7.2 Ingenieurbau
Filtern
Dokumenttyp
- Vortrag (161)
- Beitrag zu einem Tagungsband (81)
- Zeitschriftenartikel (61)
- Posterpräsentation (10)
- Buchkapitel (4)
- Dissertation (4)
- Beitrag zu einem Sammelband (3)
- Tagungsband (Herausgeberschaft für den kompletten Band) (1)
- Sonstiges (1)
Sprache
- Englisch (246)
- Deutsch (79)
- Mehrsprachig (1)
Schlagworte
- Structural Health Monitoring (25)
- Ground vibration (20)
- Structural health monitoring (15)
- Fatigue (14)
- Brücken (11)
- Monitoring (11)
- Offshore (11)
- Offshore wind energy (11)
- Hammer impact (9)
- Impact (9)
- Train passage (9)
- Damage characterization (8)
- Model interpolation (8)
- Planar tomography (8)
- Structural systems (8)
- Vibration measurements (8)
- Building vibration (7)
- Damage detection (7)
- Deterioration (7)
- Layered soil (7)
- Reliability (7)
- Slab track (7)
- Soil-structure interaction (7)
- Train-induced ground vibration (7)
- Bahnerschütterungen (6)
- Compressive strength (6)
- Design methods (6)
- Grout (6)
- Inspection (6)
- Numerical modelling (6)
- Offshore wind turbines (6)
- Physical phenomenology (6)
- Pile foundations (6)
- Reinforced concrete structure (6)
- SHM (6)
- Environmental effects (5)
- Interface (5)
- Layered soils (5)
- Modalanalyse (5)
- Numeric simulation (5)
- Repair (5)
- Temperature rejection (5)
- Ultrasonic testing (5)
- Vibration (5)
- Bayesian updating (4)
- Container loading (4)
- Crack detection (4)
- Damage localization (4)
- Datenmanagement (4)
- Drop test (4)
- Erosion (4)
- Erschütterungen (4)
- Erschütterungsminderung (4)
- Excitation forces (4)
- Fault detection (4)
- Foundation load (4)
- Foundations (4)
- Gründungsstrukturen (4)
- High-strength concrete (4)
- Inspection planning (4)
- Mitigation (4)
- Offshore geomechanics (4)
- Shell Buckling (4)
- Statistical tests (4)
- Steel structures (4)
- Subspace methods (4)
- Subspace-based method (4)
- Tunnel (4)
- Vehicle-track-soil interaction (4)
- Vibration measurement (4)
- Wind (4)
- Wind Energy (4)
- Windenergie (4)
- Ansys Autodyn (3)
- Attenuation (3)
- Axle impulses (3)
- BIM (3)
- Bauwerksüberwachung (3)
- Belastungsversuch (3)
- Box-Behnken (3)
- Bridge (3)
- Bridges (3)
- Buckling (3)
- Compaction Grouting (3)
- Cracks (3)
- DUCON® (3)
- Deep foundations (3)
- Dispersionsmessung (3)
- Drucker-Prager (3)
- Ductility (3)
- E-modulus (3)
- Earth masonry (3)
- Elastische Gleiselemente (3)
- Emission (3)
- Erschütterungsprognose (3)
- Filter effects (3)
- Fly ash (3)
- Grouted connection (3)
- Grouting (3)
- Großer Fallturm Horstwalde (3)
- Irregular soil (3)
- Leichtbau (3)
- Linear parameter varying systems (3)
- Load vector (3)
- Maintenance (3)
- Material moisture (3)
- Metakaolin (3)
- Micro-reinforcement (3)
- Micromechanical modelling (3)
- Mobile elements (3)
- Monopiles (3)
- Numerical modeling (3)
- Offshore Pile Foundation (3)
- Offshore Windenergieanlagen (3)
- Offshore foundations (3)
- Physical testing (3)
- Post-impact evaluation (3)
- Probabilistic (3)
- Quasi-static and dynamic tests (3)
- Railway (3)
- Railway bridge (3)
- Randomly heterogeneous soil (3)
- Rehabilitation (3)
- Reinforced concrete (3)
- Risk (3)
- Scattering (3)
- Schwingungsdynamik (3)
- Soil erosion (3)
- Statistical evaluation (3)
- Statistical method (3)
- Stereo photogrammetry (3)
- Subspace-based residual (3)
- Temperature effects (3)
- Train speed (3)
- UHPC (3)
- Vehicle-track interaction (3)
- Vibrations (3)
- Wellengeschwindigkeit (3)
- Zivile Sicherheit (3)
- 2-span bridge (2)
- AISTEC (2)
- Acceleration sensors (2)
- Achsfolgespektren (2)
- Acoustic emission testing (2)
- Amplitude-charge weight laws (2)
- Amplitude-distance laws (2)
- Analysis of variance (2)
- Apartment building (2)
- Artificial Intelligence (2)
- Artificial intelligence (2)
- Automatisierte schweißtechnische Fertigung (2)
- Axle sequence (2)
- Axle-sequence spectrum (2)
- Ballast track (2)
- Bauteile (2)
- Bauwerke (2)
- Bauwerksmonitoring (2)
- Bayes'sche Analyse (2)
- Bayesian System Identification (2)
- Bayesian analysis (2)
- Bayesian methods (2)
- Bayesian system identification (2)
- Bemessung (2)
- Big Data (2)
- Bitumen (2)
- Bodenübertragungsfunktion (2)
- Brücke (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Changing process noise (2)
- Chemisoprtion (2)
- Climate chamber (2)
- Compressive Cyclic loading (2)
- Compressive cyclic loading (2)
- Computer Vision (2)
- Concrete (2)
- Coupler systems (2)
- Crack Luminescence (2)
- Crack formation (2)
- Crack pattern (2)
- Cyclic load (2)
- DEM (2)
- Damage identification (2)
- Design (2)
- Digital twin (2)
- Digitalisierung (2)
- Displacements (2)
- Drone (2)
- Earth block masonry (2)
- Elastische Elemente (2)
- Elastische Gebäudelagerung (2)
- Energy (2)
- Erschütterungsausbreitung (2)
- Evaluation (2)
- Explosion-induced ground vibrations (2)
- Faseroptik (2)
- Feuchte (2)
- Finite Elemente Simulation (2)
- Finite element models (2)
- Freight train (2)
- GPU parallel computation (2)
- Gleiströge (2)
- Ground vibration measurements (2)
- Grouted Connection (2)
- Halbraum (2)
- High-speed (2)
- High-speed train (2)
- Immission (2)
- Injection Sequence (2)
- Irregular ballast (2)
- Irregularities (2)
- Jacket support structure (2)
- Jet erosion test (2)
