequency ground vibration component and the unique explanation by the scattered axle impulses: many international measurements with a raised mid-frequency component, axle-box measurements with a too low mid-frequency dynamic load, amplitude-speed dependencies which are incompatible with irregularity-induced dynamic loads, and ground vibration reductions due to stiff track elements.
In the last three decades, the vibrations of many floors and bridges have been measured. The contribution shows some evaluation methods, experimental results and some modelling and theoretical results. Simple evaluation methods have been developed for single and coupled floors. Two coupled beams have been measured in good agreement with the theory. A more complex coupling model has been found for a large wooden floor in a castle consisting of six floor bays which correlates well with the measurements. Damaged and intact poles have been tested by their natural frequencies and damping values, and a fair correlation between the degree of damage and the shift of the frequency. Road bridges have been analysed in detail and some examples are presented. Railway bridges and trains are studied for resonant excitation. The risk of resonance can be estimated in frequency domain by using axle-sequence spectra of the train and the natural frequencies of the bridge. A measurement example shows the amplification, but even stronger the cancellation of the subsequent axle responses. Several high-speed trains and freight trains have been analysed for their potential resonance amplification.
The passage of the train is dominated by the impulses of the static axle loads. The response of the regular homogeneous and irregular soils has been calculated by the finite-element method in frequency domain. The superposition of the impulse responses yields the quasi-static component of the ground vibration which is restricted to very low frequencies and to the close near-field of the track. In case of an irregular soil or ballast of which the stiffness varies randomly in space, a mid-frequency ground vibration component is generated by the scattering of the axle impulses. Measurements will be shown which prove the existence of the mid-frequency ground vibration component and the unique explanation by the scattered axle impulses: many international measurements with a raised mid-frequency component, axle-box measurements with a too low mid-frequency dynamic load, amplitude-speed dependencies which are incompatible with irregularity-induced dynamic loads, and ground vibration reductions due to stiff track elements.
In the last three decades, the vibrations of many floors and bridges have been measured. The contribution shows some evaluation methods, experimental results and some modelling and theoretical results. Simple evaluation methods have been developed for single and coupled floors. Two coupled beams have been measured in good agreement with the theory. A more complex coupling model has been found for a large wooden floor in a castle consisting of six floor bays which correlates well with the measurements. Damaged and intact poles have been tested by their natural frequencies and damping values, and a fair correlation between the degree of damage and the shift of the frequency. Road bridges have been analysed in detail and some examples are presented. Railway bridges and trains are studied for resonant excitation. The risk of resonance can be estimated in frequency domain by using axle-sequence spectra of the train and the natural frequencies of the bridge. A measurement example shows the amplification, but even stronger the cancellation of the subsequent axle responses. Several high-speed trains and freight trains have been analysed for their potential resonance amplification.
This article deals with two topics of vehicle-track-soil interaction, the mitigation of railway induced ground vibration by soft track elements, and the identification of track damage. Theoretical results have been achieved by a combined finite-element boundary-element method (FEBEM). The theoretical results are confronted with measurements at four sites. Improved mitigation effects have been found for soft rail pads under heavy sleepers. The insertion loss, however, can be too optimistic if a strong vehicle track resonance occurs for the un-isolated reference track. Two measurement sites show this strong vehicle-track resonance at about 80 Hz, which has been approximated by using the results of a wide parameter study including the rail pad, ballast, and soil stiffness, as well as the ballast model and the soil layering. – The detection of slab track damage is mainly based on the differences of the receptance or compliance functions. Theoretical results have been confirmed by measurements at one site where a loss of contact between track plate and base layer was visible. Measurements at a second site with a hidden damage have been compared with the theoretical results of a loose sleeper. The differences between intact (or repaired) and damaged tracks are strong enough to encourage the further development of this method for the identification of track damages.
This paper proposes a novel method to estimate the lateral displacement of high-rise structures under wind loads. The coefficient β(x) is firstly derived, reflecting the relation between the structural lateral dynamic displacement and the inclination angle at the height x of a structure. If the angle is small, it is the ratio between the structural fundamental mode shape and its first-order derivative without influence of external loads. Several dynamic experiments of structures are performed based on a laser remote sensing vibrometer and an inclinometer, which shows that the fundamental mode is dominated in the structural displacement response under different types of excitations. Once the coefficient β(x) is curve-fitted by measuring both the structural lateral dynamic displacement and the inclination angle synchronously, the real-time structural lateral displacement under operational conditions is estimated by multiplying the coefficient β(x) with the inclination angle. The advantage of the proposed method is that the coefficient β(x) can be identified by lateral dynamic displacement measured in high resolution by the remote sensing vibrometer, which is useful to reconstruct the displacement accurately by the inclination angle under operational conditions
The erosion of natural sediments by a superficial fluid flow is a generic situation in many usual geological or industrial contexts. However, there is still a lack of fundamental knowledge about erosional processes, especially concerning the role of internal cohesion and adhesive stresses on issues such as the critical flow conditions for the erosion onset or the kinetics of soil mass loss. This contribution investigates the influence of cohesion on the surface erosion by an impinging jet flow based on laboratory tests with artificially bonded granular materials. The model samples are made of spherical glass beads bonded either by solid bridges made of resin or by liquid bridges made of a highly viscous oil. To quantify the intergranular cohesion, the capillary forces of the liquid bridges are here estimated by measuring their main geometrical parameters with image-processing techniques and using well-known analytical expressions. For the solid bonds, the adhesive strength of the materials is estimated by direct measurement of the yield tensile forces and stresses at the particle and sample scales, respectively, with specific traction tests developed for this purpose. The proper erosion tests are then carried out in an optically adapted device that permits a direct visualization of the scouring process at the jet apex by means of the refractive index matching technique. On this basis, the article examines qualitatively the kinetics of the scour crater excavation for both scenarios, namely, for an intergranular cohesion induced by either liquid or solid bonds. From a quantitative perspective, the critical condition for the erosion onset is discussed specifically for the case of the solid bond cohesion. In this respect, we propose here a generalized form of the Shields criterion based on a common definition of a cohesion number from yield tensile values, derived at both micro- and macroscales. The article finally shows that the proposed form manages to reconcile the experimental data for cohesive and cohesionless materials, the latter in the form of the so-called Shields curve along with some previous results of the authors which have been appropriately revisited.
