7.2 Ingenieurbau
Filtern
Dokumenttyp
- Vortrag (170)
- Beitrag zu einem Tagungsband (83)
- Zeitschriftenartikel (68)
- Posterpräsentation (10)
- Buchkapitel (4)
- Dissertation (4)
- Beitrag zu einem Sammelband (3)
- Sonstiges (2)
- Tagungsband (Herausgeberschaft für den kompletten Band) (1)
Sprache
- Englisch (260)
- Deutsch (84)
- Mehrsprachig (1)
Schlagworte
- Structural Health Monitoring (26)
- Ground vibration (20)
- Structural health monitoring (15)
- Fatigue (14)
- Brücken (11)
- Monitoring (11)
- Offshore (11)
- Offshore wind energy (11)
- Hammer impact (9)
- Impact (9)
- Train passage (9)
- Damage characterization (8)
- Model interpolation (8)
- Planar tomography (8)
- SHM (8)
- Structural systems (8)
- Vibration measurements (8)
- Building vibration (7)
- Damage detection (7)
- Deterioration (7)
- Layered soil (7)
- Reliability (7)
- Slab track (7)
- Soil-structure interaction (7)
- Train-induced ground vibration (7)
- Bahnerschütterungen (6)
- Compressive strength (6)
- Design methods (6)
- Grout (6)
- Inspection (6)
- Numerical modelling (6)
- Offshore wind turbines (6)
- Physical phenomenology (6)
- Pile foundations (6)
- Reinforced concrete structure (6)
- Datenmanagement (5)
- Environmental effects (5)
- Interface (5)
- Layered soils (5)
- Modalanalyse (5)
- Numeric simulation (5)
- Repair (5)
- Temperature rejection (5)
- Ultrasonic testing (5)
- Vibration (5)
- Windenergie (5)
- Bayesian updating (4)
- Container loading (4)
- Crack detection (4)
- Damage localization (4)
- Drop test (4)
- Erosion (4)
- Erschütterungen (4)
- Erschütterungsminderung (4)
- Excitation forces (4)
- Fault detection (4)
- Foundation load (4)
- Foundations (4)
- Gründungsstrukturen (4)
- High-strength concrete (4)
- Inspection planning (4)
- Mitigation (4)
- Offshore geomechanics (4)
- Probabilistic (4)
- Shell Buckling (4)
- Statistical tests (4)
- Steel structures (4)
- Subspace methods (4)
- Subspace-based method (4)
- Tunnel (4)
- Vehicle-track-soil interaction (4)
- Vibration measurement (4)
- Wind (4)
- Wind Energy (4)
- Ansys Autodyn (3)
- Attenuation (3)
- Axle impulses (3)
- BIM (3)
- Bauwerksüberwachung (3)
- Belastungsversuch (3)
- Box-Behnken (3)
- Bridge (3)
- Bridges (3)
- Brücke (3)
- Buckling (3)
- Compaction Grouting (3)
- Cracks (3)
- DUCON® (3)
- Deep foundations (3)
- Dispersionsmessung (3)
- Drucker-Prager (3)
- Ductility (3)
- E-modulus (3)
- Earth masonry (3)
- Elastische Gleiselemente (3)
- Emission (3)
- Erschütterungsprognose (3)
- Filter effects (3)
- Fly ash (3)
- Grouted connection (3)
- Grouting (3)
- Großer Fallturm Horstwalde (3)
- Irregular soil (3)
- Leichtbau (3)
- Linear parameter varying systems (3)
- Load vector (3)
- Maintenance (3)
- Material moisture (3)
- Metakaolin (3)
- Micro-reinforcement (3)
- Micromechanical modelling (3)
- Mobile elements (3)
- Model updating (3)
- Monopiles (3)
- Numerical modeling (3)
- Offshore Pile Foundation (3)
- Offshore Windenergieanlagen (3)
- Offshore foundations (3)
- Offshore wind turbine (3)
- Physical testing (3)
- Post-impact evaluation (3)
- Quasi-static and dynamic tests (3)
- Railway (3)
- Railway bridge (3)
- Randomly heterogeneous soil (3)
- Rehabilitation (3)
- Reinforced concrete (3)
- Risk (3)
- Scattering (3)
- Schwingungsdynamik (3)
- Soil erosion (3)
- Soil properties (3)
- Statistical evaluation (3)
- Statistical method (3)
- Stereo photogrammetry (3)
- Subspace-based residual (3)
- Temperature effects (3)
- Train speed (3)
- UHPC (3)
- Umwelteinflüsse (3)
- Vehicle-track interaction (3)
- Vibrations (3)
- Wellenausbreitung (3)
- Wellengeschwindigkeit (3)
- Zivile Sicherheit (3)
- 2-span bridge (2)
- AISTEC (2)
- Acceleration sensors (2)
- Achsfolgespektren (2)
- Acoustic emission testing (2)
- Amplitude-charge weight laws (2)
- Amplitude-distance laws (2)
- Analysis of variance (2)
- Apartment building (2)
- Artificial Intelligence (2)
- Artificial intelligence (2)
- Automatisierte schweißtechnische Fertigung (2)
- Axle sequence (2)
- Axle-sequence spectrum (2)
- Ballast track (2)
- Bauteile (2)
- Bauwerke (2)
- Bauwerksmonitoring (2)
- Bayes'sche Analyse (2)
- Bayesian System Identification (2)
- Bayesian analysis (2)
- Bayesian methods (2)
- Bayesian system identification (2)
- Bemessung (2)
- Big Data (2)
- Bitumen (2)
- Bodenübertragungsfunktion (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Changing process noise (2)
- Chemisoprtion (2)
- Climate chamber (2)
- Compressive Cyclic loading (2)
- Compressive cyclic loading (2)
- Computer Vision (2)
- Concrete (2)
- Coupled fluid-particle simulation (2)
- Coupler systems (2)
- Crack Luminescence (2)
- Crack formation (2)
- Crack pattern (2)
- Cyclic load (2)
- DEM (2)
- Damage identification (2)
- Design (2)
- Digital twin (2)
- Digitalisierung (2)
- Displacements (2)
- Drone (2)
- Earth block masonry (2)
- Elastische Elemente (2)
- Elastische Gebäudelagerung (2)
- Energy (2)
- Erschütterungsausbreitung (2)
- Evaluation (2)
- Explosion-induced ground vibrations (2)
- Faseroptik (2)
- Feuchte (2)
- Finite Elemente Simulation (2)
- Finite element models (2)
- Freight train (2)
- GPU parallel computation (2)
- Gaussian Process (2)
- Geotechnical site-characterization (2)
- Gleiströge (2)
- Ground vibration measurements (2)
- Grouted Connection (2)
- Halbraum (2)
- High-performance computing (2)
- High-speed (2)
- High-speed train (2)
- Immission (2)
- Injection Sequence (2)
- Irregular ballast (2)
- Irregularities (2)
- Jacket support structure (2)
- Jet erosion test (2)
- Klimakammer (2)
- Knudsen effect (2)
- LBM-DEM (2)
- Laboratory beam structure (2)
- Lehm (2)
- Long-term shrinkage (2)
- Luminescence (2)
- Macromechanical Sample Strength (2)
- Material tests (2)
- Mauerwerk (2)
- Measurement (2)
- Measurements (2)
- Messen im Bauwesen (2)
- Micro silica (2)
- Micromechanical Tensile Failure (2)
- Mix design (2)
- Modal Analysis (2)
- Moisture (2)
- Moisture content (2)
- Molecular diffusion (2)
- Non destructive testing (2)
- Non-Destructive Evaluation (2)
- Non-destructive testing (2)
- Numerical model (2)
- Office tower (2)
- Offshore Wind (2)
- Offshore Wind Energy (2)
- Offshore Windenergy Pile Buckling (2)
- Offshore geotechnics (2)
- Offshore wind (2)
- Offshore-Windenergieanlagen (2)
- Optimal Sensor Placement (2)
- Passenger train (2)
- Physisorption (2)
- Pile Foundation (2)
- Pile Tip Buckling (2)
- Prediction (2)
- Prediction of explosion induced ground and building vibration (2)
- Probability of Detection (2)
- Prädiktive Instandhaltung (2)
- Radar (2)
- Railway tunnel (2)
- Railways (2)
- Rechenmodelle (2)
- Reinforcement (2)
- Relative humidity (2)
- Repowering (2)
- Research data management (2)
- Residual evaluation (2)
- Resonance (2)
- Risslumineszenz (2)
- SDDLV (2)
- Safety (2)
- Scattered axle impulses (2)
- Schadensdetektion (2)
- Schwingungsbasierte Verfahren (2)
- Size effect (2)
- Slenderness effect (2)
- Soil-Structure-Interaction (2)
- Soil-pile interaction (2)
- Soil-wall-floor model (2)
- Static axle loads (2)
- Static load (2)
- Strength (2)
- Strukturmonitoring (2)
- Suction bucket (2)
- Supplementary cementitious materials (2)
- Surface-tunnel reduction (2)
- System Identification (2)
- System identification (2)
- Tensile Capacity (2)
- Time-variant reliability (2)
- Tomographic damage evaluation (2)
- Track damage (2)
- Track-soil interaction (2)
- Train excitation (2)
- Transmission (2)
- Uncertainty (2)
- Uncertainty in reference (2)
- Uncertainty quantification (2)
- Unterraummethoden (2)
