5 Werkstofftechnik
Filtern
Dokumenttyp
- Vortrag (431)
Sprache
- Englisch (332)
- Deutsch (96)
- Mehrsprachig (3)
Referierte Publikation
- nein (431) (entfernen)
Schlagworte
- Additive Manufacturing (38)
- Additive manufacturing (24)
- Microstructure (21)
- Corrosion (20)
- Glass (18)
- Ontology (17)
- Fatigue (13)
- Ceramics (12)
- LCF (11)
- 316L (10)
- Additive Fertigung (10)
- Creep (10)
- Ontologie (10)
- Transmission electron microscopy (10)
- Crack growth (9)
- Fraktographie (9)
- Sintering (9)
- Ceramic (8)
- Thermoelectrics (8)
- Diffraction (7)
- Fractography (7)
- Machine Learning (7)
- Particle size (7)
- Powder (7)
- Ti-6Al-4V (7)
- CCUS (6)
- DCB (6)
- Digitalisierung (6)
- EBSD (6)
- Glas (6)
- High entropy alloys (6)
- Low Cycle Fatigue (6)
- Mikrostruktur (6)
- Scanning electron microscopy (6)
- Zugversuch (6)
- 3D printing (5)
- AGIL (5)
- Aluminium (5)
- Anisotropy (5)
- Crystal plasticity (5)
- Crystallization (5)
- Glass fiber reinforced polymers (5)
- In situ (5)
- Microgravity (5)
- Oxidation (5)
- Slurry (5)
- VSSA (5)
- Water speciation (5)
- AISI 316L (4)
- Alloy 2618A (4)
- CALPHAD (4)
- CCS (4)
- CO2 (4)
- Coarsening (4)
- Creep behavior (4)
- Degradation (4)
- Droplet corrosion (4)
- EN AW-2618A (4)
- FAIR (4)
- FAIR data management (4)
- Fatigue crack growth (4)
- Fe-Al alloys (4)
- Foaming (4)
- High-temperature corrosion (4)
- In-space manufacturing (4)
- Intermetallics (4)
- Iron aluminides (4)
- Kriechen (4)
- Laser powder bed fusion (4)
- Layerwise slurry deposition (4)
- Martensitic steel (4)
- Mechanical properties (4)
- Nano (4)
- Nano powder (4)
- Neutron diffraction (4)
- Nickel-base superalloys (4)
- Non-destructive testing (4)
- Normung (4)
- Plattform MaterialDigital (4)
- Polymer matrix composites (4)
- Residual Stress (4)
- Semantic Web Technologies (4)
- Sulfidation (4)
- Supercritical/dense phase CO2 (4)
- TMF (4)
- Thermomechanical fatigue (4)
- Vickers (4)
- Wissensrepräsentation (4)
- Alkali ions (3)
- Alumina (3)
- Aluminium Alloy (3)
- Aluminium alloy (3)
- Betriebsfestigkeit (3)
- CCU (3)
- Carbon steels (3)
- Ceramic spring (3)
- Computed Tomography (3)
- Dielectric strength (3)
- Fracture surface (3)
- Full Notch Creep Test (3)
- Gassensorik (3)
- Geothermal (3)
- H2Safety@BAM (3)
- Heat treatment (3)
- High temperature corrosion (3)
- Keramik (3)
- Knowledge graph and ontologies (3)
- Lebensdauer (3)
- Mechanical behavior (3)
- Mechanical testing (3)
- Mikroplastik (3)
- Ni-Resist (3)
- PMD (3)
- Residual stress (3)
- S-phase (3)
- SEM (3)
- Scarf repairs (3)
- Semantic Interoperability (3)
- Silicate Glasses (3)
- Soda-lime silicate glass (3)
- Superaustenite steel (3)
- Tensile Test (3)
- Texture (3)
- Transmission electron microscopy (TEM) (3)
- Wasser (3)
- Water content (3)
- Welding (3)
- Wind turbine blades (3)
- X-ray diffraction (3)
- Zerstörungsfreie Prüfung (3)
- μ-gravity (3)
- Advanced ceramics (2)
- Alkali zinc borate glasses (2)
- Alterung (2)
- Analytische Zentrifuge (2)
- Bildanalyse (2)
- CLS (2)
- CO2 quality (2)
- CT (2)
- Calciumcobaltit (2)
- Calciummanganat (2)
- Carbon capture (2)
- Carbon capture storage (2)
- Carbon dioxide (2)
- Carbon steel (2)
- Characterization (2)
- Chemically complex alloy (2)
- Composite (2)
- Composites (2)
- Concrete (2)
- Copper (2)
- Crack tip opening displacement (2)
- Creep data (2)
- Dark-field transmission electron microscopy (2)
- Data Fusion (2)
- Data Interoperability (2)
- Data mapping (2)
- Datenbank (2)
- Dielectric breakdown (2)
- Diesel (2)
- Diffraction Elastic Constants (2)
- Diffusion (2)
- Digital image correlation (2)
- Digitaler Zwilling (2)
- Digitalization (2)
- Digitization (2)
- Digtial Representation (2)
- Diopside (2)
- Dislocation (2)
- EDXRD (2)
- Electron microscopy (2)
- Electron-beam-induced modification (2)
- Electronic Lab Notebook (2)
- Environmental Stress Cracking (2)
- Environmental stress cracking (2)
- Faser-Kunststoff-Verbunde (2)
- Faserkunststoffverbunde (2)
- Faseroptische Sensorik (2)
- Ferritic-martensitic steels (2)
- Fracture Toughness (2)
- Full-Notch Creep Test (FNCT) (2)
- Geführte Ultraschallwellen (2)
- Gitterkonstanten (2)
- Glass-ceramics (2)
- Hard machining (2)
- High Cycle Fatigue (2)
- High Entropy Alloy (2)
- High Temperature Corrosion (2)
- High temperature (2)
- High temperature mechanical properties (2)
- High-entropy alloy (2)
- High-entropy alloys (2)
- Hochentropie-Legierung (2)
- Hochtemperatur (2)
- Impurities (2)
- In-situ (2)
- Interoperability (2)
- Joined nickel-based alloys (2)
- L-PBF (2)
- Laser (2)
- Laser Powder Bed Fusion (2)
- Laser Powder Bed fusion (2)
- Laser beam melting (2)
- Layerwise (2)
- Leckdetektion (2)
- Lunar regolith simulant (2)
- ML (2)
- Material Digital (2)
- Material digital (2)
- Metrologie zur Wasserstoffspeicherung (2)
- Microplastics (2)
- Microstrucrue Design (2)
- Microstructural analysis (2)
- Microstructure Design (2)
- Mixed gas atmosphere (2)
- Modeling (2)
- Multilayer (2)
- Multilayer technology (2)
- Multilayertechnik (2)
- NDT (2)
- Nano particle (2)
- Nano screening (2)
- Nano-powder (2)
- Nanomaterial (2)
- Nanoparticles (2)
- Nanopulver (2)
- Notches (2)
- OECD TG 124 (2)
- Ontologien (2)
- Ontology development (2)
- Orientation (2)
- Oriented surface crystallization (2)
- Oxidation behavior (2)
- Oxide Glasses (2)
- Oxidglas (2)
- PBF-LB/M/316L (2)
- PE-HD (2)
- PMD Core Ontology (2)
- PMDco (2)
- Partikelgrößenverteilung (2)
- Phase-field simulation (2)
- Phasenidentifikation (2)
- Pipeline (2)
- Plattform Material Digital (2)
- Polyethylen (2)
- Polyethylen hoher Dichte (2)
- Polymer Matrix Composites (2)
- Process monitoring (2)
- Push-out Test (2)
- REM (2)
- Reaction sintering (2)
- Residual Stresses (2)
- Ressidual stress (2)
- Rotor blade (2)
- Sandwich (2)
- Scale-bridging (2)
- Schadensanalyse (2)
- Schädigung (2)
- Selective Laser Melting (2)
- Semantic Representation (2)
- Semantic Web (2)
- Semantisches Web (2)
- SensRef (2)
- Silicon Carbide (2)
- Silver diffusion (2)
- Silver-glass-metallization-paste (2)
- Simulation (2)
- Sinter additive (2)
- Sintering additives (2)
- Sintern (2)
- Spannungsriss (2)
- Spectroscopy (2)
- Spray drying (2)
- Spring constant (2)
- Standard (2)
- Standardisierung (2)
- Standardization (2)
- Structural Health Monitoring (SHM) (2)
- Superlegierung (2)
- Surface energy (2)
- TED-GC-MS (2)
- TEM (2)
- Tensile Test Ontology (2)
- Tensile data (2)
- Tensile test (2)
- Thermo-Mechanical Fatigue (2)
- Thermoelectric (2)
- Ti64 (2)
- TiAl5V4 (2)
- Titan (2)
- Topographie (2)
- Topography (2)
- UV-irradiation (2)
- Ultrasound (2)
- Virtual experiments (2)
- Viscoplasticity (2)
- Viscosity (2)
- Wall thickness (2)
- Wind turbine blade shells (2)
- Windenergie (2)
- XANES (2)
- XRD (2)
- Zero-g (2)
- Zugeigenschaften (2)
- robotische Glasschmelzanlage (2)
- µ-gravity (2)
- 3D (1)
- 3D Druck (1)
- 3D REM (1)
- 3D Reconstruction (1)
- 3D glass structure model (1)
- 3D materialography (1)
- 3D-printing (1)
- 9-12% Cr ferritic-martensitic steels (1)
- 9–12%Cr steel (1)
- AFM based test methods (1)
- AM (1)
- Accelerated integration scheme (1)
- Acids (1)
- Active thermography (1)
- Additiv gefertigter Stahl (1)
- Adiabatic shear bands (1)
- Advanced manufacturing (1)
- Aerospace (1)
- Age hardening (1)
- Ageing (1)
- Agglomerates (1)
- Aggressive gases (1)
- Aging (1)
- Air-coupled ultrasonic testing (1)
- Airborne ultrasonic testing (1)
- Al-Li alloys (1)
- Alkali zinc borate glass (1)
- Aluminum (1)
- Aluminum alloys (1)
- Analyse (1)
- Analysis (1)
- Analytik (1)
- Annealing (1)
- Atmospheric plasma spraying (1)
- Aussonderugnsrate (1)
- Austenitic cast iron (1)
- Austenitic steel 316L (1)
- Automatable digital approach (1)
- Automation (1)
- BET (1)
- Biaxial strength (1)
- Binder jetting (1)
- Bioactive (1)
- Bioactive Glass (1)
- Bioceramics (1)
- Biodiesel (1)
- Blähen (1)
- Bond energy (1)
- Breakdown strength (1)
- Brinell hardness (1)
- Bruchflächen (1)
- Bruchflächenanalyse (1)
- Bruchflächenauswertung (1)
- Bundesoberbehörden (1)
- CFK (1)
- CO2-corrosion (1)
- Calcination (1)
- Calcium cobaltite (1)
- Calcium manganate (1)
- Calcium sulfates (1)
- Calibration (1)
- Cantor alloy (1)
- Capture (1)
- Carbon (1)
- Carbon steels (1)
- Carbon Capture (1)
- Carbon Capture, Utilization and Storage (CCUS) (1)
- Carbon Fiber Reinforced Plastics (1)
- Carbon Fibers (1)
- Casting (1)
- Centrifugal casting (1)
- Ceramic multilayer (1)
