4 Material und Umwelt
Filtern
Dokumenttyp
- Zeitschriftenartikel (258)
- Buchkapitel (3)
- Beitrag zu einem Tagungsband (2)
- Forschungsbericht (2)
- Beitrag zu einem Sammelband (1)
Sprache
- Englisch (266) (entfernen)
Referierte Publikation
- ja (266) (entfernen)
Schlagworte
- Leaching (14)
- Biocides (10)
- Phosphorus (9)
- Sewage sludge (9)
- Bacteria (8)
- Antimicrobial resistance (6)
- Biofilm (6)
- Bottom ash (6)
- Circular economy (6)
- Construction products (6)
- Biofilms (5)
- DRIFTS (5)
- Degradation (5)
- Ectoine (5)
- Fungi (5)
- Thermal desorption (5)
- Black fungi (4)
- Corrosion (4)
- Fertilizer (4)
- Gas chromatography (4)
- Geosynthetics (4)
- Geotextiles (4)
- Non-invasive analysis (4)
- Pathogen (4)
- Phosphorus recovery (4)
- Polyethylene (4)
- Raman spectroscopy (4)
- Reverse glass painting (4)
- VOC (4)
- Wastewater (4)
- X-ray absorption near-edge structure (XANES) spectroscopy (4)
- XANES spectroscopy (4)
- Archaeometry (3)
- Bio-weathering (3)
- Biodeterioration (3)
- Diffusive gradients in thin films (DGT) (3)
- Disinfection (3)
- Emission test chamber (3)
- Evolution (3)
- Fertilzer (3)
- Indoor air quality (3)
- Interlaboratory comparison (3)
- Knufia petricola (3)
- NAP-XPS (3)
- Osmoadaptation (3)
- PFAS (3)
- Papyrus (3)
- Phosphorus fertilizer (3)
- Renewable Energy, Sustainability and the Environment (3)
- Scandium (3)
- Sewage sludge ash (3)
- Soil (3)
- Standardisation (3)
- Struvite (3)
- Symbiosis (3)
- TXRF (3)
- Termite (3)
- Thermal treatment (3)
- Ultrafine particles (3)
- VVOC (3)
- Volatile organic compounds (3)
- Wood Protection (3)
- Wood protection (3)
- Aerosol (2)
- Air pollution (2)
- Air quality monitoring (2)
- Air sampling (2)
- Analytical methods (2)
- Atomic and Molecular Physics and Optics (2)
- Bacterial adhesion (2)
- Biocorrosion (2)
- Biofilm formation (2)
- Biofouling (2)
- Biogenic weathering (2)
- Bioinformatics (2)
- Bioreceptivity (2)
- Building and Construction (2)
- Cannibalism (2)
- Cascade impactor (2)
- Combustion ion chromatography (CIC) (2)
- Condensed Matter Physics (2)
- Coptic (2)
- DHN melanin (2)
- DNA (2)
- Design of experiments (2)
- Ecotoxicity (2)
- Emission (2)
- Energy Engineering and Power Technology (2)
- Entomopathogen (2)
- Environment (2)
- Extracellular polymeric substances (2)
- Extractable organically bound fluorine (EOF) (2)
- Fluoride (2)
- Forsterite (2)
- Fuel Technology (2)
- Fungus (2)
- Gut microbiota (2)
- Halomonas elongata (2)
- High resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS) (2)
- Horizontal gene transfer (2)
- ICP-MS (2)
- ISO 16000-6 (2)
- Immunity (2)
- Incineration bottom ash (2)
- Insect biotechnology (2)
- Isoptera (2)
- Keratin (2)
- Laser processing (2)
- Laser-induced periodic surface structures (LIPSS) (2)
- Leaching control mechanisms (2)
- Leaching tests (2)
- MIC (2)
- MOF (2)
- Magnesium (2)
- Manuscripts (2)
- Marine littering (2)
- Mechanochemistry (2)
- Melting experiments (2)
- Metabolomics (2)
- Methanogen (2)
- Method development (2)
- Microbiologically influenced corrosion (2)
- Microbiota (2)
- Microcolonial fungi (2)
- Micropatterning (2)
- Microplastic (2)
- Mixed ink (2)
- NanoSIMS (2)
- Nosema ceranae (2)
- Osmia bicornis (2)
- Particles (2)
- Passive sampling (2)
- Per- and Polyfluoroalkyl substances (PFAS) (2)
- Pigment identification (2)
- Polyglycerol (2)
- Pseudomonas aeruginosa (2)
- Recycling (2)
- Recycling fertilizer (2)
- Reference material (2)
- Social (2)
- Substance release (2)
- Termites (2)
- Tineola bisselliella (2)
- Transcriptomics (2)
- Transformation (2)
- Virology (2)
- Virulence (2)
- Waste-to-energy (2)
- Weathering (2)
- Wild bees (2)
- X-ray diffraction (2)
- XANES (2)
- XPS (2)
- (Semi)arid to humid-temperate natural ecosys (1)
- 13CO2 pulse labeling (1)
- 16S rRNA gene (1)
- 3D inspection (1)
- 3D printer (1)
- 3D printing (1)
- A key interface (1)
- A-DNA conformation (1)
- AEROMET II (1)
- AEROMET project (1)
- Accelerated aging (1)
- Accuracy (1)
- Adaptation (1)
- Adaption (1)
- Additive Manufacturing (1)
- Adipokinetic hormone (1)
- Adipokinetic hormone receptor (1)
- Adsorbable organically bound fluorine (AOF) (1)
- Advanced groups of termites (1)
- Aerodynamic levitation (1)
- Aerosol gravimetry (1)
- Aerosol measurement instruments (1)
- Aerosols (1)
- Aerosolsensor (1)
- Affinity chromatography (1)
- Ag-LDI-MS (1)
- Aging (1)
- Aging tests (1)
- Agricultural mycology (1)
- Agronomic performance (1)
- Air analysis (1)
- Air pollution control (1)
- Alexander von Humboldt (1)
- Alkylating agents (1)
- Ambient aerosols (1)
- Ammonium (1)
- Amphiphilic polymer (1)
- Amplicon sequencing (1)
- Anaerobic pathways (1)
- Analytical Chemistry (1)
- Analytical screening techniques (1)
- Animal immune system (1)
- Anobium punctatum (1)
- Antagonism (1)
- Antibacterial (1)
- Antibacterial coatings (1)
- Antibacterial polymer (1)
