5 Werkstofftechnik
Filtern
Erscheinungsjahr
- 2018 (70) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (70) (entfernen)
Sprache
- Englisch (70) (entfernen)
Schlagworte
- Residual stress (6)
- Additive manufacturing (4)
- 3D-Printing (3)
- EBSD (3)
- High temperature corrosion (3)
- Microstructure (3)
- Additive Manufacturing (2)
- Aging (2)
- Bacteria (2)
- Calcination (2)
- Creep (2)
- Damage (2)
- Degradation (2)
- Glass (2)
- IN718 (2)
- Laser ablation in liquid (2)
- Nanoparticles (2)
- Neutron diffraction (2)
- Particle morphology (2)
- Plastic deformation (2)
- Reaction-sintering (2)
- Selective laser melting (2)
- Steel (2)
- TEM (2)
- Titanium oxide (2)
- 3D printing (1)
- 3D-finite element modeling (1)
- Accelerated temporal integration (1)
- Advanced wastewater treatment (1)
- Ageing (1)
- Al-Cu-Li-alloy (1)
- Alloys (1)
- Alumina coatings (1)
- Aluminium alloys (1)
- Aluminum alloy (1)
- Aluminum alloys (1)
- Amorphization (1)
- Amorphous silica (1)
- Annealing (1)
- Aquifer (1)
- BTEX (1)
- Biaxial strength (1)
- Bimodal distribution (1)
- Binder jetting (1)
- Bio Ceramic (1)
- Biogeochemistry (1)
- Bitter technique (1)
- Bone regeneration (1)
- Borosilicate glass (1)
- Bravais lattice (1)
- Brown-rot fungi (1)
- CCS (1)
- CCUS, supercritical/dense phase CO2, carbon steels, martensitic steel, superaustenite steel, droplet corrosion (1)
- Calcium Cobaltite (1)
- Calcium cobaltite (1)
- Carbon steel (1)
- Carbon storage (1)
- Ccs (1)
- Ceramic (1)
- Chemometrics (1)
- Co2-Storage (1)
- Coating (1)
- Cobald based alloy (1)
- Coniophora puteana (1)
- Coordinate measurement machine (1)
- Corrosion (1)
- Corrosion Fatigue (1)
- CrN/NbN (1)
- Crack healing (1)
- Crack propagation (1)
- Creep mechanisms (1)
- Critical energy release rate (1)
- Crystallographic texture (1)
- Cupriavidus metallidurans (1)
- Deformation (1)
- Dentine (1)
- Destabilization (1)
- Diffraction contrast (1)
- Diffusion (1)
- Digital image correlation (1)
- Dislocation (1)
- Dynamic recrystallization (1)
- EFTEM (1)
- Early stages (1)
- Efficiency (1)
- Electric conductivity (1)
- Electrical resistance (1)
- Electron back-scattered diffraction (1)
- Electron microscopy (1)
- Enamel (1)
- End of life (1)
- Environmental stress cracking (ESC) (1)
- Environmentally assisted cracking (1)
- Epoxy resin (1)
- Expanding cavity model (1)
- FIB Tomography (1)
- Failure rate (1)
- Femtosecond laser (1)
- Fiber-matrix interface (1)
- Filters (1)
- Finland (1)
- Fluoride nanoparticles (1)
- Fluorolytic sol−gel (1)
- Fourier series (1)
- Fourier transform infrared spectroscopy (1)
- Fracture mechanics (1)
- Friction (1)
- Friction stir processing (1)
- Full notch creep test (FNCT) (1)
- Fungi (1)
- GMR (1)
- GMR sensors (1)
- Geometrical factors (1)
- Glass capillaries (1)
- Glass crystallization stress (1)
- Glass transition (1)
- Glass-ceramics definition (1)
- Gold (1)
- Grade S960QL steel (1)
- Gradient-enhanced fatigue model (1)
- Grain Boundary Corrosion (1)
- Graphite (1)
- Heat treatment (1)
- High Cycle Fatigue (1)
- High interstitial austenitic steel (1)
- High-temperature corrosion (1)
- Hipims (1)
- Hot isostatic pressing (HIP) (1)
- Hydrogen storage (1)
- Impact wear (1)
- In situ diffraction (1)
- In-situ SEM micro shear deformation (1)
- Inconel 625 (1)
- Indentation (1)
- Indentation hardness (1)
- Interdiffusion (1)
- Interface (1)
- Interfacial shear strength (1)
- Internal Sulfidation (1)
- Internal friction (1)
- Kikuchi pattern (1)
- Laboratory X-ray diffraction (1)