- Value of Information (2)
- Vehicle–track interaction (2)
- Verkehrsinfrastukturen (2)
- Vollraum (2)
- Wellenausbreitung in der Tiefe (2)
- Wind Turbines (2)
- Wind energy (2)
- Wind turbine tower (2)
- Windenergieanlagen (2)
- Windenergy (2)
- Zuggeschwindigkeit (2)
- Zuverlässigkeit (2)
- 3D imaging (1)
- Achsimpulse (1)
- Acoustic emission (1)
- Acoustic emission analysis (1)
- Ambient excitation (1)
- Amplituden-Abstands-Gesetze (1)
- Analytical Design Methods (1)
- Asphalt (1)
- Assessment (1)
- Asymptotic local approach (1)
- Automated Modal Analysis for Tracking Structural Change during Construction and Operation Phases (1)
- Automated operational modal analysis (1)
- Automatic modal parameters identification (1)
- Automatisierte Fertigung (1)
- Automatisierte schweißtechniche Fertigung (1)
- Autonomous underwater vehicles (1)
- Axial load bearing (1)
- Axle loads (1)
- Axle pulses (1)
- BAM Windenergie Fügetechnik (1)
- Bahngleis (1)
- Base isolation (1)
- Baugrunddynamik (1)
- Bauwerk-Boden-Wechselwirkung (1)
- Bauwerksdiagnostik (1)
- Beanspruchungszustand (1)
- Belastungsfahrt (1)
- Belastungstest (1)
- Belastungszug (1)
- Benchmark (1)
- Beschleunigungssensoren (1)
- Beton (1)
- Betonautobahn (1)
- Betonautobahnen (1)
- Beulen (1)
- Bewertung (1)
- Bionik (1)
- Blast (1)
- Blast tests (1)
- Bodenschlitz (1)
- Bodenvariabilität (1)
- Boreholes (1)
- Boundary element (1)
- Boundary element method (1)
- Bridge monitoring (1)
- Bridge resonance (1)
- Bridge vibration (1)
- Bruchlastwechselzahlen (1)
- Brückensicherheit (1)
- Buckling piles circular shells (1)
- Buckling soil-structure-interaction offshore piles track (1)
- Building Information Modeling (1)
- Building and Construction (1)
- Building information modelling (1)
- Building response (1)
- Bulging (1)
- CFD (1)
- CPT (1)
- Cancellation (1)
- Cars (1)
- Cement-based composites (1)
- Cemented soil (1)
- Centerline solidification cracking (1)
- Chemisorption (1)
- Civil and Structural Engineering (1)
- Civil structures (1)
- Climate Chamber (1)
- Coating (1)
- Cohesive granular materials (1)
- Cohesive soils (1)
- Column/wall resonance (1)
- Combined finite-element boundary-element method (1)
- Compaction grouting (1)
- Compliance function (1)
- Components of excitation (1)
- Compression tests (1)
- Computational (1)
- Condensed Matter Physics (1)
- Conductor (1)
- Continuous soil (1)
- Continuously inhomogeneous geological media (1)
- Continuously inhomogeneous soils (1)
- Crack (1)
- Crack damage detection (1)
- Crack growth (1)
- Crack repair (1)
- Cyber security (1)
- Cyclic axial shearing (1)
- Cyclic degradation (1)
- DEM-LBM simulation (1)
- Damage Detection (1)
- Damage Identification (1)
- Damage evolution (1)
- Decision matrix analysis (1)
- Deckeneigenfrequenzen (1)
- Deckenschwingungen (1)
- Design models (1)
- Design practice (1)
- Detection (1)
- DiMoWind RDS-PP Maintenance Digital Twin Offshore Wind Energy (1)
- Digital Image Correlation (1)
- Digital Image Correlation (DIC) (1)
- Digital Models (1)
- Digital Twin (1)
- Digitale Zwillinge (1)
- Discrete Element Method (1)
- Discrete element method (1)
- Drop Test (1)
- Drop Tests (1)
- Drop tower (1)
- Druckfestigkeit (1)
- Druckschwellenversuch (1)
- Dynamic axle loads (1)
- Dynamic excitation (1)
- Dynamic loads (1)
- Dynamic soil properties (1)
- Dynamische Bodenkennwerte (1)
- Dynamische Bodensteifigkeit (1)
- Dämpfung (1)
- EERA Joint Program (1)
- Earth (1)
- Earth blocks (1)
- Earth material (1)
- Earthen hydraulic constructions (1)
- Earthen hydraulic infrastructures (1)
- Einflusslinie (1)
- Einflusslinien (1)
- Einfügungsdämmung (1)
- End-of-life decision making (1)
- Entscheidungsfindung (1)
- Environmental (1)
- Environmental Effects (1)
- Environmental and Operational Variability (1)
- Environmental changes (1)
- Environmental influence (1)
- Erhaltungsmanagement (1)
- Ermüdung (1)
- Ermüdungsprüfung (1)
- Ermüdungsschäden (1)
- Ermüdungsverhalten (1)
- Erneuerbare Energien (1)
- Erosion of cohesive soils (1)
- Erschütterungen im Fernfeld (1)
- Estimation (1)
- FEM (1)
- FEM analysis (1)
- Fahrzeug-Fahrweg-Boden-Wechselwirkung (1)
- Fallturm (1)
- Fatigue damage (1)
- Fatigue deterioration (1)
- Fatigue strength (1)
- Fault detectionchanging (1)
- Features (1)
- Fequency domain (1)
- Fiber optic sensing (1)
- Fibre optic sensors (1)
- Finite element (1)
- Finite element analysis (1)
- Finite element method (1)
- Finite element model updating (1)
- Finite elements (1)
- Finite-Elemente-Modellkalibrierung (1)
- Finite-element boundary-element method (1)
- Flexibility (1)
- Flexible car body (1)
- Flexible wheelset (1)
- Floor resonance (1)
- Floors (1)
- Fluid Dynamics (1)
- Fluid-structure interaction (1)
- Fluidized beds (1)
- Footbridge (1)
- Force reconstruction (1)
- Foundation Pile (1)
- Foundation reliability analysis (1)
- Freileitung (1)
- Frequency response function (1)
- GMNIA (1)
- GNSS (1)
- GPA (1)
- GPU Parallel computing (1)
- GPU parallelisation (1)
- Gebäudelagerung (1)
- Gebäudemodelle (1)
- Gebäudeschwingungen (1)
- Gekoppelte Fluid-Partikel Simulationen (1)
- General Materials Science (1)
- Geology (1)
- Geomechanics (1)
- Geomechanics of offshore foundations (1)
- Geometric vehicle and track irregularities (1)
- Geometrie (1)
- Global ambient vibrations (1)
- Granular Cohesive Materials (1)
- Granular Cohesive Materials, (1)
- Granular cohesion (1)
- Granular materials (1)
- Ground (1)
- Grout Injection (1)
- HAZID (1)
- HTLS (1)
- Hard impact (1)
- Harter Anprall an Stahlbetonstrukturen (1)
- High-Rise Building (1)
- High-rise building (1)
- High-rise buildings (1)
- Horizontal stress (1)
- Horizontal wind turbine (1)
- Hydraulic jet erosion (1)
- IEPE (1)
- Impact damage of reinforced concrete (1)
- Impact damage on reinforced concrete (1)
- Impact loading (1)
- Impakt (1)
- Impedanzmethode (1)
- Imperfektion (1)
- Impinging jet (1)
- Inclination angle (1)
- Inertial Interaction (1)
- Inertial interaction (1)
- Inhomogeneous soils (1)
- Innovative Messtechnik (1)
- Inspeciton (1)
- Inspektion (1)
- Instandhaltung (1)
- Interface model (1)
- Jet impingement (1)
- Kalibrierung (1)
- Kinematic Interaction (1)
- Kinematic interaction (1)
- Kraft auf den Boden (1)
- LBM-DEM coupling (1)
- LBM-DEM simulation (1)
- Laminar flow (1)
- Laminography (1)
- Large components (1)
- Laser beam welding (1)
- Lateral dynamic displacement (1)
- Lateral load bearing (1)
- Lattice Boltzmann Method (1)
- Lattice Boltzmann method (1)
- Leichtbauprinzipien (1)
- Lifetime Extension (1)
- Load Test (1)
- Load bearing behaviour (1)
- Load identification (1)
- Load tests (1)
- Load-bearing (1)
- Load-bearing behaviour (1)
- Local approaches (1)
- Long-span bridge (1)
- Low-frequency shaker (1)
- MEMS (1)
- Maintal Bridge Gemuenden (1)
- Maintalbrücke Gemünden (1)
- Maintenance Digital Twin Offshore Wind Energy (1)
- Marine geomechanics (1)
- Marine geotechnics (1)
- Maschinenbetrieb (1)
- Maschinenfundament (1)
- Material Point Method (1)
- Material Point Method (MPM) (1)
- Material model (1)
- Measurement campaigns (1)
- Mechanical challenges (1)
- Merkblatt (1)
- Messfahrt (1)
- Microfine Cement (1)
- Microfine cement (1)
- Micromechanical LBM-DEM simulation (1)
- Micromechanical analysis (1)
- Micromechanical simulation (1)
- Microsilica (1)
- Minderungsmaßnahmen (1)
- Mixed formulation (1)
- Modal analysis (1)
- Modal force spectrum (1)
- Modal load spectrum (1)
- Modal system identification (1)
- Model Building (1)