- Antibacterial surfaces (1)
- Antibiotic resistance (1)
- Antibiotics (1)
- Antibodies (1)
- Antifouling (1)
- Antimicrobial (1)
- Antimicrobial coating (1)
- Antimicrobial materials (1)
- Antimicrobial surfaces (1)
- Antimicrobial test (1)
- Antimicrobial testing (1)
- Antimicrobials (1)
- Antimony (1)
- Antiseptic agents (1)
- Aquatic fungi (1)
- Aqueous synthesis (1)
- Arbuscular mycorrhiza (1)
- Archaea (1)
- Architecture (1)
- Artificial ageing (1)
- Artificial weathering (1)
- Ascosphaera apis (1)
- AshDec (1)
- Aspergillus (1)
- Assessment (1)
- Automated analysis (1)
- BEMMA (1)
- BESSY (1)
- BODIPY (1)
- BOFS (1)
- BTEX (1)
- Bacillus subtilis (1)
- Bacterial attachment (1)
- Bacterial cell cycle (1)
- Bacterial second messenger (1)
- Baltic Sea (1)
- Basidiomycetes (1)
- Bassanite (1)
- Batch tests (1)
- Bathyarchaeia (1)
- Bauxite Residue (1)
- Bauxite residue (1)
- Bawit (1)
- Bee (1)
- Bee diseases (1)
- Bee health (1)
- Behavioural mechanisms (1)
- Beneficial microbes (1)
- Beschichtung (1)
- Bio-based insulation (1)
- Bioceramics (1)
- Biocide tolerance (1)
- Biodeterioration and biodegradation (1)
- Biofilm quantification (1)
- Bioinformatics virology viruses software (1)
- Biological pest control (1)
- Biologically induced mineral weathering (1)
- Biomimetic (1)
- Biosynthesis (1)
- Biotests (1)
- Biotic environment (1)
- Biphasic growth (1)
- Black microcolonial fungi (1)
- Black writing ink (1)
- Blast-furnace sludge (1)
- Blattodea (1)
- Botrytis cinerea (1)
- Brown-rot fungi (1)
- Building Material (1)
- Building materials (1)
- Built environment (1)
- Bushveld Complex (1)
- C-di-GMP (1)
- CCQM (1)
- CEC-L-103 (1)
- CHC (1)
- COST action CA15114 AMICI (1)
- CPC calibration (1)
- CRISPR/Cas9 (1)
- CaNaPO4 (1)
- Calcium alkali phosphate (1)
- Calcium carbonate (1)
- Calcium silicate (1)
- Calcium sulfate (1)
- Calibration transfer (1)
- Carbon ink (1)
- Carbon steel (1)
- Carbon steel corrosion (1)
- Cell appendages (1)
- Cell studies (1)
- Cell-envelope (1)
- Cellulose ether (1)
- Cellulose synthase (1)
- Cerium oxide (1)
- Characterisation (1)
- Chemical analysis (1)
- Chemical durability (1)
- Chemical ecology (1)
- Chemical extraction (1)
- Chemical extraction methods (1)
- Chemical recycling (1)
- Chemicals (1)
- Chicken manure ash (1)
- Chilean Coastal Cordillera (1)
- Chlorine (1)
- Chromitites (1)
- Circular Economy (1)
- Clean steel (1)
- Cleridae (1)
- Climate gradient (1)
- Cloning vectors (1)
- Close proximity to colonies (1)
- Coastal protection (1)
- Cobalt (1)
- Cockroach (1)
- Cockroaches (1)
- Codex (1)
- Cognitive performance (1)
- Coleoptera (1)
- Colored glasses (1)
- Colourants (1)
- Combustion Ion Chromatography (1)
- Combustion and gasification (1)
- Combustion ion chromatography (1)
- Community composition (1)
- Community-level interactions (1)
- Comparison (1)
- Compatible solute (1)
- Comsumer good samples (1)
- Concept (1)
- Concrete (1)
- Confocal microscopy (1)
- Conjugate (1)
- Conjugation (1)
- Conservation (1)
- Construction materials (1)
- Construction product (1)
- Construction products regulation (CPR) (1)
- Consumer products (1)
- Contamination (1)
- Contraction (1)
- Control (1)
- Copper-based wood preservatives (1)
- Coptic manuscripts (1)
- Corundum (1)
- Critical raw materials (1)
- Cross-feeding (1)
- Cross-resistance (1)
- Cross-sectioning (1)
- Cryo XPS (1)
- Crystalline phase identification (1)
- Crystallization (1)
- CuNPs (1)
- Cultural heritage (1)
- Cupriavidus campinensis (1)
- Cuticular hydrocarbons (1)
- Cyanobacteria (1)
- DNA polymerase (1)
- DSM 5009 (1)
- De novo assembly (1)
- Dead Sea Scrolls (1)
- Decomposition point (1)
- Degradable polymer (1)
- Dendrimer (1)
- Denitrification (1)
- Density separation (1)
- Desert ecology (1)
- Developing building materials (1)
- Dielectric heating (1)
- Dietary adaptation (1)
- Differential expression (1)
- Differential gene expression analysis (1)
- Diffractive gratings (1)
- Diffusive Gradients in Thin-films (DGT) (1)
- Diffusive Gradients in thin films (DGT) (1)
- Diffusive gradients in thin-films (DGT) (1)
- Direct laser writing (1)
- Disease (1)
- Disinfection Fuel (1)
- Disposal (1)
- Diversity (1)
- Dothideomycetes (1)
- Draft Genome (1)
- Drawings (1)
- Driving rain (1)
- Dry treatment (1)
- Drywood termite (1)
- DsRNA (1)
- Dye (1)
- Dynamic calibration gas mixtures (1)
- Dynamic surface leaching test (1)
- E. coli (1)
- EAF slags (1)
- EN 717-3 (1)
- Earthen building materials (1)
- Ecotoxicity tests (1)
- Ecotoxicological tests (1)
- Ecotoxixity (1)
- Efficacy (1)
- Egypt (1)
- Electric arc furnace (EAF) slags (1)
- Electric arc furnace dust (1)
- Electric arc furnace slags (1)
- Electron microscopy (1)
- Electronic (1)
- Element mass concentration (1)
- Elemental aerosol analysis (1)
- Elemental composition (1)
- Eluates (1)
- Emerging (1)
- Emission chamber (1)
- Emission test method (1)
