7.2 Ingenieurbau
Filtern
Erscheinungsjahr
- 2019 (65) (entfernen)
Dokumenttyp
- Vortrag (33)
- Beitrag zu einem Tagungsband (23)
- Zeitschriftenartikel (7)
- Buchkapitel (1)
- Posterpräsentation (1)
Schlagworte
- Fatigue (6)
- Grout (5)
- Impact (5)
- Temperature rejection (5)
- Train-induced ground vibration (5)
- Damage characterization (4)
- Damage localization (4)
- Ground vibration (4)
- Layered soils (4)
- Numeric simulation (4)
- Planar tomography (4)
- Reinforced concrete structure (4)
- Soil-structure interaction (4)
- Vehicle-track-soil interaction (4)
- Load vector (3)
- Model interpolation (3)
- Offshore foundations (3)
- Statistical evaluation (3)
- Statistical method (3)
- Subspace-based method (3)
- Vibration measurements (3)
- Wellengeschwindigkeit (3)
- Bahnerschütterungen (2)
- Bodenübertragungsfunktion (2)
- Bridges (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Compaction Grouting (2)
- Compressive Cyclic loading (2)
- Crack detection (2)
- Crack formation (2)
- Crack pattern (2)
- Cyclic load (2)
- Dispersionsmessung (2)
- Displacements (2)
- Drone (2)
- Excitation forces (2)
- Fly ash (2)
- Grouted connection (2)
- Hammer impact (2)
- High-strength concrete (2)
- Injection Sequence (2)
- Inspection planning (2)
- Interface (2)
- Long-term shrinkage (2)
- Metakaolin (2)
- Micro silica (2)
- Mitigation (2)
- Modal Analysis (2)
- Non destructive testing (2)
- Offshore Pile Foundation (2)
- Offshore wind turbines (2)
- Reliability (2)
- Risk (2)
- SDDLV (2)
- SHM (2)
- Slab track (2)
- Static load (2)
- Steel structures (2)
- Structural Health Monitoring (2)
- Structural health monitoring (2)
- Tensile Capacity (2)
- Train excitation (2)
- Train passage (2)
- Train speed (2)
- Ultrasonic testing (2)
- Uncertainty (2)
- Vibration (2)
- Wind Turbines (2)
- Zuggeschwindigkeit (2)
- Analytical Design Methods (1)
- Automated Modal Analysis for Tracking Structural Change during Construction and Operation Phases (1)
- BIM (1)
- Brücken (1)
- Climate Chamber (1)
- Components of excitation (1)
- Compressive strength (1)
- Concrete (1)
- Continuously inhomogeneous soils (1)
- DUCON® (1)
- Deckeneigenfrequenzen (1)
- Design methods (1)
- Ductility (1)
- E-modulus (1)
- EERA Joint Program (1)
- Earthen hydraulic infrastructures (1)
- Environmental Effects (1)
- Erneuerbare Energien (1)
- Erosion (1)
- Finite-element boundary-element method (1)
- Foundation Pile (1)
- GPU parallel computation (1)
- Gebäudemodelle (1)
- Gebäudeschwingungen (1)
- Ground vibration measurements (1)
- Horizontal stress (1)
- Inhomogeneous soils (1)
- Klimakammer (1)
- Measurement campaigns (1)
- Mechanical challenges (1)
- Messen im Bauwesen (1)
- Micro-reinforcement (1)
- Microfine Cement (1)
- Micromechanical analysis (1)
- Micromechanical modelling (1)
- Mobile elements (1)
- Multi-beam method (1)
- Numerical modeling (1)
- Numerical modelling (1)
- Offshore (1)
- Offshore geotechnics (1)
- Offshore steel structures (1)
- Offshore wind energy (1)
- Offshore wind energy foundations (1)
- Physical phenomenology (1)
- Physical testing (1)
- Pile bending stiffness (1)
- Pile foundation (1)
- Pile foundations (1)
- Prediction (1)
- Quasi-static and dynamic tests (1)
- SHM Environmental (1)
- SHM environmental bridges (1)
- Scattered axle impulses (1)
- Shrinkage Reducing Admixture (1)
- Soft track elements (1)
- Soil stiffness (1)
- Soil-water-structure interaction (1)
- Spektralanalyse (1)
- Stability Buckling soil-structure-interaction piles offshore (1)
- Stereo photogrammetry (1)
- Superplasticizer (1)
- Supplementary Cementitious Materials (1)
- Tagung (1)
- Temperature effect rejection (1)
- Temperature effects (1)
- Temperature modeling (1)
- Temperatureinflüsse (1)
- Track beam (1)
- UHPC (1)
- Un- certainty (1)
- Vehicle-track interaction (1)
- Wavenumber integrals (1)
- Wavenumber method (1)
- Wellenausbreitung (1)
- Wheelset accelerations (1)
- Wind energy (1)
- Wind energy tower (1)
- Windenergie (1)
- elastische Gebäudelagerungen (1)
- risk, reliability, inspection planning, offshore wind turbines (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (65) (entfernen)
Eingeladener Vortrag
- nein (33)