- Model Update (1)
- Model Updating (1)
- Model update (1)
- Modell-Update (1)
- Modellierung (1)
- Modes (1)
- Modes and waves (1)
- Modulus of elasticity (1)
- Monitoring-informed inspection and maintenance planning (1)
- Monopile (1)
- Monopile Buckling (1)
- Monopile installation risks (1)
- Movin load test (1)
- Multi-beam method (1)
- Multi-beam track model (1)
- Multiple impact (1)
- NDT (1)
- Nachgiebigkeiten (1)
- Nelson’s method (1)
- Normung (1)
- Numerical analysis (1)
- Numerical damage simulation (1)
- Numerical simulation (1)
- Numerical simulation of impact damage (1)
- Numerical simulations (1)
- Numerische Analysen (1)
- Obstacles (1)
- Offhore (1)
- Office building (1)
- Offshore Structures (1)
- Offshore Wind Energy Converter (1)
- Offshore Windenergie (1)
- Offshore pile foundation (1)
- Offshore pile foundations (1)
- Offshore steel structures (1)
- Offshore wind energy foundations (1)
- Offshore wind farm (1)
- Offshore wind farms (1)
- Offshore wind-turbine foundations (1)
- Offshore-Wind (1)
- Offshore-Windenergie (1)
- Offshore-Windkraftanlagen (1)
- Operational modal analysis (1)
- Optimal sensor placement (1)
- Optimierungsmethoden (1)
- Optimization techniques (1)
- Perfectly Matched Layer (PML) (1)
- Pfahlfußbeulen (1)
- Pfahlnachgiebigkeiten (1)
- Physisoprtion (1)
- Piaui state (1)
- Pile Buckling (1)
- Pile Capacity (1)
- Pile ageing (1)
- Pile bending stiffness (1)
- Pile foundation (1)
- Pile groups (1)
- Pile retrofit system (1)
- Pile-Tip-Buckling (1)
- Point Cloud (1)
- Predictive maintenance (1)
- Pressure (1)
- Probabilistic modelling (1)
- Probabilitische Ingenieurmodelle (1)
- Probability of detection (1)
- Probekörpergeometrien (1)
- Process noise (1)
- Prognose (1)
- Propagation from a tunnel (1)
- Quasi-static response; (1)
- Rail roughness (1)
- Railbridge (1)
- Railway induced vibration (1)
- Railway track (1)
- Railway tracks (1)
- Railway trafiic (1)
- Randelementmethode (1)
- Random dynamics and vibrations (1)
- Random stiffness variation (1)
- Rayleighwellendispersion (1)
- Rechenverfahren (1)
- Recovery experiments (1)
- Referenzbeispiel (1)
- Referenzkennzeichnungssystem (1)
- Remote sensing vibrometer (1)
- Residential building (1)
- Richtige Fahrzeugmasse (1)
- Richtlinie (1)
- Rigid vehicle model (1)
- Risiko (1)
- Risikoanalyse (1)
- Risk-based design (1)
- Risk-based maintenance planning (1)
- Rissprozes (1)
- Rissprozess (1)
- SHCC (1)
- SHM Environmental (1)
- SHM environmental bridges (1)
- Sandstone (1)
- Santa-marta (1)
- Scaling (1)
- Schadensüberwachung (1)
- Schallemission (1)
- Scherwellengeschwindigkeit (1)
- Schienenfahrweg (1)
- Schienenfahrwege (1)
- Schrauben (1)
- Schubmodul (1)
- Schwingungsmessungen (1)
- Schwingungsmonitoring (1)
- Schädigungsprozesse (1)
- Sensitivity vectors (1)
- Serra da cangalha (1)
- Shearing (1)
- Shell buckling (1)
- Shrinkage (1)
- Shrinkage Reducing Admixture (1)
- Sicherheit (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Simulation and experiment (1)
- Site-characterization (1)
- Soft impact (1)
- Soft track elements (1)
- Soil Struture Interaction (1)
- Soil classification (1)
- Soil forces (1)
- Soil stiffness (1)
- Soil-building interaction (1)
- Soil-building resonance (1)
- Soil-wall floor model (1)
- Soil-water-structure interaction (1)
- Sorption isotherm (1)
- Spannbeton (1)
- Spannstahlbruch (1)
- Spatially varying ground conditions (1)
- Spektralanalyse (1)
- Stability Buckling soil-structure-interaction piles offshore (1)
- Stabilität (1)
- State of stress (1)
- Static loading (1)
- Statistical correlations (1)
- Statistical pattern recognition (1)
- Statistische Auswertung (1)
- Statistische Korrelationen (1)
- Stiffness variation (1)
- Stochastic Subspace Damage Detection (1)
- Strain (1)
- Stress stiffening (1)
- Stress-strain relation (1)
- Stress–strain-relation (1)
- Structural Systems (1)
- Structural integrity (1)
- Structural integrity maintenance (1)
- Structural integrity management (1)
- Structural system identification (1)
- Störgrößen (1)
- Substructures (1)
- Suction Bucket (1)
- Superplasticizer (1)
- Supplementary Cementitious Materials (1)
- Support structures (1)
- Surface Foundation (1)
- Surface line (1)
- Sustainable binders (1)
- Switch (1)
- Systemidentifikation (1)
- TOP (1)
- TRC (1)
- Tagung (1)
- Temperature effect (1)
- Temperature effect rejection (1)
- Temperature modeling (1)
- Temperatureinflüsse (1)
- Tensile test (1)
- Test specification (1)
- Tip Buckling (1)
- Track and vehicle irregularities (1)
- Track beam (1)
- Track damage monitoring (1)
- Track damage quantification (1)
- Track deflection (1)
- Track displacements (1)
- Track filter (1)
- Track filtering (1)
- Track vibration (1)
- Tragfähigkeit (1)
- Tragstrukturen (1)
- Train configuration (1)
- Train passages (1)
- Train-induced vibration (1)
- Tran speed (1)
- Transfer fuction (1)
- Transfer function (1)
- Transverse butt weld (1)
- Trench (1)
- Truss structures (1)
- Tunnel line (1)
- Tunnel-pile transfer (1)
- Tunnel-to-surface reduction (1)
- Tunnelstrecke (1)
- Turnout (1)
- UAS (1)
- Un- certainty (1)
- Unbounded domain (1)
- Under-sleeper pads (1)
- Value of information (1)
- Variational Bayesian statistics (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Varying track stiffness (1)
- Vibration analysis (1)
- Vibration excitation (1)
- Vibration monitoring (1)
- Viscosity (1)
- Vorspannung (1)
- Wahrscheinlichkeit (1)
- Water Science and Technology (1)
- Water-structure interaction (1)
- Wave propagation (1)
- Wave-Tower interaction (1)
- Wavenumber domain (1)
- Wavenumber integrals (1)
- Wavenumber method (1)
- Waves (1)
- Weld imperfections (1)
- Welded (1)
- Wellenfeldberechnung (1)
- Wheelset (1)
- Wheelset accelerations (1)
- Wind Energy Structures (1)
- Wind energy tower (1)
- Wind turbines (1)
- Wind-farm aerodynamics (1)
- Windenergieanlage (1)
- Windfarm wake analysis (1)
- Workability (1)
- Zerstreute Achsimpulse (1)
- acceleration sensors (1)
- building information modelling (1)
- calibration (1)
- elastische Gebäudelagerungen (1)
- environmental influences (1)
- fachwerkartige Stahltragwerken (1)
- layered soil (1)
- risk, reliability, inspection planning, offshore wind turbines (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- temperature (1)
- transmission behavior (1)
- zerstreute Achslastimpulse (1)
- Übertragungsmatrizen (1)
- Übertragungsverhalten (1)
- Überwachung (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (345) (entfernen)
Paper des Monats
- ja (5)
Es wird eine gekoppelte Finite-Element-Randelementmethode zur Berechnung von Pfahlgrün-dungen in inhomogenen (geschichteten) Böden vorgestellt. Sie beruht auf den Greenschen Funktionen (Punktlastlösungen) für inhomogene Böden. Diese Lösungen können auch für die Wellenausbreitung in der Tiefe, zum Beispiel von einem Bahntunnel zu einem eingebetteten Gebäude, dem Kellergeschoss benutzt werden. Die Punktlastlösungen in der Tiefe werden mit der Halbraumlösung an der Bodenoberfläche und mit der Vollraumlösung verglichen und Gesetzmäßigkeiten für geschichtete Böden abgeleitet. Zu den Pfahlgründungen werden die Horizontalnachgiebigkeiten von Pfählen in geschichteten Böden dargestellt. Für den homogenen und den kontinuierlich steifer werdenden Boden werden Potenzgesetze für den Boden- und Pfahleinfluss aufgestellt. Der Vergleich mit dem Winkler-Modell der rein lokalen Bodenreaktion zeigt, dass die Winkler-Bettung in allen Fällen einen zu kleinen Bodeneinfluss ergibt.