- Emission testing (1)
- Enamels (1)
- Entomopathogenic Fungus (1)
- Entropy (1)
- Environmental Chemistry (1)
- Environmental Engineering (1)
- Environmental assessment (1)
- Environmental conditions (1)
- Environmental evaluation (1)
- Environmental impact (1)
- Environmental simulations (1)
- Epidemal layer (1)
- Eurotiomycetes (1)
- Exocrine gland (1)
- Expansion (1)
- Exposure (1)
- External (1)
- Extracellular enzymes (1)
- Extractable organic fluorine (1)
- Extraction (1)
- Extremophile (1)
- Extremophiles (1)
- F pili (1)
- FAT class concept (1)
- FFF-3D printer (1)
- FFF-3D printing (1)
- FFF-filament (1)
- FFF-printing (1)
- FactSage calculations (1)
- FactSageTM calculations (1)
- Family archives (1)
- Faraday cup aerosol electrometer (1)
- Fatigue (1)
- Fenton-like reaction (1)
- Fire-retardant paint (1)
- Flask method (1)
- Flexible shadow masks (1)
- Flow system (1)
- Fluorescence (1)
- Fluorescence spectroscopy (1)
- Fluorescent microscopy (1)
- Fluorolytic sol-gel synthesis (1)
- Food (1)
- Food fermentation (1)
- Forest fires (1)
- Forest soils (1)
- Formaldehyde (1)
- Formation enthalpy (1)
- Fractal structure (1)
- Fuel sorption (1)
- Fungal decay (1)
- Fungal stress mechanisms and responses (1)
- Fungiculture (1)
- Fusarium (1)
- GC-FID (1)
- GC-MS (1)
- GDL (1)
- GNBP-2 (1)
- Gas analysis (1)
- Gene expression (1)
- General Chemistry (1)
- General Environmental Science (1)
- General Materials Science (1)
- General Medicine (1)
- Genetics (1)
- Genome (1)
- Genome sequence (1)
- Genomics (1)
- Geobiology (1)
- Geology (1)
- Geomembranes (1)
- Glass scanning (1)
- Global radiation (1)
- Graphene (1)
- Graphene–bacteria interaction (1)
- Green facades (1)
- Groundwater (1)
- Grouts (1)
- Growth-rate homeostasis (1)
- Gut symbionts (1)
- Gypsum (1)
- Gypsum plasterboards (1)
- Gypsum waste (1)
- Halogenation (1)
- Halophile (1)
- Halophilic bacteria (1)
- Hazardous waste (1)
- Haze Samples (1)
- Hazenite (1)
- Health, Toxicology and Mutagenesis (1)
- Healthcare (1)
- Heat capacity (1)
- Heat maps (1)
- Heavy metal free (1)
- Heavy metal removal (1)
- Heavy metals (1)
- Hellenistic (1)
- Herbaspirillum seropedicae (1)
- Hermopolis (1)
- High density polyethylene (1)
- History of Art (1)
- Honey bee (1)
- Honeybee (1)
- Hospital premises (1)
- Host and symbiont ecology (1)
- Host immunity (1)
- Hydration products (1)
- Hydrogen storage (1)
- Hygienic behavior (1)
- Hyperarid (1)
- Hypermutation (1)
- Hypopharynx (1)
- ICP-OES (1)
- IR spectroscopy (1)
- ISO 22196 (1)
- ISO REMCO (1)
- ITS region (1)
- Idiopathic environmental intolerance (1)
- Immune gene prediction (1)
- ImmunoDB (1)
- In situ (1)
- In situ synchrotron x-ray diffraction (1)
- In-situ Process Monitoring (1)
- In-situ analysis (1)
- Incubated soil/fertilizer mixtures (1)
- Indirect photolysis (1)
- Indoor Air: Adsorbent performance (1)
- Indoor air (1)
- Indoor mycobiome (1)
- Industrial and Manufacturing Engineering (1)
- Industrial mycology (1)
- Infecting a number of insects, (1)
- Infections (1)
- Infrared spectroscopy (1)
- Infrared thermography (1)
- Ink (1)
- Ink analysis (1)
- Insect evolution (1)
- Insecticide (1)
- Instrumentation (1)
- Inter-comparison (1)
- Inter-lab comparison (1)
- Inter-laboratory test (1)
- Intercomparison (1)
- Interdisciplinarity (1)
- Internal pores (1)
- Intraparticle diffusion (1)
- Intumescent coating (1)
- Ionic liquid (1)
- Ir DNA staining approach (1)
- Iron gall ink (1)
- Iron making (1)
- Iron scrap (1)
- Iron-gall ink (1)
- Isotopes (1)
- Issues (1)
- Joint grouts (1)
- Knock-out mutant (1)
- Korynetes caeruleus (1)
- LC-MS/MS (1)
- Laboratory breeding (1)
- Labrum (1)
- Laccase (1)
- Landfill (1)
- Landfill lining (1)
- Laser printer emission (1)
- Laser-induced nanostructures (1)
- Laser-modified surface (1)
- Layer-by-Layer (1)
- Life history data (1)
- Lifetime (1)
- Lignocellulose (1)
- Limit values (1)
- Low melting glasses (1)
- Low-molecular-weight organic substances (1)
- Luftgüte (1)
- Lysimeter (1)
- MSWI bottom ash (1)
- MSWI fly ash (1)
- Major transition (1)
- Marble (1)
- Marek's Disease Virus (1)
- Marek's virus (1)
- Mask fabrication (1)
- Mass spectrometry (1)
- Materials Chemistry (1)
- Mathematical analysis (1)
- Mechanisms of pathogenesis (1)
- Mechanosensitive channel (1)
- Medical mycology (1)
- Melanin (1)
- Melanin Adhesion (1)
- Melting point (1)
- Melting temperature (1)
- Metabolic engineering (1)
- Metabolic flux analysis (1)
- Metabolic modeling (1)
- Metabolism (1)
- Metadata (1)
- Metal recovery (1)
- Metals and Alloys (1)
- Metarhizium (1)
- Metarhizium robertsii DSM 1490 (1)
- Methane (1)
- Methanogens (1)
- Microbe (1)
- Microbial adhesions (1)
- Microbial simulation, (1)
- Microbially induced carbonate precipitation (MICP) (1)
- Microbiological influenced corrosion MIC (1)
- Microbiologically influenced corrosion (MIC) (1)
- Microchamber (1)