- Klimakammer (2)
- Knudsen effect (2)
- LBM-DEM (2)
- Laboratory beam structure (2)
- Lehm (2)
- Long-term shrinkage (2)
- Luminescence (2)
- Macromechanical Sample Strength (2)
- Material tests (2)
- Mauerwerk (2)
- Measurement (2)
- Measurements (2)
- Messen im Bauwesen (2)
- Micro silica (2)
- Micromechanical Tensile Failure (2)
- Mix design (2)
- Modal Analysis (2)
- Model updating (2)
- Moisture (2)
- Moisture content (2)
- Molecular diffusion (2)
- Non destructive testing (2)
- Non-Destructive Evaluation (2)
- Non-destructive testing (2)
- Numerical model (2)
- Office tower (2)
- Offshore Wind Energy (2)
- Offshore geotechnics (2)
- Offshore wind (2)
- Offshore-Windenergieanlagen (2)
- Optimal Sensor Placement (2)
- Passenger train (2)
- Physisorption (2)
- Pile Foundation (2)
- Pile Tip Buckling (2)
- Prediction (2)
- Prediction of explosion induced ground and building vibration (2)
- Probability of Detection (2)
- Prädiktive Instandhaltung (2)
- Radar (2)
- Railway tunnel (2)
- Railways (2)
- Rechenmodelle (2)
- Reinforcement (2)
- Relative humidity (2)
- Research data management (2)
- Residual evaluation (2)
- Resonance (2)
- Risslumineszenz (2)
- SDDLV (2)
- Safety (2)
- Scattered axle impulses (2)
- Schadensdetektion (2)
- Schwingungsbasierte Verfahren (2)
- Size effect (2)
- Slenderness effect (2)
- Soil properties (2)
- Soil-Structure-Interaction (2)
- Soil-pile interaction (2)
- Soil-wall-floor model (2)
- Static axle loads (2)
- Static load (2)
- Strength (2)
- Strukturmonitoring (2)
- Supplementary cementitious materials (2)
- Surface-tunnel reduction (2)
- System Identification (2)
- System identification (2)
- Tensile Capacity (2)
- Time-variant reliability (2)
- Tomographic damage evaluation (2)
- Track damage (2)
- Track-soil interaction (2)
- Train excitation (2)
- Transmission (2)
- Umwelteinflüsse (2)
- Uncertainty (2)
- Uncertainty in reference (2)
- Uncertainty quantification (2)
- Unterraummethoden (2)
- Value of Information (2)
- Vehicle–track interaction (2)
- Vollraum (2)
- Wellenausbreitung (2)
- Wellenausbreitung in der Tiefe (2)
- Wind Turbines (2)
- Wind energy (2)
- Wind turbine tower (2)
- Windenergieanlagen (2)
- Windenergy (2)
- Zuggeschwindigkeit (2)
- Zuverlässigkeit (2)
- 3D imaging (1)
- Achsimpulse (1)
- Acoustic emission (1)
- Acoustic emission analysis (1)
- Ambient excitation (1)
- Amplituden-Abstands-Gesetze (1)
- Analytical Design Methods (1)
- Asphalt (1)
- Assessment (1)
- Asymptotic local approach (1)
- Automated Modal Analysis for Tracking Structural Change during Construction and Operation Phases (1)
- Automated operational modal analysis (1)
- Automatic modal parameters identification (1)
- Automatisierte Fertigung (1)
- Automatisierte schweißtechniche Fertigung (1)
- Autonomous underwater vehicles (1)
- Axial load bearing (1)
- Axle loads (1)
- Axle pulses (1)
- BAM Windenergie Fügetechnik (1)
- Bahngleis (1)
- Base isolation (1)
- Baugrunddynamik (1)
- Bauwerk-Boden-Wechselwirkung (1)
- Bauwerksdiagnostik (1)
- Beanspruchungszustand (1)
- Belastungsfahrt (1)
- Belastungstest (1)
- Belastungszug (1)
- Benchmark (1)
- Beton (1)
- Betonautobahn (1)
- Betonautobahnen (1)
- Beulen (1)
- Bewertung (1)
- Bionik (1)
- Blast (1)
- Blast tests (1)
- Bodenschlitz (1)
- Bodenvariabilität (1)
- Boundary element (1)
- Boundary element method (1)
- Bridge monitoring (1)
- Bridge resonance (1)
- Bridge vibration (1)
- Bruchlastwechselzahlen (1)
- Brückensicherheit (1)
- Buckling piles circular shells (1)
- Buckling soil-structure-interaction offshore piles track (1)
- Building and Construction (1)
- Building information modelling (1)
- Building response (1)
- CFD (1)
- Cancellation (1)
- Cars (1)
- Cement-based composites (1)
- Chemisorption (1)
- Civil and Structural Engineering (1)
- Civil structures (1)
- Climate Chamber (1)
- Coating (1)
- Cohesive granular materials (1)
- Cohesive soils (1)
- Column/wall resonance (1)
- Combined finite-element boundary-element method (1)
- Compaction grouting (1)
- Compliance function (1)
- Components of excitation (1)
- Compression tests (1)
- Computational (1)
- Condensed Matter Physics (1)
- Conductor (1)
- Continuous soil (1)
- Continuously inhomogeneous geological media (1)
- Continuously inhomogeneous soils (1)
- Crack (1)
- Crack damage detection (1)
- Crack repair (1)
- Cyber security (1)
- Cyclic axial shearing (1)
- Cyclic degradation (1)
- DEM-LBM simulation (1)
- Damage Detection (1)
- Damage evolution (1)
- Decision matrix analysis (1)
- Deckeneigenfrequenzen (1)
- Deckenschwingungen (1)
- Design models (1)
- Design practice (1)
- Detection (1)
- Digital Image Correlation (1)
- Digital Image Correlation (DIC) (1)
- Digital Models (1)
- Digital Twin (1)
- Digitale Zwillinge (1)
- Discrete Element Method (1)
- Discrete element method (1)
- Drop Test (1)
- Drop Tests (1)
- Drop tower (1)
- Druckfestigkeit (1)
- Druckschwellenversuch (1)
- Dynamic axle loads (1)
- Dynamic loads (1)
- Dynamic soil properties (1)
- Dynamische Bodenkennwerte (1)
- Dynamische Bodensteifigkeit (1)
- Dämpfung (1)
- EERA Joint Program (1)
- Earth (1)
- Earth blocks (1)
- Earth material (1)
- Earthen hydraulic constructions (1)
- Earthen hydraulic infrastructures (1)
- Einflusslinie (1)