- Laser scanning microscopy (LSM) (1)
- Lattice parameters (1)
- Lifetime prediction (1)
- Light curing (1)
- Log-normal distribution (1)
- Long-term calculation (1)
- Low carbon steel (1)
- Magnetic domain distribution (1)
- Magnetic stray field (1)
- Magnetic stray fields (1)
- Magnetomechanical effect (1)
- Mars (1)
- Martensite (1)
- Martensitic transformation (1)
- Mass transport (1)
- Master curve (1)
- Material modeling (1)
- Metal Magnetic Memory (1)
- Metal magnetic memory (1)
- Microplastics (1)
- Microsegregation (1)
- Microstructur (1)
- Microstructure and texture (1)
- Microstructure evolution (1)
- Microwave technology (1)
- Misorientation (1)
- Mobility (1)
- Modeling (1)
- Molecular dynamics (1)
- Multiaxial deformation (1)
- Multilayer (1)
- NGS (1)
- Nano-scratch test (1)
- Nanoparticle structure (1)
- Nanoscale multilayers (1)
- Natural silver wires (1)
- Near Infrared Spectroscopy (1)
- NiTi (1)
- Notch (1)
- Number density (1)
- Optical centrifugation (1)
- Orientation (1)
- Orientation refinement (1)
- Oxidation (1)
- Oxide coatings (1)
- Oxyfuel (1)
- PLS-DA (1)
- PV modules (1)
- Passive components and circuits (1)
- Permeability (1)
- Phase-field (1)
- Photocleavable organosilanes (1)
- Photopolymer composites (1)
- Phototrophs (1)
- Photovoltaic modules (1)
- Phytolith (1)
- Polymer (1)
- Polymer matrix composites (1)
- Polymeric Materials (1)
- Polypropylene (1)
- Polystyrene (1)
- Porcelain (1)
- Porosity (1)
- Powdered activated carbon (1)
- Power factor (1)
- Preceramic polymer (1)
- Precipitation (1)
- Pressure-assisted sintering (1)
- Production scatter (1)
- Pull-out composite materials (1)
- Raman spectroscopy (1)
- Real-time qPCR (1)
- Relaxation (1)
- Resistance stress (1)
- Rhodonia placenta (1)
- Roughness (1)
- S-Phase (1)
- SEM (1)
- SEM wood characterization (1)
- SLM (1)
- Safety assessment (1)
- Sand blasting (1)
- Scanning acoustic microscopy (SAM) (1)
- Scanning electron microscopy (1)
- Scanning transmission electron microscopy (STEM) (1)
- Segregation (1)
- Self-Assembly (1)
- Sewage treatment plant (1)
- Shape memory alloys (1)
- Shear load (1)
- Shear testing (1)
- Single crystal superalloys (1)
- Single fiber pull-out test (1)
- Sliding simulation (1)
- Slow crack growth (SCG) (1)
- Slurry optimization (1)
- Soil (1)
- Solar panels (1)
- Solid-State-Synthesis (1)
- Solid-state-synthesis (1)
- Sorption (1)
- Spray drying (1)
- Steam oxidation resistance (1)
- Steel P92 (1)
- Stereoscopy (1)
- Strain difference (1)
- Stress-strain-behavior (1)
- Structural steel (1)
- Sulfidation (1)
- Sulphidation (1)
- Superalloy single crystals (1)
- Superconducting magnet (1)
- Support configurations (1)
- Support vector machines (1)
- Surface modification (1)
- Surface nucleation (1)
- Synchrotron X-ray diffraction (1)
- T1 precipitate (1)
- TIG-welding (1)
- Thermal expansion (1)
- Thermo-mechanical loading (1)
- Thermoanalysis (1)
- Thermoelectric oxide (1)
- Thermoelectric oxides (1)
- Thermoelectrics (1)
- Thermogravimetry (1)
- Thickening (1)
- Thin tribofilm (1)
- Titanium (1)
- Tooth wear (1)
- Topography (1)
- Transmission electron microscopy (1)
- Transmittance (1)
- Tricalcium Phosphate (1)
- Vacancies (1)
- Vickers indentation (1)
- Viscoplasticity (1)
- Visualization (1)
- Volume fraction (1)
- Water (1)
- Water droplet erosion resistance (1)
- Wood protection (1)
- X-ray computed tomography (CT) (1)
- Young`s modulus (1)
Organisationseinheit der BAM
- 5 Werkstofftechnik (70) (entfernen)