- Micromonospora aurantiaca (1)
- Microwaves (1)
- Millipedes (1)
- Mineral (1)
- Mining (1)
- Mixture toxicity (1)
- Model (1)
- Model aerosols (1)
- Modeling (1)
- Modelling studies (1)
- Modified mycotoxins (1)
- Moisture (1)
- Moisture performance (1)
- Molecular Organic Frameworks (1)
- Molecular clock (1)
- Molecular identification (1)
- Molybdenum (1)
- Monoterpene (1)
- MscS (1)
- Mud volcanoe fluids (1)
- Multi-resistant bacteria (1)
- Multi-scale study (1)
- Multicellularity (1)
- Multidisciplinary (1)
- Multiple Displacement Amplification (1)
- Multiple chemical sensitivity (1)
- Multiple lines of evidence (1)
- Multiport (1)
- Municipal sewage sludge (1)
- Mussel-inspired coating (1)
- Mussel-inspired materials (1)
- Mutation rate (1)
- MySpot (1)
- Mycotoxin (1)
- Müllverbrennung (1)
- N and K analog tracer (1)
- NGS (1)
- NIR imaging (1)
- Nano (1)
- Nano Particles (1)
- Nano-Fourier-transform infrared spectroscopy (1)
- Nano-materials (1)
- Nanobiocide (1)
- Nanocoating (1)
- Nanomaterial (1)
- Nanomaterials (1)
- Nanoparticle (1)
- Nanoparticles (1)
- Nanopowder (1)
- Natural durability (1)
- Natural ecosystems (1)
- Near ambient x-ray photoelectron spectroscopy (1)
- Near-infrared refectography (1)
- Neuropeptide (1)
- New exocrine organ (1)
- Next generation sequencing (1)
- Nickel (1)
- Nitrification inhibitor (1)
- Nitrososphaerales (1)
- Nitrous oxide (1)
- Non-destructiv testing (1)
- Non-destructive Materials (1)
- Non-ferrous metals (1)
- Non-invasive (1)
- Non-vitriolic iron-gall inks (1)
- Nonspecific binding (NSB) (1)
- Nonvolatile (1)
- Nostoc punctiforme (1)
- Nutrient (1)
- Nutrient acquisition (1)
- Nutrient cycles (1)
- Nutrient uplift and recyclin (1)
- OECD (1)
- OIT (1)
- Oddy test (1)
- Oil (1)
- Oil and gas industry (1)
- Olivine (1)
- One-step ionic liquids synthesis (1)
- Open data (1)
- Optical and Magnetic Materials (1)
- Organic contaminants (1)
- Organic phosphorus breakdown (1)
- Osmotic shock (1)
- Osteogenesis (1)
- Oxide melts (1)
- P sink method (1)
- P speciation (1)
- P-efficiency (1)
- P. Fluorescens (1)
- PM monitors (1)
- PV modules (1)
- Painting (1)
- Particle emission (1)
- Particle size distribution (1)
- Particle synthesis (1)
- Partikel (1)
- Parylene C (1)
- Pathogen spillover (1)
- Pathogen transmission (1)
- Pathogen virulence (1)
- Peptide-derived components (1)
- Per- and polyfluorinated alkly substances (PFASs) (1)
- Per- and polyfluorinated alkyl substances (PFASs) (1)
- Per- and polyfluoroalkyl substances (PFAS) (1)
- Performance (1)
- Permeability (1)
- Persistence (1)
- Pest control (1)
- Pesticides (1)
- Phase formation (1)
- Phase transformation (1)
- Phenotypic heterogeneity (1)
- Phenotypic variation (1)
- Phoshpor availability (1)
- Phosphate dynamics (1)
- Phosphate extractability and availability (1)
- Phosphorous recovery (1)
- Phosphorus K-edge-XANES spectroscopy (1)
- Phosphorus availability (1)
- Phosphorus elimination (1)
- Phosphorus plant-availability (1)
- Phosphous recovery (1)
- Photodynamic therapy (1)
- Photometric P determination (1)
- Photonics (1)
- Phototrophs (1)
- Phyllosphere (1)
- Pigment (1)
- Pilot comparison (1)
- Plant Experiment (1)
- Plant availability (1)
- Plant economic spectrum (1)
- Plant pathogen (1)
- Plastic degradation (1)
- Plastic waste (1)
- Platinum (1)
- Pollutant (1)
- Pollution (1)
- Polydopamine (1)
- Polyelektrolyt (1)
- Polyethylene terephthalate (1)
- Polyioinic liquid (1)
- Polymer-based products (1)
- Polymerase mutant (1)
- Polypropylene (1)
- Polystyrene (1)
- Polyurethanes (1)
- Porosity (1)
- Pot experiments (1)
- Potential toxic elements (1)
- Probiotic-based vaccines (1)
- Probiotics (1)
- Process Metallurgy (1)
- Process development (1)
- Process upscaling (1)
- Proficiency testing (1)
- Proofreading deficient (1)
- Prospective risk assessment (1)
- Proteome (1)
- Pseudomonas fluorescens (1)
- Pseudomonas veronii (1)
- Ptinidae (1)
- Public Health, Environmental and Occupational Health (1)
- Purification (1)
- Pyrolysis (1)
- Quasispecies (1)
- RNA extraction (1)
- RNA interference (1)
- RNA-Seq (1)
- RNA-Sequencing (1)
- RNAi (1)
- Radio waves (1)
- Radon (1)
- Radon exhalation (1)
- Raman (1)
- Raman Spectroscopy (1)
- Reactive oxygen species (1)
- Reactor conditions (1)
- Real-time qPCR (1)
- Recovery (1)
- Recovery potential (1)
- Recovery rate (1)
- Recycled gypsum (1)
- Recycled sources (1)
- Red Mud (1)
- Red mud (1)
- Reductive decomposition (1)
- Reductive defluorination (1)
- Reference materials (1)
- Reference method (1)
- Reference organisms (1)
- Reference samples (1)
- Regulation (1)
- Rembrandt (1)
- Remediation (1)
- Resistance model (1)
- Resource Recovery (1)
- Resources (1)
- Restoration and conservation (1)
- Reverse paintings on glass (1)
- Rhenanite (1)
- Rhizopus (1)
- Rhizopus and Aspergillus oryzae (1)
- Rhizosphere effect (1)
- Rhizosphere processes (1)