- Ceramic springs (1)
- Certification Standard 22 (1)
- Certified Referencematerial (1)
- Cetrifugal Liquid Sedimentation CLS (1)
- Chemically complex alloys (1)
- Chemo-mechanical coupling (1)
- Chromatography (1)
- Chromia (1)
- Chromium oxide (1)
- Co-firing (1)
- Co-segregation (1)
- Coatings (1)
- Complex borides (1)
- Complex loading (1)
- Component assessment (1)
- Composite testing (1)
- Compositionally complex alloys (1)
- Computed tomography (1)
- Condensation (1)
- Contamination (1)
- Continnum damage model (1)
- Cooling simulations (1)
- Cow stress (1)
- Cr2O3 (1)
- Crack (1)
- Crack Propagation (1)
- Crack evolution (1)
- Crack propagation (1)
- Creep anisotropy (1)
- Creep behaviour (1)
- Creep-Fatigue (1)
- Creep-fatigue (1)
- Crevice corrosion (1)
- Cross linking (1)
- Crystal Defects (1)
- Crystal Orientation (1)
- Crystal Plasticity Modelling (1)
- Cubical Iron Oxide (1)
- Cure process (1)
- Cycle jump (1)
- Cyclic R-Curve (1)
- Cyclic oxidation (1)
- Cyclic softening (1)
- DIN (1)
- DLS (1)
- Damage (1)
- Damage Behavior (1)
- Damage Tolerance (1)
- Damage behavior (1)
- Damage mechanisms (1)
- Dark-field transmission electron microscopy (DFTEM) (1)
- Data Exchange (1)
- Data Management (1)
- Data Structures (1)
- Data linking (1)
- Data management (1)
- Data pipeline concept (1)
- Data space (1)
- Data storage (1)
- Data structure (1)
- Datenökosystem (1)
- Deep learning (1)
- Defects (1)
- Defects phase diagram (1)
- Defects thermodynamics (1)
- Deformation behavior (1)
- Dehnungsfehler (1)
- Density (1)
- Density-based Thermodynamics (1)
- Density-based model (1)
- Density-based phase-field modelling (1)
- Dental (1)
- Destabilization (1)
- Die casting (1)
- Dielectric breakdown strength (1)
- Dielectric characterization (1)
- Diffraction Enhanced Imaging (1)
- Diffraction contrast (1)
- Diffusion coefficient (1)
- Digital representation (1)
- Digital workflow (1)
- Dislocation substructure (1)
- Dislocations (1)
- Disordered assemblies (1)
- Dispersion process (1)
- Dissimilar metal weld (1)
- Dissolved water (1)
- Distribution function (1)
- Driving physical mechanism (1)
- Dual-energy (1)
- Durchschlagfestigkeit (1)
- Dynamic mechanical analysis (1)
- Dynamic mechanical analysis (DMA) (1)
- Dynamisch Mechanische Analyse (1)
- EAC-1A (1)
- EASA (1)
- EDX (1)
- EN AW 2618A (1)
- Early oxidation (1)
- Eigenspannung (1)
- Elastic constants (1)
- Electric field distribution (1)
- Electric field strength (1)
- Electrical insulation (1)
- Electron Backscatter Diffraction (1)
- Electron Microscopy (1)
- Electron backscatter diffraction (1)
- Electron backscattered diffraction (EBSD) (1)
- Elektronisches Laborbuch (ELN) (1)
- Energy harvesting (1)
- Entwicklung (1)
- Environmental Stress Cracking (ESC) (1)
- Ermüdung (1)
- Ermüdungsriss (1)
- Erneuerbare Energien (1)
- Etching (1)
- Extensometer (1)
- FAIR Data Management (1)
- FAIR data (1)
- FCH JU (1)
- FIB (1)
- Fabrication method (1)
- Fahrrad (1)
- Failure test (1)
- Faser (1)
- Faseroptik (1)
- Faserverstärkte Kunstoffe (1)
- Fatigue Crack Growth (1)
- Fatigue Life Evaluation (1)
- Fatigue damage (1)
- Fatigue fracture (1)
- Fatigue of sandwich shell structures (1)
- Fatigue of sandwich structures (1)
- Fatigue performance (1)
- FeCr- alloys (1)
- Federkonstante (1)
- Feldspar (1)
- Fem (1)
- Ferritic Alloys (1)
- Ferroelectret (1)
- Ferroelektret (1)
- Fertigungstechnologie (1)
- Festigkeit (1)
- Fiber (1)
- Fiber reinforced polymer (1)
- Fiber reinforced polymers (1)
- Fine Powder (1)
- Finite element analysis (1)
- Finite elmenet simulation (1)
- Flowability (1)
- Fluorescence spectroscopy (1)
- Focused Ion Beam (1)
- Foliengießen (1)
- Force-distance diagram (1)
- Formerkennung (1)
- Fracture Mechanics (1)
- Fracture Surface Analysis (1)
- Fracture behavior (1)
- Fracture surface analysis (1)
- Fracture toughness (1)
- Freeze Drying (1)
- GC-MS (1)
- GD-OES (1)
- Gas storage (1)
- Gasabgabe (1)
- Gasgehalt (1)
- Gasturbinen (1)
- Gefüge (1)
- General Aviation (1)
- Geopolymers (1)
- Gitterfehlpassung (1)
- Glasmatrixkomposit (1)
- Glass Fibres (1)
- Glass composition (1)
- Glass fibre reinforced plastics (1)
- Glass melting (1)
- Glass powder (1)
- Glass screening device (1)
- Gold nanoparticle synthesis (1)
- Gold nanoparticles (1)
- Gradient-enhanced damage (1)
- Grain boundaries (1)
- Grain boundary engineering (1)
- Granules (1)
- Granulometrie (1)
- Graphic design (1)
- Grünfolieneigenschaften (1)
- HDPE Soprption (1)
- HEA (1)
- HIP (1)
- Hardness (1)
- Hartbearbeitung (1)
- Heat Treatment (1)
- Heat Treatments (1)
- Heißgasextraktion (1)
- Heißgaskorrosion (1)
- High Entropy Alloys (1)
- High Temperature Testing (1)
- High entropy alloy (1)
- High entropy superalloys (1)
- High-Temperature Corrosion (1)
- High-density polyethylene (1)
- Hochentropielegierungen (1)
- Hochspannungsprüfung (1)
- Hochtemperaturbrennstoffzelle (1)
- Hochtemperaturermüdung (1)
- Horizon 2020 (1)
- Hot Press (1)
- Hot isostatic pressing (1)
- Hot pressing (1)
- Hydrogen (1)
- Hydrogen permeation (1)
- Hydrogen sensor (1)
- Hydrogen sensors (1)
- Hyper-arid (1)
- IN 718 (1)
- IN738LC (1)
- IR (1)
- ISRU (1)
- Implant failures (1)
- Implants (1)
- In situ tensile test (1)
- In-Situ Testing (1)
- Inconel 686 coating (1)
- Inconel 718 (1)
- Infrastructure (1)
- Initial attachment (1)
- Injection (1)
- Interface (1)
- Interface Strength (1)
- Interfacial Spinodal (1)
- Internal friction (1)
- Inverse ostwald ripening (1)
- Investment casting (1)
- Iron oxide nanoparticles (1)
- Kalzinierung (1)
- Kavitation (1)
- Kennwertermittlung (1)
- Keramikfeder (1)
- Keramische Folien (1)
- Klebung (1)
- Kleinprobenprüfung (1)
- Knowledge Graphs (1)
- Knowledge Representation (1)
- Knowledge graph (1)
- Kontrastierung (1)
- Korrosion (1)
- Kriechversuche (1)
- Kristallisation (1)
- Kunststoffe (1)
- Kupfer (1)
- Kurzzeitfestigkeit (1)
- L-PBF 316L (1)
- LSD-print (1)
- LTCC (1)
- Laminography (1)
- Laser Poeder Bed Fusion (1)
- Laser Scanning Microscopy (LSM) (1)
- Laser cladding (1)
- Laser curing (1)
- Laser induced slipcasting (1)
- Laserbearbeitung (1)
- Laserscanningmikroskopie (LSM) (1)
- Lattice misfit (1)
- Layer depostion (1)
- Layer system (1)
- Layerwise Slurry Deposition (1)
- Legierung mit komplexer Zusammensetzung (1)
- Li-ion battery (1)
- Life cycle (1)
- Lightweight materials (1)
- Lightweighting (1)
- Lithium Ion Batteries (1)
- Localized plasmons (1)
- Long-term storage (1)
- Low cycle fatigue (1)
- Low-Cycle-Fatigue (1)
- Low-cycle-fatigue behaviour (1)
- Luftultraschall (1)
- Lunar habitat (1)
- Lösungsmittel (1)
- MEA (1)
- Manganese oxide (1)
- Manufacturing (1)
- Martensitic steel (1)
- Mat-o-lab (1)
- Material Life Cycle (1)
- Material defects (1)
- MaterialDigital (1)
- Materialcharakterisierung (1)
- Materialentwicklung (1)
- Materialmodell (1)
- Materials Data Space (1)
- Materials Modelling (1)
- Materials Science (1)
- Materials and Processes Data Reusability (1)
- Materials science (1)
- Materials testing (1)
- Materialwissenschaft (1)
- Matrix (1)
- Mechanical and thermal testing (1)
- Mechanische Eigenschaften (1)
- Mechanisches Verhalten (1)
- Mechanistic Modelling (1)
- Medium Entropy Alloys (1)
- Medium entopy alloy (1)
- Medium-entropy alloy (1)
- Melt pool boundary (1)
- Metadata schema (1)
- Metallic components (1)
- Metallic silver precipitates (1)
- Metallography (1)
- Metrologie (1)
- Micro-shrinkages (1)
- Microbiologically influenced corrosion (1)
- Microhardness (1)
- Micromechanical model (1)
- Microstructural characterization (1)
- Microstructural evolution (1)
- Microstructural orientation (1)
- Microstructure Characterization (1)
- Microstructure Evolution (1)
- Microstructure characterisation (1)
- Microstructure design (1)
- Microstructure evolution (1)
- Microstructure modification (1)
- Microstructure-property-correlation (1)
- Mid-Level Ontology for MSE (1)
- Mikro-Computertomographie (1)
- Mikrogravitation (1)
- Mikrostrukturentwicklung (1)
- Mindedestberstdruck (1)
- Mixed Ca-K-Na phosphates (1)
- Mn3O4 (1)
- Modell (1)
- Monte-Carlo Simulation (1)
- Mortar (1)
- Mortel (1)
- Multi-principal element alloys (1)
- Multiaxial stress state (1)
- NTE (1)
- Na and K rhenanites (1)
- Nano material (1)
- Nano-assemblies (1)
- Nanoparticle synthesis (1)
- Nanopartikel (1)
- Nanoplattform (1)
- Negative charged microparticle (1)
- Neutron Diffraction (1)
- New standards (1)