Am Beispiel von mehreren Bauvorhaben wird untersucht, mit welchen Unsicherheiten bei der Anwendung von Korrelationen zwischen Sondierergebnissen und Scherwellengeschwindigkeit zur Beschreibung der dynamischen Bodeneigenschaften gerechnet werden muss. Die Auswertung von Korrelationen aus der Literatur zur Abschätzung der Scherwellengeschwindigkeit aus Drucksondierdaten zeigt, dass bei homogenen Sandböden die Verteilung der Scherwellengeschwindigkeit über die Tiefe sehr gut wiedergegeben werden kann. Die Korrelationen haben dabei die Tendenz, den tatsächlichen Wert zu überschätzen. In den vorliegenden Fällen haben sich Überschätzungen zwischen 20 % und 50 % ergeben. Mit zunehmendem Feinkornanteil werden die Unsicherheiten aus den Korrelationen jedoch größer.
Es wird eine gekoppelte Finite-Element-Randelementmethode zur Berechnung von Pfahlgrün-dungen in inhomogenen (geschichteten) Böden vorgestellt. Sie beruht auf den Greenschen Funktionen (Punktlastlösungen) für inhomogene Böden. Diese Lösungen können auch für die Wellenausbreitung in der Tiefe, zum Beispiel von einem Bahntunnel zu einem eingebetteten Gebäude, dem Kellergeschoss benutzt werden. Die Punktlastlösungen in der Tiefe werden mit der Halbraumlösung an der Bodenoberfläche und mit der Vollraumlösung verglichen und Gesetzmäßigkeiten für geschichtete Böden abgeleitet. Zu den Pfahlgründungen werden die Horizontalnachgiebigkeiten von Pfählen in geschichteten Böden dargestellt. Für den homoge-nen und den kontinuierlich steifer werdenden Boden werden Potenzgesetze für den Boden- und Pfahleinfluss aufgestellt. Der Vergleich mit dem Winkler-Modell der rein lokalen Boden-reaktion zeigt, dass die Winkler-Bettung in allen Fällen einen zu kleinen Bodeneinfluss ergibt.
Die moderne Gesellschaft in Deutschland und Europa profitiert von der hervorragenden baulichen Infrastruktur, die für uns viele Aspekte aus den Bereichen Mobilität, Energieversorgung, Transport, Umweltschutz, (Nah-)Erholung und Gefahrenabwehr zur Alltäglichkeit werden lassen und uns ein hohes Gefühl der technischen Sicherheit vermitteln. Viele der Annehmlichkeiten, wie beispielweise ein Hochgeschwindigkeitseisenbahnverkehrsnetz, zuverlässige Stromversorgung im europäischen Verbundsystem und ein immenser Personen-, Güter- und Warenverkehr auf der Straße, zu Wasser und in der Luft ist ohne eine leistungsfähige, resiliente und zuverlässige bauliche Infrastruktur undenkbar.
In this contribution, we consider two applications in which probabilistic approaches can potentially complement or enhance the design and assessment of offshore wind turbine foundations. First, we illustrate in a numerical example that probabilistic modelling can be helpful in dealing with chang-es in turbine locations during the planning phase of an offshore wind farm. In this case, spatial probabilistic modelling of the ground conditions enables (a) an inference of the soil properties at the modified turbine location from field data collected at different locations across an offshore wind farm site and (b) an optimisation of further site investigations. Second, we discuss the uncer-tainties and risks associated with the installation of large diameter monopiles in soils with hetero-geneities such as strong layers and/or embedded boulders. Subsequently, we present a concept for modelling, understanding, and managing these risks based on a probabilistic model of the subgrade conditions, monopile, and subgrade-pile-interaction.
Irregularities of the track are a main cause of train-induced ground vibration, and track maintenance is of great importance. Although geometric irregularities at the wheel-rail contact are widely used, other types of irregularities, such as stiffness irregularities, irregularities from different track positions and irregularities in the wave propagation, were analysed in the present study. The track behaviour was investigated by a multi-beam-on-soil model. This track model is coupled with a vehicle model to calculate the vehicle–track interaction. The track model was also used for the track filtering, which transfers a track support error to the equivalent rail irregularity or, conversely, the sharp axle pulse on the rail to a smoother pulse on the soil. In the case in which this filtering varies randomly along the track, the pulses of the moving static load induce a certain ground Vibration component (“the scatter of axle pulses”). This effect was calculated by the superposition of axle pulses in the frequency domain and by a stochastic simulation. Simultaneous vehicle, track and soil measurements at a certain site were used to evaluate the different excitation and ground Vibration components. The agreement between calculations and axle-box and soil measurements is good. The ground vibrations calculated from rail irregularities and corresponding dynamic loads, however, clearly underestimate the measured ground vibration amplitudes. Only the static load that is moving over a varying track support stiffness can produce the important mid-frequency ground Vibration component by the scatter of axle pulses.
The fatigue process of concrete under compressive cyclic loading is still not completely explored. The corresponding damage processes within the material structure are especially not entirely investigated. The application of acoustic measurement methods enables a better insight into the processes of the fatigue in concrete. Normal strength concrete was investigated under compressive cyclic loading with regard to the fatigue process by using acoustic methods in combination with other nondestructive measurement methods. Acoustic emission and ultrasonic signal measurements were applied together with measurements of strains, elastic modulus, and static strength. It was possible to determine the anisotropic character of the fatigue damage caused by uniaxial loading based on the ultrasonic measurements. Furthermore, it was observed that the fatigue damage seems to consist not exclusively of load parallel oriented crack structures. Rather, crack structures perpendicular to the load as well as local compacting are likely components of the fatigue damage. Additionally, the ultrasonic velocity appears to be a good indicator for fatigue damage beside the elastic modulus. It can be concluded that acoustic methods allow an observation of the fatigue process in concrete and a better understanding, especially in combination with further measurement methods.
Gradual or sudden changes in the state of structural systems caused, for example, by deterioration or accidental load events can influence their load-bearing capacity. Structural changes can be inferred from static and/or dynamic response data measured by structural health monitoring systems. However, they may be masked by variations in the structural response due to varying environmental conditions. Particularly, the interaction of nominally load-bearing components with nominally non-load bearing components exhibiting characteristics that vary as a function of the environmental conditions can significantly affect the monitored structural response. Ignoring these effects may hamper an inference of structural changes from the monitoring data. To address this issue, we adopt a probabilistic model-based framework as a basis for developing digital twins of structural systems that enable a prediction of the structural behavior under varying ambient condition. Within this framework, different types of data obtained from real the structural system can be applied to update the digital twin of the structural system using Bayesian methods and thus enhance predictions of the structural behavior. In this contribution, we implement the framework to develop a digital twin of a simply supported steel beam with an asphalt layer. It is formulated such that it can predict the static response of the beam in function of its temperature. In a climate chamber, the beam was subject to varying temperatures and its static response wass monitored. In addition, tests are performed to determine the temperature-dependent properties of the asphalt material. Bayesian system identification is applied to enhance the predictive capabilities of the digital twin based on the observed data.