- Rice (1)
- Robustness validation (1)
- Rock biofilm (1)
- Rock leaching (1)
- Root economics space (1)
- Rostral gland (1)
- Round robin test (1)
- Rround robin test (1)
- Ruthenium (1)
- SEM (1)
- SEM micrography (1)
- SIMS (1)
- SVOC (1)
- Safety (1)
- Salts (1)
- Sample preparation (1)
- Sapphire (1)
- Sc recovery (1)
- Sc-ICP-ToF-MS (1)
- Scanning micro-X-ray fluorescence (1)
- Scattering (1)
- Scattering-type scanning near-field optical microscopy (s-SNOM) (1)
- Scribal corrections (1)
- Secondary P-fertilizer (1)
- Secondary building materials (1)
- Secondary metabolites (1)
- Selective Chlorination (1)
- Selective chlorination (1)
- Selective quantification (1)
- Self-assembled monolayer (1)
- Self-assembled monolayers (SAM) (1)
- Semivolatile organic compounds (1)
- Sensors (1)
- Sequence annotation (1)
- Sewage Sludge (1)
- Sewage Sludge Ashes (1)
- Sewage sludge ash (SSA) (1)
- Sewage sludge disposal (1)
- Shale (1)
- Short crack propagation (1)
- Silica and polystyrene nanoparticles (1)
- Silicate (1)
- Silicon carbide (1)
- Silver (1)
- Single cell (1)
- Single cell microbiology (1)
- Size exclusion chromatography (1)
- Size resolved chemical composition (1)
- Social Immunity (1)
- Social immunity (1)
- Social insect (1)
- Sociality (1)
- Software (1)
- Soil contact (1)
- Soil incubation study (1)
- Soil-feeding habit (1)
- Soil-like material (1)
- Soils (1)
- Solar panels (1)
- Soldier (1)
- Solid phase extraction (SPE) (1)
- Solid-liquid extraction (1)
- Solid-phase extraction (SPE) (1)
- Solitary bees (1)
- Solute excretion (1)
- Solvents (1)
- Solvolysis (1)
- Sorption (1)
- Spectroscopy (1)
- Stained glass (1)
- Standardization (1)
- Steelmaking residues (1)
- Stoichiometric homeostasis (1)
- Stone cultural heritage (1)
- Stop/flow experiments model (1)
- Strategy and Management (1)
- Stress conditions (1)
- Stress tolerance (1)
- Structured light scanning (1)
- Sub-4nm particles (1)
- Subaerial biofilm (1)
- Subaerial biofilms (1)
- Subjective complaints (1)
- Subsocial (1)
- Subsoil nutrient tracing (1)
- Sugar cane bagasse (1)
- Sum parameter (1)
- Suppression (1)
- Surface interactions (1)
- Surface water (1)
- Surface waters (1)
- Survival rates (1)
- Synchrotron (1)
- Synchrotron radiation (1)
- Synergy (1)
- Synthesis (1)
- Synthetic metabolism (1)
- Synthetic organic pigments (1)
- Systematics (1)
- Targeted and nontargeted (1)
- Taxonomy (1)
- Temperate rain forest (1)
- Temple Scroll (1)
- Tems (1)
- Terbutryn (1)
- Termitoidae (1)
- Thermal analysis (1)
- Thermal degradation (1)
- Thermo-desorption (1)
- Thermochemical treatment (1)
- Thermocouple (1)
- Thermodynamic (1)
- Thioimidazolium (1)
- Time resolved chemical composition (1)
- Torah scrolls (1)
- Touch surfaces (1)
- Tripartite interactions (1)
- UV radiation (1)
- UV-irradiation (1)
- Ultrastructure (1)
- Umweltmessung (1)
- Up-cycling (1)
- Ureolytic bacteria (1)
- Utilisation (1)
- VOC emission (1)
- Validation trial (1)
- Vanadium (1)
- Virus (1)
- Viruses (1)
- Vitriolic iron-gall inks (1)
- Waste incineration (1)
- Waste management (1)
- Waste treatment (1)
- Water (1)
- Water atmosphere (1)
- Water contact (1)
- Water stable isotope analysis (1)
- Water uptake (1)
- Weld fatigue (1)
- Weld toe geometry (1)
- White-rot fungi (1)
- Wood Modification (1)
- Wood ash (1)
- Wood samples (1)
- Wooden toys (1)
- Writing materials (1)
- X-Ray analysis (1)
- X-ray adsorption near-edge structure (XANES) spectroscopy (1)
- X-ray diffraction (XRD) (1)
- X-ray fuorescence (1)
- X-ray spectroscopy (1)
- X-ray tomographic (1)
- XRF (1)
- XRF imaging (1)
- XRF ink analysis (1)
- Yeast (1)
- ZIF (1)
- ZIF-8 (1)
- Zearalenone (1)
- Zearalenone sulfate (1)
- Zeolithe (1)
- Zinc (1)
- Zinc chloride (1)
- Zinc oxide (1)
- a-zearalenol (1)
- dsDAN monolayer (1)
- fertilizer (1)
- iChip (1)
- mRNA-seq (1)
- microspectroscopy (1)
- pH probe (1)
- qPCR (1)
- soil (1)
- x-ray diffraction (1)
- ‘Green’ pesticide (1)
Organisationseinheit der BAM
- 4 Material und Umwelt (266)
- 4.1 Biologische Materialschädigung und Referenzorganismen (78)
- 4.3 Schadstofftransfer und Umwelttechnologien (55)
- 4.0 Abteilungsleitung und andere (54)
- 4.4 Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung (45)
- 4.2 Material-Mikrobiom Wechselwirkungen (32)
- 1 Analytische Chemie; Referenzmaterialien (28)
- 6 Materialchemie (27)
- 4.5 Kunst- und Kulturgutanalyse (20)
- 1.7 Organische Spuren- und Lebensmittelanalytik (12)
- 6.1 Oberflächen- und Dünnschichtanalyse (10)
- 1.4 Prozessanalytik (9)
- 6.3 Strukturanalytik (8)
- 5 Werkstofftechnik (6)
- 6.2 Material- und Oberflächentechnologien (6)
- 1.1 Anorganische Spurenanalytik (5)
- 1.8 Umweltanalytik (5)
- 7 Bauwerkssicherheit (5)
- 5.4 Multimateriale Fertigungsprozesse (4)
- 1.2 Biophotonik (3)
- 4.6 Molekulare und angewandte Entomologie (3)
- 7.1 Baustoffe (3)
- 7.4 Baustofftechnologie (3)