- Nickel-base superalloy (1)
- Non-desired foaming (1)
- Nondestructive testing (1)
- Nucleation (1)
- Nucleation mode (1)
- OECD TG (1)
- Oberflächenaktive wässrige Medien (1)
- Online quality control (1)
- Ontologies (1)
- Ooxidation (1)
- Optic (1)
- Overaging (1)
- Oxide glass (1)
- P92 (1)
- P92 steels (1)
- PA6.6 (1)
- PPA (1)
- Parametric modeling (1)
- Particle size determination (1)
- Partikelgröße (1)
- Patent (1)
- Paving (1)
- Phase Diagrams (1)
- Phase Separation (1)
- Phase analysis (1)
- Phase diagram (1)
- Phase field simulation (1)
- Phase separation (1)
- Phase transformation (1)
- Phase transformations (1)
- Phase-Field Simulation (1)
- Phase-Field Simulations (1)
- Phase-field Simulation (1)
- Photon counting detector (1)
- Physically based material model (1)
- Physics-informed Neural Network (1)
- Pipeline network (1)
- Planetary surface (1)
- Platform Material Digital (1)
- Platform Material Digital (PMD) (1)
- Platform MaterialDigital (1)
- Platform MaterialDigital (PMD) (1)
- Plattform Material Digital (PMD) (1)
- Pole figures (1)
- Polyaniline (1)
- Polyethylene, PE-HD (1)
- Polymer (1)
- Polymer Matrix Composite (1)
- Polymerwissenschaften (1)
- Porcelain (1)
- Pores (1)
- Powder deposition (1)
- Power plant (1)
- Precipitates (1)
- Precipitation (1)
- Precipitation Analysis (1)
- Precipitation hardening (1)
- Preparation (1)
- Pressure assisted sintering (1)
- Pressure-assisted sintering (1)
- Probengrößeneffekt (1)
- Protective coating (1)
- Präparation (1)
- Pull-out (1)
- Pycnometry (1)
- Quantitative Precipitation Analysis (1)
- Quantitative image analysis (1)
- Rafting (1)
- Recommendations (1)
- Recycling (1)
- Reference data (1)
- Reference material (1)
- Referenzdaten (1)
- Refractory chemically complex alloy (1)
- Refractory chemically complex alloys (1)
- Regelwerke (1)
- Relaxation (1)
- Relaxation metallic glasses (1)
- Relaxationsphänomene (1)
- Repair of sandwich shell structures (1)
- Reproducibility (1)
- Research Data Management (1)
- Residual stress analysis (1)
- Residual stresses (1)
- Resistance (1)
- Restberstfestigkeit (1)
- Review (1)
- Rissentwicklung (1)
- Rissheilung (1)
- Risswachstum (1)
- Roboter (1)
- Robotic melting (1)
- Robotische Schmelzanlage (1)
- Rotorblattschalen (1)
- Roughness (1)
- Röntgen-Refraktion (1)
- Röntgenbeugung (1)
- Röntgenrefraktion (1)
- S355 steel sheet (1)
- SHM (1)
- SIMS (1)
- SLM (1)
- Safety assessment (1)
- Sailplane Development Panel (1)
- Salzschmelzen (1)
- Sample preparation (1)
- Sandwich structures (1)
- Scanning Electron Microscopy (SEM) (1)
- Scanning electron microscope (1)
- Scanning transmission electron microscopy (STEM) (1)
- Scarf joint repair (1)
- Schadensprävention (1)
- Schwerelosigkeit (1)
- Schwingbrüche (1)
- Schwingstreifen (1)
- Screen printing (1)
- Selective laser melting (1)
- Semantic Data (1)
- Semantic Interioerability (1)
- Semantic structuring (1)
- Semantic web (1)
- Semiconductor materials (1)
- Sensor (1)
- SiO2 (1)
- Sibayak (1)
- Silber (1)
- Silicatglas (1)
- Silver cluster (1)
- Silver metallization paste (1)
- Silver precipitates (1)
- Silver-glass metallization paste (1)
- Simulation of concrete (1)
- Single-Crystal (1)
- Single-crystals (1)
- Sintering atmosphere (1)
- Sintertemperatur (1)
- Sinterung (1)
- Size distribution (1)
- Slow Crack Growth (SCG) (1)
- Slow crack growth (1)
- Small-Angle X-ray Scattering (1)
- Soda-lime-silica glass (1)
- Sol-gel coating (1)
- Solar sintering (1)
- Solid solution strengthening (1)
- Space exploration (1)
- Spannungs-Dehnungs-Verhalten (1)
- Spark plasma sintering (1)
- Specific surface (1)
- Spezifische Oberfläche (1)
- Spinodal Decomposition (1)
- Split Hopkinson bar (1)
- Spring constant (1)
- Stainless steel (1)
- Stanzen (1)
- Steel (1)
- Storage (1)
- Strain rate dependence (1)
- Structure (1)
- Structured heating (1)
- Struktur (1)
- Subsurface defects (1)
- Sulfiding (1)
- Superalloy (1)
- Superalloy single crystals (1)
- Superalloys (1)
- Superaustenite steel (1)
- Supercritical/dense phase CO 2 (1)
- Superlegierungen (1)
- Surface (1)
- Surface Energy (1)
- Surface Nucleation (1)
- Surface crystallization (1)
- Surface nucleation (1)
- Symbolik (1)
- Symmetric dwell periods (1)
- Synchrotron CT (1)
- Synchrotron radiation (1)
- Synchrotronstrahlung (1)
- Syngle Crystal alloy (1)
- Synthetic air (1)
- Systematische Schadensanalysen, Prozeduren (1)
- TAHYA (1)
- TED (1)
- TMF experiments (1)
- Temperature (1)
- Temperature driven process (1)
- Temperaturschwankungen (1)
- Tempered Martensite Ferritic Steels (1)
- Tempered martensite ferritic steel (1)
- Tempered martensite ferritic steels (1)
- Tensile Properties (1)
- Tensile stress relaxation (1)
- Tensile testing (1)
- Texturation (1)
- Thermal degradation (1)
- Thermal stress (1)
- Thermische Analyse (1)
- Thermo mechanical fatigue (1)
- Thermo-mechanical fatigue (1)
- Thermo-mechanical-loading (1)
- Thermo-optical measurement (1)
- Thermoanalytical Methods (1)
- Thermoelectric generator (1)
- Thermoelectric oxide (1)
- Thermoelektrika (1)
- Thermoelektrischer Generator (1)
- Thermographie (1)
- Thermogravimetric analysis (1)
- Thermogravimetry (1)
- Thermomechanics (1)
- Thermomechanik (1)
- Thermomechanische Eigenschaften (1)
- Thermoset polymers (1)
- Thesaurus (1)
- Titanium (1)
- Tomography (1)
- Tools (1)
- Transmissionselektronenmikroskopie (1)
- Transparent ceramics (1)
- Two Photon Polymerization (1)
- Ultraschall (1)
- Umgebungsbedingter Spannungsriss (1)
- Under cyclic loading (1)
- Utilization (1)
- Utilization, and storage (CCUS) technology (1)
- VCSEL (1)
- Vacuum hot extraction (1)
- Vernetzung (1)
- Versetzungsstrukturen (1)
- Vickers hardness (1)
- Virtueller Materialdatenraum (1)
- Viscose sintering (1)
- Viskoplastisch (1)
- Wandler (1)
- Waste water (1)
- Water-based (1)
- Weibull Distribution (1)
- Weibull distribution (1)
- Welding processing influences (1)
- Werkstoffdaten (1)
- Werkstoffprüfung (1)
- Whole-chain CCS scenario (1)
- Wind energy (1)
- Wind turbine (1)
- Wind turbine blade shell structures (1)
- Withstand voltage tests (1)
- Workshop (1)
- Wärmespeicher (1)
- X-Ray Diffraction (1)
- X-ray imaging (1)
- X-ray laminography (1)
- X-ray refraction (1)
- XRM (1)
- Zugversuchsontologie (1)
- Zyklische Belastung (1)
- Zyklische R-Kurve (1)
- alumina (1)
- arbon capture (1)
- carbon steel (1)
- ceramic (1)
- ceramics (1)
- condensate (1)
- corrosion (1)
- dental (1)
- dispersion (1)
- electrochemical characterization (1)
- impurities (1)
- microstructure analysis (1)
- multi scale testing (1)
- particle size determination (1)
- pitting corrosion (1)
- sample preparation (1)
- selective laser melting (1)
- thermomechanische Beanspruchung (1)
- utilization, and storage (CCUS) technology (1)
- volume resistivity (1)
- zertifizierte Referenzmaterialien (1)
- Öffentliche Sicherheit (1)
- Überblick (1)
Organisationseinheit der BAM
- 5 Werkstofftechnik (431)
- 5.2 Metallische Hochtemperaturwerkstoffe (115)
- 5.1 Mikrostruktur Design und Degradation (112)
- 5.4 Multimateriale Fertigungsprozesse (101)
- 5.3 Polymere Verbundwerkstoffe (52)
- 5.6 Glas (51)
- 8 Zerstörungsfreie Prüfung (46)
- 5.5 Materialmodellierung (45)
- 9 Komponentensicherheit (44)
- 8.5 Röntgenbildgebung (35)
Eingeladener Vortrag
- nein (431) (entfernen)
Early Material Damage in Equimolar CrMnFeCoNi in Mixed Oxidizing/Sulfiding Hot Gas Atmosphere
(2022)
The challenges to use more varied fuels at medium and high temperatures above 500 °C need to be addressed by tuning the materials towards a better resistance against increased corrosion. As a first step the corrosion processes need to be better understood, especially in the case of the unavoidable and highly corrosive sulfur-based gases. In this work oxidation/sulfidation of an equimolar CrMnFeCoNi high entropy alloy is studied at an early stage after hot gas exposure at 600 °C for 6 h in 0.5% SO2 and 99.5% Ar. The oxidation process is studied by means of x-ray diffraction, scanning and transmission electron microscopy and supported by thermodynamic calculations. It is found that the sulfur does not enter the bulk material but interacts mainly with the fast-diffusing manganese at grain boundary triple junctions at the alloy surface. Sub-micrometer scaled Cr-S-O rich phases close to the grain boundaries complete the sulfur-based phase formation. The grains are covered in different Fe, Mn and Cr based spinels and other oxides.