- Einflusslinien (1)
- Einfügungsdämmung (1)
- End-of-life decision making (1)
- Entscheidungsfindung (1)
- Environmental (1)
- Environmental Effects (1)
- Environmental changes (1)
- Environmental influence (1)
- Erhaltungsmanagement (1)
- Ermüdung (1)
- Ermüdungsprüfung (1)
- Ermüdungsschäden (1)
- Ermüdungsverhalten (1)
- Erneuerbare Energien (1)
- Erosion of cohesive soils (1)
- Erschütterungen im Fernfeld (1)
- Estimation (1)
- FEM (1)
- FEM analysis (1)
- Fahrzeug-Fahrweg-Boden-Wechselwirkung (1)
- Fallturm (1)
- Fatigue damage (1)
- Fatigue deterioration (1)
- Fatigue strength (1)
- Fault detectionchanging (1)
- Features (1)
- Fequency domain (1)
- Fiber optic sensing (1)
- Fibre optic sensors (1)
- Finite element (1)
- Finite element analysis (1)
- Finite element method (1)
- Finite element model updating (1)
- Finite elements (1)
- Finite-Elemente-Modellkalibrierung (1)
- Finite-element boundary-element method (1)
- Flexibility (1)
- Flexible car body (1)
- Flexible wheelset (1)
- Floor resonance (1)
- Floors (1)
- Fluid-structure interaction (1)
- Footbridge (1)
- Force reconstruction (1)
- Foundation Pile (1)
- Foundation reliability analysis (1)
- Freileitung (1)
- Frequency response function (1)
- GMNIA (1)
- GNSS (1)
- GPA (1)
- GPU Parallel computing (1)
- GPU parallelisation (1)
- Gebäudelagerung (1)
- Gebäudemodelle (1)
- Gebäudeschwingungen (1)
- General Materials Science (1)
- Geology (1)
- Geomechanics (1)
- Geomechanics of offshore foundations (1)
- Geometric vehicle and track irregularities (1)
- Geometrie (1)
- Global ambient vibrations (1)
- Granular Cohesive Materials (1)
- Granular Cohesive Materials, (1)
- Granular cohesion (1)
- Ground (1)
- Grout Injection (1)
- HAZID (1)
- HTLS (1)
- Hard impact (1)
- Harter Anprall an Stahlbetonstrukturen (1)
- High-Rise Building (1)
- High-rise building (1)
- High-rise buildings (1)
- Horizontal stress (1)
- Horizontal wind turbine (1)
- Hydraulic jet erosion (1)
- IEPE (1)
- Impact damage of reinforced concrete (1)
- Impact damage on reinforced concrete (1)
- Impact loading (1)
- Impakt (1)
- Impedanzmethode (1)
- Imperfektion (1)
- Impinging jet (1)
- Inclination angle (1)
- Inertial Interaction (1)
- Inertial interaction (1)
- Inhomogeneous soils (1)
- Innovative Messtechnik (1)
- Inspeciton (1)
- Inspektion (1)
- Interface model (1)
- Jet impingement (1)
- Kinematic Interaction (1)
- Kinematic interaction (1)
- Kraft auf den Boden (1)
- LBM-DEM coupling (1)
- LBM-DEM simulation (1)
- Laminar flow (1)
- Laminography (1)
- Large components (1)
- Lateral dynamic displacement (1)
- Lateral load bearing (1)
- Lattice Boltzmann Method (1)
- Lattice Boltzmann method (1)
- Leichtbauprinzipien (1)
- Load Test (1)
- Load bearing behaviour (1)
- Load identification (1)
- Load tests (1)
- Load-bearing (1)
- Load-bearing behaviour (1)
- Local approaches (1)
- Long-span bridge (1)
- Low-frequency shaker (1)
- MEMS (1)
- Maintal Bridge Gemuenden (1)
- Maintalbrücke Gemünden (1)
- Marine geomechanics (1)
- Marine geotechnics (1)
- Maschinenbetrieb (1)
- Material Point Method (1)
- Material Point Method (MPM) (1)
- Material model (1)
- Measurement campaigns (1)
- Mechanical challenges (1)
- Merkblatt (1)
- Messfahrt (1)
- Microfine Cement (1)
- Microfine cement (1)
- Micromechanical LBM-DEM simulation (1)
- Micromechanical analysis (1)
- Micromechanical simulation (1)
- Microsilica (1)
- Minderungsmaßnahmen (1)
- Mixed formulation (1)
- Modal analysis (1)
- Modal force spectrum (1)
- Modal load spectrum (1)
- Modal system identification (1)
- Model Update (1)
- Model update (1)
- Modell-Update (1)
- Modellierung (1)
- Modes (1)
- Modes and waves (1)
- Modulus of elasticity (1)
- Monitoring-informed inspection and maintenance planning (1)
- Monopile (1)
- Monopile Buckling (1)
- Monopile installation risks (1)
- Movin load test (1)
- Multi-beam method (1)
- Multi-beam track model (1)
- Multiple impact (1)
- Nachgiebigkeiten (1)
- Nelson’s method (1)
- Normung (1)
- Numerical analysis (1)
- Numerical damage simulation (1)
- Numerical simulation of impact damage (1)
- Numerical simulations (1)
- Obstacles (1)
- Offhore (1)
- Office building (1)
- Offshore Structures (1)
- Offshore Wind (1)
- Offshore Wind Energy Converter (1)
- Offshore Windenergie (1)
- Offshore pile foundation (1)
- Offshore pile foundations (1)
- Offshore steel structures (1)
- Offshore wind energy foundations (1)
- Offshore wind farm (1)
- Offshore wind farms (1)
- Offshore wind turbine (1)
- Offshore wind-turbine foundations (1)
- Offshore-Wind (1)
- Operational modal analysis (1)
- Optimal sensor placement (1)
- Optimierungsmethoden (1)
- Optimization techniques (1)
- Perfectly Matched Layer (PML) (1)
- Pfahlfußbeulen (1)
- Pfahlnachgiebigkeiten (1)
- Physisoprtion (1)
- Piaui state (1)
- Pile Buckling (1)
- Pile Capacity (1)
- Pile ageing (1)
- Pile bending stiffness (1)
- Pile foundation (1)
- Pile groups (1)
- Pile retrofit system (1)
- Pile-Tip-Buckling (1)
- Point Cloud (1)
- Predictive maintenance (1)
- Pressure (1)
- Probabilistic modelling (1)
- Probabilitische Ingenieurmodelle (1)
- Probability of detection (1)
- Probekörpergeometrien (1)
- Process noise (1)
- Prognose (1)
- Propagation from a tunnel (1)