The stability and geometric nonlinearities of slender structures are a major topic in structural design. While this topic is most relevant in the field of Structural Engineering, e.g. for steel or concrete structures, only few applications take the role of soil-structure-interaction explicitly into account. The focus of this paper is placed on the impact of soil support and its modelling for the buckling analysis based on examples both for pile foundations and for railway track stability. The general interaction between steel design and the geotechnical input will be addressed. The paper discusses and summarizes a range of subtopics based on experience and current research at the author’s institute.
The train passages over intact or damaged slab tracks on different soils have been calculated by the finite-element boundary-element or the wavenumber-domain method. The influence of track and soil parameters on the distribution of the track displacements and the soil forces has been analysed. The measured and calculated displacement time histories of train passages could be used to identify track damages such as lose sleepers or a lose track plate. The time histories and spectra of the soil forces can explain the measured ground vibration reduction of slab tracks. The calculated displacement and force distributions of slab tracks on continuous soils do not fulfil the Winkler hypothesis and Winkler models should not be used for track analysis.
Die gesamte Prognose wurde rechnerisch erfasst. Die Rechenverfahren sind einfach und schnell. Die Emission und die Immission verwendet Übertragungsmatrizen. Die Transmissionsrechnung beruht auf der Dispersion der Rayleighwelle. Die Verknüpfung erfolgt über die Anregungskraft auf den Boden und über die Freifeldamplitude am Gebäude.
Es sind viele Eingabemöglichkeiten für Messdaten vorgesehen. Messungen können von einem Ort auf einen anderen Ort übertragen werden.
We present here a set of conceptual and numerical tools for a micromechanical simulation of general erosion problems involving fluid-saturated granular assemblies, whether frictional or cohesive. We propose a parallel computation using graphical processing units (GPUs) to treat large numbers of degrees of freedom with conventional desktop computers.
The fluid phase is here simulated with a particle-resolved approach in the frame of the Lattice Boltzmann Method (LBM) while the granular solid phase is modelled as a collection of discrete particles from a Molecular Dynamics DEM perspective. The range of possible material behaviors for the solid granular phase is intended here to cover a broad spectrum from purely frictional to viscous cohesive materials with either brittle or transient debonding features. Specific details of the implementation and some validation cases will be put forward.
To conclude we provide some exemplary applications in the field of soil erosion along with details on the parallel performance of the models. The results show that a micromechanical approach can be feasible and useful in practice, providing meaningful insights into complex phenomena like the erosion threshold and kinetics of weakly cemented soils.
Prediction of dynamic effects of reinforced concrete structures under impact loading is a technical challenge. This is a consequence of the great variability of the physical properties resulting from the wide adaptability of reinforced concrete and a consequence of the wide range of impact loading. Experiments and numerical investigations are normally used on a small scale to address the problem. In this paper, impact tests on reinforced conrete plates with the lateral dimensions of 1.5 m x 1.5 m and a thickness of 30 cm are presented. In bending reinforcement, besides the velocity two properties are varied, the diameter and the spatial distribution of the rebars. Experiments are performed at the Otto-Mohr-Laboratory of the Institute of Concrete Structures of the Technische Universit¨at Dresden. Due to the accelerated fall of the impactor the velocity ranges between 20 and 70 m/s. In addition to the measured quantities such as bearing forces, accelerations are also measured at 4 different positions on and under the plate, as well as the deflection at several positions. The measured data are used for the analysis of the damage form and the numerical examinations with the program Ansys Autodyn and the material model after Drucker-Prager. Numerical investigations support the tests, with detailed analysis of individual effects. These numerical computations and the planar tomographic investigations were carried out at BAM in Berlin. With the help of planar tomographic evaluation, the damaged structure is made visible and compared with the numerical results. Influences of the bending reinforcement are explained on the basis of damage evaluation in the local area and on selected measured values. In addition to the test evaluation, the tomographic and numerical methods are presented.
Prediction of dynamic effects of reinforced concrete structures under impact loading is a technical challenge. This is a consequence of the great variability of the physical properties resulting from the wide adaptability of reinforced concrete and a consequence of the wide range of impact loading. Experiments and numerical investigations are normally used on a small scale to address the problem. In this paper, impact tests on reinforced conrete plates with the lateral dimensions of 1.5 m x 1.5 m and a thickness of 30 cm are presented. In bending reinforcement, besides the velocity two properties are varied, the diameter and the spatial distribution of the rebars. Experiments are performed at the Otto-Mohr-Laboratory of the Institute of Concrete Structures of the Technische Universit¨at Dresden. Due to the accelerated fall of the impactor the velocity ranges between 20 and 70 m/s. In addition to the measured quantities such as bearing forces, accelerations are also measured at 4 different positions on and under the plate, as well as the deflection at several positions. The measured data are used for the analysis of the damage form and the numerical examinations with the program Ansys Autodyn and the material model after Drucker-Prager.