A femto-second pulsed laser ablation in liquid (PLAL) procedure for the generation of titanium oxide nanoparticles (NP) is reported with the purpose of understanding morphology and structure of the newly generated NPs. Ablation duration was varied for optimization of NP generation processes between 10 and 90 min. Surface morphology of NPs as well as their size and shape (distribution) were analysed by various complementary electron microscopy techniques, i.e. SEM, TSEM and TEM. The crystalline structure of titanium oxide particles was investigated by XRD(two instruments operated in different geometries) and HR-TEM. Concentration of generated titanium oxide NPs in liquid was analysed by ICP-MS. A mix of crystalline (mainly anatase), partly crystalline and amorphous spherical titanium oxide NPs can be reported having a mean size between 10 and 20 nm, which is rather independent of the laser ablation (LA) duration. A second component consisting of irregularly shaped, but crystalline titanium oxide nanostructures is co-generated in the LA water, with more pronounced occurrence at longer LA times. The provenance of this component is assigned to those spherical particles generated in suspension and passing through the converging laser beam, being hence subject to secondary irradiation effects, e. g. fragmentation.
(Bio)geochemical cycling of gold (Au) has been demonstrated in present-day (semi)-arid, (sub)-tropical and temperate environment. Hereby biofilms on Au-bearing mineral- and Au-particle surfaces drive Au dispersion and reconcentration, thereby (trans)forming the particles. However, it is unknown if biogeochemical cycling of Au occurs in polar environments, where air temperatures can reach −40 °C and soils remain frozen for much of the year. Therefore, placer Au-particles, soils and waters were collected at two placer mining districts in arctic Finland, i.e., the Ivalojoki and Lemmenjoki goldfields. Sites were chosen based on contrasting settings ((glacio)-fluvial vs. glacial-till deposits) and depths (surface to 5m below current surface). Gold particles were studied using a combination of tagged 16S rRNA gene next generation sequencing and electron microscopic/microanalytical techniques. Across all sites a range of Au-particle morphologies were observed, including morphotypes indicative of Au dissolution and aggregation. Elevated Au concentrations indicative of Au mobility were detected in placer particle bearing soils at both districts. Typically Au-particles were coated by polymorphic biofilm layers composed of living and dead cells embedded in extracellular polymeric substances. Intermixed were biominerals, clays and iron-sulfides/oxides and abundant secondary Au morphotypes, i.e., nano-particles, microcrystals, sheet-like Au, branched Au networks and overgrowths and secondary rims. Biofilms communities were composed of Acidobacteria (18.3%), Bacteroidetes (15.1%) and Proteobacteria (47.1%), with β-Proteobacteria (19.5%) being the most abundant proteobacterial group. Functionally, biofilms were composed of taxa contributing to biofilm establishment, exopolymer production and nutrient cycling, abundant taxa capable of Au mobilization, detoxification and biomineralization, among them Cupriavidus metallidurans, Acinetobacter spp. and Pseudomonas spp., were detected. In conclusion, these results demonstrate that placer Au-particle transformation and Au dispersion occur in cold, arctic environments. This corroborates the existence of biogeochemical Au cycling in present-day cold environments.