- Quasi-static response; (1)
- Rail roughness (1)
- Railbridge (1)
- Railway induced vibration (1)
- Railway track (1)
- Railway tracks (1)
- Railway trafiic (1)
- Randelementmethode (1)
- Random dynamics and vibrations (1)
- Random stiffness variation (1)
- Rayleighwellendispersion (1)
- Rechenverfahren (1)
- Recovery experiments (1)
- Remote sensing vibrometer (1)
- Repowering (1)
- Residential building (1)
- Richtige Fahrzeugmasse (1)
- Richtlinie (1)
- Rigid vehicle model (1)
- Risiko (1)
- Risikoanalyse (1)
- Risk-based design (1)
- Risk-based maintenance planning (1)
- Rissprozes (1)
- Rissprozess (1)
- Road bridges (1)
- SHCC (1)
- SHM Environmental (1)
- SHM environmental bridges (1)
- Sandstone (1)
- Santa-marta (1)
- Scaling (1)
- Schadensüberwachung (1)
- Scherwellengeschwindigkeit (1)
- Schienenfahrweg (1)
- Schienenfahrwege (1)
- Schrauben (1)
- Schubmodul (1)
- Schwingungsmessungen (1)
- Schwingungsmonitoring (1)
- Schädigungsprozesse (1)
- Sensitivity vectors (1)
- Serra da cangalha (1)
- Shearing (1)
- Shell buckling (1)
- Shrinkage (1)
- Shrinkage Reducing Admixture (1)
- Sicherheit (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Simulation and experiment (1)
- Site-characterization (1)
- Soft impact (1)
- Soft track elements (1)
- Soil Struture Interaction (1)
- Soil forces (1)
- Soil stiffness (1)
- Soil-building interaction (1)
- Soil-building resonance (1)
- Soil-wall floor model (1)
- Soil-water-structure interaction (1)
- Sorption isotherm (1)
- Spatially varying ground conditions (1)
- Spektralanalyse (1)
- Stability Buckling soil-structure-interaction piles offshore (1)
- Stabilität (1)
- State of stress (1)
- Static loading (1)
- Statistical correlations (1)
- Statistical pattern recognition (1)
- Statistische Auswertung (1)
- Statistische Korrelationen (1)
- Stiffness variation (1)
- Stochastic Subspace Damage Detection (1)
- Strain (1)
- Stress stiffening (1)
- Stress-strain relation (1)
- Stress–strain-relation (1)
- Structural Systems (1)
- Structural integrity (1)
- Structural integrity maintenance (1)
- Structural integrity management (1)
- Structural system identification (1)
- Störgrößen (1)
- Substructures (1)
- Superplasticizer (1)
- Supplementary Cementitious Materials (1)
- Support structures (1)
- Surface Foundation (1)
- Surface line (1)
- Sustainable binders (1)
- Switch (1)
- Systemidentifikation (1)
- TOP (1)
- TRC (1)
- Tagung (1)
- Temperature effect (1)
- Temperature effect rejection (1)
- Temperature modeling (1)
- Temperatureinflüsse (1)
- Tensile test (1)
- Test specification (1)
- Tip Buckling (1)
- Track and vehicle irregularities (1)
- Track beam (1)
- Track damage monitoring (1)
- Track damage quantification (1)
- Track deflection (1)
- Track displacements (1)
- Track filter (1)
- Track filtering (1)
- Track vibration (1)
- Tragfähigkeit (1)
- Tragstrukturen (1)
- Train configuration (1)
- Train passages (1)
- Train-induced vibration (1)
- Tran speed (1)
- Transfer fuction (1)
- Transfer function (1)
- Transverse butt weld (1)
- Trench (1)
- Truss structures (1)
- Tunnel line (1)
- Tunnel-pile transfer (1)
- Tunnel-to-surface reduction (1)
- Tunnelstrecke (1)
- Turnout (1)
- UAS (1)
- Un- certainty (1)
- Unbounded domain (1)
- Under-sleeper pads (1)
- Value of information (1)
- Variational Bayesian statistics (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Varying track stiffness (1)
- Vibration analysis (1)
- Vibration excitation (1)
- Vibration monitoring (1)
- Viscosity (1)
- Vorspannung (1)
- Wahrscheinlichkeit (1)
- Water Science and Technology (1)
- Water-structure interaction (1)
- Wave-Tower interaction (1)
- Wavenumber domain (1)
- Wavenumber integrals (1)
- Wavenumber method (1)
- Waves (1)
- Weld imperfections (1)
- Wellenfeldberechnung (1)
- Wheelset (1)
- Wheelset accelerations (1)
- Wind Energy Structures (1)
- Wind energy tower (1)
- Wind turbines (1)
- Wind-farm aerodynamics (1)
- Windenergieanlage (1)
- Windfarm wake analysis (1)
- Workability (1)
- Zerstreute Achsimpulse (1)
- building information modelling (1)
- elastische Gebäudelagerungen (1)
- fachwerkartige Stahltragwerken (1)
- layered soil (1)
- risk, reliability, inspection planning, offshore wind turbines (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- temperature (1)
- zerstreute Achslastimpulse (1)
- Übertragungsmatrizen (1)
- Überwachung (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (326) (entfernen)
Paper des Monats
- ja (4)
In this article, a partial selection of experiments on enhancing the impact resistance of structural components with non-metallic, textile-reinforced concrete is discussed. The focus is on the experimental investigations in which the impact resistance of thin, textile-reinforced concrete plates is characterized. The article discusses the materials, fabrics and test setup used. For the experimental work, a drop tower from the Otto Mohr Laboratory, which belongs to the Technische Universtät Dresden, was used. Furthermore, the experimental results are presented and evaluated using different methods. Based on the collected data, a suitable approach to determining the perforation velocity of an impactor through the investigated thin, textile-reinforced concrete plates is shown.
