7.2 Ingenieurbau
Filtern
Dokumenttyp
- Vortrag (168)
- Beitrag zu einem Tagungsband (67)
- Zeitschriftenartikel (16)
- Posterpräsentation (10)
- Dissertation (4)
- Beitrag zu einem Sammelband (3)
- Buchkapitel (2)
- Tagungsband (Herausgeberschaft für den kompletten Band) (1)
- Sonstiges (1)
Sprache
- Englisch (196)
- Deutsch (75)
- Mehrsprachig (1)
Referierte Publikation
- nein (272) (entfernen)
Schlagworte
- Structural Health Monitoring (22)
- Ground vibration (18)
- Fatigue (12)
- Offshore wind energy (11)
- Structural health monitoring (11)
- Monitoring (10)
- Brücken (9)
- Offshore (9)
- Impact (8)
- Building vibration (7)
- Damage characterization (7)
- Planar tomography (7)
- Vibration measurements (7)
- Bahnerschütterungen (6)
- Design methods (6)
- Deterioration (6)
- Hammer impact (6)
- Layered soil (6)
- Model interpolation (6)
- Numerical modelling (6)
- Offshore wind turbines (6)
- Physical phenomenology (6)
- Pile foundations (6)
- Soil-structure interaction (6)
- Structural systems (6)
- Grout (5)
- Inspection (5)
- Numeric simulation (5)
- Reinforced concrete structure (5)
- SHM (5)
- Train passage (5)
- Train-induced ground vibration (5)
- Vibration (5)
- Bayesian updating (4)
- Container loading (4)
- Crack detection (4)
- Damage detection (4)
- Datenmanagement (4)
- Drop test (4)
- Environmental effects (4)
- Erschütterungen (4)
- Erschütterungsminderung (4)
- Excitation forces (4)
- Foundation load (4)
- Foundations (4)
- Gründungsstrukturen (4)
- High-strength concrete (4)
- Interface (4)
- Layered soils (4)
- Modalanalyse (4)
- Reliability (4)
- Repair (4)
- Shell Buckling (4)
- Slab track (4)
- Steel structures (4)
- Temperature rejection (4)
- Ultrasonic testing (4)
- Vehicle-track-soil interaction (4)
- Wind Energy (4)
- Windenergie (4)
- BIM (3)
- Belastungsversuch (3)
- Bridges (3)
- Buckling (3)
- Compaction Grouting (3)
- Damage localization (3)
- Deep foundations (3)
- Dispersionsmessung (3)
- Elastische Gleiselemente (3)
- Emission (3)
- Erosion (3)
- Erschütterungsprognose (3)
- Fault detection (3)
- Großer Fallturm Horstwalde (3)
- Inspection planning (3)
- Leichtbau (3)
- Maintenance (3)
- Material moisture (3)
- Mitigation (3)
- Monopiles (3)
- Offshore Pile Foundation (3)
- Offshore Windenergieanlagen (3)
- Offshore foundations (3)
- Offshore geomechanics (3)
- Physical testing (3)
- Probabilistic (3)
- Reinforced concrete (3)
- Schwingungsdynamik (3)
- Subspace methods (3)
- Temperature effects (3)
- Train speed (3)
- Tunnel (3)
- Vibration measurement (3)
- Wellengeschwindigkeit (3)
- Wind (3)
- Zivile Sicherheit (3)
- 2-span bridge (2)
- AISTEC (2)
- Acceleration sensors (2)
- Acoustic emission testing (2)
- Amplitude-charge weight laws (2)
- Amplitude-distance laws (2)
- Analysis of variance (2)
- Ansys Autodyn (2)
- Apartment building (2)
- Artificial intelligence (2)
- Attenuation (2)
- Automatisierte schweißtechnische Fertigung (2)
- Axle-sequence spectrum (2)
- Bayes'sche Analyse (2)
- Bayesian System Identification (2)
- Bayesian methods (2)
- Bemessung (2)
- Big Data (2)
- Bitumen (2)
- Bodenübertragungsfunktion (2)
- Box-Behnken (2)
- Brücke (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Changing process noise (2)
- Chemisoprtion (2)
- Climate chamber (2)
- Compressive Cyclic loading (2)
- Compressive cyclic loading (2)
- Compressive strength (2)
- Coupled fluid-particle simulation (2)
- Coupler systems (2)
- Crack formation (2)
- Crack pattern (2)
- Cracks (2)
- Cyclic load (2)
- DEM (2)
- DUCON® (2)
- Design (2)
- Digital twin (2)
- Displacements (2)
- Drone (2)
- Drucker-Prager (2)
- Ductility (2)
- E-modulus (2)
- Earth masonry (2)
- Elastische Elemente (2)
- Energy (2)
- Erschütterungsausbreitung (2)
- Evaluation (2)
- Explosion-induced ground vibrations (2)
- Faseroptik (2)
- Feuchte (2)
- Filter effects (2)
- Finite Elemente Simulation (2)
- Finite element models (2)
- Fly ash (2)
- Freight train (2)
- GPU parallel computation (2)
- Gleiströge (2)
- Ground vibration measurements (2)
- Grouted Connection (2)
- Grouted connection (2)
- Grouting (2)
- Halbraum (2)
- High-performance computing (2)
- High-speed (2)
- High-speed train (2)
- Immission (2)
- Injection Sequence (2)
- Irregularities (2)
- Klimakammer (2)
- Knudsen effect (2)
- Laboratory beam structure (2)
- Lehm (2)
- Linear parameter varying systems (2)
- Load vector (2)
- Long-term shrinkage (2)
- Macromechanical Sample Strength (2)
- Material tests (2)
- Mauerwerk (2)
- Measurement (2)
- Measurements (2)
- Messen im Bauwesen (2)
- Metakaolin (2)
- Micro silica (2)
- Micro-reinforcement (2)
- Micromechanical Tensile Failure (2)
- Micromechanical modelling (2)
- Mobile elements (2)
- Modal Analysis (2)
- Molecular diffusion (2)
- Non destructive testing (2)
- Non-destructive testing (2)
- Numerical model (2)
- Numerical modeling (2)
- Office tower (2)
- Offshore Wind Energy (2)
- Offshore Windenergy Pile Buckling (2)
- Offshore geotechnics (2)
- Offshore wind (2)
- Offshore wind turbine (2)
- Offshore-Windenergieanlagen (2)
- Optimal Sensor Placement (2)
- Passenger train (2)
- Physisorption (2)
- Pile Foundation (2)
- Pile Tip Buckling (2)
- Post-impact evaluation (2)
- Prediction (2)
- Prediction of explosion induced ground and building vibration (2)
- Prädiktive Instandhaltung (2)
- Quasi-static and dynamic tests (2)
- Radar (2)
- Railway (2)
- Railway bridge (2)
- Railway tunnel (2)
- Railways (2)
- Randomly heterogeneous soil (2)
- Rehabilitation (2)
- Reinforcement (2)
- Research data management (2)
- Risk (2)
- Risslumineszenz (2)
- SDDLV (2)
- Scattering (2)
- Schadensdetektion (2)
- Schwingungsbasierte Verfahren (2)
- Size effect (2)
- Slenderness effect (2)
- Soil properties (2)
- Soil-Structure-Interaction (2)
- Soil-pile interaction (2)
- Soil-wall-floor model (2)
- Static load (2)
- Statistical evaluation (2)
- Statistical method (2)
- Stereo photogrammetry (2)
- Subspace-based method (2)
- Subspace-based residual (2)
- Suction bucket (2)
- Supplementary cementitious materials (2)