Numerical investigations support the tests, with detailed analysis of individual effects. These numerical computations and the planar tomographic investigations were carried out at BAM in Berlin. With the help of planar tomographic evaluation, the damaged structure is
made visible and compared with the numerical results. Influences of the bending reinforcement are explained on the basis of damage evaluation in the local area and on selected measured values. In addition to the test evaluation, the tomographic and numerical methods are presented.
At the Bundesanstalt für Materialforschung und -prüfung (BAM) full scale specimens for nuclear transport and storage containers (casks) are tested for their structural integrity in a series of drop tests on the Test Site Technical Safety in Horstwalde, 50 km south of Berlin. These drop tests cause a major stress not only on the casks, but also on the steel tower structure of the test facility, itself. The load pattern makes the structure very interesting for detailed investigation. The focus of the monitoring lies on the bolted joints of the flange connections that are a typical connection for cylindrical elements if welding is technical or economical unfavorable. The definition of the monitoring takes was done by investigating the existing documents and inspection results accompanied by building an initial digital representation of the structure, consisting of two finite element (FE) models and a geometrical 3D point cloud representation. As a first step the structures behavior during static and dynamic loading was analyzed using measurement data and an updated numerical FE Model. The idea behind is to use models for a digital planning and operation/evaluation of the structural health monitoring. A static FE simulation and a dynamic FE simulation are generated, to investigate how the structure behaves under the load conditions.
A study on building vibrations has been performed by finite element calculations. Family houses, multi-storey residential buildings, office buildings and office towers have been modelled in detail. The frequency-dependent response due to a free-field excitation has been evaluated for walls, columns and floors. The ratio of building amplitudes to free-field amplitudes starts with uB/u0 = 1 at zero frequency and is usually lower than 1 at 50 Hz, the end of the frequency range considered here. In between, amplifications occur due to several reasons. There are „soil resonances“ where the whole building is vibrating on the compliant soil, “column resonances” where the upper storeys are vibrating on the compliant columns, and the “floor resonances” where the floors are vibrating excited by their supports. Results are presented for all building types, but a special focus is set on office buildings. A parameter study shows the influence of the stiffness of the soil, the number of storeys, and the width of the building. It has been found that the “soil resonance” is strongly modified by the low-frequency floor resonances for the normal office building. The main resonance of a twenty-storey office tower is determined equally by the “soil mode” and the “column mode”. It is an important observation for these office buildings that the resonances can differ for different parts of the building such as the centre, the edge, the corner, and the core of the building. This leads to non-uniform vibration modes across the building, which look like another type of “floor resonance” and which have been observed in several real building projects. Experimental results will be shown which can confirm the calculated phenomena.
A study on building vibrations has been performed by finite element calculations. Family houses, multi-storey residential buildings, office buildings and office towers have been modelled in detail. The frequency-dependent response due to a free-field excitation has been evaluated for walls, columns and floors. The ratio of building amplitudes to free-field amplitudes starts with uB/u0 = 1 at zero frequency and is usually lower than 1 at 50 Hz, the end of the frequency range considered here. In between, amplifications occur due to several reasons. There are „soil resonances“ where the whole building is vibrating on the compliant soil, “column resonances” where the upper storeys are vibrating on the compliant columns, and the “floor resonances” where the floors are vibrating excited by their supports. Results are presented for all building types, but a special focus is set on office buildings. A parameter study shows the influence of the stiffness of the soil, the number of storeys, and the width of the building. It has been found that the “soil resonance” is strongly modified by the low-frequency floor resonances for the normal office building. The main resonance of a twenty-storey office tower is determined equally by the “soil mode” and the “column mode”. It is an important observation for these office buildings that the resonances can differ for different parts of the building such as the centre, the edge, the corner, and the core of the building. This leads to non-uniform vibration modes across the building, which look like another type of “floor resonance” and which have been observed in several real building projects. Experimental results will be shown which can confirm the calculated phenomena.
Fault detection for linear parameter varying systems under changes in the process noise covariance
(2020)
Detecting changes in the eigenstructure of linear systems is a comprehensively investigated subject. In particular, change detection methods based on hypothesis testing using Gaussian residuals have been developed previously. In such residuals, a reference model is confronted to data from the current system. In this paper, linear output-only systems depending on a varying external physical parameter are considered. These systems are driven by process noise, whose covariance may also vary between measurements. To deal with the varying parameter, an interpolation approach is pursued, where a limited number of reference models -- each estimated from data measured in a reference state -- are interpolated to approximate an adequate reference model for the current parameter. The problem becomes more complex when the different points of interpolation correspond to different noise conditions. Then conflicts may arise between the detection of changes in the eigenstructure due to a fault and the detection of changes due to different noise conditions. For this case, a new change detection approach is developed based on the interpolation of the eigenstructure at the reference points. The resulting approach is capable of change detection when both the external physical parameter and the process noise conditions are varying. This approach is validated on a numerical simulation of a mechanical system.