Die heute in der Anwendung befindlichen Bemessungskonzepte für Ermüdung von Beton stammen zum Teil noch aus den 1990er Jahren und sind speziell hinsichtlich hochfester Betone konservativ ausgelegt. Um die Vorteile von Türmen für Windkraftanlagen, vor allem auch aus hochfesten Betonen, im Zuge des geplanten Ausbaus der Windenergieversorgung in Deutschland wirtschaftlich nutzbar zu machen, müssen diese Bemessungskonzepte weiterentwickelt werden. Dafür sind umfangreiche Untersuchungen zur Ermittlung von Bruchlastwechselzahlen und zur Charakterisierung der Schädigungsentwicklung unter Ermüdungsbeanspruchung erforderlich. Allgemein anerkannte bzw. verbindliche Regelwerke oder Verfahren zur experimentellen Bestimmung der Ermüdungsfestigkeit (Bruchlastwechselzahlen) an Betonproben gibt es zurzeit aber nicht und die bisher durchgeführten Untersuchungen variieren in Parametern wie Probengeometrie, Probengröße und Prüffrequenz. Eine vergleichende Analyse der Ergebnisse der Studien und insbesondere die Übertragbarkeit auf bauteilrelevante Abmessungen ist auf dieser Grundlage nur sehr eingeschränkt möglich.
The contribution shows measurement examples of cars, floors, foundations, railway tracks, a footbridge, and a railbridge. Vibrations may include modes and waves. Namely in soil-structure interaction, modes are damped, shifted and prevented so that alternatives for the modal analysis are necessary: The approximation of the whole spectrum (flexibility function) and of the whole train passage (moving-load response).
Die Prognose und Minderung von Bahnerschütterungen haben eine lange Tradition in der Bundesanstalt für Materialforschung und -prüfung. Im Jahr 2006 wurde eine Prognose-Software fertiggestellt, die viele Forschungs- und Messergebnisse zusammenfasst. Sie umfasst die Teilbereiche Emission (die Anregung durch die Fahrzeug-Fahrweg-Untergrund-Wechselwirkung), die Transmission (die Ausbreitung durch den Boden) und die Immission (die Übertragung vom Freifeld in ein Gebäude). Die Prognose geschieht in allen Teilen mit einfachen Formeln, die veröffentlicht sind und zur Anwendung für Jedermann zur Verfügung stehen. Es werden Beispiele zur Emission und zur Transmission gezeigt.
Im Bereich Transmissionsprognose werden zu den Anregungskräften (aus dem Emissionsteil) die Bodenerschütterungen als Schwinggeschwindigkeitsterzspektren berechnet. Das Ergebnis hängt stark von der Bodensteifigkeit, -dämpfung und -schichtung ab. Dies wurde später mit einer Messkampagne in der Schweiz an 10 Messorten bestätigt (Bild 1). Die Berechnung erfolgt näherungsweise für einen geschichteten Boden mit einer frequenzabhängigen Wellengeschwindigkeit (Dispersion) oder einem tiefenabhängigen Wellengeschwindigkeitsprofil.
Die Anregungskräfte werden im Prognosebereich Emission mit einem 2-dimensionalen Gleismodell berechnet (Bild 2). 1-dimensionale Modelle liefern meist falsche Ergebnisse und 3-dimensionale Modelle (zum Beispiel mit der kombinierten Finite-Element-Randelement-Methode) sind für eine Erschütterungs¬prognose sicherlich zu aufwändig. Das 2-dimensionale Modell wurde an 3-dimensionale Ergebnisse so angepasst, dass die Ergebnisse für viele Gleise und Böden annähernd zutreffen. Auch Minderungs¬maßnahmen am Gleis können mit diesem Modell sehr gut berechnet werden.
Die Prognoseverfahren wurden in den folgenden Jahren weiter verfeinert. Es wurde die quasi-statische Anregung durch die bewegten statischen Zuglasten mit einer Näherungsformel ergänzt, so dass auch das tieffrequente Nahfeld realistisch erfasst werden kann. Mit der Berücksichtigung der Achsfolge (insbesondere zwischen den Achsen im Drehgestell) ergeben sich zwei typische Minima in den Erschütterungsspektren, die oft auch in den Messungen beobachtet werden. Der Amplitudenanteil zwischen diesen beiden Minima ist oft stärker angehoben, so dass hier eine zusätzliche Erschütterungsanregung vermutet wird. Dieser Anteil kann rein empirisch prognostiziert werden, so wie das in den englischen Prognosen (zuletzt für das Highspeed2-Projekt) enthalten ist. Die Begründung dieses Anteils ist allerdings nicht die Achsfolge, sondern die Zerstreuung der statischen Achslastimpulse durch einen unregelmäßigen Gleisuntergrund und Boden.
Die messtechnische Ermittlung eines Minderungseffektes ist komplizierter als allgemein angenommen. Es reicht nicht aus, jeweils an einem Messpunkt in der Nähe eines Gleises mit und ohne Minderungs¬maßnahme die Erschütterungen zu messen und aus dem Verhältnis der Amplituden (beziehungsweise aus der Differenz der Pegel) „die Einfügedämmung“ zu ermitteln. Es wird an Beispielen gezeigt, wie man hier sinnvoller vorgehen kann.