The shaft bearing capacity often plays a dominant role for the overall structural behaviour of axially loaded piles in offshore deep foundations. Under cyclic loading, a narrow zone of soil at the pile-soil interface is subject to cyclic shearing solicitations. Thereby, the soil may densify and lead to a decrease of confining stress around the pile due to microphenomena such as particle crushing, migration and rearrangement. This reduction of radial stress has a direct impact on the shaft capacity, potentially leading in extreme cases to pile failure. An adequate interface model is needed in order to model this behaviour numerically. Different authors have proposed models that take typical Interface phenomena in account such as densification, grain breakage, normal pressure effect and roughness. However, as the models become more complex, a great number of material parameters need to be defined and calibrated. This paper proposes the adoption and transformation of an existing soil bulk model (Pastor- Zienkiewicz) into an interface model. To calibrate the new interface model, the results of an experimental campaign with the ring shear device under cyclic loading conditions are here presented. The constitutive model shows a good capability to reproduce typical features of sand behaviour such as cyclic compaction and dilatancy, which in saturated partially-drained conditions may lead to liquefaction and cyclic mobility phenomena.
The shaft bearing capacity often plays a dominant role for the overall structural behaviour of axially loaded piles in offshore deep foundations. Under cyclic loading, a narrow zone of soil at the pile-soil interface is subject to cyclic shearing solicitations. Thereby, the soil may densify and lead to a decrease of confining stress around the pile due to microphenomena such as particle crushing, migration and rearrangement. This reduction of radial stress has a direct impact on the shaft capacity, potentially leading in extreme cases to pile failure. An adequate interface model is needed in order to model this behaviour numerically. Different authors have proposed models that take typical Interface phenomena in account such as densification, grain breakage, normal pressure effect and roughness. However, as the models become more complex, a great number of material parameters need to be defined and calibrated. This paper proposes the adoption and transformation of an existing soil bulk model (Pastor- Zienkiewicz) into an interface model. To calibrate the new interface model, the results of an experimental campaign with the ring shear device under cyclic loading conditions are here presented. The constitutive model shows a good capability to reproduce typical features of sand behaviour such as cyclic compaction and dilatancy, which in saturated partially-drained conditions may lead to liquefaction and cyclic mobility phenomena.
The structural performance of many geotechnical systems (e.g. axially-loaded pile foundations), depends on the shearing resistance at the soil interface, which may govern the load bearing capacity of the foundation. Experimental investigations have shown that this interaction is mainly localised within a narrow shear band next to the structure. Under cyclic loading, a contraction of the soil at the interface may arise (net volume loss), possibly leading to a stress relaxation and thus to a reduction of the load bearing capacity (the so-called friction fatigue). Based on the constitutive similarities between soil continua and interfaces, we propose here the adaption of a Generalized Plasticity model for sandy soils for the numerical analysis of interface problems. In this contribution, the results of an experimental campaign for the parameter calibration of the constitutive model are presented. The tests have been conducted with a ring shear device involving different normal stresses, roughness of the steel plates as well as cyclic loading. The new modelling approach shows promising results and has the additional practical advantage that the interface zone and the soil continuum can both be described with the same constitutive model in general boundary value problems.