Gradual or sudden changes in the state of structural systems caused, for example, by deterioration or accidental load
events can influence their load-bearing capacity. Structural changes can be inferred from static and/or dynamic response data
measured by structural health monitoring systems. However, they may be masked by variations in the structural response due to
varying environmental conditions. Particularly, the interaction of nominally load-bearing components with nominally non-load
bearing components exhibiting characteristics that vary as a function of the environmental conditions can significantly affect the
monitored structural response. Ignoring these effects may hamper an inference of structural changes from the monitoring data. To
address this issue, we adopt a probabilistic model-based framework as a basis for developing digital twins of structural systems
that enable a prediction of the structural behavior under varying ambient condition. Within this framework, different types of data
obtained from real the structural system can be applied to update the digital twin of the structural system using Bayesian methods
and thus enhance predictions of the structural behavior. In this contribution, we implement the framework to develop a digital
twin of a simply supported steel beam with an asphalt layer. It is formulated such that it can predict the static response of the beam
in function of its temperature. In a climate chamber, the beam was subject to varying temperatures and its static response wass
monitored. In addition, tests are performed to determine the temperature-dependent properties of the asphalt material. Bayesian
system identification is applied to enhance the predictive capabilities of the digital twin based on the observed data.
In this article, the passage of different trains over different bridges will be studied for resonant excitation. The intensity of the resonance will be estimated in frequency domain by using three separated spectra. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of the train. The influences of train speed, bridge length, bridge support, track irregularities, and train type on the resonance amplitudes will be analysed for each of these spectra separately for getting a better insight. A variety of axle-sequence spectra and corresponding rules will be presented for different vehicles and trains. As examples, the passage of a slow freight train over a long-span bridge, a normal passenger train over a medium-span bridge, and a high-speed train over a short bridge will be analysed. Corresponding measurements show the amplification, but also the cancellation of the subsequent axle responses. Namely in one of the measurement examples, the first mode of the bridge was amplified and the second mode was cancelled at a low speed of the train and vice versa at a higher speed.
In this presentation, a framework for integrating vibration-based structural health monitoring data into the optimization of inspection and maintenance of deteriorating structural systems is presented. The framework is demonstrated in an illustrative example considering a steel frame subject to fatigue.
In this presentation, we discuss the potential of probabilistic approaches to the design and assessment of offshore foundations. The potential is demonstrated in a numerical example considering a laterally loaded monopile. As an outlook, we present a concept for managing the risk associated with installing large monopiles.
This article presents a solid cohesion model for the simulation of bonded granular assemblies in the frame of 3D discrete element approaches (DEM). A simple viscoplastic cohesion model for 2D geometries is extended to 3D conditions, while its yield criterion is generalized as a hyper-surface in the space of bond solicitations to include torsional moments. The model is then calibrated using experimental results of uniaxial traction at both the microscopic and macroscopic scales with an artificial granular cohesive soil. The paper finally presents some simulated results on the macromechanical sample traction application and briefly discusses the model's current limitations and promising prospects for subsequent works.
This article presents a solid cohesion model for the simulation of bonded granular assemblies in the frame of 3D discrete element approaches (DEM). A simple viscoplastic cohesion model for 2D geometries is extended to 3D conditions, while its yield criterion is generalized as a hyper-surface in the space of bond solicitations to include torsional moments. The model is then calibrated using experimental results of uniaxial traction at both the microscopic and macroscopic scales with an artificial granular cohesive soil. The paper finally presents some simulated results on the macromechanical sample traction application and briefly discusses the model's current limitations and promising prospects for subsequent works.
Prediction of building noise and vibration – 3D finite element and 1D wave propagation models
(2021)
Construction work or traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for the inhabitants. The transfer of the vibration from the free field to the building has been calculated by the finite element method for many models in consultancy and research work. The analysis for all storeys of certain building points such as walls, columns and floors unveiled some rules, some typical modes, and some wavetype responses. A simplified building-soil model has been created, which includes well these effects of building-soil resonance, wall/column resonance, floor resonances, and the high-frequency reduction. The model consists of one wall for a wall-type apartment building or a column for each specific part (mid, side or corner) of a column-type office building. The building response in the high-frequency (acoustic) region is calculated as mean values over all storeys and over wider frequency bands, by wave-type asymptotes of an infinitely tall building, and by the soil to wall ratio of impedances. The secondary noise is predicted by Transfer values between the building vibration (center of floors, walls at a room corner) and the sound pressure.
Prediction of building noise and vibration – 3D finite element and 1D wave propagation models
(2021)
Construction work or traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for the inhabitants. The transfer of the vibration from the free field to the building has been calculated by the finite element method for many models in consultancy and research work. The analysis for all storeys of certain building points such as walls, columns and floors unveiled some rules, some typical modes, and some wavetype responses. A simplified building-soil model has been created, which includes well these effects of building-soil resonance, wall/column resonance, floor resonances, and the high-frequency reduction. The model consists of one wall for a wall-type apartment building or a column for each specific part (mid, side or corner) of a column-type office building. The building response in the high-frequency (acoustic) region is calculated as mean values over all storeys and over wider frequency bands, by wave-type asymptotes of an infinitely tall building, and by the soil to wall ratio of impedances. The secondary noise is predicted by Transfer values between the building vibration (center of floors, walls at a room corner) and the sound pressure.
Die Linienlastgesetzmäßigkeit gilt nicht für Zuganregung. Die Punktlastgesetzmäßigkeit wird bei kurzen Zügen in größeren Entfernungen erreicht. Bei langen Zügen reduziert sich die Abnahme um r-0,3 für die theoretische exponentielle Dämpfungsabnahme, um r-0,5 für die vereinfachte potentielle Dämpfungsabnahme. Die gemessenen Abnahmereduktionen liegen in diesem Bereich.
Erschütterungen, die durch Eisenbahnverkehr erzeugt werden, breiten sich durch den Erdboden aus und regen benachbarte Gebäude zu Schwingungen an. Es wurde ein Prognoseverfahren für Bahnerschütterungen ent-wickelt, das mit einfachen Modellen schnell Ergebnisse liefert. Dies sind physikalische Modelle, zum Beispiel 1-dimensionale Modelle mit Übertragungsmatrizen für die Fahrzeug-Fahrweg-Boden-Wechselwirkung und für die Gebäude-Boden Wechselwirkung. Damit werden die komplexen Verhältnisse bei der Emission (dem Zusammen¬wirken von Fahrzeug und Fahrweg), bei der Transmission durch den homogenen oder geschichteten Boden und bei der Immission in Gebäuden näherungsweise erfasst. In (Auersch, 2020) wird gezeigt, dass diese einfachen Prognosemodelle die Ergebnisse von detaillierten Modellen wie der Finite-Element-Randelement-Methode für das Gleis, die Wellenzahlintegrale für den Boden und 3-dimensionale Finite-Element-Modelle für das Gebäude gut wiedergeben können. Dies entspricht auch der Absicht, die Prognosemodelle aus den Ergebnissen der Detailmodelle abzuleiten. Die drei Prognoseteile werden getrennt berechnet, aber es werden physikalisch sinn¬volle Schnittstellen verwendet. Für die Emission und Transmission sind es die auf den Untergrund wirkenden Erregerkräfte von Fahrzeug und Fahrweg, für die Transmission und Immission sind es die Freifeldamplituden des Bodens.
Erschütterungen, die durch Eisenbahnverkehr erzeugt werden, breiten sich durch den Erdboden aus und regen benachbarte Gebäude zu Schwingungen an. Es wurde ein Prognoseverfahren für Bahnerschütterungen ent-wickelt, das mit einfachen Modellen schnell Ergebnisse liefert. Dies sind physikalische Modelle, zum Beispiel 1-dimensionale Modelle mit Übertragungsmatrizen für die Fahrzeug-Fahrweg-Boden-Wechselwirkung und für die Gebäude-Boden Wechselwirkung. Damit werden die komplexen Verhältnisse bei der Emission (dem Zusammen¬wirken von Fahrzeug und Fahrweg), bei der Transmission durch den homogenen oder geschichteten Boden und bei der Immission in Gebäuden näherungsweise erfasst. In (Auersch, 2020) wird gezeigt, dass diese einfachen Prognosemodelle die Ergebnisse von detaillierten Modellen wie der Finite-Element-Randelement-Methode für das Gleis, die Wellenzahlintegrale für den Boden und 3-dimensionale Finite-Element-Modelle für das Gebäude gut wiedergeben können. Dies entspricht auch der Absicht, die Prognosemodelle aus den Ergebnissen der Detailmodelle abzuleiten. Die drei Prognoseteile werden getrennt berechnet, aber es werden physikalisch sinn¬volle Schnittstellen verwendet. Für die Emission und Transmission sind es die auf den Untergrund wirkenden Erregerkräfte von Fahrzeug und Fahrweg, für die Transmission und Immission sind es die Freifeldamplituden des Bodens.