- Surface-tunnel reduction (2)
- System Identification (2)
- Tensile Capacity (2)
- Time-variant reliability (2)
- Tomographic damage evaluation (2)
- Track damage (2)
- Train excitation (2)
- Transmission (2)
- UHPC (2)
- Umwelteinflüsse (2)
- Unterraummethoden (2)
- Value of Information (2)
- Vehicle-track interaction (2)
- Vibrations (2)
- Vollraum (2)
- Wellenausbreitung (2)
- Wellenausbreitung in der Tiefe (2)
- Wind Turbines (2)
- Windenergy (2)
- Zuggeschwindigkeit (2)
- Zuverlässigkeit (2)
- 3D imaging (1)
- Achsfolgespektren (1)
- Achsimpulse (1)
- Amplituden-Abstands-Gesetze (1)
- Analytical Design Methods (1)
- Artificial Intelligence (1)
- Asphalt (1)
- Assessment (1)
- Asymptotic local approach (1)
- Automatic modal parameters identification (1)
- Automatisierte Fertigung (1)
- Automatisierte schweißtechniche Fertigung (1)
- Axial load bearing (1)
- Axle impulses (1)
- Axle loads (1)
- Axle pulses (1)
- BAM Windenergie Fügetechnik (1)
- Bahngleis (1)
- Ballast track (1)
- Base isolation (1)
- Baugrunddynamik (1)
- Bauteile (1)
- Bauwerk-Boden-Wechselwirkung (1)
- Bauwerke (1)
- Bauwerksmonitoring (1)
- Bauwerksüberwachung (1)
- Bayesian analysis (1)
- Bayesian system identification (1)
- Beanspruchungszustand (1)
- Belastungsfahrt (1)
- Belastungszug (1)
- Beton (1)
- Betonautobahn (1)
- Betonautobahnen (1)
- Beulen (1)
- Bewertung (1)
- Bionik (1)
- Blast (1)
- Blast tests (1)
- Bodenschlitz (1)
- Bodenvariabilität (1)
- Boundary element method (1)
- Bridge (1)
- Bridge monitoring (1)
- Bruchlastwechselzahlen (1)
- Brückensicherheit (1)
- Buckling piles circular shells (1)
- Building information modelling (1)
- Building response (1)
- Bulging (1)
- CFD (1)
- Cars (1)
- Centerline solidification cracking (1)
- Chemisorption (1)
- Civil structures (1)
- Climate Chamber (1)
- Cohesive soils (1)
- Column/wall resonance (1)
- Combined finite-element boundary-element method (1)
- Components of excitation (1)
- Computer Vision (1)
- Concrete (1)
- Conductor (1)
- Crack (1)
- Crack Luminescence (1)
- Crack growth (1)
- Crack repair (1)
- Cyclic axial shearing (1)
- Cyclic degradation (1)
- DEM-LBM simulation (1)
- Damage Detection (1)
- Damage identification (1)
- Deckeneigenfrequenzen (1)
- Deckenschwingungen (1)
- Design models (1)
- Design practice (1)
- Detection (1)
- DiMoWind RDS-PP Maintenance Digital Twin Offshore Wind Energy (1)
- Digital Image Correlation (1)
- Digital Models (1)
- Digital Twin (1)
- Digitale Zwillinge (1)
- Digitalisierung (1)
- Drop Test (1)
- Drop Tests (1)
- Drop tower (1)
- Druckfestigkeit (1)
- Druckschwellenversuch (1)
- Dynamic loads (1)
- Dynamic soil properties (1)
- Dynamische Bodenkennwerte (1)
- Dynamische Bodensteifigkeit (1)
- Dämpfung (1)
- EERA Joint Program (1)
- Earth (1)
- Earth material (1)
- Earthen hydraulic constructions (1)
- Earthen hydraulic infrastructures (1)
- Einflusslinie (1)
- Einflusslinien (1)
- Einfügungsdämmung (1)
- Elastische Gebäudelagerung (1)
- End-of-life decision making (1)
- Entscheidungsfindung (1)
- Environmental (1)
- Environmental Effects (1)
- Environmental influence (1)
- Erhaltungsmanagement (1)
- Ermüdungsprüfung (1)
- Ermüdungsschäden (1)
- Ermüdungsverhalten (1)
- Erneuerbare Energien (1)
- Erosion of cohesive soils (1)
- Erschütterungen im Fernfeld (1)
- FEM (1)
- FEM analysis (1)
- Fahrzeug-Fahrweg-Boden-Wechselwirkung (1)
- Fallturm (1)
- Fatigue damage (1)
- Fatigue deterioration (1)
- Fiber optic sensing (1)
- Finite element method (1)
- Finite element model updating (1)
- Finite-Elemente-Modellkalibrierung (1)
- Flexibility (1)
- Flexible car body (1)
- Flexible wheelset (1)
- Floor resonance (1)
- Floors (1)
- Fluid-structure interaction (1)
- Footbridge (1)
- Force reconstruction (1)
- Foundation Pile (1)
- Foundation reliability analysis (1)
- Freileitung (1)
- Frequency response function (1)
- GMNIA (1)
- GNSS (1)
- GPU parallelisation (1)
- Gebäudelagerung (1)
- Gebäudemodelle (1)
- Gebäudeschwingungen (1)
- Geomechanics (1)
- Geomechanics of offshore foundations (1)
- Geometrie (1)
- Global ambient vibrations (1)
- Granular Cohesive Materials (1)
- Granular Cohesive Materials, (1)
- Ground (1)
- Grout Injection (1)
- HTLS (1)
- Hard impact (1)
- Harter Anprall an Stahlbetonstrukturen (1)
- High-Rise Building (1)
- High-rise buildings (1)
- Horizontal stress (1)
- IEPE (1)
- Impact damage of reinforced concrete (1)
- Impact damage on reinforced concrete (1)
- Impakt (1)
- Impedanzmethode (1)
- Inertial Interaction (1)
- Inertial interaction (1)
- Inhomogeneous soils (1)
- Innovative Messtechnik (1)
- Inspeciton (1)
- Inspektion (1)
- Interface model (1)
- Irregular ballast (1)
- Irregular soil (1)
- Jacket support structure (1)
- Jet erosion test (1)
- Kinematic Interaction (1)
- Kinematic interaction (1)
- Kraft auf den Boden (1)
- LBM-DEM (1)
- LBM-DEM coupling (1)
- LBM-DEM simulation (1)
- Laminography (1)
- Laser beam welding (1)
- Lateral load bearing (1)
- Leichtbauprinzipien (1)
- Load Test (1)
- Load bearing behaviour (1)
- Load-bearing (1)
- Long-span bridge (1)
- Low-frequency shaker (1)
- Luminescence (1)
- MEMS (1)
- Maintal Bridge Gemuenden (1)
- Maintalbrücke Gemünden (1)
- Maintenance Digital Twin Offshore Wind Energy (1)
- Marine geomechanics (1)
- Marine geotechnics (1)
- Maschinenbetrieb (1)
- Material Point Method (1)
- Material model (1)
- Measurement campaigns (1)
- Mechanical challenges (1)
- Messfahrt (1)
- Microfine cement (1)
- Micromechanical LBM-DEM simulation (1)
- Micromechanical analysis (1)
- Micromechanical simulation (1)
- Minderungsmaßnahmen (1)
- Mix design (1)
- Modal force spectrum (1)
- Modal load spectrum (1)
- Modal system identification (1)
- Model Update (1)
- Model updating (1)
- Modellierung (1)
- Modes (1)
- Modes and waves (1)
- Moisture (1)
- Monopile (1)
- Monopile Buckling (1)
- Monopile installation risks (1)
- Movin load test (1)
- Multi-beam method (1)
- Multiple impact (1)
- NDT (1)
- Nachgiebigkeiten (1)
- Nelson’s method (1)