A new patented dynamic mechanical analysis (DMA) is presented, where the tensile, bending- or torsional stiffness of a media can be characterized in-situ during the phase transition from liquid to solid. An epoxy system, e.g. Hexion L285/H287, is filled into an elastomer container, such as a silicone tube. This can be mounted into a conventional DMA and, based on a linear viscoelastic approach, the storage modulus (E’;G’), the loss modulus (E’’;G’’) and the loss angle tan(delta) can be measured at constant temperature as a function of time in order to investigate the liquid to sol-gel to solid transition. With this new method, the stiffness increase as a result of the cure process can be directly measured more precisely than with a rheometer in a shear plate set-up, because using an elastomer container gives a defined cross section for calculating the Young’s modulus.
Tempered martensite-ferritic steels, such as the grade P92 steel studied in this contribution, exhibit pronounced macroscopic cyclic softening under isothermal low-cycle fatigue (LCF) and non-isothermal thermomechanical fatigue (TMF) conditions, which is considered to be the predominant degradation mechanism in high-temperature fatigue in this and other material groups. However, such softening processes are highly complex since microscopic (e.g., recovery) and macroscopic (e.g., crack initiation and growth), as well as global and local effects superimpose, especially under creep-fatigue conditions. In this contribution, we discuss the cyclic deformation and softening behavior of P92 in strain-controlled LCF, in-phase (IP) TMF, and out-of-phase (OP) TMF tests with and without dwell times in the temperature range from 300 °C to 620°C. EBSD-based dislocation analysis on various fatigued material states confirms the continuous redistribution and annihilation of geometrically necessary dislocations in all studied states, which can be quantitatively correlated with macroscopic softening despite different damage mechanisms for different test types. Deviations from this correlation are observed for OP TMF and LCF with dwell times, i.e., for conditions where optical microscopy reveals pronounced crack-oxidation interactions at the specimen surfaces.
In this work, the focus was set on the corrosion process of condensate as drops on the surface of carbon steels (X52, X70), martensitic steel UNS S41500, and superaustenite UNS 08031 in CO2 atmosphere with impurities at 278 K (to simulate the transportation condition in a buried pipeline). Exposure tests were performed at both normal pressure and high pressure where CO2 is supercritical or in dense phase. The drop, 1 ‑ 10 µL in volume, was prepared by dropping CO2 saturated ultra-pure water onto the surface of steel coupons in a one-liter-autoclave. The CO2 gas stream, simulating the oxyfuel flue gas with varying concentration of impurities (SO2 and O2), was then pumped into the autoclave to observe the condensation and corrosion impacts of impurities. Comparable exposure tests were carried out with the same gas mixture and the same volume of water as vapor to observe the drop formation and the corrosion process that follows. The wettability and stability of drops on the surface of steel coupons in CO2 supercritical/dense phase environment was evaluated additionally by contact angle measurement.
In this work, the focus was set on the corrosion process of condensate as drops on the surface of carbon steels (X52, X70), martensitic steel UNS S41500, and superaustenite UNS 08031 in CO2 atmosphere with impurities at 278 K (to simulate the transportation condition in a buried pipeline). Exposure tests were performed at both normal pressure and high pressure where CO2 is supercritical or in dense phase. The drop, 1 ‑ 10 µL in volume, was prepared by dropping CO2 saturated ultra-pure water onto the surface of steel coupons in a one-liter-autoclave. The CO2 gas stream, simulating the oxyfuel flue gas with varying concentration of impurities (SO2 and O2), was then pumped into the autoclave to observe the condensation and corrosion impacts of impurities. Comparable exposure tests were carried out with the same gas mixture and the same volume of water as vapor to observe the drop formation and the corrosion process that follows. The wettability and stability of drops on the surface of steel coupons in CO2 supercritical/dense phase environment was evaluated additionally by contact angle measurement.
A large amount of publicly available data is reproduced every day in the field of materials science, while these kind of material data can have different formats and types like paper-type publications, standards, datasheets or isolated datasets in repositories. However, gathering a specific library from such extensive and diverse material data is always challenging for the materials scientists and engineers, since the time-related limitations are not allowed to fully access the large publicly available databases; search across these disparate databases, manage the large volumes of heterogeneous datasets, and integrate data from multiple sources. To address these challenges and make data findable, accessible, interoperable, and reusable (FAIR), an efficient data management system is necessary to build comprehensive, documented, and connected data spaces in the future. A formal standardized knowledge representation through an ontology can address such problems and make data more available and interoperable between related domains. Ontology can also rich machine processable semantic descriptions that increases the performance of scientific searches. In this regard, the Platform MaterialDigital (PMD) is currently working on developing a high-level ontology for the materials and material related processes. For example, in one of the PMD projects of “KupferDigital”, we will try to develop a data ecosystem for digital materials research based on ontology-based digital representations of copper and copper alloys. As a case study, this paper describes the methodology for ontology development of Brinell hardness, based on PMD core ontology. The methodology we describe includes the following steps; gathering the required domain terminology from different resources like standards (DIN EN ISO 6506-1) and test reports, representing the performance of a standard-conformant hardness test and the treatment of the recorded values up to a “reportable” hardness value for a material, designing the process chain according to the semantic technologies, and developing a domain-level ontology of Brinell hardness based on PMD ontology semantic formalization. Apart the mentioned methodology, some interesting tools and methods were introduced and ontology design challenges and possible solutions for modelling materials and processes were discussed. Furthermore, a dataset from the Brinell hardness measurement of cast copper samples is prepared for testing the query process.
The employment of renewable energy resources, which are naturally intermittent, for electricity generation has altered the working conditions of conventional power plants from continuous (baseload) to cyclic or flexible operation. For a long time, 9-12% Cr ferritic-martensitic stainless steels have been widely used in power plants due to their favorable characteristics such as high creep strength at high temperatures and oxidation and corrosion resistance. The components of power plants are subjected to long term cyclic loadings including fatigue and creep-fatigue at high temperatures. As ferritic-martensitic steels are known to exhibit cyclic softening when subjected to such loading scenarios, it is crucial to study the material response in such conditions. Since it is impossible to test the material behavior exactly as the operation conditions of power plants, due to technical difficulties and cost issues, it is necessary to develop physically-based material models that can predict the material behavior in more realistic situations.
In recent years, many material models have been proposed to describe the behavior of 9-12% Cr ferritic-martensitic stainless steels, which follow phenomenological or physically-based approaches. Phenomenological models provide a stress-strain relation based on empirical observations although they usually lack physical background. To alleviate this drawback and to allow for more flexibility and wider ranges of strain-rate and temperature, physically-based models are suggested. In this approach, microstructural evolution, dislocation movement and/or kinetics of plastic deformation processes are included. The physically-based models allow for a better extrapolation from the experiment results to other operation conditions and their material constants can be interpreted physically. Compared to the former approach, the material behavior can be described more accurately and flexibly and the number of material constants is less in general. In the presented work, the existing micromechanical models developed for P92 steel are compared and extended to allow for new dislocation-based strengthening/cyclic mechanisms. Their performance is assessed in the light of mechanical test data from creep-fatigue and thermo-mechanical fatigue experiments and detailed characterizations of the microstructure evolution in the fatigued material.
We report about a joint project aiming at the digitalization of a lab course in materials testing. The undergraduate students were asked to prepare samples of a precipitation hardened aluminum alloy and characterize them using hardness and tensile tests. In a first step, we developed the frames for the digital labor notebook using eLabFTW. The primary data and the relevant metadata of each run were saved in a central database and made available for analysis and report issues. The whole set of results produced in a course was made available in the database. This database can be improved and serve as an open repository for data on this specific alloy.
The logical frame for the joint project was provided by the PMD Core Ontology (PMDco), a mid-level ontology that enables the representation and description of processes and process chains in an MSE-specific manner, ensuring full traceability of generated data. For the digitalization of this lab course, the tensile test ontology (TTO) was applied which is designed as a module of the PMDco using strongly related semantic concepts.
Zur Bewältigung der Herausforderung bei der Digitalisierung von Materialien und Prozessen ist eine mit allen Stakeholdern konsistente Kontextualisierung von Materialdaten anzustreben, d.h. alle erforderlichen Informationen über den Zustand des Materials einschließlich produktions- und anwendungsbezogener Änderungen müssen über eine einheitliche, maschinenlesbare Beschreibung verfügbar gemacht werden. Dazu werden Wissensrepräsentationen und Konzeptualisierungen ermöglichende Ontologien verwendet. Erste Bemühungen in den beiden Projekten Plattform Material Digital und Materials-open-Laboratory führten zur Erstellung von Anwendungsontologien, die Prozesse und Testmethoden explizit beschreiben. Dabei wurde u.a. der Zugversuch an Metallen bei Raumtemperatur nach DIN EN ISO 6892-1 ontologisch beschrieben. Diese als Beispiel dienende Ontologieentwicklung wird in dieser Präsentation vorgestellt.
This study aims to represent an approach for transferring the materials testing datasets to the digital schema that meets the prerequisites of the semantic web. As a use case, the tensile stress relaxation testing method was evaluated and the testing datasets for several copper alloys were prepared. The tensile stress relaxation testing ontology (TSRTO) was modeled following the test standard requirements and by utilizing the appropriate upper-level ontologies. Eventually, mapping the testing datasets into the knowledge graph and converting the data-mapped graphs to the machine-readable Resource Description Framework (RDF) schema led to the preparation of the digital version of testing data which can be efficiently queried on the web.