1. Zunächst ist es wichtig, nicht nur die Einfügedämmung sondern auch die Originalspektren mit und ohne Minderung zu dokumentieren und zu veröffentlichen, damit man kontrollieren kann, ob wesentliche Amplituden und Frequenzbereiche reduziert sind oder ob es sich um eher zufällige Minderungen oder Verstärkungen handelt. (Beispiel Unterschottermatte/Raron, Müller/SBB)
2. Der Messpunkt sollte nicht im Nahbereich des Gleises liegen, da ansonsten eine zu günstige, falsche Einfügedämmung bestimmt wird. (Beispiel Tunnel/ Leipzig/Breitsamter)
3. Um Zufälligkeiten zu vermeiden, sollte man an mehr als einem Punkt messen. (Beispiel Unterschotterplatte/Altheim/Auersch)
4. Man sollte eigentlich immer auch die Bodenkennwerte (Steifigkeit, Dämpfung, Amplituden-abnahme, Übertagungsfunktion) messen. Selbst bei nahegelegene Messquerschnitten kann man Überraschungen erleben. (Beispiel erste ICE-Messungen/bei Würzburg/Auersch)
5. Bei verschiedenen Bodenkennwerten kann man eine Korrektur durchführen. (Beispiel Gleis-tröge/Mistler) Am besten bestimmt man ein äquivalentes Kraftspektrum zu jedem Messort und jedem Messzug (Beispiel Feste Fahrbahn/Gardelegen/Auersch)
6. Prinzipiell gibt es nicht die Einfügedämmung einer Maßnahme. Die Einfügedämmung ist immer boden- und referenzsystemabhängig. Die „beste“ Einfügungsdämmung erhält man mit einem steifen Untergrund (Beispiel Unterschottermatte/Tunnel/München Gasteig/Wettschureck) Das heißt aber nicht, dass die Maßnahme durch einen künstlich versteiften Untergrund besser wird (Beispiel Unterschottermatten/RRT2006/Auersch)
Es werden Messbeispiele gezeigt, die alle neben einer hochfrequenten dynamischen Minderung auch eine mittelfrequente quasi-statische Minderung aufweisen. Dabei wird der mittelfrequente Zerstreuanteil der statischen Achslastimpulse durch die breitere Lastverteilung und damit die Impulsdehnung der Achslastimpulse reduziert. Diese Impulsdehnung lässt sich mit dem 2-dimensionalen Gleismodell berechnen. Die Minderungswirkung hängt aber wiederum vom Referenzsystem und dessen unregel¬mäßiger Steifigkeitsverteilung ab. Je unregelmäßiger der Boden und Gleisuntergrund des Referenz¬systems, desto stärker ist die Minderungswirkung.
Die Prognose und Minderung von Bahnerschütterungen haben eine lange Tradition in der Bundesanstalt für Materialforschung und -prüfung. Im Jahr 2006 wurde eine Prognose-Software fertiggestellt, die viele Forschungs- und Messergebnisse zusammenfasst. Sie umfasst die Teilbereiche Emission (die Anregung durch die Fahrzeug-Fahrweg-Untergrund-Wechselwirkung), die Transmission (die Ausbreitung durch den Boden) und die Immission (die Übertragung vom Freifeld in ein Gebäude). Die Prognose geschieht in allen Teilen mit einfachen Formeln, die veröffentlicht sind und zur Anwendung für Jedermann zur Verfügung stehen. Es werden Beispiele zur Emission und zur Transmission gezeigt. Im Bereich Transmissionsprognose werden zu den Anregungskräften (aus dem Emissionsteil) die Bodenerschütterungen als Schwinggeschwindigkeitsterzspektren berechnet. Das Ergebnis hängt stark von der Bodensteifigkeit, -dämpfung und -schichtung ab. Dies wurde später mit einer Messkampagne in der Schweiz an 10 Messorten bestätigt. Die Berechnung erfolgt näherungsweise für einen geschichteten Boden mit einer frequenzabhängigen Wellengeschwindigkeit (Dispersion) oder einem tiefenabhängigen Wellengeschwindigkeitsprofil. Die Anregungskräfte werden im Prognosebereich Emission mit einem 2-dimensionalen Gleismodell berechnet. 1-dimensionale Modelle liefern meist falsche Ergebnisse und 3-dimensionale Modelle (zum Beispiel mit der kombinierten Finite-Element-Randelement-Methode) sind für eine Erschütterungs¬prognose sicherlich zu aufwändig. Das 2-dimensionale Modell wurde an 3-dimensionale Ergebnisse so angepasst, dass die Ergebnisse für viele Gleise und Böden annähernd zutreffen. Auch Minderungs¬maßnahmen am Gleis können mit diesem Modell sehr gut berechnet werden. Die Prognoseverfahren wurden in den folgenden Jahren weiter verfeinert. Es wurde die quasi-statische Anregung durch die bewegten statischen Zuglasten mit einer Näherungsformel ergänzt, so dass auch das tieffrequente Nahfeld realistisch erfasst werden kann. Mit der Berücksichtigung der Achsfolge (insbesondere zwischen den Achsen im Drehgestell) ergeben sich zwei typische Minima in den Erschütterungsspektren, die oft auch in den Messungen beobachtet werden. Der Amplitudenanteil zwischen diesen beiden Minima ist oft stärker angehoben, so dass hier eine zusätzliche Erschütterungsanregung vermutet wird. Dieser Anteil kann rein empirisch prognostiziert werden, so wie das in den englischen Prognosen (zuletzt für das Highspeed2-Projekt) enthalten ist. Die Begründung dieses Anteils ist allerdings nicht die Achsfolge, sondern die Zerstreuung der statischen Achslastimpulse durch einen unregelmäßigen Gleisuntergrund und Boden. Die messtechnische Ermittlung eines Minderungseffektes ist komplizierter als allgemein angenommen. Es reicht nicht aus, jeweils an einem Messpunkt in der Nähe eines Gleises mit und ohne Minderungsmaßnahme die Erschütterungen zu messen und aus dem Verhältnis der Amplituden (beziehungsweise aus der Differenz der Pegel) „die Einfügedämmung“ zu ermitteln. Es wird an Beispielen gezeigt, wie man hier sinnvoller vorgehen kann. 1. Zunächst ist es wichtig, nicht nur die Einfügedämmung sondern auch die Originalspektren mit und ohne Minderung zu dokumentieren und zu veröffentlichen, damit man kontrollieren kann, ob wesentliche Amplituden und Frequenzbereiche reduziert sind oder ob es sich um eher zufällige Minderungen oder Verstärkungen handelt. (Beispiel Unterschottermatte/Raron, Müller/SBB) 2. Der Messpunkt sollte nicht im Nahbereich des Gleises liegen, da ansonsten eine zu günstige, falsche Einfügedämmung bestimmt wird. (Beispiel Tunnel/ Leipzig/Breitsamter) 3. Um Zufälligkeiten zu vermeiden, sollte man an mehr als einem Punkt messen. (Beispiel Unterschotterplatte/Altheim/Auersch) 4. Man sollte eigentlich immer auch die Bodenkennwerte (Steifigkeit, Dämpfung, Amplituden-abnahme, Übertagungsfunktion) messen. Selbst bei nahegelegene Messquerschnitten kann man Überraschungen erleben. (Beispiel erste ICE-Messungen/bei Würzburg/Auersch) 5. Bei verschiedenen Bodenkennwerten