- Non-Destructive Evaluation (1)
- Normung (1)
- Numerical analysis (1)
- Numerical damage simulation (1)
- Numerical simulation (1)
- Numerical simulation of impact damage (1)
- Numerical simulations (1)
- Offhore (1)
- Office building (1)
- Offshore Structures (1)
- Offshore Wind (1)
- Offshore Wind Energy Converter (1)
- Offshore Windenergie (1)
- Offshore pile foundations (1)
- Offshore wind energy foundations (1)
- Offshore wind farm (1)
- Offshore wind farms (1)
- Offshore wind-turbine foundations (1)
- Offshore-Wind (1)
- Operational modal analysis (1)
- Optimierungsmethoden (1)
- Optimization techniques (1)
- Pfahlfußbeulen (1)
- Pfahlnachgiebigkeiten (1)
- Physisoprtion (1)
- Pile Buckling (1)
- Pile Capacity (1)
- Pile ageing (1)
- Pile groups (1)
- Pile retrofit system (1)
- Pile-Tip-Buckling (1)
- Point Cloud (1)
- Predictive maintenance (1)
- Probabilistic modelling (1)
- Probabilitische Ingenieurmodelle (1)
- Probability of Detection (1)
- Probability of detection (1)
- Probekörpergeometrien (1)
- Prognose (1)
- Propagation from a tunnel (1)
- Railbridge (1)
- Railway induced vibration (1)
- Railway track (1)
- Railway tracks (1)
- Railway trafiic (1)
- Randelementmethode (1)
- Rayleighwellendispersion (1)
- Rechenmodelle (1)
- Rechenverfahren (1)
- Repowering (1)
- Residential building (1)
- Residual evaluation (1)
- Richtige Fahrzeugmasse (1)
- Rigid vehicle model (1)
- Risiko (1)
- Risikoanalyse (1)
- Risk-based maintenance planning (1)
- Rissprozes (1)
- Rissprozess (1)
- Road bridges (1)
- SHM Environmental (1)
- Safety (1)
- Scaling (1)
- Scattered axle impulses (1)
- Schadensüberwachung (1)
- Scherwellengeschwindigkeit (1)
- Schienenfahrweg (1)
- Schienenfahrwege (1)
- Schubmodul (1)
- Schwingungsmessungen (1)
- Schwingungsmonitoring (1)
- Schädigungsprozesse (1)
- Sensitivity vectors (1)
- Shearing (1)
- Shrinkage (1)
- Sicherheit (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Simulation and experiment (1)
- Site-characterization (1)
- Soft impact (1)
- Soft track elements (1)
- Soil Struture Interaction (1)
- Soil erosion (1)
- Soil-building interaction (1)
- Soil-building resonance (1)
- Soil-wall floor model (1)
- Soil-water-structure interaction (1)
- Spatially varying ground conditions (1)
- Spektralanalyse (1)
- Stability Buckling soil-structure-interaction piles offshore (1)
- Stabilität (1)
- State of stress (1)
- Statistical correlations (1)
- Statistical tests (1)
- Statistische Auswertung (1)
- Statistische Korrelationen (1)
- Stochastic Subspace Damage Detection (1)
- Strength (1)
- Stress stiffening (1)
- Structural Systems (1)
- Structural integrity (1)
- Structural integrity maintenance (1)
- Structural integrity management (1)
- Strukturmonitoring (1)
- Störgrößen (1)
- Substructures (1)
- Support structures (1)
- Surface Foundation (1)
- Surface line (1)
- Switch (1)
- System identification (1)
- Systemidentifikation (1)
- TOP (1)
- Tagung (1)
- Temperatureinflüsse (1)
- Tensile test (1)
- Test specification (1)
- Tip Buckling (1)
- Track and vehicle irregularities (1)
- Track beam (1)
- Track damage monitoring (1)
- Track damage quantification (1)
- Track vibration (1)
- Track-soil interaction (1)
- Tragfähigkeit (1)
- Tragstrukturen (1)
- Train configuration (1)
- Train passages (1)
- Tran speed (1)
- Transfer fuction (1)
- Transfer function (1)
- Truss structures (1)
- Tunnel line (1)
- Tunnel-pile transfer (1)
- Tunnelstrecke (1)
- Turnout (1)
- Un- certainty (1)
- Uncertainty (1)
- Uncertainty in reference (1)
- Uncertainty quantification (1)
- Under-sleeper pads (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Varying track stiffness (1)
- Vibration analysis (1)
- Vibration excitation (1)
- Vibration monitoring (1)
- Wahrscheinlichkeit (1)
- Water-structure interaction (1)
- Wave-Tower interaction (1)
- Wavenumber integrals (1)
- Wavenumber method (1)
- Waves (1)
- Welded (1)
- Wellenfeldberechnung (1)
- Wheelset accelerations (1)
- Wind Energy Structures (1)
- Wind energy (1)
- Wind turbines (1)
- Wind-farm aerodynamics (1)
- Windenergieanlagen (1)
- Windfarm wake analysis (1)
- Zerstreute Achsimpulse (1)
- building information modelling (1)
- elastische Gebäudelagerungen (1)
- fachwerkartige Stahltragwerken (1)
- risk, reliability, inspection planning, offshore wind turbines (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- zerstreute Achslastimpulse (1)
- Übertragungsmatrizen (1)
- Überwachung (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (272) (entfernen)
The Stochastic Dynamic Damage Locating Vector (SDDLV) approach is a vibration-based damage localization method based on both a finite element model of a structure and modal parameters estimated
from output-only measurements in the damage and reference states. A statistical version of the Approach takes into account the inherent uncertainty due to noisy measurement data. In this paper, the effect of temperature fluctuations on the performance of the method is analyzed in a model-based approach using a finite element model with temperature dependent parameters. Robust damage localization is carried out by rejecting the temperature influence on the identified modal parameters in the damaged state. The algorithm is illustrated on a simulated structure.
The Stochastic Dynamic Damage Locating Vector (SDDLV) approach is a vibration-based damage localization method based on both a finite element model of a structure and modal parameters estimated from output-only measurements in the damage and reference states. A statistical version of the Approach takes into account the inherent uncertainty due to noisy measurement data. In this paper, the effect of temperature fluctuations on the performance of the method is analyzed in a model-based approach using a finite element model with temperature dependent parameters. Robust damage localization is carried out by rejecting the temperature influence on the identified modal parameters in the damaged state. The algorithm is illustrated on a simulated structure.