Methods have been presented for detailed studies of railway vibration and for the fast prediction of train-induced ground vibration. The ground vibration is generated by static or dynamic loads. The main purpose of this contribution was to show the influence of inhomogeneous soils on the different vibration components.
Layered soils, namely a soft layer on a stiffer half-space, yield a quite specific transmission behavior. The low-frequency and sometimes also high-frequency cut-off of the transfer function of the soil is demonstrated in theory and by experiments at many sites of which the soil model is approximated from dispersion and transfer function measurements. The layer frequency divides the frequency range in a low-frequency range, where the stiff half-space rules the low amplitudes, and a high amplitude high-frequency range which is mainly determined by the softer top layer. A thick soft layer yields a very low layer frequency, so that the higher soft soil amplitudes have a wider range down to low frequencies. A thin layer yields a high layer frequency, so that the high frequencies above this layer frequency are dominant. The higher the contrast between the stiff half-space and the soft layer is, the stronger the increase between the half-space and layer amplitudes, the more characteristic are the spectra of the soil transfer function. The range of measured soils has been from vS1 down to 125 m/s, vS2 up to 1000 m/s and the layer frequencies are within 10 Hz < f0 < 75 Hz. Moreover, during this measuring campaign in Switzerland, all 11 sites showed clearly the layer-on-half-space behaviour. The transfer functions of inhomogeneous soils have been used to predict the ground vibration due to dynamic axle loads which is usually thought to be the most important component.
The passage of static loads, in the contrary, results in very small vibration amplitudes for low train speeds, which can only be found at near distances and at low frequencies. They attenuate very rapidly with distance and lose very rapidly the higher frequency content. The passage of static axle loads can be included in the prediction of railway vibration just for completeness.
Special attention should be given to the case if the train runs with the Rayleigh-wave speed of the soil (Rayleigh train). The Rayleigh-train effect is strongest for a homogeneous half-space: At the near-field of the track the amplitudes are raised strongly compared to normal trains, and in addition, little attenuation with distance is observed. In case of a layered soil, the low-frequency cut-off reduces the frequency range and the amplitudes of the homogeneous quasi-static ground vibrations. Therefore, the Rayleigh-train effects are clearly reduced by a layered soil and they disappear if the layer frequency (for example for a thin layer) is higher than the frequency band of the axle impulse. The Rayleigh-train effect could completely disappear in a randomly inhomogeneous soil, but this has not been analysed so far.
The axle impulses from static loads can have an additional, quite different effect. They can be scattered by a randomly inhomogeneous soil so that a part (the scattered part) of the axle impulse can reach further distances from the track. This can establish a certain mid-frequency component of the ground vibration which becomes dominant in the far-field, and this important component exists for all train speeds. Experimental results from BAM and international measurements show the importance of the corresponding frequency range.
The mitigation of train induced ground vibration by elastic and stiff track elements has been analysed threefold. The vehicle-track interaction yields the reduction at high frequencies above the vehicle-track resonance. This is the standard effect. The filtering of trackbed errors by the bending stiffness of the track yields a certain mid-frequency effect. An even stronger mid-frequency effect is predicted for the mitigation of the scattered axle impulses by the bending stiffness and elastic elements of the track.
Abstract. Three measurement campaigns of train-induced ground vibrations are evaluated for the vehicle-track-soil interaction. Ground vibrations, track vibrations and vehicle vibrations have been measured for train passages and impulse excitation and compared with theoretical results.