In this presentation, the results of the determination of the diffraction and single-crystal elastic constants of laser powder bed fused Inconel 718 are presented. The analysis is based on high-energy synchrotron diffraction experiments performed at the Deutsches Elektronen-Synchrotron. It is shown that the characteristic microstructure of laser powder bed fused Inconel 718 impacts the elastic anisotropy and therefore the diffraction and single-crystal elastic constants. Finally, the consequences on the diffraction-based residual stress determination of laser powder bed fused Inconel 718 are discussed.
Laser powder bed fusion (PBF-LB/M) of metallic alloys is a layer-wise additive manufacturing process that provides significant scope for more efficient designs of components, benefiting performance and weight, leading to efficiency improvements for various sectors of industry. However, to benefit from these design freedoms, knowledge of the high produced induced residual stress and mechanical property anisotropy associated with the unique microstructures is critical. X-ray and neutron diffraction are considered the benchmark for non-destructive characterization of surface and bulk internal residual stress. The latter, characterized by the high penetration power in most engineering alloys, allows for the use of a diffraction angle close to 90° enabling a near cubic sampling volume to be specified. However, the complex microstructures of columnar growth with inherent crystallographic texture typically produced during PBF-LB/M of metallics present significant challenges to the assumptions typically required for time efficient determination of residual stress. These challenges include the selection of an appropriate set of diffraction elastic constants and a representative lattice plane suitable for residual stress analysis. In this contribution, the selection of a suitable lattice plane family for residual stress analysis is explored. Furthermore, the determination of an appropriate set of diffraction and single-crystal elastic constants depending on the underlying microstructure is addressed.
In-situ loading experiments have been performed at the Swiss Spallation Neutron Source with the main scope to study the deformation behaviour of laser powder bed fused Inconel 718. Cylindrical tensile bars have been subjected to an increasing mechanical load. At pre-defined steps, neutron diffraction data has been collected. After reaching the yield limit, unloads have been performed to study the accumulation of intergranular strain among various lattice plane families.
Thermal spraying provides a rapid method for additive deposition of various ceramics as electrical insulation in applications where polymers are not suitable. New applications in complex shaped additive manufactured metal parts are emerging for example in large scale electrical devices. Microstructural and dielectric evaluation of coatings is crucial to the employment of such free-form processes. The properties and microstructure of the plasma sprayed alumina coatings are compared with dense reference samples of the same powder produced by spark plasma sintering (SPS). To obtain dense bulk samples from the coarse alumina powder for spray coating, SPS is used.
Samples are fabricated by atmospheric plasma spraying (APS) of commercially available alumina powder (d50 = 33 µm) on copper substrates and by SPS of the same powder. Microstructure and porosity were analyzed by optical microscopy and scanning electron microscopy (SEM). Phase compositions were determined by X-ray diffraction (XRD). Dielectric properties such as DC resistance, dielectric strength, dielectric loss, and relative permittivity were determined according to the standards. The microstructure and dielectric properties of the coating and bulk material are compared to assess whether the coating is suitable for use in electrical insulation application.
Die Fraktographische Online-Datenbank der AG Fraktographie – Entwicklungsstand und weitere Planung
(2023)
Vortrag zum aktuellen Stand der fraktographischen online-Datenbank. Darstellung des AGM/DVM Gemeinschaftsausschusses REM in der Materialforschung und seiner Arbeitsgruppen Fraktographie, EBSD und 2D/3D-Prüfung. Ziele und Inhalte der fraktographischen Datenbank, Aufruf zum Mitmachen. Durchführung von Vergleichsversuchen, Entwicklung einer fraktographischen Symbolik, Ringversuch, Vorhaben iFrakto mit Entwicklung einer KI-gestützten Bruchflächenanalyse.
Die Bereitstellung von zuverlässigen Werkstoffdaten stand für die Werkstoffprüfung seit dem 19. Jahrhundert in zentraler Stelle. Mit der zunehmender Digitalisierung unserer Gesellschaft gewinnt das Datenmanagement insbesondere im Hinblick auf die Modellierungs- und Simulationsaktivitäten an Bedeutung.
In unserem Beitrag beschreiben wir die gegenwärtigen Aktivitäten in Deutschland – insbesondere die NFDI-MatWerk und die BMBF-Initiative MaterialDigital – sowie in Europa und Übersee. Abschließend heben wir die Auswirkungen auf die technische und akademische Aus- und Weiterbildung.
Thermoelectric generators can be used as energy harvesters for sensor applications. Multilayer thermoelectric generators (ML-TEGs) are a promising alternative to conventional π-type generators due to their high filling factor, high capability of automated production and the texturing potential during the production process. Calcium cobaltite is a promising thermoelectric oxide (p-type) with highly anisotropic properties. The following study shows the development of a textured unileg ML-TEG using ceramic multilayer technology.
Tape-casting and pressure assisted sintering are applied to fabricate textured calcium cobaltite. Compared to conventional sintering, pressure assisted sintering increases the strength by the factor 10. Thermoelectric properties can be tuned either towards maximum power factor or towards maximum figure of merit depending on the pressure level.
As electrical insulation material, a screen-printable glass-ceramic with high resistivity and adapted coefficient of thermal expansion is developed. From various commercial pastes a metallization with low contact resistance is chosen. The unileg ML-TEG is co-fired in one single step. The demonstrators reach 80% of the simulated output power and the power output is highly reproducible between the different demonstrators (99%). These results provide the first proof-of-concept for fabricating co-fired multilayer generators based on textured calcium cobaltite with high power factor, high density, and high strength.
At high temperatures and in harsh environments ceramic springs are often superior to metallic ones and allow for innovative solutions. A further application was proposed by using ceramic springs as capacitive force sensor. Lower and upper coil surfaces are coated by electrically conducting layers. Deformation of such spring results in a change of capacity. Sensor application calls for helical springs with rectangular cross-section, a linear stress-strain characteristic over entire deformation range and low manufacturing tolerances relating to inner and outer diameter, coil cross section and spring pitch. Furthermore, complex spring design with integrated connecting elements has to be realized.
Alumina, zirconia (Y-TZP) and silicon nitride springs were produced by hard machining starting from sintered hollow cylinders. After external and internal cylindrical grinding the hollow cylinders were filled with hard wax, followed by multi-stage cutting of spring coils with custom-made cutting discs. Finally, hard wax was removed by melting and burnout. Best surface and edge qualities of springs were reached using Y-TZP material and hot isostatic pressed alumina. Y-TZP springs produced with material-specifically selected cutting discs and optimized process parameters show sharp coil edges without spallings and mean roughness values of inner surfaces < 0.2 μm. Manufacturing tolerances of spring diameters, spring pitch, height and width of coil cross section are in the range of ± 10 microns. Good reproducibility of spring geometry by optimized hard machining technology allows for production of Y-TZP springs with spring constants differing less than ± 1 % within a series.
According to DIN 2090 spring constant for rectangular coil cross section is proportional to the square of height and width of coil cross section and indirectly proportional to number of active coils and to the cube of the mean spring diameter. Hence, spring constants can be tailored over a range of many orders of magnitude by changing the spring dimensions. Good agreement was reached between calculated target spring constants and measured values on produced springs.
Alumina and zirconia springs were characterized relating to deformation behavior under dynamic compression load with various deformation speeds and under static tensile loads over long periods of time. Contrary to alumina springs, a non-linear stress-strain behavior of TZP springs was proved in both test series. It is supposed, that pseudoelasticity caused by stress-induced transformation of tetragonal to monoclinic phase is responsible for this special feature of TZP springs. Therefore, TZP material cannot be used for capacitive spring sensors.
Efforts towards digitalization in the material science and technology community have enhanced in the last years. In 2019 the German digitalization initiative platform „MaterialDigital“1 (MD) has been started. Numerous projects concerning digitalization, including the copper related project „KupferDigital“ (copper digital) have been initiated under the umbrella of MD. The initiative strives to
address numerous issues concerning data access, exchange, security, provenance and sovereignty. Heterogeneous data origin, storage and evaluation often result in problems concerning comparability and reproducibility of scientific and technological results. In many cases material data are recorded, but the methods of testing are insufficiently described, or such information is not communicated along with the raw data. The material data can also have numerous different formats such as paper printouts, pdfs, excel sheets or csv-files. Hence, gathering and integrating material data from different sources is challenging for potential users like materials scientists and engineers, especially if there are contradictory data where the reasons for contradictions is not clear due their vague description. In order to address these problems, data should comply to the so called „FAIR“ principle which calls for data to be findable, accessible, interoperable, and reusable (FAIR)2 and hence be accessible via so-called decentralized but interconnected data spaces. By using knowledge representation withontologies, data can be enriched with meaning and the methods of the testing procedures can be accurately provided. In this presentation we want to introduce our approach to such knowledge representation based on a high-throughput alloy development process for Cu-based alloys³ along with characterization techniques such as hardness testing and microstructural characterization (e.g. EBSD – Electron Backscattered Diffraction).
Many microstructural features exhibit non-trivial geometries, which can only be derived to a limited extent from two-dimensional images. E.g., graphite arrangements in lamellar gray cast iron have complex geometries, and the same is true for additively manufactured materials and three-dimensional conductive path structures. Some can be visualized using tomographic methods, but some cannot be due to weak contrast and/or lack of resolution when analyzing macroscopic objects. Classic metallography can help but must be expanded to the third dimension. The method of reconstructing three-dimensional structures from serial metallographic sections surely is not new. However, the effort required to manually assemble many individual sections into image stacks is very high and stands in the way of frequent application. For this reason, an automated, robot-supported 3D metallography system is being developed at BAM, which carries out the steps of repeated preparation and image acquisition on polished specimen.
Preparation includes grinding, polishing and optionally etching of the polished surface. Image acquisition comprises autofocused light microscopic imaging at several magnification levels. The image stacks obtained are then pre-processed, segmented, and converted into 3D models, which in the result appear like microtomographic models, but with high resolution at large volume. Contrasting by classical chemical etching reveals structures that cannot be resolved using tomographic methods. The integration of further imaging and measuring methods into this system is underway. Some examples will be discussed in the presentation.