Degradation of AISI 630 exposed to CO2-saturated saline aquifer at ambient pressure and 100 bar
(2018)
In general high alloyed steels are suitable as pipe steels for carbon capture and storage technology (CCS), because they provide sufficient resistance against the corrosive environment of CO2-saturated saline aquifer which serves as potential CCS-site in Germany. High alloyed martensitic steel AISI 630 has been proven to be sufficient resistant in corrosive environments, e.g. regarding heat, pressure, salinity of the aquifer, CO2-partial pressure), but reveals a distinct corrosion pattern in CCS environment. Therefore coupons of AISI 630 heat treated using usual protocols were kept at T=60 °C and ambient pressure as well as p=100 bar up to 8000 h in an a) water saturated supercritical CO2 and b) CO2-saturated synthetic aquifer environment similar to on-shore CCS-sites in the Northern German Basin. AISI 630 precipitates a discontinuous ellipsoidal corrosion layer after being exposed for more than 4000 hours. Best corrosion resistance in the CO2-saturated synthetic aquifer environment phase is achieved via normalizing prior to exposure. In water saturated supercritical CO2 tempering at medium temperatures after hardening gives lowest corrosion rates. Corrosion fatigue via push-pull tests with a series of 30 specimens was evaluated at stress amplitudes between 150 MPa and 500 MPa (sinusoidal dynamic test loads, R=-1; resonant frequency ~ 30 Hz). The endurance limit of AISI 630 is reduced by more than 50% when exposed to CCS environment (maximum number of cycles (10 x 106) at a stress amplitude of 150 MPa).
The research focus of this study was set on the corrosion process of condensate as droplets on the surface of carbon steels (X52, X70) martensitic steel UNS S41500, and super austenite UNS N08031 in CO2 atmosphere with impurities at 278 K (to simulate the offshore transportation condition in a buried pipeline). The possibility of dew/droplet formation on the steel surface and wetting behavior of corresponding materials were evaluated by contact angle measurement in dense CO2 at 278 K. To observe the effect of impurities (SO2 and O2) on droplet corrosion process, exposure tests were carried out in the mixed atmosphere with a drop, 1 ‑ 10 µL in volume, of CO2 saturated ultra-pure water on steel surface. Comparable exposure tests were carried out with the same gas mixture and the same volume of water, as vapor, to observe the droplet formation and the corrosion process that follows. Effects of surface roughness on the droplet formation and its corrosion process were further studied and showed no significant role upon long time exposure. The results from droplet experiments were compared to those from the bulk electrolyte for the further recommendation on the quality control of gas stream along with the use of carbon steels as transport pipelines in CCS - Carbon Capture and Storage system.
A gray cast iron disc, which had been submitted to a heavy duty automotive brake test, was examined with energy filtered transmission electron microscopy. A graphite flake in a convenient angular position showed the shear interaction of graphite layers with the iron matrix in nano-scale resolution. Atomic layers of graphite were wedged into the ferritic bulk, allowing the entrance of oxygen and the subsequent formation of magnetite. The exfoliated few-layer graphene batches deformed heavily when forced into the matrix. When Raman spectra from the disc surface, which show distinctive carbonaceous bands, were compared with Raman spectra from graphite subjected to deformation in a shaker mill with different milling times, it could be seen that the shear stress on the brake surface was much more effective to induce disorder than the milling, where compressive and impact forces had been additionally exerted on the sample. During shear load the high anisotropy of elastic modulus in the graphite crystalline structure and the low adhesion between graphite basal planes allowed the exfoliation of wrinkled few-layer grapheme batches, causing the formation of more defect related Raman bands than the mechanical stress during high-energy milling.
Hydrogen is an attractive energy carrier that requires high effort for safe storage. For ensuring safety, storage cylinders must undergo a challenging approval process. Relevant standards and regulations for composite cylinders used for the transport of hydrogen and for its onboard storage are currently based on deterministic (e.g. ISO 11119-3) or to some respect semi-probabilistic criteria (UN GTR No. 13; with respect to burst strength).
This paper provides a systematic analysis of the load cycle properties resulting from these regulations and standards. Their characteristics are compared with the probabilistic approach of the Federal Institute for Materials Research and Testing BAM. The most important aspect of comparing different concepts is the rate for accepting designs with potentially unsafe or critical safety properties. This acceptance rate is analysed by operating Monte-Carlo simulations over the available range of production properties.
