7.2 Ingenieurbau
Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (82) (entfernen)
Sprache
- Englisch (66)
- Deutsch (15)
- Mehrsprachig (1)
Schlagworte
- Ground vibration (6)
- Structural health monitoring (6)
- Fatigue (5)
- Structural Health Monitoring (5)
- Model interpolation (4)
- Vibration measurements (4)
- Building vibration (3)
- Damage localization (3)
- Hammer impact (3)
- Impact (3)
- Layered soil (3)
- Reliability (3)
- Temperature rejection (3)
- Bahnerschütterungen (2)
- Bayesian updating (2)
- Cable failure (2)
- Cable-stayed bridge (2)
- Container loading (2)
- Damage characterization (2)
- Drop test (2)
- Environmental effects (2)
- Erschütterungen (2)
- Fault detection (2)
- Foundation load (2)
- Grout (2)
- High-strength concrete (2)
- Inspection planning (2)
- Interface (2)
- Linear parameter varying systems (2)
- Load vector (2)
- Modalanalyse (2)
- Monitoring (2)
- Offshore (2)
- Planar tomography (2)
- Repair (2)
- Risk (2)
- SDDLV (2)
- Soil-structure interaction (2)
- Soil-wall-floor model (2)
- Statistical evaluation (2)
- Structural systems (2)
- Subspace-based method (2)
- Subspace-based residual (2)
- Train passage (2)
- Train-induced ground vibration (2)
- Ultrasonic testing (2)
- Vehicle-track interaction (2)
- Vibration (2)
- Wind (2)
- 2-span bridge (1)
- Achsfolgespektren (1)
- Acoustic emission testing (1)
- Amplitude-charge weight laws (1)
- Amplitude-distance laws (1)
- Analysis of variance (1)
- Analytical Design Methods (1)
- Ansys Autodyn (1)
- Apartment building (1)
- Artificial Intelligence (1)
- Artificial intelligence (1)
- Attenuation (1)
- Autonomous underwater vehicles (1)
- Axle impulses (1)
- Axle loads (1)
- Axle-sequence spectrum (1)
- BIM (1)
- Bauteile (1)
- Bauwerke (1)
- Bayesian System Identification (1)
- Bayesian methods (1)
- Bayesian system identification (1)
- Belastungsversuch (1)
- Big Data (1)
- Bodenvariabilität (1)
- Bodenübertragungsfunktion (1)
- Box-Behnken (1)
- Bridges (1)
- Brücke (1)
- Brücken (1)
- Changing process noise (1)
- Chemisoprtion (1)
- Climate chamber (1)
- Column/wall resonance (1)
- Compaction Grouting (1)
- Compaction grouting (1)
- Compressive Cyclic loading (1)
- Compressive cyclic loading (1)
- Compressive strength (1)
- Computer Vision (1)
- Conductor (1)
- Coupler systems (1)
- Crack Luminescence (1)
- Crack detection (1)
- Crack formation (1)
- Crack growth (1)
- Crack pattern (1)
- Cracks (1)
- Cyber security (1)
- Cyclic load (1)
- DEM (1)
- DUCON® (1)
- Damage detection (1)
- Damage identification (1)
- Datenmanagement (1)
- Deterioration (1)
- Digital Image Correlation (DIC) (1)
- Digital Models (1)
- Digital twin (1)
- Dispersionsmessung (1)
- Displacements (1)
- Drone (1)
- Drop Tests (1)
- Drop tower (1)
- Drucker-Prager (1)
- Ductility (1)
- Dynamische Bodensteifigkeit (1)
- E-modulus (1)
- Earth (1)
- Earth masonry (1)
- Elastische Gebäudelagerung (1)
- Elastische Gleiselemente (1)
- Emission (1)
- Energy (1)
- Environmental changes (1)
- Erschütterungsausbreitung (1)
- Erschütterungsminderung (1)
- Erschütterungsprognose (1)
- Evaluation (1)
- Excitation forces (1)
- Explosion-induced ground vibrations (1)
- Fallturm (1)
- Faseroptik (1)
- Fault detectionchanging (1)
- Feuchte (1)
- Filter effects (1)
- Finite Elemente Simulation (1)
- Finite element models (1)
- Floor resonance (1)
- Foundation Pile (1)
- Foundation reliability analysis (1)
- Freight train (1)
- Freileitung (1)
- Gleiströge (1)
- Granular Cohesive Materials (1)
- Ground vibration measurements (1)
- Grouted Connection (1)
- Grouted connection (1)
- Grouting (1)
- Großer Fallturm Horstwalde (1)
- HAZID (1)
- HTLS (1)
- Halbraum (1)
- Hard impact (1)
- Harter Anprall an Stahlbetonstrukturen (1)
- High-Rise Building (1)
- High-speed (1)
- High-speed train (1)
- Horizontal stress (1)
- Immission (1)
- Impact damage on reinforced concrete (1)
- Impakt (1)
- Inertial Interaction (1)
- Injection Sequence (1)
- Inspection (1)
- Irregular ballast (1)
- Irregular soil (1)
- Irregularities (1)
- Kinematic Interaction (1)
- Knudsen effect (1)
- Laboratory beam structure (1)
- Layered soils (1)
- Lehm (1)
- Load-bearing (1)
- Long-span bridge (1)
- Macromechanical Sample Strength (1)
- Maschinenbetrieb (1)