Determination of Distribution Function used in MCS on Safety Analysis of Hydrogen Pressure Vessel
(2019)
The test data of static burst strength and load cycle strength of composite pressure vessels are often described by GAUSSian normal or WEIBULL distribution function to perform safety analyses. The goodness of assumed distribution function plays a significant role in the inferential statistics to predict the population properties by using limited test data. Often, GAUSSian and WEIBULL probability nets are empirical methods used to validate the distribution function; Anderson-Darling and KolmogorovSmirnov tests are the mostly favorable approaches for Goodness of Fit. However, the different approaches used to determine the parameters of distribution function lead mostly to different conclusions for safety assessments. In this study, six different methods are investigated to show the variations on the rates for accepting the composite pressure vessels according to GTR No. 13 life test procedure. The six methods are: a) NormLog based method, b) Least squares regression, c) Weighted least squares regression, d) A linear approach based on good linear unbiased estimators, e) Maximum likelihood estimation and f) The method of moments estimation. In addition, various approaches of ranking function are considered. In the study, Monte Carlo simulations are conducted to generate basic populations based on the distribution functions which are determined using different methods. Then the samples are extracted randomly from a population and evaluated to obtain acceptance rate. Here, the “populations” and “samples” are corresponding to the burst strength or load cycle strength of the pressure vessels made from composite material and a plastic liner (type 4) for the storage of hydrogen. To the end, the results are discussed, and the best reliable methods are proposed.
The presence of large quantities of plastic waste and its fragmentation in various environmental compartments are an important subject of current research. In the environment, (photo ) oxidation processes and mechanical abrasion lead to the formation of microplastics. However, until now, there are no established quality assurance concepts for the analysis of microplastic (<5 mm) in environmental compartments, including sampling, processing and analysis.
The aim of the present work is the development of suitable examination methods and protocols (sampling, sample preparation and detection) to qualify and quantify microplastic in urbane water management systems. At first a fractional filtration system for sampling and the analytical tool, the so-called TED-GC-MS (thermal desorption gas chromatography mass spectrometry) were developed. The TED-GC-MS method is a two-step analytical procedure which consists of a thermal extraction where the sample is annealed and characteristic decomposition products of the polymers are collected on a solid phase. Afterwards these products are analysed using GC-MS. The developed fractional filtration for sampling and the TED-GC-MS for detection were used for quantitative analysis to screen the waste water influent and effluent of a Berlin waste water treatment plant for the most relevant polymers, polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET) and polyamide (PA).
The results of the study revealed that the polymeres PE, PS and PP were detected in the effluent, and PE and PS were find in the raw waste water of the sewage treatment plant in Ruhleben, Berlin. Differences in polymer types and amounts were detected at different sampling dates and within different sieve fractions. Much higher amounts of polymers were observed in the raw waste water. The peak areas of the decomposition products, used for quantification of the polymers, were adjusted using so-called response factors since the TED-GC-MS method is more sensitive for PP and PS than for PE. It has been shown that PE is the most dominant polymer in the samples. Comparing the masses of polymers in the effluent and in the raw sewage, a removal of 99 % of the polymers in the water treatment plant can be assumed. These results are consistent with the literature where removal rates between 98-99 % were described.
Destructive and non-destructive 3D-characterization of inner metal structures in ceramic packages
(2023)
Ceramic multilayer packages provide successful solutions for manifold
applications in telecommunication, microsystem, and sensor technology. In such packages, three-dimensional circuitry is generated by combination of structured and metallized ceramic layers by means of tape casting and multilayer technology. During development and for quality assurance in manufacturing, characterization of integrity, deformation, and positioning of the inner metal features is necessary.
Visualization with high resolution and material contrast is needed.
Robot-assisted 3D-materialography is a useful technique to characterize such multimaterial structures. In that, many sections of the specimen are polished and imaged automatically. A three-dimensional representation of the structure is created by digital combination of the image stack. A quasi non-destructive approach is to perform X-ray computer tomography (CT) with different beam energies. The energies are chosen to achieve a good imaging of either the metal features, or the ceramic matrix of the structure. The combination of the respective tomograms results in a high contrast representation of the entire structure. Both methods were tested to characterize Ag and Ag/Pd conductors in a ceramic multilayer package. The results were compared in terms of information content, effort, and applicability of the methods.
Ceramic springs offer versatile possibilities for load bearing or sensor applications in challenging environments. Although it may appear unexpected, a wide range of spring constants can be implemented by material selection and especially by the design of the spring. Based on a rectangular cross-section of the windings, it is possible to design a spring geometry that generates the desired spring constant simply by choosing appropriate diameter, height, widths, and number of windings. In a recent research project the calculation of helical compression springs made of rectangular steel (German standard DIN 2090) was applied for the design of ceramic springs. A manufacturing technology has been worked out to fabricate such springs from hollow cylinders of several highly dense technical ceramics by milling. Ceramic springs with precise rectangular section, without edge damage, and mean surface roughness smaller than 0.2 µm were produced after parameter optimization. Tolerances of less than 10 µm were achieved regarding spring diameter, height, and width of cross section. It is shown that the calculations outlined in the standard are valid for a variety of ceramic materials as well. Demonstrator springs with a wide range of spring constants have been fabricated, including zirconia springs with 0.02 N/mm, alumina springs with 1 N/mm and Si3N4 springs with 5 N/mm. A reproducibility study of six zirconia springs with a constant of 0.3 N/mm showed a relative difference in spring constants of less than +/- 1 %. This combination of a valid calculation approach for spring geometry and a reliable manufacturing technology allows for purposeful development and fabrication of ceramic springs with precise mechanical properties and superior chemical stability.
Systematic microstructure design requires reliable thermodynamic descriptions and phase diagrams of each and all microstructure elements. While such descriptions are well established for most bulk phases, thermodynamic assessment of crystal defects is greatly challenged by their individualistic aspects. In this talk, we present a density-based thermodynamic concept to describe defects based on available bulk thermodynamic data. Here dealing with grain boundaries (GBs), we apply this concept to compute GB (phase) diagram. Applications to segregation engineering of GBs in bulk and nanocrystalline alloys will be presented. We further develop this model to include the effect of elastic interactions due to atom size mismatch and obtain the corresponding GB (phase) diagram for the ternary Al-Cu-Li system.
Grain boundary (GB) chemical and structural variations can significantly influence materials performance. The former is generally ascribed to the structural gradient between the grain and GB. While GB segregation may be accompanied by chemical and structural variations, clear insights about the GB’s thermodynamic phase behaviour upon coupling between its chemistry and structure is lacking. Using the CALPHAD integrated density-based phase field model, we study the co-evolution of GB’s structure and segregation in Fe-Mn alloys. We found that the GB segregation transition is amplified if its structure can respond to chemical variation. Additionally, the coupling between GB structural and segregation evolution was found to enable co-existence of the spinodally formed low- and high-Mn phases within the GB. In the light of atomistic simulations, we expand on investigating the correlation between the parameters that characterise the GB density map with GB properties.
Regarding feedstocks for the additive manufacturing (AM) of ceramics, two features are most critical in classical powder based AM processes: a high particle packing density (typically >50% TD) must be achieved with very fine particles (typically submicron) in order to ensure sufficient sintering activity. Three innovative approaches will be introduced to overcome this problem:
1. Layer wise slurry deposition: The use of water based ceramic slurries as feedstock for the additive manufacture of ceramics has many advantages which are not fully exploit yet. In the layerwise slurry deposition (LSD) process a slurry with no or low organic content is repetitively spread as thin layers on each other by means of a doctor blade. During the deposition, the ceramic particles settle on the previously deposited and dried material to form thin layers with a high packing density (55-60%). The LSD therefore shares aspects both of tape casting and slip casting. The LSD differentiates from the classical powder-based AM layer deposition, which typically achieves with a flowable coarse grained powder a low packing density (35-50%) only, consequently hindering the ability of sintering ceramic parts to full density. The LSD is coupled with the principles of selective laser sintering (SLS) or binder jetting, to generate novel processes which take advantage of the possibility of achieving a highly dense powder-bed.
2. Laser induced slip casting: Contrary to the LSD process, which requires drying of each individual layer, the direct interaction of ceramic slurries with intense laser radiation, for the laser induced slip casting (LIS), is a promising approach for the additive manufacture of voluminous parts.
3. Gas flow assisted powder deposition: By the application of a vacuum pump a gas flow is realized throughout the powder bed. This gas flow stabilizes the powder bed and results into an enhanced flowability and packing density of the powder during layer deposition.
The presentation will provide a detailed discussion of potentialities and issues connected to the mentioned technologies and will describe the most recent developments in their application to technical ceramics.
Many of the most successful and precise additive manufacturing (AM) technologies are based on the deposition layer-by-layer of a flowable powder. Since the first pioneering work at the end of the 1980th many developments have been introduced, greatly extending the use of different materials, improving the physical properties of the components built and enhancing the accuracy of the process. Still very important issues remain nowadays, hampering a completely autonomous production of parts and even restricting the freedom of design by means of these technologies. One of the major issues is the low density and stability of the parts during the building process, which implies the need of support structures: The powder bed surrounding the part has an essential role, since it should support the structure during building, until it’s ready for removal. Moreover, the microstructure of the powder bed is a template for the microstructure of the part produced. In this context, the use of submicron ceramic powders is still a challenge. Three approaches for the stabilization and densification of powder beds will be presented: The Layerwise Slurry Deposition process LSD, the gas flow assisted powder deposition and the Laser Induced Slipcasting (LIS) of ceramic powder compacts.
In our current view, reference datasets in the MSE domain represent specific material properties, e.g., structural, mechanical, … characteristics. A reference dataset must fulfill high-quality standards, not only in precision of measurement but also in a comprehensive documentation of material, processing, and testing history (metadata). This Infrastructure Use Case (IUC) aims to develop a framework for generating reference material datasets using creep data of a single crystal Ni-based superalloy as a best practice example. In a community-driven process, we aim to encourage the discussion and establish a framework for the creation and distribution of reference material datasets. In this poster presentation, we highlight our current vision and activities and intend to stimulate the discussion about the topic reference datasets and future collaborations and work.
At high temperatures and in harsh environments ceramic springs are often superior to metallic springs and allow for innovative solutions. A recently proposed application involves ceramic springs with metallized surfaces as capacitive force sensor. A strictly linear stress-strain characteristic of the spring is a precondition for such a sensor.
Helical ceramic springs with rectangular cross-section have been produced from sintered hollow cylinders. Alumina, ATZ, Y-TZP, and Ce-TZP springs with identical dimensions were characterized and compared regarding deformation behavior.
Spring deformation was investigated under various load scenarios.
Dynamic compression was performed with deformation speeds from 0.3 to 30 mm/min. Spring constants of alumina springs are strain rate independent. By contrast, Y-TZP spring constant increases by approximately 3 % within the experimental framework.
A high-precision test facility was developed to characterize spring displacement in nm range under static tensile load over long periods of time. Spring elongation with asymptotic course was observed for zirconia containing materials at room temperature. This effect is particularly strong in the case of Y-TZP. Up to 0.3 % time-dependent elongation was measured after 24 h under constant load. Deformation is completely reversible after unloading. Alumina springs do not show any time-dependent deformation under identical test conditions.