- 8 Zerstörungsfreie Prüfung (3)
- 8.0 Abteilungsleitung und andere (3)
- 1.0 Abteilungsleitung und andere (2)
- 5.3 Polymere Verbundwerkstoffe (2)
- 6.6 Physik und chemische Analytik der Polymere (2)
- 9 Komponentensicherheit (2)
- 1.5 Proteinanalytik (1)
- 1.6 Anorganische Referenzmaterialien (1)
- 1.9 Chemische und optische Sensorik (1)
- 3 Gefahrgutumschließungen; Energiespeicher (1)
- 3.1 Sicherheit von Gefahrgutverpackungen und Batterien (1)
- 5.1 Mikrostruktur Design und Degradation (1)
- 5.2 Metallische Hochtemperaturwerkstoffe (1)
- 6.0 Abteilungsleitung und andere (1)
- 6.7 Materialsynthese und Design (1)
- 7.5 Technische Eigenschaften von Polymerwerkstoffen (1)
- 8.5 Röntgenbildgebung (1)
- 9.0 Abteilungsleitung und andere (1)
- 9.3 Schweißtechnische Fertigungsverfahren (1)
- 9.4 Integrität von Schweißverbindungen (1)
- S Qualitätsinfrastruktur (1)
- S.0 Abteilungsleitung und andere (1)
Paper des Monats
- ja (18)
In 2018, the production of Municipal SolidWaste (MSW) in EU-28 reached 250.6 Mt, with the adoption of different management strategies, involving recycling (48 wt %), incineration and thermal valorization (29 wt %) and landfilling (23 wt %). This work was based on the analysis of the baseline situation of MSW management in EU-28 in 2018, considering its progress in 2008–2018, and discussed the possible improvement perspectives based on a framework involving incineration and recycling as the only possible alternatives, specifically evaluating the capability of already-existing incineration plants to fulfill the EU needs in the proposed framework. The results of the assessment showed two main crucial issues that could play a pivotal role in the achievement of Circular Economy action plan targets: the need to increase the recycling quotas for specific MSW fractions through the separate collection, and therefore the improvement of definite treatment process chains; the optimization of the recovery of secondary raw materials from incineration bottom ash, involving the Recycling of ferrous and nonferrous metals and the mineral fraction. Both issues need to find an extensive application across all member states to decrease the actual differences in the adoption of sustainable MSW management options.
The main obstacle to bottom ash (BA) being used as a recycling aggregate is the content of salts and potential toxic elements (PTEs), concentrated in a layer that coats BA particles. This work presents a dry treatment for the removal of salts and PTEs from BA particles. Two pilotscale abrasion units (with/without the removal of the fine particles) were fed with different BA samples. The performance of the abrasion tests was assessed through the analyses of particle size and moisture, and that of the column leaching tests at solid-to-liquid ratios between 0.3 and 4.
The results were: the particle-size distribution of the treated materials was homogeneous (25 wt % had dimensions <6.3 mm) and their moisture halved, as well as the electrical conductivity of the leachates. A significant decrease was observed in the leachates of the treated BA for sulphates (44%), chlorides (26%), and PTEs (53% Cr, 60% Cu and 8% Mo). The statistical analysis revealed good correlations between chloride and sulphate concentrations in the leachates with Ba, Cu, Mo, and Sr, illustrating the consistent behavior of the major and minor components of the layer surrounding BA particles. In conclusion, the tested process could be considered as promising for the improvement of BA valorization.
Based on recently published research on leaching control mechanisms in electric arc furnace (EAF) slags, it is assumed that a FeO/SiO2 ratio of around one leads to low leached V and Cr concentrations. This ratio influences the mineral phase composition of the slag toward higher amounts of spinel and a lower solubility of calcium silicate phases by suppressing the formation of magnesiowuestite and highly soluble calcium silicate phases. To evaluate this hypothesis, laboratory and scaled up tests in an EAF pilot plant were performed on slag samples characterized by elevated V and Cr leaching and a high FeO/SiO2 ratio. Prior to the melting experiments, the optimum FeO/SiO2 ratio was calculated via FactSageTM. In the melting experiments, the ratio was adjusted by adding quartz sand, which also decreased the basicity (CaO/SiO2) of the slag. As a reference, remelting experiments without quartz sand addition were conducted and additionally, the influence of the cooling rate of the slag was examined. The remelted (without quartz sand) and the remelted modified slags (with quartz sand) were analyzed chemically and mineralogically and the leaching behavior was investigated. The modification of the slags yielded a minimized release of V and Cr, supporting the hypothesis that the FeO/SiO2 ratio influences the mineralogy and the leaching behavior.