The surface erosion of soil samples caused by an impinging jet can be analyzed using the jet erosion test (JET), a standard experimental test to characterize the erosion resistance of soils. This paper specifically addresses the flow characteristics of a laminar impinging jet over the irregular surface of granular beds to discuss the pertinence and relevance of commonly used empirical estimations based on a selfsimilar model of a free jet. The JET is here investigated at the microscale with a coupled fluid-particle flow numerical odel featuring the lattice Boltzmann method (LBM) for the fluid phase combined with the discrete element method (DEM) for the mechanical behavior of the solid particles. The hydrodynamics of a laminar plane free jet are confronted with the results from a parametric study of jet impingement, both on solid smooth and fixed granular surfaces, that take into account variations in particle size, distance from jet origin, and jet Reynolds number. The flow characteristics at the bed surface are here quantified, including the maximal values in tangential velocity and wall shear stress, which can be regarded as the major cause of particle detachments under hydrodynamic solicitation. It is shown that the maximal velocity at the impinged surface can be described by the free jet self-similar model, provided that a simple empirical coefficient is introduced. Further, an expression is proposed for the maximal shear stress in laminar conditions, including a Blasius-like friction coefficient that is inversely proportional to the square root of the jet Reynolds number. To conclude, finally, the JET erosion of different cohesionless granular samples is analyzed, confirming that the threshold condition at the onset of granular motion is consistent with the Shields diagram and in close agreement with previous experimental results.
Eindimensionale Modelle des Gleises aus einem Schienenstützpunkt, zweidimensionale Modelle enthalten die Kraftverteilung der Schiene. Eindimensionale Modelle machen einen Fehler, weil sie eine zu große Fahrzeugmasse berücksichtigen. Man kann jedoch bei der Berechnung der Minderungswirkung von Gleiselementen eindimensionale Gleismodelle verwenden, um die Kraftübertragung des Gleises bzw. die Minderungswirkung des Gleises zu berechnen. Die Wechselwirkung mit dem Fahrzeug kann einfach mit der dynamischen Stützpunktsteifigkeit berechnet werden. Dabei muss die Stützpunktsteifigkeit mit einer charakteristischen Gleislänge multipliziert werden, die frequenz- und systemabhängig ist.
This article deals with the relevance and practical feasibility of micromechanical simulations for their application to general geomechanical problems involving fluid-saturated granular assemblies, whether frictional or cohesive. A set of conceptual and numerical tools is here presented, advocating for a parallel computation using graphical processing units (GPUs) to treat large numbers of degrees of freedom with conventional Desktop computers. The fluid phase is here simulated with a particle-resolved approach in the frame of the Lattice Botzmann Method (LBM) while the granular solid phase is modelled as a collection of discrete particles from a Molecular Dynamics DEM perspective. The range of possible material behaviours for the solid granular phase is intended here to cover a broad spectrum from purely frictional to viscous cohesive materials with either brittle or transient debonding features. Specific details of the implementation and some validation cases are put forward.
Finally, some exemplary applications in the fields of soil erosion and geotechnical profile installation are provided along with a discussion on the parallel performance of the presented models. The results show that a micromechanical approach can be feasible and useful in practice, providing meaningful insights into complex engineering problems like the erosion kinetics of a soil under an impinging jet or the penetration resistance of a deep foundation in a layered soil profile.
A strain-based automated operational modal analysis algorithm is proposed to track the long-term dynamic behavior of a horizontal wind turbine under operational conditions.
This algorithm is firstly validated by a scaled wind turbine model, and then it is applied to the dynamic strain responses recorded from a 5 MW wind turbine system. We observed variations in the fundamental frequency and 1f, 3f excitation frequencies due to the mass imbalance of the blades and aerodynamic excitation by the tower dam or tower wake. Inspection of the Campbell diagram revealed that the adverse resonance phenomenon and Sommerfeld effect causing excessive vibrations of the wind tower.
State of the art and development perspectives of deep foundations for offshore wind converters
(2020)
This presentation provides an overview of the main geotechnical aspects associated with deep foundations in the context of offshore wind generation. The most common deep foundation typologies (large diameter monopiles and multipile typologies) as well as new trends under development (e.g. suction buckets) and their current limits will be briefly described. The talk concludes with a brief review of advanced topics not covered in classical pile design, such as hydromechanical coupling effects (pore pressure generation), cyclic accumulation of deformations, cyclic degradation of axial capacity or pile-setup gains.
At the Bundesanstalt für Materialforschung und -prüfung (BAM) full scale specimens for nuclear transport and storage containers (casks) are tested for their structural integrity in a series of drop tests on the Test Site Technical Safety in Horstwalde, 50 km south of Berlin. These drop tests cause a major stress not only on the casks, but also on the steel tower structure of the test facility, itself. The load pattern makes the structure very interesting for detailed investigation. The focus of the monitoring lies on the bolted joints of the flange connections that are a typical connection for cylindrical elements if welding is technical or economical unfavorable. The definition of the monitoring takes was done by investigating the existing documents and inspection results accompanied by building an initial digital representation of the structure, consisting of two finite element (FE) models and a geometrical 3D point cloud representation. As a first step the structures behavior during static and dynamic loading was analyzed using measurement data and an updated numerical FE Model. The idea behind is to use models for a digital planning and operation/evaluation of the structural health monitoring. A static FE simulation and a dynamic FE simulation are generated, to investigate how the structure behaves under the load conditions.
Fault detection for linear parameter varying systems under changes in the process noise covariance
(2020)
Detecting changes in the eigenstructure of linear systems is a comprehensively investigated subject. In particular, change detection methods based on hypothesis testing using Gaussian residuals have been developed previously. In such residuals, a reference model is confronted to data from the current system. In this paper, linear output-only systems depending on a varying external physical parameter are considered. These systems are driven by process noise, whose covariance may also vary between measurements. To deal with the varying parameter, an interpolation approach is pursued, where a limited number of reference models – each estimated from data measured in a reference state – are interpolated to approximate an adequate reference model for the current parameter. The problem becomes more complex when the different points of interpolation correspond to different noise conditions. Then conflicts may arise between the detection of changes in the eigenstructure due to a fault and the detection of changes due to different noise conditions. For this case, a new change detection approach is developed based on the interpolation of the eigenstructure at the reference points. The resulting approach is capable of change detection when both the external physical parameter and the process noise conditions are varying. This approach is validated on a numerical simulation of a mechanical system.