Measurements at the foundation, the surrounding soil and nearby buildings have been done during several drop tests of different containers on different foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. It was controlled that the foundation does not absorb more than 2 percent of the energy of the container. Most of the drop energy is lost in shock absorbers. Later on, a smaller drop test facility has been built on the ground but inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which occur during the drop tests. On the other hand, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Different sensors, accelerometers, accelerometers with mechanical filters, geophones (velocity transducers), strain gauges, and pressure cells have been applied for these tasks. The signals have been transformed to displacements which proved to be best suited for the interpretation of the impact mechanism. Modell calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple estimation. The amplitudes of the foundation could also be estimated from the ground vibrations and their amplitude-distance law.
Zur Erschütterungsausbreitung an oberirdischen Bahnlinien gibt es gute Übereinstimmungen zwischen Messungen und der Theorie geschichteter Böden. Bei der Interpretation der Ergebnisse spielt die Rayleigh-Welle eine große Rolle. Je nach Frequenz und Wellenlänge hat die Rayleigh-Welle eine bestimmte Eindringtiefe und erreicht damit mehr oder weniger steife Bodenschichten. Damit bekommt man eine frequenzabhängige Bodensteifigkeit für die Erschütterungsprognose. Für die Wellenausbreitung in der Tiefe statt an der Bodenoberfläche müssen eigene Gesetzmäßigkeiten gefunden werden. Es werden die Punktlastlösungen im Frequenz-Wellenzahlbereich und durch Integration über die Wellenzahlen berechnet. Man erhält die Wellenfelder, die Terzspektren für verschiedene Entfernungen und Frequenzen. Es wird die Tiefenlage und das Bodenmodell (homogen, geschichtet und kontinuierlich zunehmende Steifigkeit) variiert. Die Rayleigh-Welle verliert ihre Bedeutung und stattdessen kann die Vollraumlösung zur Interpretation und Prognose verwendet werden. Es werden die Halbraumlösung mit und ohne Rayleigh-Welle und die Vollraumlösung in der Tiefe diskutiert und verglichen. Neben der Wellenausbreitung (der Transmission) werden auch Effekte der Erschütterungsanregung (der Emission) und der Übertragung in Gebäude (der Immission) mit Hilfe der Finite-Element-Randelement-Methode berechnet. Die Verteilung der dynamischen Achslast durch die Tunnelsohle ergibt eine Minderung gegenüber der Punktlastanregung. Bei der Immission hat man keine Freifeldanregung wie an der Bodenoberfläche. Man muss entweder neben der Wellenamplitude (Verschiebung oder Schwinggeschwindigkeit) in der Tiefe auch die Spannung der ankommenden Welle berücksichtigen, oder man muss die Freifeldamplituden nach Bodenaushub berechnen. Die Rechenergebnisse deuten darauf hin, dass man als Freifeldanregung die zweifache Vollraumlösung ansetzen kann.
Die Bemessung von tragendem Lehmmauerwerk erfolgt in Deutschland auf Basis der Lehmbau Regeln. Das dort verankerte Nachweisverfahren beruht auf einem globalen Sicherheitskonzept, welches aus zuverlässigkeitstheoretischer Sicht nicht mehr dem Stand der Technik entspricht. Auf Grund dessen wird das Bemessungskonzept für Lehmmauerwerk vom Deutschen Institut für Bautechnik (DIBt) voraussichtlich 2023 außer Kraft gesetzt. Ein statischer Nachweis von tragenden Lehmbauten wäre in Deutschland dann ausschließlich mit einer Zustimmung im Einzelfall (ZiE) oder vorhabenbezogener Bauartgenehmigung (vBg) möglich. Beides ist mit erheblichem Mehraufwand und höheren Kosten verbunden, was für den Lehmmauerwerksbau einen entscheidenden Nachteil im Vergleich zum konventionellen Mauerwerksbau darstellt. Um eine unkomplizierte Praxisanwendung von Lehmmauerwerk zu ermöglichen, werden innerhalb eines Forschungsvorhabens, welches von der Bundesanstalt für Materialforschung und -prüfung (BAM), dem Institut für Massivbau der Technischen Universität Darmstadt sowie dem Ingenieurbüro ZRS durchgeführt wird, auf Basis der Produktnormen für Lehmsteine und Lehmmauermörtel Grundlagen für ein aktualisiertes Bemessungskonzept entwickelt. Im Rahmen des Projekts wird ebenfalls untersucht, inwiefern die Bemessungsregeln nach den vereinfachten Berechnungsmethoden für unbewehrtes Mauerwerk gemäß DIN EN 1996-3 / NA auf den Lehmmauerwerksbau übertragbar sind. Falls eine Anwendung des normativen Nachweisverfahrens bei Lehmmauerwerk möglich ist, wäre zukünftig eine Aufnahme von Lehmsteinen und Lehmmauermörtel in den nationalen Anhang des Eurocode 6 denkbar, was eine bedeutsame Erweiterung des Anwendungsbereichs von Lehmmauerwerk zur Folge hätte.
Diverse wissenschaftliche Untersuchungen konnten zeigen, dass bemessungsrelevante Festigkeits- und Verformungseigenschaften von Lehmmauerwerksbaustoffen stark von der vorherrschenden Materialfeuchte abhängen, welche im hygroskopischen Wassergehaltsbereich im Wesentlichen von der relativen Luftfeuchte (RLF) bestimmt wird. Auch die Zwischenergebnisse des laufenden Forschungsvorhabens zur Entwicklung eines Bemessungskonzepts für Lehmmauerwerk ergaben eine deutlich erkennbare Abhängigkeit zwischen der Materialfeuchte und den relevanten Festigkeits- und Verformungseigenschaften. Eine detaillierte Kenntnis des feuchteabhängigen Materialverhaltens von Lehmsteinen, -mörtel und -mauerwerk ist zwingend erforderlich, um ein konsistentes und zuverlässiges Bemessungskonzept für Lehmmauerwerk zu entwickeln. Im Rahmen des laufenden Forschungsprojektes werden deshalb umfangreiche Versuche zum Drucktragverhalten von Lehmsteinen und -mörtel sowie Lehmmauerwerk nach Konditionierung bei unterschiedlichen RLF durchgeführt und analysiert. Weiterhin werden auf Basis der experimentellen Ergebnisse numerische Modelle kalibriert, welche die detaillierte Analyse der Biegedrucktragfähigkeit von Lehmmauerwerk ermöglichen.
In diesem Beitrag werden zunächst die bisherigen Zwischenergebnisse bezüglich der experimentell ermittelten feuchteabhängigen Materialkennwerte von Lehmsteinen, -mörtel und -mauerwerk dargelegt. Darauf aufbauend werden numerische Untersuchungen zur Bestimmung der Systemtragfähigkeit von Lehmmauerwerk unter Feuchteeinflusses durchgeführt und erläutert.
Measurements at the foundation, the surrounding soil and nearby buildings have been done during several drop tests of different containers on different foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. It was controlled that the foundation does not absorb more than 2 percent of the energy of the container. Most of the drop energy is lost in shock absorbers. Later on, a smaller drop test facility has been built on the ground but inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which occur during the drop tests. On the other hand, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Different sensors, accelerometers, accelerometers with mechanical filters, geophones (velocity transducers), strain gauges, and pressure cells have been applied for these tasks. The signals have been transformed to displacements which proved to be best suited for the interpretation of the impact mechanism. Modell calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple estimation. The amplitudes of the foundation could also be estimated from the ground vibrations and their amplitude-distance law.