Lehmmauerwerk bietet sich aufgrund seiner zahlreichen ökologischen Vorteile für die Errichtung klimafreundlicher und ressourcenschonender Gebäude an. Um den Anwendungsbereich tragenden Lehmmauerwerks durch eine zeitgemäße Nachweisführung zu erweitern, werden in diesem Beitrag Grundlagen für die Entwicklung eines eurocodekonformen Bemessungskonzepts erarbeitet. Hierzu werden die Ergebnisse umfangreicher experimenteller Untersuchungen an Lehmmauerwerk sowie Lehmsteinen und -mörteln nach Konditionierung bei unterschiedlichen Klimata vorgestellt. Darauf aufbauend erfolgt eine Traglastanalyse druckbeanspruchter Lehmmauerwerkswände mittels numerischer und analytischer Methoden. Die daraus gewonnenen Erkenntnisse werden abschließend in einen an DIN~EN~1996-3/NA angelehnten Bemessungsvorschlag überführt, welcher die materialspezifischen Besonderheiten von Lehmmauerwerk berücksichtigt und eine fundierte Grundlage für eine wirtschaftliche und zuverlässige Nachweisführung darstellt.
Protection against terroristic or accidental scenarios in industrial settings requires suitable designs of structures to resist blast loads. Field testing as well as finite element simulations are among the techniques available to engineers in the understanding of the structural behavior against blast loading.
As blast testing of complex scenarios can be very resource intensive, tests are generally performed for simplified scenarios. Numerical tools can be used to model these scenarios to get better insight into blast loading, structural response, and the resulting damage to the structure. During the next steps, the simplified scenario is successively modified in numerical simulations to incorporate complexities that cannot be covered in blast testing experiments. One of the conditions for this approach to work is that the original simplified numerical simulation is valid. The scopes and challenges encountered in such a validation are the focus of this presentation/article.
A relatively ‘simple’ field test of a horizontal reinforced concrete (RC) slab subjected to blast loading is taken as an example for validation of the performance of numerical tools. The blast test incorporated various measurement techniques to quantify the blast load as well as the behavior of the RC slab. Blast load was measured using flush mounted piezoelectric pressure gauges, whereas acceleration sensors and fiber-optic sensor cables were used to characterize the dynamic behavior of the slab under blast loading. Additionally, damage characteristics were ascertained also using fiber optic sensing. The application of such measurement techniques, along with different numerical software available for the analysis of the scenario in question, demonstrate the scope of our contribution.
When it comes to the challenges, it begins with proper instrumentation of the test specimen followed by the data processing. For numerical modelling, geometric conditions with appropriate boundary constraints, physical conditions such as the configuration of the rebars, as well as material parameters add to this challenge. The issues of choosing appropriate material models and comparison of results with multiple software tools will be discussed. This discussion forms the basis for a coherent approach to technical-safety assessment of blast effects on structures in its broader sense.
This talk provides a brief overview on some geomechanical phenomena and problematic issues in the field of offshore wind-energy geotechnics, with reference to their associated challenges for a numerical analysis/simulation. These may include large deformations, fluid coupling and grain-scale phenomena, all of which are generally difficult to be addressed with conventional FE techniques.
These challenges are illustrated here with a practical example for the retrofit of axially loaded piles using compaction grouting techniques. In this case, the mechanical effects of the retrofit may be analysed with standard FE techniques, but require the adoption of strong assumptions, while the injection process itself can only be analysed with special techniques such as the MPM.
Finally, an LBM-DEM framework for the micromechanical analysis of such problems is introduced and a practical application for the estimation of the soil resistance to driving (SRD) in layered profiles is discussed.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
Design challenges for offshore wind-farms. From foundation mechanics to wind-farm aerodynamics
(2018)
This talk provides a brief introduction on general engineering aspects of offshore wind energy production. Then some geomechanical issues for the foundation of OWTs into the seabed are introduced, while the results from experimental investigations and coupled computational analysis are discussed.
In the second part of the seminar, the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out.
Concerning the geomechanical issues the talk shows that: i) The pile’s bearing capacity can degrade under cyclic loading (waves, wind, …). ii) The time effects can be relevant: Capacity improvement can be substantial, but also fragile. iii) There are cyclic PWP effects: Cyclic interaction with pore water may lead to soil softening and an uncoupled analysis (current design practice) is potentially unsafe.
And concerning the hydromechanical and aerodynamical design considerations, this seminar shows that: i) Numerical analysis of turbine’s interaction with wind/waves is useful and affordable. ii) Simplified models can provide insight into windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided in two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of these two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
Deep foundations for offshore wind turbines. Lecture 2: lateral behaviour and advanced topics
(2020)
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
This presentation provides an overview on general issues related to erosive failures in civil constructions like hydraulic infrastructures and offshore foundations. A brief introduction to the related research activities of BAM in the field of offshore wind energy is first provided, and the general possibilities for micromechanical modelling approaches are outlined. Finally, the ongoing DFG-ANR research project COMET is introduced.
This talk provides a brief introduction on general engineering challenges for the offshore (marine) wind energy production, focusing on material, structural and hydromechanical aspects.
The talk begins with a broad overview on general trends for offshore wind-farms, with insights on some characteristic structural features and their associated loads. Then, some particular open issues for the foundation of the offshore wind turbines into the seabed are introduced. Here, different research approaches are discussed, from experimental investigations to coupled computational analysis at micro- and macroscopic scales.
In the second part of the seminar, both the hydromechanical Wave–Tower interaction and some general aspects of the windfarm aerodynamics (wake analysis) are discussed. Some modelling possibilities in the frame of CFD (computational fluid dynamics) are introduced and the relevance of such analyses for a proper windfarm layout optimization is pointed out.
Summing up, this seminar aims to show that: i) Numerical analysis of the turbine’s interaction with wind/waves and with the seabed is both useful and affordable. ii) Simplified models can provide an insight into windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout.
Driven steel piles are commonly used as deep foundations for a wide range of engineering structures, particularly in the offshore branch. They are also an interesting example among the broad spectrum of geotechnical applications where the fluid-solid interaction at the pore-scale can play a major role for the macromechanical behaviour of the whole system.
In the context of the geotechnical practice for offshore wind-farm structures, both the industrial design and the actual dimensions of the large piles used as foundations in the seabed are often driven by factors such as the soil resistance to driving (SRD), which are still not well understood and often estimated based on mere empirical correlations or overly simplified one-dimensional models. In particular, the role of the micromechanical effects during the installation process (e.g. local dilatancy or contractancy) and their consequences on the pore pressure levels at the pile-tip and on the effective resistance to driving, are generally either disregarded or at most assumed to be covered by the simplified engineering “black-box” solutions.
Here, we propose a general framework to address such local aspects of a geotechnical application involving fluid-saturated soils while retaining the focus on the micro-scale phenomena. We advocate for an approach that combines the relative simplicity of the Discrete Element Method (DEM) for the solid mechanics with the capabilities of the Lattice Boltzmann Method (LBM) for the fluid dynamics. In this sense, we aim to compile some useful techniques and practical recommendations for an efficient GPU-based implementation of a micromechanical LBM-DEM simulation tool.