Condensation particle counters (CPCs) are widely used for the measurement of aerosol particle number concentrations in the size range from approximately 3 nm to 3 μm. For an SI-traceable calibration of the size-dependent counting efficiency, which is advisable on a regular basis and required in several applications, Faraday cup aerosol electrometers (FCAEs) are considered to be a suitable SI-traceable reference.While the volumetric aerosol inlet flowrate and the electrical current measurement in FCAEs can be related to respective SI references, inter-comparison exercises for FCAEs are still performed on a regular basis to establish reliable uncertainty budgets and to further investigate the influences of designs and operational parameters on comparability. This is strongly demanded in the international community of metrological institutes and aerosol calibration facilities around the world, which provide CPC calibrations. In the present study, the performance of FCAEs was investigated,using Ag test aerosol particles with a 30 nm particle diameter by varying the inlet flowrates from 0.5 l min−1 to 4 l min−1. From our experimental results, significant deviations were observed in FCAE currents at sample flowrates smaller than 1.5 l min−1. It is recommended that these discrepancies should be quantified before an FCAE is used for CPC calibration at low sample flowrates and small particle sizes in the sub-30 nm size range.
Over the last few years, the Federal Institute for material research (BAM, Berlin) together with the Centre for the Study of Manuscript Cultures (CSMC, University of Hamburg) have initiated a systematic material investigation of black inks produced from Late Antiquity to the Middle Ages (ca. fourth century CE–fourteenth/fifteenth centuries CE), aimed primarily at extending and complementing findings from previous sporadic studies. Part of this systematic investigation has focused on Egyptian Coptic manuscripts, and the present preliminary study is one of its outputs. It centres on a corpus of 45 Coptic manuscripts—43 papyri and 2 ostraca—preserved at the Palau-Ribes and Roca-Puig collections in Barcelona. The manuscripts come from the Monastery of Apa Apollo at Bawit, one of the largest monastic settlements in Egypt between the Late Antiquity and the Early Islamic Period (sixth–eighth centuries CE). The composition of their black inks was investigated in situ using near-infrared reflectography (NIRR) and X-ray fluorescence (XRF). The analyses determined that the manuscripts were written using different types of ink: pure carbon ink; carbon ink containing iron; mixed inks containing carbon, polyphenols and metallic elements; and iron-gall ink. The variety of inks used for the documentary texts seems to reflect the articulate administrative system of the monastery of Bawit. This study reveals that, in contrast to the documents, written mostly with carbon-based inks, literary biblical texts were written with iron-gall ink. The frequent reuse of papyrus paper for certain categories of documents may suggest that carbon-based inks were used for ephemeral manuscripts, since they were easy to erase by abrasion.
Stress is a normal part of life for fungi, which can survive in environments considered inhospitable or hostile for other organisms. Due to the ability of fungi to respond to, survive in, and transform the environment, even under severe stresses, many researchers are exploring the mechanisms that enable fungi to adapt to stress. The International Symposium on Fungal Stress (ISFUS) brings together leading scientists from around the world who research fungal stress. This article discusses presentations given at the third ISFUS, held in Sao Jose dos Campos, Sao Paulo, Brazil in 2019, thereby summarizing the state-of-the-art knowledge on fungal stress, a field that includes microbiology, agriculture, ecology, biotechnology, medicine, and astrobiology.
Currently, corrosion rates (CR) and/or corrosion products (CP) obtained for methanogen-induced microbiologically influenced corrosion (Mi-MIC) on carbon steel are mainly analyzed from static-incubations. By using a multiport-flow-column, much higher CRs (0.72 mm/yr) were observed, indicating static-incubations are not suitable for determining the corrosive potential of Mi-MIC. With the combination of various analytical methods (ToF-SIMS/SEM-EDS/SEM-FIB) and contrary to previously published data, we observed that CPs contained phosphorus, oxygen, magnesium, calcium and iron but lacked carbon-related species (e.g. siderite). Overall, siderite nucleation is disrupted by methanogens, as they convert aqueous bicarbonate into carbon dioxide for methanogenesis resulting in increased localized corrosion.
Currently, sulfate-reducing bacteria (SRB) is regarded as the main culprit of microbiologically influenced corrosion (MIC), mainly due to the low reported corrosion rates of other microorganisms. For example, the highest reported corrosion rate for methanogens is 0.065 mm/yr. However, by investigating methanogen-induced microbiologically influenced corrosion (Mi-MIC) using an in-house developed versatile multiport flow test column, extremely high corrosion rates were observed. We analyzed a large set of carbon steel beads, which were sectionally embedded into the test columns as substrates for iron-utilizing methanogen Methanobacterium IM1. After 14 days of operation using glass beads as fillers for section separation, the highest average corrosion rate of Methanobacterium IM1 was 0.2 mm/yr, which doubled that of Desulfovibrio ferrophilus IS5 and Desulfovibrio alaskensis 16109 investigated at the same conditions. At the most corroded region, nearly 80% of the beads lost 1% of their initial weight (fast-corrosion), resulting in an average corrosion rate of 0.2 mm/yr for Methanobacterium IM1-treated columns. When sand was used as filler material to mimic sediment conditions, average corrosion rates for Methanobacterium IM1 increased to 0.3 mm/yr (maximum 0.52 mm/yr) with over 83% of the beads having corrosion rates above 0.3 mm/yr. Scanning electron images of metal coupons extracted from the column showed methanogenic cells were clustered close to the metal surface. Methanobacterium IM1 is a hydrogenotrophic methanogen with higher affinity to metal than H2. Unlike SRB, Methanobacterium IM1 is not restricted to the availability of sulfate concentration in the environment. Thus, the use of the multiport flow column provided a new insight on the corrosion potential of methanogens, particularly in dynamic conditions, that offers new opportunities for monitoring and development of mitigation strategies. Overall, this study shows under certain conditions methanogenic archaea can cause higher corrosion than SRB, specific quantifications, i.e., maximum, average, and minimum corrosion rates can be determined, and that spatial statistical evaluations of MIC can be carried out.
Flow-back and produced waters from shale gas and shale oil fields contain high ammonium, which can be formed by methanogenic degradation of methylamines into methane and ammonium. Methylamines are added to fracturing fluid to prevent clay swelling or can originate from metabolism of the osmolyte triglycinebetaine (GB).