Zur Erschütterungsausbreitung an oberirdischen Bahnlinien gibt es gute Übereinstimmungen zwischen Messungen und der Theorie geschichteter Böden. Bei der Interpretation der Ergebnisse spielt die Rayleigh-Welle eine große Rolle. Je nach Frequenz und Wellenlänge hat die Rayleigh-Welle eine bestimmte Eindringtiefe und erreicht damit mehr oder weniger steife Bodenschichten. Damit bekommt man eine frequenzabhängige Bodensteifigkeit für die Erschütterungsprognose. Für die Wellenausbreitung in der Tiefe statt an der Bodenoberfläche müssen eigene Gesetzmäßigkeiten gefunden werden. Es werden die Punktlastlösungen im Frequenz-Wellenzahlbereich und durch Integration über die Wellenzahlen berechnet. Man erhält die Wellenfelder, die Terzspektren für verschiedene Entfernungen und Frequenzen. Es wird die Tiefenlage und das Bodenmodell (homogen, geschichtet und kontinuierlich zunehmende Steifigkeit) variiert. Die Rayleigh-Welle verliert ihre Bedeutung und stattdessen kann die Vollraumlösung zur Interpretation und Prognose verwendet werden. Es werden die Halbraumlösung mit und ohne Rayleigh-Welle und die Vollraumlösung in der Tiefe diskutiert und verglichen. Neben der Wellenausbreitung (der Transmission) werden auch Effekte der Erschütterungsanregung (der Emission) und der Übertragung in Gebäude (der Immission) mit Hilfe der Finite-Element-Randelement-Methode berechnet. Die Verteilung der dynamischen Achslast durch die Tunnelsohle ergibt eine Minderung gegenüber der Punktlastanregung. Bei der Immission hat man keine Freifeldanregung wie an der Bodenoberfläche. Man muss entweder neben der Wellenamplitude (Verschiebung oder Schwinggeschwindigkeit) in der Tiefe auch die Spannung der ankommenden Welle berücksichtigen, oder man muss die Freifeldamplituden nach Bodenaushub berechnen. Die Rechenergebnisse deuten darauf hin, dass man als Freifeldanregung die zweifache Vollraumlösung ansetzen kann.
Structural health monitoring (SHM) of civil structures often is limited due to changing environmental conditions, as those changes affect the structural dynamical properties in a similar way like damages can do. In this article, an approach for damage detection under changing temperatures is presentedand applied to a beam structure. The used stochastic subspace-based algorithm relies on a reference null space estimate, which is confronted to data from the testing state in a residual function. For damage detection the residual is evaluated by means of statistical hypothesis tests. Changes of the system due to temperature effects are handled with a model interpolation approach from linear parameter varying system theory. From vibration data measured in the undamaged state at some few reference temperatures, a model of the dynamic system valid for the current testing temperature is interpolated. The reference null space and the covariance matrix for the hypothesis test is computed from this interpolated model. This approach has been developed recently and was validated in an academic test case on simulations of a mass-spring-damper. In this paper, the approach is validated experimentally on a beam structure under varying temperature conditions in a climate chamber. Compared to other approaches, the interpolation approach leads to significantly less false positive alarms in the reference state when the structure is exposed to different temperatures, while faults can still be detected reliably.
The statistical subspace-based damage detection technique has shown promising theoretical and practical results for vibration-based structural health monitoring. It evaluates a subspacebased residual function with efficient hypothesis testing tools, and has the ability of detecting small changes in chosen system parameters. In the residual function, a Hankel matrix of Output covariances estimated from test data is confronted to its left null space associated to a reference model. The hypothesis test takes into account the covariance of the residual for decision making. Ideally, the reference model is assumed to be perfectly known without any uncertainty, which is not a realistic assumption. In practice, the left null space is usually estimated from a reference data set to avoid model errors in the residual computation. Then, the associated uncertainties may be non-negligible, in particular when the available reference data is of limited length. In this paper, it is investigated how the statistical distribution of the residual is affected when the reference null space is estimated. The asymptotic residual distribution is derived, where its refined covariance term considers also the uncertainty related to the reference null space estimate. The associated damage detection test closes a theoretical gap for real-world applications and leads to increased robustness of the method in practice. The importance of including the estimation uncertainty of the reference null space is shown in a numerical study
and on experimental data of a progressively damaged steel frame.
Structural health monitoring (SHM) of civil structures often is limited due to changing environmental conditions, as those changes affect the structural dynamical properties in a similar way like damages can do. In this article, an approach for damage detection under changing temperatures is presentedand applied to a beam structure. The used stochastic subspace-based algorithm relies on a reference null space estimate, which is confronted to data from the testing state in a residual function. For damage detection the residual is evaluated by means of statistical hypothesis tests. Changes of the system due to temperature effects are handled with a model interpolation approach from linear parameter varying system theory. From vibration data measured in the undamaged state at some few reference temperatures, a model of the dynamic system valid for the current testing temperature is interpolated. The reference null space and the covariance matrix for the hypothesis test is computed from this interpolated model. This approach has been developed recently and was validated in an academic test case on simulations of a mass-spring-damper. In this paper, the approach is validated experimentally on a beam structure under varying temperature conditions in a climate chamber. Compared to other approaches, the interpolation approach leads to significantly less false positive alarms in the reference state when the structure is exposed to different temperatures, while faults can still be detected reliably
Im AISTEC Projekt erforscht der FB 7.2 Verfahren zur Bewertung von Verkehrsbrücken auf der Gruandlage von sensorbasierten Bauwerksmessungen. In diesem Vortrag wird ein Überlick über die Forschungsarbeiten des FB 7.2 präsentiert. Des Weiteren wird ein Ausblick zur quantitativen Integration von sensorbasierten Bauwerksmessungen in die risiko-basierte prädiktive Planung von Inspektionen und Reparaturen von Ingenieurbauwerken gegeben.
Der Vortrag stellt die Durchführung und die ersten Ergebnisse der Belastungsfahrten der BAM im Rahmen des AISTEC Projekts an der Maintalbrücke am 19.05. und 20.05.2021 vor. Es wurden Tragwerksreaktionen des Bauwerks mit dem installierten Dauermonitoringsystem und insbesondere dem Betongelenk mit zusätzlich installierter Sensorik aufgezeichnet. Für die Ermittlung der Lastposition wurden mehrere Verfahren eingesetzt und verglichen.
Changes in the measured response of structural systems can be an indication of structural damages. However, such changes can also be caused by the effect of varying environmental conditions. To detect, localize and quantify changes or damages in structural systems subject to varying environmental conditions, physics-based models of the structural systems have to be applied which explicitly account for the influence of ambient conditions on the structural behavior. Data obtained from the structural systems should be used to calibrate the models and update predictions. Bayesian system identification is an effective framework for this task. In this paper, we apply this framework to learn the parameters of two competing structural models of a reinforced concrete beam subject to varying temperatures based on static response data. The models describe the behavior of the beam in the uncracked and cracked condition. The data is collected in a series of load tests in a climate chamber. Bayesian model class selection is then applied to infer the most plausible condition of the beam conditional on the available data.
Nach den bisherigen Regeln werden Bauwerksprüfungen von Brücken in starr definierten Intervallen durchgeführt. Diese starre, periodische, zustandsbasierte Instandhaltungsstrategie soll zukünftig durch eine flexible und prädiktive Instandhaltung ersetzt werden. Hierbei sollen Inspektionen und Instandhaltungsmaßnahmen unterstützt durch autonome Systeme auf der Grundlage von Monitoringdaten geplant und zusätzlich bei unvorhergesehenen Ereignissen ausgelöst werden. Im Rahmen des Verbundforschungsvorhabens AISTEC wird ein Vorgehen für Großbauwerke und kleinere Regelbauwerke zur Umsetzung eines kombinierten globalen, schwingungsbasierten und quasistatischen Monitorings entworfen. An der Maintalbrücke Gemünden – einer semiintegralen Rahmenbrücke aus Spannbeton auf der Schnellfahrstrecke Hannover–Würzburg – wurde als Demonstrator ein Dauermonitoring realisiert.
Changes in the measured response of structural systems can be an indication of structural damages. However, such changes can also be caused by the effect of varying environmental conditions. To detect, localize and quantify changes or damages in structural systems subject to varying environmental conditions, physics-based models of the structural systems have to be applied which explicitly account for the influence of ambient conditions on the structural behavior. Data obtained from the structural systems should be used to calibrate the models and update predictions. Bayesian system identification is an effective framework for this task. In this paper, we apply this framework to learn the parameters of two competing structural models of a reinforced concrete beam subject to varying temperatures based on static response data. The models describe the behavior of the beam in the uncracked and cracked condition. The data is collected in a series of load tests in a climate chamber. Bayesian model class selection is then applied to infer the most plausible condition of the beam conditional on the available data.