Fault detection for linear parameter varying systems under changes in the process noise covariance
(2020)
Detecting changes in the eigenstructure of linear systems is a comprehensively investigated subject. In particular, change detection methods based on hypothesis testing using Gaussian residuals have been developed previously. In such residuals, a reference model is confronted to data from the current system. In this paper, linear output-only Systems depending on a varying external physical parameter are considered. These systems are driven by process noise, whose covariance may also vary between measurements. To deal with the varying parameter, an interpolation approach is pursued, where a limited number of reference models { each estimated from data measured in a reference state { are interpolated to approximate an adequate reference model for the current parameter. The problem becomes more complex when the different points of interpolation correspond to different noise conditions. Then con icts May arise between the detection of changes in the eigenstructure due to a fault and the detection of changes due to different noise conditions. For this case, a new change detection approach is developed based on the interpolation of the eigenstructure at the reference points. The resulting approach is capable of change detection when both the external physical parameter and the process noise conditions are varying. This approach is validated on a numerical simulation of a mechanical system.
Inspection and maintenance contribute significantly to the lifetime cost of bridges. There is significant potential in using information obtained through structural health monitoring to update predictive models of the condition and performance of such structures, and thus ena-ble an improved decision-making regarding inspection and maintenance activities. Within the AISTEC project funded by the German Federal Ministry of Education and Research, we develop vibration-based structural health monitoring systems aimed at continuously provid-ing information on the structural condition of bridges. Environmental variations such as changing ambient temperatures can significantly influence the dynamic characteristics of bridges and thus mask the effect of structural changes and damages. It remains a challenge to account for such influences in structural health monitoring. To study the effect of ambient temperatures on the dynamic characteristics of beam structures, we monitor the vibration response of a reinforced concrete beam in the uncracked and cracked state at varying tem-peratures in a climate chamber. We postulate a set of competing parameterized probabilistic structural models, which explicitly account for the effect of varying ambient temperatures on the mechanical properties of the system. We then combine the information provided by the structural models with the information contained in the recorded vibration data to learn the parameters of the temperature-dependent structural models and infer the plausible state of the beam using Bayesian system identification and model class selection.
Kontinuierliche sensorbasierte Bauwerksmessungen leisten einen wichtigen Beitrag zur Sicherheit von Verkehrsbauwerken. Hierzu werden im Vorhaben AISTEC Referenzbauwerke und Referenzverfahren untersucht mit Schwerpunkt auf den Einfluss klimatischer Bedingungen. Der Vortrag stellt den aktuellen Projektstand des FB 7.2 vor.
Reliability analysis of deteriorating structural systems requires the solution of time-variant reliability problems.
In the general case, both the capacity of and the loads on the structure vary with time. This analysis can be approached by approximation through a series of time-invariant reliability problems, which is a potentially effective strategy for cases where direct solutions of the time-variant reliability problem are challenging, e.g. for structural systems with many elements or arbitrary load processes. In this contribution, we thoroughly Review the formulation of the equivalent time-invariant reliability problems and extend this approximation to structures for which inspection and monitoring data is available. Thereafter, we present methods for efficiently evaluating the reliability over time. In particular, we propose the combination of sampling-based methods with a FORM (first-order reliability method) approximation of the series system reliability problem that arises in the computation of the lifetime reliability. The framework and algorithms are demonstrated on a set of numerical examples, which include the computation of the reliability conditional on inspection data.
The current practice of operating and maintaining deteriorating structural systems ensures acceptable levels of structural reliability, but it is not clear how efficient it is. Changing the current prescriptive approach to a risk-based approach has great potential to enable a more efficient management of such systems. Risk-based optimization of operation and maintenance strategies identifies the strategy that optimally balances the cost for controlling deterioration in a structural system with the achieved risk reduction. Inspections and monitoring are essential parts of operation and maintenance strategies. They are typically performed to reduce the uncertainty in the structural condition and inform decisions on future operation and maintenance actions. In risk-based optimization of operation and maintenance strategies, Bayesian updating is used to include information contained in inspection and monitoring data in the prediction of the structural reliability. All computations need to be repeated many times for different potential inspection and monitoring outcomes. This motivates the development of robust and efficient approaches to this computationally challenging task.
The reliability of deteriorating structural systems is time-variant because the loads on them and their capacities change with time. In most practical applications, the reliability analysis of deteriorating structural systems can be approached by dividing their lifetime into discrete time intervals. The time-variant reliability problem can then be represented by a series of time-invariant reliability problems. Using this methodology as a starting point, this thesis proposes a novel approach to compute the time-variant reliability of deteriorating structural systems for which inspection and monitoring data are available. The problem is formulated in a nested way in which the prediction of the structural condition is separated from the computation of the structural reliability conditional on the structural condition. Information on the structural condition provided by inspections and monitoring is included in the reliability assessment through Bayesian updating of the system deterioration model employed to predict the structural condition. The updated system reliability is obtained by coupling the updated deterioration model with a probabilistic structural model utilized to calculate the failure probability conditional on the structural condition. This approach is the first main outcome of this thesis and termed nested reliability analysis (NRA) approach. It is demonstrated in two numerical examples considering inspected and monitored steel structures subject to high-cycle fatigue.