We present here a set of conceptual and numerical tools for a micromechanical simulation of general erosion problems involving fluid-saturated granular assemblies, whether frictional or cohesive. We propose a parallel computation using graphical processing units (GPUs) to treat large numbers of degrees of freedom with conventional desktop computers.
The fluid phase is here simulated with a particle-resolved approach in the frame of the Lattice Boltzmann Method (LBM) while the granular solid phase is modelled as a collection of discrete particles from a Molecular Dynamics DEM perspective. The range of possible material behaviors for the solid granular phase is intended here to cover a broad spectrum from purely frictional to viscous cohesive materials with either brittle or transient debonding features. Specific details of the implementation and some validation cases will be put forward.
To conclude we provide some exemplary applications in the field of soil erosion along with details on the parallel performance of the models. The results show that a micromechanical approach can be feasible and useful in practice, providing meaningful insights into complex phenomena like the erosion threshold and kinetics of weakly cemented soils.
State of the art and development perspectives of deep foundations for offshore wind converters
(2020)
This presentation provides an overview of the main geotechnical aspects associated with deep foundations in the context of offshore wind generation. The most common deep foundation typologies (large diameter monopiles and multipile typologies) as well as new trends under development (e.g. suction buckets) and their current limits will be briefly described. The talk concludes with a brief review of advanced topics not covered in classical pile design, such as hydromechanical coupling effects (pore pressure generation), cyclic accumulation of deformations, cyclic degradation of axial capacity or pile-setup gains.
Design challenges for Offshore wind-farms. From foundation mechanics to wind-farm aerodynamics
(2021)
This talk provides a brief introduction on general engineering design challenges for the offshore wind energy production. Some general features of the offshore wind-energy field from a civil engineering perspective are firstly presented, followed by a brief discussion of some of the main geomechanical issues for the foundation of the offshore turbines into the seabed.
In the following part, an overview of relevant fluid-structure interactions and some options for an efficient numerical analysis are provided, where the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out.
In particular, this talk shows that: i) The bearing capacity of turbine multi-pile foundations can degrade under cyclic loading (waves, wind, …), while for monopile foundations cyclic hydromechanical coupling effects may take place, which may lead to a foundation softening; ii) Numerical analysis of a turbine’s interaction with wind/waves is useful and affordable, while simplified models can already provide a useful insight into the windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
his presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The second lecture continues with the case of laterally loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided in two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of these two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
This talk provides a brief introduction on general engineering aspects of offshore wind energy production. Some geomechanical issues for the foundation of OWTs into the seabed are introduced, while the results from experimental investigations and coupled computational analysis are discussed.
In the second part of the seminar, the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out.
Concerning the geomechanical issues the talk shows that: i) The pile’s bearing capacity can degrade under cyclic loading (waves, wind, …). ii) The time effects can be relevant: Capacity improvement can be substantial, but also fragile. iii) There are cyclic PWP effects: Cyclic interaction with pore water may lead to soil softening and an uncoupled analysis (current design practice) is potentially unsafe.
And concerning the hydromechanical and aerodynamical design considerations, this seminar shows that: i) Numerical analysis of turbine’s interaction with wind/waves is useful and affordable. ii) Simplified models can provide insight into windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here.
The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile Setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
Design challenges for Offshore wind-farms. From foundation mechanics to wind-farm aerodynamics
(2023)
This talk provides a brief introduction on general engineering design challenges for the offshore wind energy production. Some general features of the offshore wind-energy field from a civil engineering perspective are firstly presented, followed by a brief discussion of some of the main geomechanical issues for the foundation of the offshore turbines into the seabed.
In the following part, an overview of relevant fluid-structure interactions and some options for an efficient numerical analysis are provided, where the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out.
In particular, this talk shows that: i) The performance and behavior of the turbine's foundation is often conditioned by the appearance of large deformations, fluid couplings and grain-scale phenomena, whereby specific physical testing (both in field and lab conditions) and ad-hoc simulation techniques can provide useful insights for design; ii) Numerical analysis of a turbine’s interaction with wind/waves is already affordable in engineering scales, while simplified models can already provide a useful insight into the windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout.
This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures.
The second lecture continues with the case of laterally loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended.
Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles.
One crucial metric of interest to wind farm operators is the remaining useful life (RUL) of single components, wind turbines, or even entire wind farms. Occasionally, questions arise regarding how to operate a turbine, even in the presence of manufacturing or design errors, which from a computational design standpoint reduce the remaining lifetime below the intended service life. A typical measure involves adapting the monitoring and inspection plan. Using such a maintenance plan, the author intends to simulate the lifetime of jacket-type structure in a fatigue test. The objective of the experiment is to demostrate that systems like three-dimensional jackets possess redundancies that enable reliable continued operation, despite the reduced fatigue life of individual components due to technical flaws, if an appropriate maintenance concept is in place. This presentation discusses the steps leading to the procedure of the experiment including the design process and the maintenance planning.
A digital structural integrity management of offshore structures enables an optimized planning of inspections and repairs with risk-based methods. In a risk-based approach, the inspection and repair strategy that minimizes the expected lifetime costs consisting of the expected inspection, repair and failure costs is determined. In addition to inspections, information on the structural condition can be continuously obtained by monitoring the vibration response of the structural system. Changes in the vibration characteristics quantified in terms of modal properties can be an indication of structural damage. In risk-based inspection and repair planning, the effect of monitoring results is determined via Bayesian updating of the structural condition and reliability. This information should be applied to inform decisions on inspections and may result in a reduced inspection effort. The benefit of continuously monitoring the structural health can be quantified in terms of the value of information, which corresponds to the difference between the expected lifetime costs with and without monitoring. In this work, we demonstrate in a numerical example how an optimized sensor placement for a vibration-based structural health monitoring system can be determined by maximizing the value of information.
Support structures of wind turbines in German offshore wind farms are regularly inspected. Currently, inspection outcomes are generally not systematically recorded. This prevents their consistent handling and processing, which is a key requirement to enable an efficient structural integrity management. As part of the DiMoWind-Inspect project, a data model and reference designation system for such inspection results is developed to facilitate their identification, localization, quantification, tracing and linking throughout the lifetime of a wind farm and beyond. The inspection results together with structural health monitoring results and information on repairs form the basis for assessing and predicting the structural condition, estimating the remaining lifetime, and planning of future inspections, structural health monitoring, and repairs. As a basis for developing a digital structural integrity management, a generic framework is proposed in this paper, which describes the stakeholders, data, models, processes and workflows of the integrity management of support structures in offshore wind farms and their interrelations. The framework adopts a building information modelling approach to describe the information relevant to the structural integrity management. The central digital space of the framework is a common data environment. An implementation of the framework will enable a digital structural integrity management in which inspection, structural health monitoring, repair, assessment and planning outcomes generated throughout the life cycle of a wind farm can be consistently collected, managed, shared and processed by the relevant shareholders.