kann man eine Korrektur durchführen. (Beispiel Gleis-tröge/Mistler) Am besten bestimmt man ein äquivalentes Kraftspektrum zu jedem Messort und jedem Messzug (Beispiel Feste Fahrbahn/Gardelegen/Auersch) 6. Prinzipiell gibt es nicht die Einfügedämmung einer Maßnahme. Die Einfügedämmung ist immer boden- und referenzsystemabhängig. Die „beste“ Einfügungsdämmung erhält man mit einem steifen Untergrund (Beispiel Unterschottermatte/Tunnel/München Gasteig/Wettschureck) Das heißt aber nicht, dass die Maßnahme durch einen künstlich versteiften Untergrund besser wird (Beispiel Unterschottermatten/RRT2006/Auersch) Es werden Messbeispiele gezeigt, die alle neben einer hochfrequenten dynamischen Minderung auch eine mittelfrequente quasi-statische Minderung aufweisen. Dabei wird der mittelfrequente Zerstreuanteil der statischen Achslastimpulse durch die breitere Lastverteilung und damit die Impulsdehnung der Achslastimpulse reduziert. Diese Impulsdehnung lässt sich mit dem 2-dimensionalen Gleismodell berechnen. Die Minderungswirkung hängt aber wiederum vom Referenzsystem und dessen unregelmäßiger Steifigkeitsverteilung ab. Je unregelmäßiger der Boden und Gleisuntergrund des Referenzsystems, desto stärker ist die Minderungswirkung.
The Bundesanstalt für Materialforschung und -prüfung (BAM) collaborates with TNO to develop a software framework for automated calibration of structural models based on monitoring data. The ultimate goal is to include such models in the asset management process of engineering structures. As a basis for developing the framework, a multi-span road bridge consisting of ten simply supported steel box girders was selected as a test case. Our group measured output-only vibration data from one box girder under ambient conditions. From the data, we determined eigenfrequencies and mode shapes. In parallel, we developed a preliminary structural model of the box girder for the purpose of predicting its modal properties. In this contribution, we provide an overview of the measurement campaign, the operational modal analysis, the structural modeling and qualitatively compare the identified with the predicted modes. As an outlook, we discuss the further steps in the calibration process and future applications of the calibrated model.
Quenching and partitioning (Q&P) steels are characterized by an excellent combination of strength and ductility, opening up great potentials for advanced lightweight components. The Q&P treatment results in microstructures with a martensitic matrix being responsible for increased strength whereas interstitially enriched metastable retained austenite (RA) contributes to excellent ductility. Herein, a comprehensive experimental characterization of microstructure evolution and austenite stability is carried out on a 42CrSi steel being subjected to different Q&P treatments. The microstructure of both conditions is characterized by scanning electron microscopy as well as X‐ray diffraction (XRD) phase analysis. Besides macroscopic standard tensile tests, RA evolution under tensile loading is investigated by in situ XRD using synchrotron and laboratory methods. As a result of different quenching temperatures, the two conditions considered are characterized by different RA contents and morphologies, resulting in different strain hardening behaviors as well as strength and ductility values under tensile loading. In situ synchrotron measurements show differences in the transformation kinetics being rationalized by the different morphologies of the RA. Eventually, the evolution of the phase specific stresses can be explained by the well‐known Masing model.
A significant number of new wind farms has to be installed and, at the same time, existing wind farms reaching the end of their planned life need to be reused efficiently to ensure that the ambitous goals for deploying offshore wind are met. Some relevant reuse alternatives for offshore wind farms are lifetime extension, repowering utilizing existing substructures and full replacement. In this presentation - starting from experience gained from extending the lifetime of the of the U1 metro viaduct in Berlin - we discuss end-of-life decision making in offshore wind. We focus particularly on issues concerning substructures and highlight existing challenges and opprtunities in research and development.
Wir zeigen, dass bei homogenen ausgeprägt sandartigen Böden mit statistisch ermittelten Korrelationen die dynamischen Bodensteifigkeiten mit einer Genauigkeit abgeschätzt werden können, die mit der Ungenauigkeit der seismischen Verfahren übereinstimmt. Mit zunehmenden Feinkornanteil werden die Unsicherheiten der statistischen Korrelationen größer. Bei stark überkonsolidierten glazialen Böden sollte von der Anwendung empirischer Korrelationen Abstand genommen werden.
Current standards like ISO 14837-32:2015 and DIN EN 1998-1/NA:2021 as well as prEN 1997-2:2022 allow for using correlations between the results of in-situ soil penetration tests and shear wave velocity (or shear modulus) to determine soil properties to be used in dynamic analyses. While the ISO and prEN standards even provide some recommendations on specific correlations to be used, the DIN standard does not. Due to the statistical nature of such correlations their general applicability has to be verified. We collected data sets from test sites from Germany as well as New Zealand at which cone penetration tests (CPT) as well as seismic site investigation methods were conducted. These sites comprise sandy soils as well as clayey soils, mixed soils as well as glacial soils. We compare the results of several correlations between CPT results and shear wave velocity. The accuracy of such correlations is assessed with respect to the accuracy of seismic in-situ tests. It turns out that for clean sands such correlations between CPT and Vs have a similar order of variability as seismic in-situ tests conducted at the same site. The higher the fines portion of the soil, the higher the variability of the statistical correlations, and consequently the less the general applicability. For glacial soils and other special soil types usage of statistical correlations to determine dynamic soil properties is not recommended.