The soil and the track-soil system are calculated by wavenumber integrals. The influence of the vehicle is introduced by a substructure method. By comparing theory and measurement the different components of excitation force and ground vibration can be analysed, the quasi-static excitation, track-alignment errors, the out-of-roundness of wheels, the wheel and rail roughness, and moreover, scattered axle impulses and ineffective high-frequency parts of the wheelset accelerations and forces.
Temperature variation can be a nuisance that perturbs vibration based structural health monitoring (SHM) approaches for civil engineering structures. In this paper, temperature affected vibration data is evaluated within a stochastic damage detection framework, which relies on a null space based residual. Besides two existing temperature rejection approaches – building a reference state from an averaging method or a piecewise method – a new approach is proposed, using model interpolation. In this approach, a General reference model is obtained from data in the reference state at several known reference temperatures.
Then, for a particular tested temperature, a local reference model is derived from the general reference model. Thus, a well fitting reference null space for the formulation of a residual is available when new data is tested for damage detection at an arbitrary temperature. Particular attention is paid to the computation of the residual covariance, taking into account the uncertainty related to the null space Matrix estimate. This improves the test performance, contrary to prior methods, for local and global damages, resulting in a higher probability of detection (PoD) for the new interpolation approach compared to previous approaches.
The subject of damage localization is an important issue for Structural Health Monitoring (SHM) particularly in mechanical or civil structures under ambient excitation. In this paper, the statistical subspacebased damage localization method has been applied on a benchmark application, namely a 1/200 scale model of the Saint-Nazaire Bridge, which is a cable-stayed bridge located on the Loire River near the river’s mouth. The employed damage localization method combines data-driven features with physical parameter information from a finite element model in statistical tests, avoiding typical ill-conditioning problems of FE model updating. Damage is introduced in the mockup for cable failures on some of the 72 cables. The purpose of the experiment is to assess the capability of damage assessment methods to find a cable failure.
The Stochastic Dynamic Damage Locating Vector (SDDLV) approach is a vibration-based damage localization method based on both a finite element model of a structure and modal parameters estimated from output-only measurements in the damage and reference states. A statistical version of the Approach takes into account the inherent uncertainty due to noisy measurement data. In this paper, the effect of temperature fluctuations on the performance of the method is analyzed in a model-based approach using a finite element model with temperature dependent parameters. Robust damage localization is carried out by rejecting the temperature influence on the identified modal parameters in the damaged state. The algorithm is illustrated on a simulated structure.
Temperature variation can be a nuisance that perturbs vibration based structural health monitoring (SHM) approaches for civil engineering structures. In this paper, temperature affected vibration data is evaluated within a stochastic damage detection framework, which relies on a null space based residual. Besides two existing temperature rejection approaches – building a reference state from an averaging method or a piecewise method – a new approach is proposed, using model interpolation. In this approach, a general reference model is obtained from data in the reference state at several known reference temperatures. Then, for a particular tested temperature, a local reference model is derived from the general reference model. Thus, a well fitting reference null space for the formulation of a residual is available when new data is tested for damage detection at an arbitrary temperature. Particular attention is paid to the computation of the residual covariance, taking into account the uncertainty related to the null space matrix estimate. This improves the test performance, contrary to prior methods, for local and global damages, resulting in a higher probability of detection (PoD) for the new interpolation approach compared to previous approaches.
The subject of damage localization is an important issue for Structural Health Monitoring (SHM) particularly in mechanical or civil structures under ambient excitation. In this paper, the statistical subspacebased damage localization method has been applied on a benchmark application, namely a 1/200 scale model of the Saint-Nazaire Bridge, which is a cable-stayed bridge located on the Loire River near the river’s mouth. The employed damage localization method combines data-driven features with physical parameter information from a finite element model in statistical tests, avoiding typical ill-conditioning problems of FE model updating. Damage is introduced in the mockup for cable failures on some of the 72 cables. The purpose of the experiment is to assess the capability of damage assessment methods to find a cable failure.