Support structures of wind turbines in German offshore wind farms are regularly inspected. Currently, inspection outcomes are generally not systematically recorded. This prevents their consistent handling and processing, which is a key requirement to enable an efficient structural integrity management. As part of the DiMoWind-Inspect project, a data model and reference designation system for such inspection results is developed to facilitate their identification, localization, quantification, tracing and linking throughout the lifetime of a wind farm and beyond. The inspection results together with structural health monitoring results and information on repairs form the basis for assessing and predicting the structural condition, estimating the remaining lifetime, and planning of future inspections, structural health monitoring, and repairs. As a basis for developing a digital structural integrity management, a generic framework is proposed in this paper, which describes the stakeholders, data, models, processes and workflows of the integrity management of support structures in offshore wind farms and their interrelations. The framework adopts a building information modelling approach to describe the information relevant to the structural integrity management. The central digital space of the framework is a common data environment. An implementation of the framework will enable a digital structural integrity management in which inspection, structural health monitoring, repair, assessment and planning outcomes generated throughout the life cycle of a wind farm can be consistently collected, managed, shared and processed by the relevant shareholders.
A digital structural integrity management of offshore structures enables an optimized planning of inspections and repairs with risk-based methods. In a risk-based approach, the inspection and repair strategy that minimizes the expected lifetime costs consisting of the expected inspection, repair and failure costs is determined. In addition to inspections, information on the structural condition can be continuously obtained by monitoring the vibration response of the structural system. Changes in the vibration characteristics quantified in terms of modal properties can be an indication of structural damage. In risk-based inspection and repair planning, the effect of monitoring results is determined via Bayesian updating of the structural condition and reliability. This information should be applied to inform decisions on inspections and may result in a reduced inspection effort. The benefit of continuously monitoring the structural health can be quantified in terms of the value of information, which corresponds to the difference between the expected lifetime costs with and without monitoring. In this work, we demonstrate in a numerical example how an optimized sensor placement for a vibration-based structural health monitoring system can be determined by maximizing the value of information.
Schutzbauwerke von systemkritischen Infrastruktureinrichtungen wie Betonwände und Betonbarrieren müssen Anprallereignissen oder schweren Unfällen in einem vertretbaren Maße widerstehen können. Anprallereignisse können verschiedenster Natur sein. Hierzu zählen Steinschlag, Fahrzeug- oder Flugzeuganprall oder auch Geschosseinschlag. Geschosseinschläge bzw. Bei den Anprall- oder Impaktereignissen wird zwischen hartem und weichem Anprall unterschieden, bei hartem Anprall verformt sich der Anprallkörper nicht oder nur geringfügig, bei weichem Anprall stark.
In diesem Artikel werden Forschungsergebnisse zum harten Anprall auf bewehrte Stahlbetonplatten vorgestellt, welche über die letzten Jahre im Rahmen eines Kooperationsprojekts zwischen dem Institut für Massivbau (IMB) der Technischen Universität Dresden (TUD) und der Bundesanstalt für Materialforschung und -prüfung (BAM) durchgeführt wurden. Auf dem Gelände des Otto-Mohr-Labors (OML) der TUD steht hierfür ein speziell konzipierter Fallturm zur Verfügung. Der Aufbau im Fallturm lässt aktuell druckluftbeschleunigte Impaktversuche mit mittleren Anprallgeschwindigkeiten zu. Die durch Anprall geschädigten Stahlbetonplatten wurden anschließend bei der BAM mit Strahlung tomographisch untersucht. Diese Untersuchungen ermöglichen einen Blick auf die Schädigung und Rissstruktur im Inneren der Stahlbetonplatten.
Ein Schwerpunkt der durchgeführten Untersuchung ist der Vergleich von Testergebnissen mit den häufig angewendeten halbempirischen Berechnungsmethoden zu den erforderlichen Wandstärken und den sich daraus ergebenden zulässigen Anprallgeschwindigkeiten. Bei diesem Vorgehen wird auch die mit analytischen Methoden abschätzbare Durchdringungsgeschwindigkeit bzw. Austrittgeschwindigkeit eines Projektils ermittelt und mit den realen Testergebnissen verglichen. Außerdem wird der Einfluss von sowohl externen als auch internen Strukturparametern auf Risse betrachtet und ein Fazit abgeleitet. Weiterhin werden laufende und zukünftige wissenschaftliche Untersuchungen zum Anprall auf Betonstrukturen am IMB und der BAM genannt.
Severe mechanical fatigue conditions for worldwide proliferating windfarms are a Major challenge for high-performance concrete in towers, connecting joints and foundations of wind turbines. High-performance concrete offers potential for the application in offshore windfarms, not only regarding its good mechanical, but also chemical resistivity due to low diffusivity in the highly densified microstructure. For a more reliable fatigue assessment, monitoring based on nondestructive testing can be a valuable complement to design rules. Both approaches demand reliable experimental data, information about scalability and the development of standardized testing methods. This article presents results of an ongoing research program of BAM (Bundesanstalt für Materialforschung und -prüfung), which is a part of a joint national project (WinConFat) funded by the German Federal Ministry for Economic Affairs and Energy. The subproject implemented by BAM examines the fatigue behavior in dependence of size and slenderness for varying concrete strength at different stress levels. Besides fatigue strength, nondestructive testing is carried out additionally.
Methods used are strain measurement and ultrasonic testing. The change of strain, stiffness and ultrasonic pulse velocity in the fatigue process is discussed. Results disclose a deeper insight into the damage process under cyclic loading of high-performance concrete and contribute to improve nondestructive monitoring.
The worldwide spread of windfarms brings new challenges, especially for concrete structures as a part of towers, connecting joints and foundations of wind turbines. High-cyclic loadings in such structures lead to a high relevance of the subject of fatigue. A proper assessment of the fatigue strength of concrete demands therefore a basis of reliable experimental data and the development of standardized testing methods. This article presents first results of an ongoing research program of BAM (Bundesanstalt für Materialforschung und -prüfung) which is a part of a joint project (WinConFat) funded by the German Federal Ministry for Economic Affairs and Energy. The subproject investigates the effects of size and slenderness of the specimens on the fatigue behaviour of high strength concrete at different stress levels. Not only the fatigue strength, but also the fatigue process itself is monitored by means of several measurement methods. Strain measurements are used to calculate the load dependent elastic modulus in the fatigue hysteresis as indicators for fatigue development. Furthermore, the application of non-destructive methods like acoustic emission analysis and ultrasonic measurement in laboratory tests gives a deeper insight into damage processes under cyclic loading. The results shall be used to improve design rules for concrete members under fatigue load and to develop or improve non-destructive techniques for in-service structural health monitoring.
The worldwide spread of windfarms brings new challenges, especially for concrete structures as a part of towers, connecting joints and foundations of wind turbines. High-cyclic loadings in such structures lead to a high relevance of the subject of fatigue. A proper assessment of the fatigue strength of concrete demands therefore a basis of reliable experimental data and the development of standardized testing methods. This article presents first results of an ongoing research program of BAM (Bundesanstalt für Materialforschung und -prüfung) which is a part of a joint project (WinConFat) funded by the German Federal Ministry for Economic Affairs and Energy. The subproject investigates the effects of size and slenderness of the specimens on the fatigue behaviour of high strength concrete at different stress levels. Not only the fatigue strength, but also the fatigue process itself is monitored by means of several measurement methods. Strain measurements are used to calculate the load dependent elastic modulus in the fatigue hysteresis as indicators for fatigue development. Furthermore, the application of non-destructive methods like acoustic emission analysis and ultrasonic measurement in laboratory tests gives a deeper insight into damage processes under cyclic loading. The results shall be used to improve design rules for concrete members under fatigue load and to develop or improve non-destructive techniques for in-service structural health monitoring.