- Material Point Method (MPM) (1)
- Material moisture (1)
- Material tests (1)
- Mauerwerk (1)
- Measurement (1)
- Measurements (1)
- Micro-reinforcement (1)
- Microfine Cement (1)
- Micromechanical Tensile Failure (1)
- Minderungsmaßnahmen (1)
- Mixed formulation (1)
- Mobile elements (1)
- Modal Analysis (1)
- Modal force spectrum (1)
- Modes (1)
- Moisture (1)
- Molecular diffusion (1)
- Monopile installation risks (1)
- Multiple impact (1)
- NDT (1)
- Nachgiebigkeiten (1)
- Non destructive testing (1)
- Non-Destructive Evaluation (1)
- Non-destructive testing (1)
- Numeric simulation (1)
- Numerical damage simulation (1)
- Numerical modeling (1)
- Numerical modelling (1)
- Office building (1)
- Office tower (1)
- Offshore Pile Foundation (1)
- Offshore Wind Energy (1)
- Offshore foundations (1)
- Offshore pile foundation (1)
- Offshore steel structures (1)
- Offshore wind energy (1)
- Offshore wind turbines (1)
- Optimal Sensor Placement (1)
- Passenger train (1)
- Physisorption (1)
- Pile Foundation (1)
- Post-impact evaluation (1)
- Prediction of explosion induced ground and building vibration (1)
- Probabilistic modelling (1)
- Probability of Detection (1)
- Process noise (1)
- Propagation from a tunnel (1)
- Prädiktive Instandhaltung (1)
- Quasi-static and dynamic tests (1)
- Radar (1)
- Railway (1)
- Railway bridge (1)
- Railway tunnel (1)
- Randomly heterogeneous soil (1)
- Rechenmodelle (1)
- Rehabilitation (1)
- Reinforced concrete structure (1)
- Reinforcement (1)
- Research data management (1)
- Residential building (1)
- Residual evaluation (1)
- Risk-based design (1)
- SHM (1)
- SHM environmental bridges (1)
- Safety (1)
- Scattering (1)
- Scherwellengeschwindigkeit (1)
- Schubmodul (1)
- Schwingungsdynamik (1)
- Shearing (1)
- Shell Buckling (1)
- Shrinkage Reducing Admixture (1)
- Simple prediction (1)
- Size effect (1)
- Slab track (1)
- Slenderness effect (1)
- Soft impact (1)
- Soil properties (1)
- Soil-Structure-Interaction (1)
- Soil-building interaction (1)
- Soil-building resonance (1)
- Soil-pile interaction (1)
- Spatially varying ground conditions (1)
- Static load (1)
- Statistical method (1)
- Statistical tests (1)
- Statistische Auswertung (1)
- Steel structures (1)
- Stereo photogrammetry (1)
- Strength (1)
- Subspace methods (1)
- Superplasticizer (1)
- Supplementary Cementitious Materials (1)
- Supplementary cementitious materials (1)
- Surface Foundation (1)
- Surface-tunnel reduction (1)
- System Identification (1)
- Temperature effects (1)
- Tensile Capacity (1)
- Time-variant reliability (1)
- Tomographic damage evaluation (1)
- Tragfähigkeit (1)
- Train speed (1)
- Transfer function (1)
- Transmission (1)
- Tunnel (1)
- Tunnel-pile transfer (1)
- UHPC (1)
- Umwelteinflüsse (1)
- Uncertainty (1)
- Uncertainty in reference (1)
- Value of Information (1)
- Varying stiffness (1)
- Vehicle-track-soil interaction (1)
- Vibration measurement (1)
- Vollraum (1)
- Waves (1)
- Welded (1)
- Wellenausbreitung (1)
- Wellenausbreitung in der Tiefe (1)
- Wellengeschwindigkeit (1)
- Wind Energy (1)
- Wind Turbines (1)
- Windenergie (1)
- Windenergieanlagen (1)
- Zerstreute Achsimpulse (1)
- Zuggeschwindigkeit (1)
- building information modelling (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- temperature (1)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (82)
- 7.2 Ingenieurbau (82)
- 7.4 Baustofftechnologie (8)
- 8 Zerstörungsfreie Prüfung (7)
- 7.1 Baustoffe (4)
- 3 Gefahrgutumschließungen; Energiespeicher (2)
- 3.3 Sicherheit von Transportbehältern (2)
- 7.0 Abteilungsleitung und andere (2)
- 8.2 Zerstörungsfreie Prüfmethoden für das Bauwesen (2)
- 8.5 Röntgenbildgebung (2)