The reliability of deteriorating structures at time t is quantified by the probability that failure occurs within the period leading up to time t. This probability is often referred to as cumulative failure probability and is equal to the cumulative distribution function of the time to failure. In structural reliability, an estimate of the cumulative failure probability is obtained based on probabilistic engineering models of the deterioration processes and structural performance. Information on the condition and the loading contained in inspection and monitoring data can be included in the probability estimate through Bayesian updating. Conditioning the probability of failure on the inspection or monitoring outcomes available at time t (e.g. detections or no detection of damages) can lead to a reduction in that probability.
Such a drop in the cumulative failure probability might seem counterintuitive since the cumulative failure probability is a non-decreasing function of time. In this paper, we illustrate—with the help of a numerical example—that such a drop is possible because the cumulative probability before and after the updating is not based on the same information, hence not on the same probabilistic model.
The reliability of deteriorating structures at time t is quantified by the probability that failure occurs within the period leading up to time t. This probability is often referred to as cumulative failure probability and is equal to the cumulative distribution function of the time to failure. In structural reliability, an estimate of the cumulative failure probability is obtained based on probabilistic Engineering models of the deterioration processes and structural performance. Information on the condition and the loading contained in inspection and monitoring data can be included in the probability estimate through Bayesian updating. Conditioning the
probability of failure on the inspection or monitoring outcomes available at time t (e.g. detections or no detection of damages) can lead to a reduction in that probability.
Such a drop in the cumulative failure probability might seem counterintuitive since the cumulative failure probability is a non-decreasing function of time. In this paper, we illustrate—with the help of a numerical example—that such a drop is possible because the cumulative probability before and after the updating is not based on the same information, hence not on the same probabilistic model.
Fatigue is one of the main deterioration processes affecting the performance of welded steel support structures of wind turbines in offshore wind farms. In this contribution, we present a probabilistic physics-based fatigue deterioration model of a wind farm that accounts for the stochastic dependence among the fatigue behavior of different hotspots at turbine and wind farm level. The dependence exists because of uncertain common influencing factors such as similar material properties, fabrication qualities and load conditions. These system effects signify that an inspection of one hotspot provides indirect information of the condition of the remaining hotspots and thus enable an optimization of the inspection effort for a wind farm.
The wind farm model consists of two levels: A turbine support structure (level 1 system model) is represented by its fatigue hotspots and their stochastic dependence. The fatigue performance of a hotspot is described by a probabilistic fracture mechanics (FM) fatigue model. The probabilistic model of the parameters of the FM fatigue model is calibrated based on design data and is thus directly linked to the design of the turbine support structures. Dependence among the fatigue performances of different hotspots in a turbine support structure is modeled by introducing correlations between the stochastic parameters of the FM fatigue models. A wind farm (level 2 system model) consists of different turbine support structures (level 1 system models). Additional correlations are introduced at wind farm level to account for the dependence among the fatigue behavior of hotspots belonging to different turbine support structures. The wind farm model enables the computation of (marginal) hotspot fatigue reliabilities, system fatigue reliabilities of individual turbine support structures and the system fatigue reliability of an entire wind farm. The probabilistic model of the parameters of the two-level system model can be consistently updated with inspection outcomes using Bayesian methods. The updated probabilistic model of the model parameters then forms the basis for updating the estimates of the fatigue reliabilities.
We implement the wind farm model in a software tool named SysPark. The tool provides the means for planning inspections at wind farm level using an adaptive reliability-based threshold approach. In this approach, the first inspection campaign is planned in the year before the fatigue failure rates of the hotspots with the lowest fatigue reliabilities exceed a threshold failure rate. Once inspection results become available, the probabilistic model of the parameters of the wind farm model is updated. If repairs are performed, the wind farm model is additionally modified to describe the behavior of the repaired hotspots. The updated and modified model then enables the planning of the next inspection campaign and so on. The software tool is demonstrated in a case study considering a generic wind farm consisting of turbines with jacket support structures.
There is a strong need for cost-effective mitigation measures for
turnouts. SBB has initiated a series of examinations using different methodologies to gain a deeper understanding of the excitation mechanisms at low frequencies, in addition to that obtained in the RIVAS project. To date it is not yet clear what constitutes a complete measurement data set that would enable understanding most of the vibration excitation mechanisms in turnouts. Increasing vibration at turnouts in comparison to normal track is observed for all measured frequencies.
The different methodologies are presented in the paper. Under-sleeper pads (USP) are a cost-effective method to reduce vibration at frequencies above 63 Hz (1/3 octave), but there is probably no improvement for frequencies below 63 Hz. A first test of new frog geometry did not show relevant improvements in Vibration emission in comparison to a reference frog geometry. Axle box acceleration measurements are an interesting method to identify defects in a turnout. A specialized measurement system of rail roughness could identify certain geometry Problem areas for some frogs. Noise increases also are observed at turnouts for frequencies ranging between 80 to 1000 Hz. The use of railway source models to calculate
contact forces for ballasted track and turnouts seems promising, in particular for understanding the influence of ground.
The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site.
This document presents the specification for the execution and evaluation of high-speed tensile tests on reinforcement bar coupler systems. This specification was developed at BAM - Bundesanstalt für Materialforschung und -prüfung (Federal Institute for Materials Research and Testing, Germany) - following test principles from related international standards.
The present document represents the latest status of the test specification. It is noted that until 2010 the test procedure was characterised on a test velocity based on L0. In an improved test conception and after intensive investigations in cooperation with industry partners, this procedure has been updated to consider instead a test velocity based on Lr, since this warrants more comparable and meaningful results.
Fault detection for linear parameter varying systems under changes in the process noise covariance
(2020)
Detecting changes in the eigenstructure of linear systems is a comprehensively investigated subject. In particular, change detection methods based on hypothesis testing using Gaussian residuals have been developed previously. In such residuals, a reference model is confronted to data from the current system. In this paper, linear output-only systems depending on a varying external physical parameter are considered. These systems are driven by process noise, whose covariance may also vary between measurements. To deal with the varying parameter, an interpolation approach is pursued, where a limited number of reference models – each estimated from data measured in a reference state – are interpolated to approximate an adequate reference model for the current parameter. The problem becomes more complex when the different points of interpolation correspond to different noise conditions. Then conflicts may arise between the detection of changes in the eigenstructure due to a fault and the detection of changes due to different noise conditions. For this case, a new change detection approach is developed based on the interpolation of the eigenstructure at the reference points. The resulting approach is capable of change detection when both the external physical parameter and the process noise conditions are varying. This approach is validated on a numerical simulation of a mechanical system.
Fault detection for linear parameter varying systems under changes in the process noise covariance
(2020)
Detecting changes in the eigenstructure of linear systems is a comprehensively investigated subject. In particular, change detection methods based on hypothesis testing using Gaussian residuals have been developed previously. In such residuals, a reference model is confronted to data from the current system. In this paper, linear output-only Systems depending on a varying external physical parameter are considered. These systems are driven by process noise, whose covariance may also vary between measurements. To deal with the varying parameter, an interpolation approach is pursued, where a limited number of reference models { each estimated from data measured in a reference state { are interpolated to approximate an adequate reference model for the current parameter. The problem becomes more complex when the different points of interpolation correspond to different noise conditions. Then con icts May arise between the detection of changes in the eigenstructure due to a fault and the detection of changes due to different noise conditions. For this case, a new change detection approach is developed based on the interpolation of the eigenstructure at the reference points. The resulting approach is capable of change detection when both the external physical parameter and the process noise conditions are varying. This approach is validated on a numerical simulation of a mechanical system.
his presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The second lecture continues with the case of laterally loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
The dynamic behaviour of slab and ballast tracks has been investigated by measurements and calculations. Hammer impacts and train passages have been analysed. Measurements have been performed by geophones (velocity transducers) which have been time-integrated to displacements. The calculations are done in frequency-wavenumber domain for multi-beam-on-continuous soil models. The characteristics of the different tracks and track elements have been established in theory and experiment. The frequency-dependent compliances (displacement transfer functions) show clear rail-on-rail-pad resonances or highly damped track-soil resonances. Compared to the rail and sleeper, the track plate has much lower amplitudes. The slab track has usually the highest rail amplitudes due to soft rail pads. The train passage yields track displacements which are a superposition of the axle loads from the two neighbouring axles of a bogie and from the two bogies of two neighbouring carriages. This global behaviour is characteristic for the track plate of the slab track whereas the rails of the slab and the ballast track behave more local with only one bogie of influence. The measurements agree very well with the theory of the continuous soil in case of the six measured slab tracks and acceptably well for the six measured ballast tracks. The measurements allow to find appropriate model parameters and to check the models, for example the Winkler model of the soil has been found less appropriate as it reacts more locally.