Die heute in der Anwendung befindlichen Bemessungskonzepte für Ermüdung von Beton stammen zum Teil noch aus den 1990er Jahren und sind speziell hinsichtlich hochfester Betone konservativ ausgelegt. Um die Vorteile von Türmen für Windkraftanlagen, vor allem auch aus hochfesten Betonen, im Zuge des geplanten Ausbaus der Windenergieversorgung in Deutschland wirtschaftlich nutzbar zu machen, müssen diese Bemessungskonzepte weiterentwickelt werden. Dafür sind umfangreiche Untersuchungen zur Ermittlung von Bruchlastwechselzahlen und zur Charakterisierung der Schädigungsentwicklung unter Ermüdungsbeanspruchung erforderlich. Allgemein anerkannte bzw. verbindliche Regelwerke oder Verfahren zur experimentellen Bestimmung der Ermüdungsfestigkeit (Bruchlastwechselzahlen) an Betonproben gibt es zurzeit aber nicht und die bisher durchgeführten Untersuchungen variieren in Parametern wie Probengeometrie, Probengröße und Prüffrequenz. Eine vergleichende Analyse der Ergebnisse der Studien und insbesondere die Übertragbarkeit auf bauteilrelevante Abmessungen ist auf dieser Grundlage nur sehr eingeschränkt möglich.
Severe mechanical fatigue conditions for worldwide proliferating windfarms are a Major challenge for high-performance concrete in towers, connecting joints and foundations of wind turbines. High-performance concrete offers potential for the application in offshore windfarms, not only regarding its good mechanical, but also chemical resistivity due to low diffusivity in the highly densified microstructure. For a more reliable fatigue assessment, monitoring based on nondestructive testing can be a valuable complement to design rules. Both approaches demand reliable experimental data, information about scalability and the development of standardized testing methods. This article presents results of an ongoing research program of BAM (Bundesanstalt für Materialforschung und -prüfung), which is a part of a joint national project (WinConFat) funded by the German Federal Ministry for Economic Affairs and Energy. The subproject implemented by BAM examines the fatigue behavior in dependence of size and slenderness for varying concrete strength at different stress levels. Besides fatigue strength, nondestructive testing is carried out additionally.
Methods used are strain measurement and ultrasonic testing. The change of strain, stiffness and ultrasonic pulse velocity in the fatigue process is discussed. Results disclose a deeper insight into the damage process under cyclic loading of high-performance concrete and contribute to improve nondestructive monitoring.
The authors are currently investigating the possibility to apply compaction grouting for offshore pile foundations (Jacket piles as well as monopiles) as a possible retrofitting technique for an optimised foundation concept. In this research project, we are developing a design approach aiming to predict the ideal amount and properties of a grout for a specific soil situation and desired improvement of pile bearing capacity after Installation and during service time. Both numerical and experimental tests have been carried out to investigate the injection process during which a highly viscous grout is injected into the soil under high pressure to displace and compact the surrounding soil without fracturing it. The implicit Material Point Method (MPM) based on a mixed formulation is the numerical technique chosen to deal with the expected large deformations and the arbitrary shape of the developing grout bulb. The usage of MPM prevents both the need of remeshing and the numerical instability induced by extensive mesh distortion. For validation with experimental results, we have constructed a testing chamber with one transparent sidewall. This chamber enables us to observe the injection process directly at the transparent vertical window and to measure the in-plane soil displacements and strains by means of the Digital Image Correlation (DIC) technique.
The results already reveal the interrelation of soil and grout properties for a successful usage of this common ground improvement technique.
The increasing use of renewable energies leads to a constant search for optimised foundation concepts aiming to reduce the costs for offshore wind turbines. In an ongoing research project, we are developing a design approach for typical offshore driven piles based on the application of injections by compaction grouting directly at the pile shaft. Compaction grouting as a ground improvement technique has been used widely as a countermeasure against liquefaction, settlement and low bearing capacity of soil under new or already existing structures. It is performed by forcing highly viscous grout into the soil to displace and compact the surrounding soil without fracturing or penetrating it. Regarding this injection method, this paper gives a brief overview about general aspects such as appropriate soil characteristics and grouting parameters, grouting equipment and fields of application particularly in the offshore sector. This indicates the ability of our optimisation concept to provide an economic alternative to larger pile dimensions and a retrofitting technique, which is available during the entire lifetime of the foundation and can be deployed only in case of necessity (e.g. excessive deformations or insufficient structural stiffness after an extreme load event).
Besides the material feasibility and the constructive realisation of this improvement measure, the development of a corresponding verification concept is crucial in order to ensure the safety and durability of the retrofitted offshore piles. Here we will examine various verification concepts with their respective limitations in the framework of the limit state design. Furthermore, we will present the experimental findings from field tests in sand indicating the advantages of several local injections by compaction grouting for the enhancement of the load bearing behaviour of pile foundations. The test results were also used to validate a numerical model, developed with the finite element program PLAXIS, aiming to predict the expected bearing capacity for different injection scenarios (e.g. grout volume, location of injection points) along a pile shaft.
The aim of an ongoing research project is to develop a design approach for typical offshore driven piles (e.g. Jacket piles) based on the application of injections by compaction grouting directly at the pile shaft. The paper aims to present the results of laboratory and in-situ tests, which reveal the efficiency and the promising potential of the optimised foundation concept for a more economic dimensioning of pile foundations and to increase their bearing capacity in non-cohesive soil at any moment after installation.
Der Vortrag beschreibt die Relevanz der Zuverlässigkeitsbewertung von klassischen ZfP- und SHM-Verfahren. Diese Zuverlässigkeitsbewertung soll auch für das an der BAM entwickelte Risslumineszenzverfahren durchgeführt werden. Die Risslumineszenz wird zunächst vorgestellt und es wird beschrieben welchen Weg man beschreiten muss, um eine Zuverlässigkeitsbewertung für eine Technik durchzuführen, die nicht nur als ZfP-Verfahren genutzt werden soll, sondern auch für die Dauerüberwachung unter der Einbindung einer KI-basierten automatisierten Risserkennung. Die mit dieser Erweiterung des Einsatzspektrums einhergehenden Faktoren für Messunsicherheit und -variabilität wird als Problematik erkannt und als zukünftige Aufgabe, die es zu lösen gilt, definiert.
The new crack luminescence method offers the possibility of making fatigue surface cracks in metallic materials more visible during inspections through a special coating system. This coating system consists of two layers, whereby the first layer has fluorescent properties and emits visible light as soon as it is irradiated by UV light. The top layer is black and is designed to prevent the fluorescent layer from emitting if no crack develops in the underlying material.
The technique proved particularly useful in a wide variety of fatigue tests of steel components under laboratory conditions. Moreover, it has the potential to be used in various industrial applications. To enable industrial deployment and integration into maintenance strategies, a concept study is developed in this contribution, resulting in a qualification framework that can serve as a foundation for determining the reliability of the crack luminescence system in terms of a probability of detection curve. Within this study, factors causing measurement variability and uncertainty are being determined and their influences assessed. Due to the extension of the system by a moving computer vision system for automated crack detection using artificial intelligence, additional long-term effects associated with structural health monitoring systems need to be incorporated into an extended probability of detection study as part of the technical justification.