An alternative – recently developed – approach, which also follows the strategy of discretizing time, describes deteriorating structural systems with hierarchical dynamic Bayesian networks (DBN). DBN combined with approximate or exact inference algorithms also enable the computation of the time-variant reliability of deteriorating structural systems conditional on information provided by inspection and monitoring data. In this thesis – as a proof of concept – a software prototype is developed based on the DBN approach, which can be used to assess the reliability of a corroding concrete box girder for which half-cell potential measurements are available. This is the second main outcome of this thesis.
Both approaches presented in this thesis enable an integral reliability analysis of inspected and monitored structures that accounts for system effects arising from (a) the correlation among deterioration states of different structural elements, (b) the interaction between element deterioration and system failure, and (c) the indirect information gained on the condition of all unobserved structural elements from inspecting or monitoring the condition of some structural elements. Thus, both approaches enable a systemwide risk-based optimization of operation and maintenance strategies for deteriorating structural systems.
The NRA approach can be implemented relatively easily with subset simulation, which is a sequential Monte Carlo method suitable for estimating rare event probabilities. Subset simulation is robust and considerably more efficient than crude Monte Carlo simulation. It is, however, still sampling-based and its efficiency is thus a function of the number of inspection and monitoring outcomes, as well as the value of the simulated event probabilities. The current implementation of the NRA approach performs separate subset simulation runs to estimate the reliability at different points in time. The efficiency of the NRA approach with subset simulation can be significantly improved by exploiting the fact that failure events in different years are nested. The lifetime reliability of deteriorating structural systems can thus be computed in reverse chronological order in a single subset simulation run.
The implementation of the DBN approach is much more demanding than the implementation of the NRA approach but it has two main advantages. Firstly, the graphical format of the DBN facilitates the presentation of the model and the underlying assumptions to stakeholders who are not experts in reliability analysis. Secondly, it can be combined with exact inference algorithms. In this case, its efficiency neither depends on the number of inspection and monitoring outcomes, nor on the value of the event probabilities to be calculated. However, in contrast to the NRA approach with subset simulation, the DBN approach with exact inference imposes restrictions on the number of random variables and the dependence structure that can be implemented in the model.
Monitoringsysteme erfassen kontinuierlich Bauwerksdaten wie z.B. Bauwerksbeschleunigungen, auf deren Grundlage Bauwerksschäden mit Hilfe von SHM-Methoden quantifiziert werden können. Mit den gewonnenen Informationen über den aktuellen Bauwerkszustand können Vorhersagen des Bauwerkszustandes und der Bauwerkszuverlässigkeit aktualisiert und erforderliche Inspektionen und Instandhaltungsmaßnahmen vorausschauend geplant werden. Im BMBF-Forschungsvorhaben AISTEC entwickeln der Fachbereich 7.2 „Ingenieurbau“ innovative Monitoringverfahren zur Systemidentifikation und automatischen Detektion, Lokalisierung und Quantifizierung von Schäden an Infrastrukturbauwerken anhand von gemessenen dynamischen und statischen Bauwerksdaten. Im Rahmen dieses Projektes werden die Verfahren an der Maintalbrücke bei Gemünden angewendet, welche Teil der ICE-Strecke Hannover-Würzburg ist. In diesem Vortrag wird das für die Maintalbrücke Gemünden geplante und umgesetzte Monitoingsystem vorgestellt.
Inspection and maintenance contribute significantly to the lifetime cost of bridges. There is significant potential in using information obtained through structural health monitoring to update predictive models of the condition and performance of such structures, and thus ena-ble an improved decision-making regarding inspection and maintenance activities. Within the AISTEC project funded by the German Federal Ministry of Education and Research, we develop vibration-based structural health monitoring systems aimed at continuously provid-ing information on the structural condition of bridges. Environmental variations such as changing ambient temperatures can significantly influence the dynamic characteristics of bridges and thus mask the effect of structural changes and damages. It remains a challenge to account for such influences in structural health monitoring. To study the effect of ambient temperatures on the dynamic characteristics of beam structures, we monitor the vibration response of a reinforced concrete beam in the uncracked and cracked state at varying tem-peratures in a climate chamber. We postulate a set of competing parameterized probabilistic structural models, which explicitly account for the effect of varying ambient temperatures on the mechanical properties of the system. We then combine the information provided by the structural models with the information contained in the recorded vibration data to learn the parameters of the temperature-dependent structural models and infer the plausible state of the beam using Bayesian system identification and model class selection.
This article presents a solid cohesion model for the simulation of bonded granular assemblies in the frame of 3D discrete element approaches (DEM). A simple viscoplastic cohesion model for 2D geometries is extended to 3D conditions, while its yield criterion is generalized as a hyper-surface in the space of bond solicitations to include torsional moments. The model is then calibrated using experimental results of uniaxial traction at both the microscopic and macroscopic scales with an artificial granular cohesive soil. The paper finally presents some simulated results on the macromechanical sample traction application and briefly discusses the model's current limitations and promising prospects for subsequent works.
This article presents a solid cohesion model for the simulation of bonded granular assemblies in the frame of 3D discrete element approaches (DEM). A simple viscoplastic cohesion model for 2D geometries is extended to 3D conditions, while its yield criterion is generalized as a hyper-surface in the space of bond solicitations to include torsional moments. The model is then calibrated using experimental results of uniaxial traction at both the microscopic and macroscopic scales with an artificial granular cohesive soil. The paper finally presents some simulated results on the macromechanical sample traction application and briefly discusses the model's current limitations and promising prospects for subsequent works.