Contrary to alumina springs, a non-linear stress-strain behavior of TZP springs at room temperature was proved in both test series. It is supposed, that pseudo-elasticity caused by stress-induced phase transformation from tetragonal to monoclinic is responsible for this special behavior of TZP springs.
The Topic of the presentationis a discussion on defects which can cause failure in cyclically loaded metallic components. Although also touching Features such as material defects such as pores or micro-shrinkages, etc. and geometric defects such as surface roughness and secondary notches (which are not considered in the design process) which origin in manufacturing, and others the presentation concentrates on non-metallic inclusions. It is prefaced by an introduction to the life cycle of a fatigue crack from initiation up to fracture. Special emphasis is put on the fact that only cracks which are not arrested during one of their distinct Propagation stages can grow to a critical size.
Damage tolerance counts as one of the most widespread approach to fatigue assessment and surely as one of the most promising in understanding the process-structure-property-performance relationships in additively manufactured metallic materials. Manufacturing defects, surface roughness, microstructural features, short and long crack fatigue propagation, residual stresses and applied loads can be taken into consideration in a fracture mechanics-based fatigue assessment. Many aspects are crucial to the reliable component life prediction. Among those a prominent role is played by an accurate measurement and modelling of the short crack fatigue behavior, and reliable statistical characterization of defects and residual stresses.
This work aims at addressing the issues related to both experimental testing, fatigue and fatigue crack propagation, and fracture mechanics-based modelling of fatigue lives. Examples will be provided on an additively manufactured AISI 316 L.
Currently, the Full Notch Creep Test (FNCT) [1] method is used by material suppliers and end users in industry for the approval of container and pipe materials based on high-density polyethylene (PE-HD). The resistance to environmental stress cracking (ESC) of the material is evaluated using the time to failure of the specimen in an aqueous solution of a detergent [2, 3]. Usually specimens made of sheets with isotropic material properties, manufactured by hot pressing, are employed in order to obtain intrinsic properties of the material in terms of ESC failure. In contrast, the processes used in manufacturing to form containers and pipes, such as extrusion blow molding or extrusion, impose anisotropic properties to the material. These are mostly due to a microstructural orientation (polymer chains or crystallites) [4]. Furthermore, the different cooling conditions significantly affect the size distribution of crystallites as well as the overall morphology. It is therefore essential to understand the influence of process-induced material characteristics on failure due to ESC.
A large number of studies on material properties as a function of microstructural preferential orientation have already been conducted [5-7]. However, effects on ESC as the major failure mechanism of containers and pipes are still rather unexplored [8, 9]. The most important factor is whether primarily intramolecular high-strength covalent bonds or the substantially weaker intermolecular van der Waals forces are predominantly loaded.
In addition to the widely established classification by time to failure, the strain or crack opening displacement (COD) provides valuable information about the evolution and progression of damage as a function of time [10, 11]. Optical strain measurement using digital image correlation allows the differences in COD for isotropic and different angles of orientation of anisotropic specimens to be discussed. Also, a post-fracture surface analysis provides clarification on the craze-crack mechanism of the ESC. These different ESC-related properties of extruded and hot-pressed specimens have been investigated at different environmental medium temperatures and different initial stresses to provide a broad characterization of the fracture behavior of PE-HD.
Wind turbine rotor blades, made of fiber reinforced polymers (FRP), often fail before their projected 20-year lifespan, largely due to defects that originate during manufacturing and are propagated by operational fatigue and environmental conditions. The cost-intensive replacement outcomes lead to a high loss of earnings, and are one of the inhibitors of wind turbine production [1]. A potential repair alternative is to locally patch these areas of the blades with adhesively bonded structural repairs. However, the effects of such repair methods of the outer shell region on the structural integrity of the rotor blades are still largely unknown, and are thus investigated in this project.
The shell components of rotor blades are made of FRP composite material sandwiching a lightweight core, often a rigid foam or Balsa wood. The repair methods involve replacing the lost load path with a new material that is joined to the parent structure [2]. Repairs in this project focus on the scarf method, which allow for a smoother load distribution across the joint, aiming to study the damage mechanism of glass FRP scarf repairs for wind turbine blade shell applications. Namely, the source and path of the damage initiation and propagation, role of the interface between parent and patch material, and the role of the fiber orientation mismatch at this interface are examined. Biaxial ±45° and 0/90° FRP specimens are produced with the vacuum-assisted resin infusion (VARI) process using E-glass non-crimp fabric. The patch layers are then joined using VARI with a scarf ratio of 1:50, using glass FRP fabric with half the areal weight of the parent side to allow for better drapability. The methods and practices in specimen production are based on common industry practice in rotor blade shell manufacturing and repairs.
The specimens are tested under uniaxial tensile load, during which they are periodically monitored for damage onset. A comparison of the ±45° and 0/90° specimens allows for an understanding of the role of a highly mismatching fiber orientation in the transition zone between parent and patch material on the failure mechanism of the scarf joint. Although failure in both orientations begins as delamination at the joint edge, the difference in the mechanisms at play in the two different specimen types leads ultimately to different fracture paths. Namely, in the inter fiber failure mechanism of the ±45° specimens, the higher interlaminar strength compared to the intralaminar strength of the laminate leads to intralaminar failure of the ±45° scarf joint specimens. Alternatively, the competition in the 0/90° specimens lies between the interlaminar strength and fiber failure strength, and here we experience failure primarily across the scarf joint length. The scarf joint in the 0/90° specimens disrupts the continuity of the load-carrying 0° layers, directing the failure path to remain primarily along the scarf joint. Experimental results are compared to finite element analyses of scarf patch repairs on glass FRP sandwich specimens with the same respective layup orientations, where the damage initiation regions are identified and correlated to fiber orientation, serving as a bridge to future work which will experimentally examine the scarf repair patches on sandwich shell specimens.
The current trend towards cyclic, “flexible” operation of fossil-fueled power plants constitutes a major issue regarding lifetime and operational safety of the respective installations and their components, as was outlined in our complementary contribution (Part 1). The present contribution reports on the investigation of the microstructure evolution in cyclically loaded ferritic-martensitic steels and its representation in a physically-based micromechanical model.
For this purpose, specimens of P92 steel grade from the mechanical test programme outlined in our companion contribution (Part 1) were analyzed by scanning electron microscopy (SEM), including backscattered diffraction (EBSD) mapping, and transmission electron microscopy (TEM). A novel method was implemented to improve angular resolution of EBSD scans. Additionally, a correlative microscopy approach was developed and used to correlate EBSD and TEM measurements on the same locations of thick regions of electron transparent specimens. By applying these techniques, a detailed quantitative microstructure description of the as-received material condition, namely in terms of subgrain morphology and dislocation density/distributions, was established. Comparisons of as-received and cyclically loaded conditions from tests interrupted at different stages of lifetime indicate a rapid redistribution of in-grain dislocations with a strong interaction between mobile dislocations and low angle grain boundaries (LABs).
The proposed micromechanical model is formulated in a viscoplastic self-consistent (VPSC) scheme, which is a mean-field approach that allows us to include the crystal details at the level of slip systems while avoiding the considerable computational costs of full-field approaches (such as the classical crystal plasticity finite element analysis). Being physically-based, the model uses dislocation densities and includes the interaction between dislocations, e.g. annihilation of mobile dislocations, and evolution of microstructure, e.g. the grain coarsening. Particularly, the constitutive laws for dislocation evolution and interaction between dislocations and low angle boundaries are calibrated based on two-dimensional discrete dislocation dynamic (2D DDD) simulations, which are performed at a micro-/meso-scale. The results of the beforementioned EBSD experiments are considered as a direct input, involving e.g. the amount of geometrically necessary dislocations, average misorientations and grain characteristics.
9-12% Cr ferritic-martensitic stainless steels are widely used as high temperature construction materials in fossil fueled power plants due to their excellent creep and oxidation resistance, but changes in electricity markets during the last two decades have considerably changed the typical working conditions of these facilities. The growing share of renewable energy sources in power generation forces most of these plants into flexible operation with frequent load shifts or shutdowns. These cyclic operation profiles constitute a major lifetime issue, raising the question which fundamental processes govern the reaction of ferritic-martensitic steels to cyclic load and temperature variations.
The present contribution reports on current findings obtained in a multidisciplinary project funded by German Ministry of Education and Research (BMBF) which combines cyclic mechanical and cyclic oxidation testing of different 9-12% Cr grades with detailed microstructural analyses and related micromechanical modeling.
In the present first part of our contribution, an overview will be given on the results obtained in the mechanical testing programme of the project. Mechanical analyses were carried out on P91 and (mainly) P92 steel grades, particularly looking at softening phenomena and lifetimes obtained in isothermal cyclic loading (low cycle fatigue, LCF), non-isothermal cyclic loading (thermo-mechanical fatigue, TMF), and service-like combinations of creep and fatigue periods. For this purpose, cylindrical specimens were extracted from thick-walled steam pipes, orthogonal to the pipe axis, and subjected to strain controlled cyclic loading (± 0.2 to ±0.5 % mechanical strain) to different degrees of softening at temperatures up to 620 °C.
The test results will be presented and discussed with a focus on the impact of hold periods (i.e. combined creep-fatigue conditions) on mechanical softening, lifetime and crack formation. Details on the microstructural evolution and their representation in a micromechanical model will be given in a second, complementary contribution to this conference.
Cyclic mechanical performance and microstructure evolution of P92 under LCF and TMF conditions
(2019)
9-12% Cr ferritic-martensitic stainless steels are widely used as high temperature construction materials in fossil fueled power plants due to their excellent creep and oxidation resistance, but changes in electricity markets during the last two decades have considerably changed the typical working conditions of these facilities. The growing contribution of renewable energy sources in power generation forces most of these plants into flexible operation with frequent load shifts or shutdowns. These cyclic operation profiles constitute a major lifetime issue, raising the question which fundamental processes govern the reaction of ferritic-martensitic steels to cyclic load and temperature variations.
The present contribution reports on current findings obtained in a multidisciplinary project funded by German Ministry of Education and Research (BMBF) which combines cyclic mechanical and cyclic oxidation testing of different 9-12% Cr grades with detailed microstructural analyses and related micromechanical modeling.