Finally, important aspects and findings related to design of experiments are discussed, and a framework for reliability assessment of a new optical crack monitoring method is presented, emphasizing the influence of various uncertainty parameters, including long-term effects such as system ageing.
The structural integrity of outer reinforced concrete (RC) containments of nuclear power plants provides an essential shield against external hazards. If this containment is damaged by an impact event, such as an aircraft crash, the question arises to which degree the reinforced concrete containment still has its protective capability. This concerns both purely structural protection and protection against liquids penetrating the interior of the containment. Due to the dimensions of the containment structures, it is difficult to perform real scale impact experiments, so in the past decades plate geometries at medium scale have been used for investigations. Detailed investigations on the structural behaviour of RC members or RC plates subjected to impact loading have already been presented in Just et al., Hering, Hering et al., Bracklow et al., Hille et al. and Nerger et al.
The following investigations deal with the single and multiple impact event (first hard impact and/or subsequent soft impact) on a RC specimen, which provides the basis for further investigations. A description of the test setup and the test procedure as well as a presentation of the test results from the impact tests are provided.
Furthermore, the experimental program is presented, which the damaged RC specimens are to undergo to deal with the question of how much the impact-damaged RC structure has become permeable to liquid media, such as water and kerosene, depending on the intensity of the impact. The aim of these following investigations is to develop a test setup that can be applied to investigate the liquid penetration behaviour (LPB) of small, medium, and large-scale RC members.
In addition to the liquid penetration experiments, the damaged specimens are to be examined by planar tomography to obtain the damage inside the specimen. The combination of damaging event, fluid penetration behaviour and tomography should enable a comprehensive understanding of the damage to the RC specimen.
The identification of the dynamic behavior of structures, like bridges and towers, is relevant to address multiple issues. In many cases the dynamic parameters should be acquired only once or at a frequency that doesn’t justify the installation of distinct vibration sensors for a long-term monitoring. To identify modal frequencies of a structure, a drone based mobile sensing platform has been implemented. This sensing platform measures the relative displacement be-tween the structure and the drone, which also shows a strong dynamic behavior under wind tur-bulences. By regarding the dynamic model of the drone and additional measurements at the dis-tance sensor the absolute movement of the structure can be estimated based on the measured relative distance. This time domain data is a suitable input for various operational modal analysis algorithms. The system has been used to identify the dynamic properties of test and real structure, like a 1.5 MW wind turbine tower.
At the Bundesanstalt für Materialforschung und -prüfung (BAM) full scale specimens for nuclear transport and storage containers (casks) are tested for their structural integrity in a series of drop tests on the Test Site Technical Safety in Horstwalde, 50 km south of Berlin. These drop tests cause a major stress not only on the casks, but also on the steel tower structure of the test facility, itself. The load pattern makes the structure very interesting for detailed investigation. The focus of the monitoring lies on the bolted joints of the flange connections that are a typical connection for cylindrical elements if welding is technical or economical unfavorable. The definition of the monitoring takes was done by investigating the existing documents and inspection results accompanied by building an initial digital representation of the structure, consisting of two finite element (FE) models and a geometrical 3D point cloud representation. As a first step the structures behavior during static and dynamic loading was analyzed using measurement data and an updated numerical FE Model. The idea behind is to use models for a digital planning and operation/evaluation of the structural health monitoring. A static FE simulation and a dynamic FE simulation are generated, to investigate how the structure behaves under the load conditions.
Mit der Errichtung und der Inbetriebnahme des Windpark alpha ventus wurden umfangreiche Messungen an den Tragstrukturen und den Umgebungsparametern durchgeführt. Im Projekt Gigawind life wurde im TP1 ein Datenmanagementsystem zur kontinuierlichen und periodisch fortgeführten Datenauswertung für große Datenbestände (Big Data) entworfen und realisiert. Anhand von Performanceuntersuchungen konnte eine Verkürzung der Rechenzeit um den Faktor 10 in einem Rechencluster erreicht werden. Unter Anwendung einer Datenpipeline nach dem Publish/Subscribe Prinzip wird eine skalierbare Datenschnittstelle für Monitoringdaten vorgeschlagen.
Der Vortrag stellt die Durchführung und die ersten Ergebnisse der Belastungsfahrten der BAM im Rahmen des AISTEC Projekts an der Maintalbrücke am 19.05. und 20.05.2021 vor. Es wurden Tragwerksreaktionen des Bauwerks mit dem installierten Dauermonitoringsystem und insbesondere dem Betongelenk mit zusätzlich installierter Sensorik aufgezeichnet. Für die Ermittlung der Lastposition wurden mehrere Verfahren eingesetzt und verglichen.
The long-term preservation of our infrastructure requires not only intelligent sensor technology and highly developed monitoring procedures, but also innovative digital tools for analyzing, evaluating and utilizing the results. This includes mathematical and, in particular, probabilistic methods for damage detection and tracking as well as for calculating service life and maintenance cycles and data management. The example project Maintal Bridge Gemuenden as part of the AISTEC project shows the workflow for the implementation of structural health monitoring and experimental tests with a train of Deutsche Bahn. The influence lines, as one possible way for damage detection, were measured with a highly accurate GNSS System to locate the trains position when crossing the bridge. The results were compared to measurements from 1987 just before the bridge went in operation.
At the Bundesanstalt für Materialforschung und -prüfung (BAM) full scale specimens for nuclear transport and storage containers (casks) are tested for their structural integrity in a series of drop tests on the Test Site Technical Safety in Horstwalde, 50 km south of Berlin. These drop tests cause a major stress not only on the casks, but also on the steel tower structure of the test facility, itself. The load pattern makes the structure very interesting for detailed investigation. The focus of the monitoring lies on the bolted joints of the flange connections that are a typical connection for cylindrical elements if welding is technical or economical unfavorable. The definition of the monitoring takes was done by investigating the existing documents and inspection results accompanied by building an initial digital representation of the structure, consisting of two finite element (FE) models and a geometrical 3D point cloud representation. As a first step the structures behavior during static and dynamic loading was analyzed using measurement data and an updated numerical FE Model. The idea behind is to use models for a digital planning and operation/evaluation of the structural health monitoring. A static FE simulation and a dynamic FE simulation are generated, to investigate how the structure behaves under the load conditions.
The identification of the dynamic behavior of structures, like bridges and towers, is relevant to address multiple issues. In many cases the dynamic parameters should be acquired only once or at a frequency that doesn’t justify the installation of distinct vibration sensors for a long-term monitoring. To identify modal frequencies of a structure, a drone based mobile sensing platform has been implemented. This sensing platform measures the relative displacement be-tween the structure and the drone, which also shows a strong dynamic behavior under wind tur-bulences. By regarding the dynamic model of the drone and additional measurements at the dis-tance sensor the absolute movement of the structure can be estimated based on the measured relative distance. This time domain data is a suitable input for various operational modal analysis algorithms. The system has been used to identify the dynamic properties of test and real structure, like a 1.5 MW wind turbine tower.