In this article, the passage of different trains over different bridges will be studied for resonant excitation. The intensity of the resonance will be estimated in frequency domain by using three separated spectra. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of the train. The influences of train speed, bridge length, bridge support, track irregularities, and train type on the resonance amplitudes will be analysed for each of these spectra separately for getting a better insight. A variety of axle-sequence spectra and corresponding rules will be presented for different vehicles and trains. As examples, the passage of a slow freight train over a long-span bridge, a normal passenger train over a medium-span bridge, and a high-speed train over a short bridge will be analysed. Corresponding measurements show the amplification, but also the cancellation of the subsequent axle responses. Namely in one of the measurement examples, the first mode of the bridge was amplified and the second mode was cancelled at a low speed of the train and vice versa at a higher speed.
Prediction of building noise and vibration – 3D finite element and 1D wave propagation models
(2021)
Construction work or traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for the inhabitants. The transfer of the vibration from the free field to the building has been calculated by the finite element method for many models in consultancy and research work. The analysis for all storeys of certain building points such as walls, columns and floors unveiled some rules, some typical modes, and some wavetype responses. A simplified building-soil model has been created, which includes well these effects of building-soil resonance, wall/column resonance, floor resonances, and the high-frequency reduction. The model consists of one wall for a wall-type apartment building or a column for each specific part (mid, side or corner) of a column-type office building. The building response in the high-frequency (acoustic) region is calculated as mean values over all storeys and over wider frequency bands, by wave-type asymptotes of an infinitely tall building, and by the soil to wall ratio of impedances. The secondary noise is predicted by Transfer values between the building vibration (center of floors, walls at a room corner) and the sound pressure.
Prediction of building noise and vibration – 3D finite element and 1D wave propagation models
(2021)
Construction work or traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for the inhabitants. The transfer of the vibration from the free field to the building has been calculated by the finite element method for many models in consultancy and research work. The analysis for all storeys of certain building points such as walls, columns and floors unveiled some rules, some typical modes, and some wavetype responses. A simplified building-soil model has been created, which includes well these effects of building-soil resonance, wall/column resonance, floor resonances, and the high-frequency reduction. The model consists of one wall for a wall-type apartment building or a column for each specific part (mid, side or corner) of a column-type office building. The building response in the high-frequency (acoustic) region is calculated as mean values over all storeys and over wider frequency bands, by wave-type asymptotes of an infinitely tall building, and by the soil to wall ratio of impedances. The secondary noise is predicted by Transfer values between the building vibration (center of floors, walls at a room corner) and the sound pressure.
Die Linienlastgesetzmäßigkeit gilt nicht für Zuganregung. Die Punktlastgesetzmäßigkeit wird bei kurzen Zügen in größeren Entfernungen erreicht. Bei langen Zügen reduziert sich die Abnahme um r-0,3 für die theoretische exponentielle Dämpfungsabnahme, um r-0,5 für die vereinfachte potentielle Dämpfungsabnahme. Die gemessenen Abnahmereduktionen liegen in diesem Bereich.
Structural health monitoring (SHM) of civil structures often is limited due to changing environmental conditions, as those changes affect the structural dynamical properties in a similar way like damages can do. In this article, an approach for damage detection under changing temperatures is presentedand applied to a beam structure. The used stochastic subspace-based algorithm relies on a reference null space estimate, which is confronted to data from the testing state in a residual function. For damage detection the residual is evaluated by means of statistical hypothesis tests. Changes of the system due to temperature effects are handled with a model interpolation approach from linear parameter varying system theory. From vibration data measured in the undamaged state at some few reference temperatures, a model of the dynamic system valid for the current testing temperature is interpolated. The reference null space and the covariance matrix for the hypothesis test is computed from this interpolated model. This approach has been developed recently and was validated in an academic test case on simulations of a mass-spring-damper. In this paper, the approach is validated experimentally on a beam structure under varying temperature conditions in a climate chamber. Compared to other approaches, the interpolation approach leads to significantly less false positive alarms in the reference state when the structure is exposed to different temperatures, while faults can still be detected reliably.
Structural health monitoring (SHM) of civil structures often is limited due to changing environmental conditions, as those changes affect the structural dynamical properties in a similar way like damages can do. In this article, an approach for damage detection under changing temperatures is presentedand applied to a beam structure. The used stochastic subspace-based algorithm relies on a reference null space estimate, which is confronted to data from the testing state in a residual function. For damage detection the residual is evaluated by means of statistical hypothesis tests. Changes of the system due to temperature effects are handled with a model interpolation approach from linear parameter varying system theory. From vibration data measured in the undamaged state at some few reference temperatures, a model of the dynamic system valid for the current testing temperature is interpolated. The reference null space and the covariance matrix for the hypothesis test is computed from this interpolated model. This approach has been developed recently and was validated in an academic test case on simulations of a mass-spring-damper. In this paper, the approach is validated experimentally on a beam structure under varying temperature conditions in a climate chamber. Compared to other approaches, the interpolation approach leads to significantly less false positive alarms in the reference state when the structure is exposed to different temperatures, while faults can still be detected reliably
Zur Erschütterungsausbreitung an oberirdischen Bahnlinien gibt es gute Übereinstimmungen zwischen Messungen und der Theorie geschichteter Böden. Bei der Interpretation der Ergebnisse spielt die Rayleigh-Welle eine große Rolle. Je nach Frequenz und Wellenlänge hat die Rayleigh-Welle eine bestimmte Eindringtiefe und erreicht damit mehr oder weniger steife Bodenschichten. Damit bekommt man eine frequenzabhängige Bodensteifigkeit für die Erschütterungsprognose. Für die Wellenausbreitung in der Tiefe statt an der Bodenoberfläche müssen eigene Gesetzmäßigkeiten gefunden werden. Es werden die Punktlastlösungen im Frequenz-Wellenzahlbereich und durch Integration über die Wellenzahlen berechnet. Man erhält die Wellenfelder, die Terzspektren für verschiedene Entfernungen und Frequenzen. Es wird die Tiefenlage und das Bodenmodell (homogen, geschichtet und kontinuierlich zunehmende Steifigkeit) variiert. Die Rayleigh-Welle verliert ihre Bedeutung und stattdessen kann die Vollraumlösung zur Interpretation und Prognose verwendet werden. Es werden die Halbraumlösung mit und ohne Rayleigh-Welle und die Vollraumlösung in der Tiefe diskutiert und verglichen. Neben der Wellenausbreitung (der Transmission) werden auch Effekte der Erschütterungsanregung (der Emission) und der Übertragung in Gebäude (der Immission) mit Hilfe der Finite-Element-Randelement-Methode berechnet. Die Verteilung der dynamischen Achslast durch die Tunnelsohle ergibt eine Minderung gegenüber der Punktlastanregung. Bei der Immission hat man keine Freifeldanregung wie an der Bodenoberfläche. Man muss entweder neben der Wellenamplitude (Verschiebung oder Schwinggeschwindigkeit) in der Tiefe auch die Spannung der ankommenden Welle berücksichtigen, oder man muss die Freifeldamplituden nach Bodenaushub berechnen. Die Rechenergebnisse deuten darauf hin, dass man als Freifeldanregung die zweifache Vollraumlösung ansetzen kann.