Microplastics are increasingly entering marine, limnic and terrestrial ecosystems worldwide, where they sorb hydrophobic organic contaminants. Here, the sorption behavior of the fuel-related water contaminants benzene, toluene, ethyl benzene and xylene (BTEX) and four tertiary butyl ethers to virgin and via UV radiation aged polypropylene (PP) and polystyrene (PS) pellets was investigated. Changes in material properties due to aging were recorded using appropriate polymer characterization methods, such as differential scanning calorimetry, Fourier transform infrared spectroscopy, gel permeation chromatography, X-ray photoelectron spectroscopy, and microscopy.
Pellets were exposed to water containing BTEX and the ethers at 130-190 mg/L for up to two weeks.
Aqueous sorbate concentrations were determined by headspace gas chromatography. Sorption to the polymers was correlated with the sorbate's Kow and was significant for BTEX and marginal for the ethers.
Due to substantially lower glass transition temperatures, PP showed higher sorption than PS. Aging had no effect on the sorption behavior of PP. PS sorbed less BTEX after aging due to an oxidized surface layer.
The increasing pollution of terrestrial and aquatic ecosystems with plastic debris leads to the accumulation of microscopic plastic particles of still unknown amount. To monitor the degree of contamination analytical methods are urgently needed, which help to quantify microplastics (MP). Currently, time-costly purified materials enriched on filters are investigated both by micro-infrared spectroscopy and/or micro-Raman. Although yielding precise results, these techniques are time consuming, and are restricted to the analysis of a small part of the sample in the order of few micrograms. To overcome these problems, here we tested a macroscopic dimensioned NIR process-spectroscopic method in combination with chemometrics. For calibration, artificial MP/soil mixtures containing defined ratios of polyethylene, polyethylene terephthalate, polypropylene, and polystyrene with diameters < 125 µm were prepared and measured by a process FT-NIR spectrometer equipped with a fiber optic reflection probe. The resulting spectra were processed by chemometric models including support vector machine regression (SVR), and partial least squares discriminant analysis (PLS-DA). Validation of models by MP mixtures, MP-free soils and real-world samples, e.g. and fermenter residue, suggest a reliable detection and a possible classification of MP at levels above 0.5 to 1.0 mass% depending on the polymer. The benefit of the combined NIRS chemometric approach lies in the rapid assessment whether soil contains MP, without any chemical pre-treatment. The method can be used with larger sample volumes and even allows for an online prediction and thus meets the demand of a high-throughput method.
Wood treated with nano metal fluorides is found to resist fungal decay. Sol−gel synthesis was used to synthesize MgF2 and CaF2 nanoparticles. Electron microscopy images confirmed the localization of MgF2 and CaF2 nanoparticles in wood. Efficacy of nano metal fluoride-treated wood was tested against brown-rot fungi Coniophora puteana and Rhodonia placenta. Untreated wood specimens had higher
mass losses (∼30%) compared to treated specimens, which had average mass loss of 2% against C. puteana and 14% against R. placenta, respectively. Nano metal fluorides provide a viable alternative to current wood preservatives.
Commercial grade-1 titanium samples (Ti, 99.6%) were treated using three alternative methods, (i) femtosecond laser processing, (ii) thermal heat treatment, and (iii) electrochemical anodization, respectively, resulting in the formation of differently conditioned superficial titanium oxide layers. The laser processing (i) was carried out by a Ti:sapphire laser (pulse duration 30 fs, central wavelength 790 nm, pulse repetition rate 1 kHz) in a regime of generating laser-induced periodic surface structures (LIPSS). The experimental conditions (laser fluence, spatial spot overlap) were optimized in a sample-scanning setup for the processing of several square-millimeters large surface areas covered homogeneously by these nanostructures. The differently oxidized titanium surfaces were characterized by optical microscopy, micro Raman spectroscopy, variable angle spectroscopic ellipsometry, and instrumented indentation testing. The tribological performance was characterized in the regime of mixed friction by reciprocating sliding tests against a sphere of hardened steel in fully formulated engine oil as lubricant. The specific tribological performance of the differently treated surfaces is discussed with respect to possible physical and chemical mechanisms.