Nowadays geotechnical engineering firms have powerful software tools to extent their consulting business also into dynamic soil-structure interaction, which before has been restricted to a rather small community of specialized experts in this field, and they certainly do. This is particularly true with respect to non-seismic sources, that is all kinds of human induced vibrations. Hence, there is a demand from clients as well as from contractors to have guidance on the requirements as well as the limits of numerical modelling of soil-structure interaction. From the literature as well as from relevant standards, recommendations for the numerical modelling of soil-structure interaction problems involving seismic actions are well known, e. g. ASCE/SEI 4-16. There are, however, some particularities when dealing with human-induced vibrations, which are absent in seismic analyses. For human-induced excitations very little specific guidance has been published in the past. A machine foundation on a homogeneous half space excited by harmonic loads with excitation frequency between 4 Hz and 64 Hz has been analysed by means of several commercially available software packages. Parametric studies have been performed to verify if recommendations for seismic soil-structure analyses are valid for non-seismic analyses as well. This paper provides details on the benchmark example and the most important conclusions from the undertaken parametric studies.
Messtechnische Systeme zur Dauerüberwachung von Bauwerken ermöglichen Einblicke in deren reale Trag- und Verformungsverhalten. Die Planung und technische Umsetzung solcher Maßnahmen erfordern für die erfolgreiche Erfüllung der Aufgabenstellungen eine hohe Fachkompetenz, sowohl auf der planerischen Seite, als auch für die fachliche Bewertung von angebotenen Monitoringlösungen. Als Hilfestellung dafür wurde von der Deutschen Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) das Merkblatt „Dauerüberwachung von Ingenieurbauwerken“ erarbeitet, welches nun verfügbar ist. In diesem Beitrag werden die Inhalte des neuen Merkblatts vorgestellt und dieses in die vorhandene Literatur eingeordnet.
Lehmmauerwerk bietet sich aufgrund seiner zahlreichen ökologischen Vorteile für die Errichtung klimafreundlicher und ressourcenschonender Gebäude an. Um den Anwendungsbereich tragenden Lehmmauerwerks durch eine zeitgemäße Nachweisführung zu erweitern, werden in diesem Beitrag Grundlagen für die Entwicklung eines eurocodekonformen Bemessungskonzepts erarbeitet. Hierzu werden die Ergebnisse umfangreicher experimenteller Untersuchungen an Lehmmauerwerk sowie Lehmsteinen und -mörteln nach Konditionierung bei unterschiedlichen Klimata vorgestellt. Darauf aufbauend erfolgt eine Traglastanalyse druckbeanspruchter Lehmmauerwerkswände mittels numerischer und analytischer Methoden. Die daraus gewonnenen Erkenntnisse werden abschließend in einen an DIN~EN~1996-3/NA angelehnten Bemessungsvorschlag überführt, welcher die materialspezifischen Besonderheiten von Lehmmauerwerk berücksichtigt und eine fundierte Grundlage für eine wirtschaftliche und zuverlässige Nachweisführung darstellt.
The Bundesanstalt für Materialforschung und -prüfung (BAM) collaborates with TNO to develop a software framework for automated calibration of structural models based on monitoring data. The ultimate goal is to include such models in the asset management process of engineering structures. As a basis for developing the framework, a multi-span road bridge consisting of ten simply supported steel box girders was selected as a test case. Our group measured output-only vibration data from one box girder under ambient conditions. From the data, we determined eigenfrequencies and mode shapes. In parallel, we developed a preliminary structural model of the box girder for the purpose of predicting its modal properties. In this contribution, we provide an overview of the measurement campaign, the operational modal analysis, the structural modeling and qualitatively compare the identified with the predicted modes. As an outlook, we discuss the further steps in the calibration process and future applications of the calibrated model.
The vehicle–track interaction generates forces and consequently vibrations in the environment. The interaction has been analysed by the simultaneous measurements of vehicle, track and ground vibrations during test runs with varied train speeds. The special effects of the passage over a bridge and through a tunnel are studied and compared with the measurements on a conventional ballasted surface line. The maximum amplitudes, narrow band and one-third octave band spectra are presented for the axle-box accelerations and for the track, bridge and ground vibrations. The different frequencies and frequency bands are related to wheel out-of-roundness, track alignment errors, the sleeper passage and the wheelset–track resonance. An axle impulse component has been observed at the track, at the near-field soil and as a scattered version in the far field. Specific results can be found for the bridge track, where clearly speed-dependent bridge resonances occur due to the axle sequence of the train, and for the tunnel track where soft rail pads are responsible for a strong amplification around the wheelset–track resonance. On the other hand, the axle impulses are strongly reduced by the tunnel track, and the scattered axle impulse component is not as relevant as for the surface track. As a consequence, a strong mid-frequency amplitude reduction of the tunnel compared to the surface line has been measured for low and high train speeds by the Federal Institute of Material Research and Testing (BAM) and by other institutes.
The propagation of ground vibrations is theoretically analysed with frequency-wavenumber and simplified methods. Experimental methods are presented which can characterise the site-specific ground vibrations by wave velocities, stiffness and damping. Measurements with hammer and train excitation have been performed at several sites. The one-third octave spectra show the stiffness-dependent amplitudes and the low- and high-frequency filter effects due to the layering and the damping of the soil. Specific train effects, an additional high-frequency filter, the sleeper passage frequency, and an amplified mid-frequency component can be clearly found. The attenuation with distance is analysed in detail where the theoretical exponential and the empirical frequency-dependent power law are considered. Hammer and train excitation show the same site-specific effects which are mainly due to the stronger or weaker damping of the soil. The train attenuation is generally weaker than the hammer attenuation. The attenuation exponent of the power law, which is strongly dependent on the site and the frequency, is reduced for the train vibration by 0.3 to 0.5 in agreement with the theory. Reasons are discussed for the overall power law and for the dominating mid-frequency component.
The Federal Institute of Material Research and Testing has performed many impact tests from very small laboratory tests to very big “free-field” tests with heavy containers on stiff foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. Later on, a smaller drop test facility has been built on the ground inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which oc-cur during the drop tests. In addititon, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Dif-ferent sensors, accelerometers, accelerometers with mechanical filters, geo-phones (velocity transducers), strain gauges, and pressure cells have been ap-plied for these tasks. Signal transformations and model calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple esti-mation.
The Federal Institute of Material Research and Testing has performed many impact tests from very small laboratory tests to very big “free-field” tests with heavy containers on stiff foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. Later on, a smaller drop test facility has been built on the ground inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which oc-cur during the drop tests. In addititon, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Dif-ferent sensors, accelerometers, accelerometers with mechanical filters, geo-phones (velocity transducers), strain gauges, and pressure cells have been ap-plied for these tasks. Signal transformations and model calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple esti-mation.