Die Bundesanstalt für Materialforschung und -prüfung hat in den letzten 30 Jahren an vielen Orten Bahnerschütterungen gemessen. Dabei wurden immer auch Versuche zur Bestimmung der Bodeneigen-schaften durchgeführt, meist mit Hammeranregung, gelegentlich auch mit Schwingeranregung. Es werden verschiedene Auswertemethoden wie Seismogramm-Montage, Spektrale Analyse (SASW), Multistation Analysis of Surface Waves (MASW), f,v-Analyse (Dispersion aus zweifacher Fourier-Analyse), Spatial AutoCorrelation (SPAC, hier auch für deterministische Quellen) vorgestellt. Durch Approximation der frequenzabhängigen Wellengeschwindigkeiten (Dispersion) oder der gemessenen Übertragungsfunktionen erhält man ein passendes Bodenmodell. Zu diesem Bodenmodell kann man dann die Übertragungsfunktionen für Hammer- und Zuganregung berechnen. Mit allgemeinen oder spezifischen Achslastspektren werden dann die Bahnerschütterungen prognostiziert und mit den Messergebnissen verglichen. Bei etlichen Messorten, insbesondere in der Schweiz, wurden deutliche Merkmale einer Bodenschichtung beobachtet. Es ergibt sich eine deutliche Reduktion der tiefen Frequenzanteile durch den steifen unterliegenden Halbraum. Die weiche Deckschicht bestimmt das hochfrequente Verhalten. Hier bewirkt die Materialdämpfung des Bodens oft einen starken Amplitudenabfall, sowohl mit der Entfernung als auch mit der Frequenz. Für den verbleibenden mittelfrequenten Anteil wurde an mehreren Messorten die Amplituden-Fahrgeschwindigkeits-Gesetzmäßigkeiten untersucht. Es gibt konstante bis stark ansteigende Amplituden, und es zeigt sich auch hier, dass der geschichtete Boden von entscheidender Bedeutung ist.
The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site.
The identification of the dynamic behavior of structures, like bridges and towers, is relevant to address multiple issues. In many cases the dynamic parameters should be acquired only once or at a frequency that doesn’t justify the installation of distinct vibration sensors for a long-term monitoring. To identify modal frequencies of a structure, a drone based mobile sensing platform has been implemented. This sensing platform measures the relative displacement be-tween the structure and the drone, which also shows a strong dynamic behavior under wind tur-bulences. By regarding the dynamic model of the drone and additional measurements at the dis-tance sensor the absolute movement of the structure can be estimated based on the measured relative distance. This time domain data is a suitable input for various operational modal analysis algorithms. The system has been used to identify the dynamic properties of test and real structure, like a 1.5 MW wind turbine tower.
Environmental based perturbations influence significantly the ability to identify structural dam-age in Structural Health Monitoring. Strategies are needed to classify such effects and consider them appropri-ately in SHM. It has to be considered if seasonal effects just mask the structural response or if temperature itself correlates to a weakening of the structure. Various methods have been developed and analyzed to separate environmental based effects from damage induced changes in the measures. Generally, two main approaches have emerged from research activity in this fields: (a) statistics-based tools analyzing patterns in the data or in computed parameters and (b) methods, utilizing the structural model of the bridge considering environmental as well as damage-based changes of stiffness values. With the background of increasing affordability of sensing and computing technology, effort should be made to increase sensitivity, reliability and robustness of proce-dures, separating environmental from damage caused changes in SHM measures. The contribution describes an attempt to evaluate both general strategies, their advantages and drawbacks. In addition, two vibration moni-toring procedures are introduced, allowing for temperature-based perturbations of the monitoring data.
At present, to produce renewable energy offshore wind farms play an important role. The available space combined with the more valuable wind conditions make offshore locations very attractive for wind powered energy production. In Europe a significant number of offshore wind farms already exist, especially in the North and Baltic Sea. In future this trend will continue, and further offshore wind farms will be built. The majority of offshore wind turbines are mounted on steel foundation structures. Due to the high-cyclic loading by wind and waves fatigue stress plays a substantial role regarding structural safety.
Besides the consideration of fatigue within the design process, to monitor existing steel structures for potential fatigue cracks during their life time is a major topic and a challenge.