In this contribution, an overview will be given on the results obtained in the mechanical testing programme of the project. Mechanical analyses were carried out on P91 and (mainly) P92 steel grades, particularly looking at softening phenomena and lifetimes obtained in isothermal cyclic loading (low cycle fatigue, LCF), non-isothermal cyclic loading (thermo-mechanical fatigue, TMF), and service-like combinations of fatigue and creep/relaxation periods. For this purpose, cylindrical specimens were extracted from thick-walled steam pipes, orthogonal to the pipe axis, and subjected to strain controlled cyclic loading (± 0.2 to ±0.5 % mechanical strain). Temperature intervals of TMF tests were chosen as either 300-620°C or 500-620°C, resembling so-called warm or hot start conditions of a power plant.
The test results will be presented and discussed with a focus on the impact of hold periods during testing (combined creep/relaxation-fatigue conditions) on mechanical softening, lifetime and formation of cracks. The findings will be complemented by results on the modification of the hierarchical ferritic-martensitic microstructure under different loading scenarios.
9-12% Cr ferritic-martensitic stainless steels are widely used as high temperature construction materials in power plants due to their excellent creep and oxidation resistance. The growing share of renewable energy sources in power generation forces many of these plants into more flexible operation with frequent load shifts or shutdowns. These cyclic operation profiles constitute a major lifetime issue. The present contribution reports on current findings obtained in a multidisciplinary project which combines cyclic mechanical and cyclic oxidation testing of different 9-12% Cr grades with detailed microstructural analyses.
Mechanical analyses are carried out on P92 and P91 steel grades to give an overview of softening phenomena and lifetimes obtained in isothermal cyclic loading (low cycle fatigue, LCF), non-isothermal cyclic loading (thermo-mechanical fatigue, TMF), and service-like combinations of creep and fatigue periods.
Complementary microstructural investigations by scanning and transmission electron microscopy plus EBSD are used for phase identification, substrate/oxide interface characterization and quantification of the microstructure evolution under cyclic conditions.
Cyclic fatigue behavior of glass fiber reinforced epoxy resin at ambient and elevated temperatures
(2018)
The fatigue behavior of ±45° glass fiber reinforced epoxy resin under cyclic mechanical and constant thermal loading is investigated in this study. Tests at three different temperature levels in the range 296 K to 343 K have been performed in order to create S-N curves for each temperature level. The specimen damage is measured in-situ using optical grayscale analysis. The characteristic damage state (CDS) is evaluated for each specimen. It is shown that the point of CDS is suitable as a failure criterion to compare the resulting S-N curves. With micromechanical formulations, the temperature-dependent matrix effort is calculated for each stress-temperature level. In terms of matrix effort, the longest fatigue life is reached at high temperatures, while, in terms of stress, the lowest fatigue life is reached at the highest temperatures.
This presentation is a summary of the work from the past 20 years’ development of PMC-testing at the BAM-FB 5.3 with respect to safety-relevant design of advanced light weight structures in aircraft, wind turbine and automotive applications. The talk begins with wood as an example from nature, and emphasizes that load case, fiber architectural design and the production process and quality have to go hand in hand to generate an advanced light weight structure. Since PMC-relevant basic findings of mankind span across hundreds of years, high-performance composite applications today are based more on long term experiences than on breakthrough inventions of modern days.
In the second part of the talk, future plans and projects of FB-5.3 are presented, specifically addressing H2-safety, circular economy, recycling by design and digitalization of PMC-technologies.
The development of refractory CCAs has been explored for potential use in high temperature applications. An example of this is the AlMo0.5NbTa0.5TiZr alloy, which resembles the well-known γ/γ’ microstructure in Ni-Base superalloys with cuboidal particles embedded in a continuous matrix. The aim of this work is to evaluate the alloy’s mechanical behavior under tension in the temperature range 800-1000°C, by applying creep tests under vacuum (excluding oxidation effects). Some little temperature influence on minimum creep rate @ 1000 and 1100 °C was found and at a first glance, and Norton plots shows that deformation is probably both diffusion and dislocation controlled. However, further work is needed to stablish deformation and degradation micro mechanisms in the studied creep regime.
The creep behavior of single-crystals of the nickel-base superalloy CMSX-4 was investigated at 1288°C, which is the temperature of the hot isostatic pressing (HIP) treatment applied to this superalloy in the industry. It was found that at this super-solvus temperature, where no Gamma’-strengthening occurs, the superalloy is very soft and rapidly deforms under stresses between 4 and 16 MPa. The creep resistance was found to be very anisotropic, e.g. the creep rate of [001] crystals was about 11 times higher than that of a [111] crystal. The specimens of different orientations also showed a very different necking behavior. The reduction of the cross-section area psi of [001] crystals reached nearly 100%, while for a [111] crystal psi=62%. The EBSD analysis of deformed specimens showed that despite such a large local strain the [001] crystals didn’t not recrystallize, while a less deformed [111] crystal totally recrystallized within the necking zone. From the shape of deformed specimens and TEM investigations it was concluded that the main strain contribution resulted from <011> {111} octahedral slip.
Porosity in single-crystal nickel-base superalloys is removed by hot isostatic pressing (HIP) at temperatures above gamma’-solvus where the material is very soft and ductile. For example, single-crystal nickel-base superalloy CMSX-4 is HIPed at temperature 1288 °C, which is slightly higher than the gamma’-solvus temperature of this alloy equal to about 1280 °C. It is assumed that pore shrinking during HIP is mostly due to dislocation creep. Such a modelling of HIP of CMSX-4 was started in our group on the base of results of creep tests of [001] single-crystals at 1288 °C [1]. However, it was found later [2] that the alloy CMSX-4 shows very strong creep anisotropy at 1288 °C. Therefore, for calibration of the creep law, creep tests of different orientations under different stress levels are required at the HIP temperature. This was the main task of present work. Single-crystals of CMSX-4 of axial orientations [001], [011], [123] and [111] were cast by VIAM Moscow and tested by BAM Berlin under creep conditions at 1288 °C and stress levels between 4 MPa and 16 MPa. At all stress levels, the creep rate increases by an order of magnitude when changing the orientation from [001] to [111] with [011] and [123] orientations in between. Such a character of creep anisotropy corresponds to the orientation dependence of the Schmid factor for octahedral glide.
The crystal viscoplasticity model developed in [1] was improved to better represent the time induced softening observed during creep. The creep tests for different stresses and orientations as well as pore closure were simulated. The results of pore closure simulation are compared with measurements of porosity decrease during Hiping.
This presentation shows some experimental results of the characterization of the creep behavior of LPBF 316L, which has been poorly studied and understood to date. The presentation includes results regarding the mechanical properties, the initial microstructural state and its evolution under loading, and the damage mechanism. This work was done within the BAM focus area materials project AGIL. As a benchmark to assess the material properties of the LPBF 316L, a conventionally manufactured variant was also tested.
Creep and fracture behavior of conventionally and additively manufactured stainless steel 316L
(2020)
A critical task within the frame of establishing process-structure-property-performance relationships in additive manufacturing (AM) of metals is producing reliable and well-documented material behavior’s data and knowledge regarding the structure-property correlation, including the role of defects. After all, it represents the basis for developing more targeted process optimizations and more reliable predictions of performance in the future. Within this context, this contribution aims to close the actual gap of limited historical data and knowledge concerning the creep behavior of the widely used austenitic stainless steel 316L, manufactured by Laser-Powder-Bed-Fusion (L-PBF). To address this objective, specimens from conventional hot-rolled and AM material were tested under application-relevant conditions according to existing standards for conventional material, and microstructurally characterized before and after failure. The test specimens were machined from single blocks from the AM material. The blocks were manufactured using a standard scan and build-up strategy and were subsequently heat-treated. The creep behavior is described and comparatively assessed based on the creep lifetime and selected creep curves and characteristic values. The effect of defects and microstructure on the material’s behavior is analyzed based on destructive and non-destructive evaluations on selected specimens. The AM material shows shorter creep lives, reaches the secondary creep stage much faster and at a lower strain, and features lower creep ductility compared to its conventional counterpart. The creep damage behavior of the AM material is more microstructure than defect controlled and is characterized by the formation and accumulation of single intergranular damage along the whole volume. Critical features identified are the grain morphology and the grain-boundary as well as the dislocation’s density. Micro-computed tomography (µCT) proves to be an alternative to metallography to analyze the creep damage.
This contribution provides current findings regarding materials susceptibility for CCUS applications. Basing on results gathered in 2 German long-term projects (COORAL and CLUSTER) suitable materials are introduced as well as dominating impurities of the CO2 stream and corrosion mechanisms. Investigations cover the whole CCUS process chain and provide the following recommendations for certain parts. Commercially available carbon steels are suitable for compression and pipelines as long as moisture content and impurities are limited (water 50 to 100 ppmv, SO2 and NO2 ca. 100 ppmv).
Corrosion rates increase with increasing water content (0.2 – 20 mm/a).
Condensation of acids and therefore droplet formation is always possible, even at low water contents.
A low SO2 content within the CO2-stream might be more important than a low water content.
Cr13-steels showed a general susceptibility to shallow pitting and pitting. So, they seem to be not suitable for CCUS applications.
Low alloyed steels showed better corrosion behavior (predictable uniform corrosion).
For direct contact with saline aquifer fluids only high alloyed steels shall be used.
To apply high-entropy alloys (HEA) of the CrMnFeCoNi family in challenging atmospheres, their degradation behavior under harsh environments needs to be investigated. Oxidation studies to HEAs have not been extensively investigated and most of them are concentrated on environments like synthetic air, laboratory air, CO/CO2, O2 and H2O atmospheres. Main corrosion products which were identified after aging times of up to 100 h are Mn2O3 (≤800°C) and Mn3O4 (≥800°C).
Another corrosive medium in high temperature applications is SO2, which preferentially forms sulfides on commercial steels for example. These can be occurred both in the oxide layer and at the oxide/metal interface. For instance, on Fe-Cr based alloys sulfides (Cr5S6) were detected along grain boundaries and their number increases with exposure time and Cr-content in the alloy. These sulfides show an increased hardness, compared to the bulk alloy, and cause an embrittlement of the grain boundaries. This is a serious material degradation phenomenon, now addressed for the case of HEAs.
In the present study metal sulfides were identified after corrosion of the HEA CrMnFeCoNi alloy in an Ar-0.5vol.%SO2 atmosphere at 800°C for 24 h, 48 h, 96 h and 192 h exposure time. After all three duration times, a thin non-protective Cr2O3 layer has formed at the oxide/alloy interface. At the gas side a thick Mn3O4 layer with local voids containing sulfur could be detected by SEM-EDS analysis. Furthermore, S precipitates could be detected in the bulk material near the surface. These sulfides were characterized in detail by scanning and transmission electron microscopy. Based on these results, a model for grain boundary sulfidation of high-entropy alloy CrMnFeCoNi is discussed.