The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site.
There is a strong need for cost-effective mitigation measures for
turnouts. SBB has initiated a series of examinations using different methodologies to gain a deeper understanding of the excitation mechanisms at low frequencies, in addition to that obtained in the RIVAS project. To date it is not yet clear what constitutes a complete measurement data set that would enable understanding most of the vibration excitation mechanisms in turnouts. Increasing vibration at turnouts in comparison to normal track is observed for all measured frequencies.
The different methodologies are presented in the paper. Under-sleeper pads (USP) are a cost-effective method to reduce vibration at frequencies above 63 Hz (1/3 octave), but there is probably no improvement for frequencies below 63 Hz. A first test of new frog geometry did not show relevant improvements in Vibration emission in comparison to a reference frog geometry. Axle box acceleration measurements are an interesting method to identify defects in a turnout. A specialized measurement system of rail roughness could identify certain geometry Problem areas for some frogs. Noise increases also are observed at turnouts for frequencies ranging between 80 to 1000 Hz. The use of railway source models to calculate
contact forces for ballasted track and turnouts seems promising, in particular for understanding the influence of ground.
Zur Erschütterungsausbreitung an oberirdischen Bahnlinien gibt es gute Übereinstimmungen zwischen Messungen und der Theorie geschichteter Böden. Bei der Interpretation der Ergebnisse spielt die Rayleigh-Welle eine große Rolle. Je nach Frequenz und Wellenlänge hat die Rayleigh-Welle eine bestimmte Eindringtiefe und erreicht damit mehr oder weniger steife Bodenschichten. Damit bekommt man eine frequenzabhängige Bodensteifigkeit für die Erschütterungsprognose. Für die Wellenausbreitung in der Tiefe statt an der Bodenoberfläche müssen eigene Gesetzmäßigkeiten gefunden werden. Es werden die Punktlastlösungen im Frequenz-Wellenzahlbereich und durch Integration über die Wellenzahlen berechnet. Man erhält die Wellenfelder, die Terzspektren für verschiedene Entfernungen und Frequenzen. Es wird die Tiefenlage und das Bodenmodell (homogen, geschichtet und kontinuierlich zunehmende Steifigkeit) variiert. Die Rayleigh-Welle verliert ihre Bedeutung und stattdessen kann die Vollraumlösung zur Interpretation und Prognose verwendet werden. Es werden die Halbraumlösung mit und ohne Rayleigh-Welle und die Vollraumlösung in der Tiefe diskutiert und verglichen. Neben der Wellenausbreitung (der Transmission) werden auch Effekte der Erschütterungsanregung (der Emission) und der Übertragung in Gebäude (der Immission) mit Hilfe der Finite-Element-Randelement-Methode berechnet. Die Verteilung der dynamischen Achslast durch die Tunnelsohle ergibt eine Minderung gegenüber der Punktlastanregung. Bei der Immission hat man keine Freifeldanregung wie an der Bodenoberfläche. Man muss entweder neben der Wellenamplitude (Verschiebung oder Schwinggeschwindigkeit) in der Tiefe auch die Spannung der ankommenden Welle berücksichtigen, oder man muss die Freifeldamplituden nach Bodenaushub berechnen. Die Rechenergebnisse deuten darauf hin, dass man als Freifeldanregung die zweifache Vollraumlösung ansetzen kann.
Measurements at the foundation, the surrounding soil and nearby buildings have been done during several drop tests of different containers on different foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. It was controlled that the foundation does not absorb more than 2 percent of the energy of the container. Most of the drop energy is lost in shock absorbers. Later on, a smaller drop test facility has been built on the ground but inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which occur during the drop tests. On the other hand, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Different sensors, accelerometers, accelerometers with mechanical filters, geophones (velocity transducers), strain gauges, and pressure cells have been applied for these tasks. The signals have been transformed to displacements which proved to be best suited for the interpretation of the impact mechanism. Modell calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple estimation. The amplitudes of the foundation could also be estimated from the ground vibrations and their amplitude-distance law.