For the structures of the offshore wind turbines are large and partially under water effective reliable methods for the detection of fatigue cracks are required.
This contribution presents investigations on different crack detection methods applied at high-cycle fatigue tests on small-scale welded steel samples as well as on large-scale welded steel components. The tests were conducted at the BAM laboratories. For crack detection mainly three different methods were used and compared. The first method regards to the measurement of strain by conventionally strain gauges. Secondly, the crack luminescence was used as a new and effective optical method for surface monitoring. And finally, crack detection by pressure differentials of the inner and outer section of tubular steel elements was investigated. A comparison study will emphasize the advantages and disadvantages of the different methods and show which of the described methods is potentially more suitable for an application on real offshore wind structures.
The structural performance of many geotechnical systems (e.g. axially-loaded pile foundations), depends on the shearing resistance at the soil interface, which may govern the load bearing capacity of the foundation. Experimental investigations have shown that this interaction is mainly localised within a narrow shear band next to the structure. Under cyclic loading, a contraction of the soil at the interface may arise (net volume loss), possibly leading to a stress relaxation and thus to a reduction of the load bearing capacity (the so-called friction fatigue). Based on the constitutive similarities between soil continua and interfaces, we propose here the adaption of a Generalized Plasticity model for sandy soils for the numerical analysis of interface problems. In this contribution, the results of an experimental campaign for the parameter calibration of the constitutive model are presented. The tests have been conducted with a ring shear device involving different normal stresses, roughness of the steel plates as well as cyclic loading. The new modelling approach shows promising results and has the additional practical advantage that the interface zone and the soil continuum can both be described with the same constitutive model in general boundary value problems.
Owners or operators of offshore wind farms perform inspections to collect information on the condition of the wind turbine support structures and perform repairs if required. These activities are costly and should be optimized. Risk-based methods can be applied to identify inspection and repair strategies that ensure an optimal balance between the expected total service life cost of inspection and repair, and the achieved risk reduction. Such an optimization requires explicit modeling of repairs. In this paper, the impact of different repair models on the results of a risk-based optimization of inspection and repair strategies is quantified in a numerical example considering a jacket-type steel frame subject to high-cycle fatigue. The example showed that, in this specific application, there is no need for detailed modeling of the behavior of repaired welded connections.
Global energy consumption will increase in the future necessitating both fossil fuels and renewable energy choices - especially wind energy. Such high energy demand requires installation of offshore energy structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with maintenances. Due to their large size and remote locations, cylindrical grouted joints are often adopted between substructure and foundation in these offshore platforms and wind structures such as monopiles. However, these connections are composite structures with exterior sleeve, interior pile and infill mortar. Degradation and settlements were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites were proven difficult to obtain ideal load bearing capacity. In-situ loading conditions were also found to be affecting the failure mechanism inside such connections. This study aims at characterizing the nature of cracks generated in these grouted connections under both static and cyclic loading. Scaled grouted joints were manufactured using a novel reusable mold, and connections were loaded to failure to visualize the main failure patterns. An assessment between failure under these two types of load is drawn along with comparison to previously available literature.
The aim of an ongoing research project is to develop a design approach for typical offshore driven piles (e.g. Jacket piles) based on the application of injections by compaction grouting directly at the pile shaft. The paper aims to present the results of laboratory and in-situ tests, which reveal the efficiency and the promising potential of the optimised foundation concept for a more economic dimensioning of pile foundations and to increase their bearing capacity in non-cohesive soil at any moment after installation.
Measured train passages and hammer impacts in combination with track-soil calculation have been successfully used for the detection of damaged slab tracks. This approach is now extended to intact slab and ballast tracks. The vibrations of many tracks have been measured at several levels from rail, sleeper, track plate, base plate, base layer to the subsoil by velocity or acceleration sensors. The time histories have to be integrated once or twice to get the displacements. The displacement signals include an arbitrary time-dependent shift which must be eliminated or respected in the interpretation. On the other hand, the calculation of slab and ballast tracks have been done in frequency-wavenumber domain. The displacements along the track and the frequency-dependent compliance transfer functions can be calculated. The latter can be compared with the results of the hammer impacts on the track. The deformation of the track can be transformed to time histories for a whole train and compared to the measured train passages. Many slab (and ballast) tracks have been measured at different sites. The displacements of the tracks are presented, and the following parameters have been analysed in the measurement results: slab track vs. ballast track, different types of slab tracks, damaged slab tracks, different trains, switches at different measuring points, an elastic layer, the mortar layer, different soils at different places. The soil should have the dominant influence on the track-plate displacements. Slab and ballast track yield also big differences in maximum displacement and width of deformation. Some of the preceding aspects will be analysed in comparison of measurement and theory.