We analyzed field samples from a shale gas reservoir in the Duvernay Formation and from a shale oil reservoir in the Bakken formation in Canada to determine the origin of high ammonium. Fresh waters used to make fracturing fluid, early flow-back waters, and late flow back waters from the shale gas reservoir had increasing salinity of 0.01, 0.58, and 2.66 Meq of NaCl, respectively. Microbial community analyses reflected this fresh water to saline transition with halophilic taxa including Halomonas, Halanaerobium, and Methanohalophilus being increasingly present. Early and late flow-back waters had high ammonium concentrations of 32 and 15 mM, respectively.
Such high concentrations had also been found in the Bakken produced waters.
Enrichment cultures of Bakken produced waters in medium containing mono, di-, or trimethylamine, or triglycinebetaine (GB) converted these substrates into ammonium (up to 20 mM) and methane. The methylotrophic methanogen Methanohalophilus, which uses methylamines for its energy metabolism and uses GB as an osmolyte, was a dominant community member in these enrichments. Halanaerobium was also a dominant community member that metabolizes GB into trimethylamine, which is then metabolized further by Methanohalophilus. However, the micromolar concentrations of GB measured in shale reservoirs make them an unlikely source for the 1,000-fold higher ammonium concentrations in flow-back waters. This ammonium either originates directly from the reservoir or is formed from methylamines, which originate from the reservoir, or are added during the hydraulic fracturing process. These methylamines are then converted into ammonium and methane by halophilic methylotrophic methanogens, such as Methanohalophilus, present in flow-back waters.
The bipartite interactions between insect hosts and their bacterial gut microbiota, or their bacterial pathogens, are empirically and theoretically well-explored. However, direct, and indirect tripartite interactions will also likely occur inside a host. These interactions will almost certainly affect the trajectory of pathogen virulence evolution, an area that is currently under researched. The interactions within tripartite associations can be competitive, that is, exploitative-competition, interference-competition or apparent-competition. Competitive interactions will be significantly influenced by non-competitive effects, for example, immunopathology, immunosuppression, and microbiota-mediated tolerance. Considering a combination of these interactions and effects, will enable an increased understanding of the evolution of pathogen virulence. This new perspective allows us to identify several novel research questions, which we hope will be a useful framework for future research.
The soil-feeding habit is an evolutionary novelty found in some advanced groups of termites. The study of such groups is important to revealing interesting adaptations to this way-of-life. The genus Verrucositermes is one such example, characterized by peculiar outgrowths on the head capsule, antennae and maxillary palps, which are not found in any other termite. These structures have been hypothesized to be linked to the presence of a new exocrine organ, the rostral gland, whose structure has remained unexplored.
We have thus studied the ultrastructure of the epidermal layer of the head capsule of Verrucositermes tuberosus soldiers.We describe the ultrastructure of the rostral gland, which consists of class 3 secretory cells only. The dominant secretory organelles comprise rough endoplasmic reticulum and Golgi apparatus, which provide secretions delivered to the surface of the head, likely made of peptide-derived components of unclear function. We discuss a possible role of the rostral gland of soldiers as an adaptation to the frequent encounter with soil pathogens during search for new food resources.
The potential release of hazardous substances from polymer-based products is currently in the focus of environmental policy. Environmental simulations are applied to expose such products to selected aging conditions and to investigate release processes. Commonly applied aging exposure types such as solar and UV radiation in combination with water contact, corrosive gases, and soil contact as well as expected general effects on polymers and additional ingredients of polymer-based products are described. The release of substances is based on mass-transfer processes to the material surfaces. Experimental approaches to investigate transport processes that are caused by water contact are presented. For tailoring the tests, relevant aging exposure types and release quantification methods must be combined appropriately. Several studies on the release of hazardous substances such as metals, polyaromatic hydrocarbons, flame retardants, antioxidants, and carbon nanotubes from polymers are summarized exemplarily. Differences between natural and artificial exposure tests are discussed and demonstrated for the release of flame retardants from several polymers and for biocides from paints. Requirements and limitations to apply results from short-term artificial environmental exposure tests to predict long-term environmental behavior of polymers are presented.
Column leaching tests are frequently used and accepted for investigation of release of hazardous substances from solid materials. Independent of differences due to the field of application or national regulations, column tests assume that local equilibrium is established in the experiment which facilitates transfer of results to field conditions. In the process of harmonization and standardization within Europe the question on the influence of flow rate and grain size distribution on the local equilibrium was raised. Thus, a set of experiments using two different masonry materials with varying grain size distribution and flow rate were conducted including stop/flow experiments. Results are compared to a numerical model which takes intraparticle pore diffusion-controlled release of Mo and V into the percolating water into account. Due to the relatively high intraparticle porosity of the materials (24–29%) data and model indicate that initially equilibrium-state conditions prevail followed by rapidly decreasing concentrations. The model fits data for Mo and V reasonably well; however, after the initial decline of concentrations (at L/S > 2) extended tailing is observed especially of elements occurring as oxides, which is not captured by the model.
Construction products are in contact with water (e.g., rain, seepage water) during their service lifetime and may release potentially harmful compounds by leaching processes. Monitoring studies showed that compounds attributed to construction products are found in storm water and the receiving bodies of water and that the release of biocides in urban areas can be comparable to the input of pesticides from agricultural uses. Therefore, a prospective risk assessment of such products is necessary. Laboratory leaching tests have been developed by the Technical Committee CEN/TC 351 and are ready to use. One major task in the future will be the evaluation of the leaching test results, as concentrations found in laboratory experiments are not directly comparable to the field situations. Another Task will be the selection of compounds to be considered for construction products, which are often a complex mixture and contain additives, pigments, stabilization agents, etc. The formulations of the products may serve as a starting point, but total content is a poor predictor for leachability, and analysis of the eluates is necessary. In some cases, nontargeted approaches might be required to identify compounds in the eluates. In the identification process, plausibility checks referring to available information should be included. Ecotoxicological tests are a complementary method to test eluates, and the combined effects of all compounds—including Degradation products—are included. A bio test battery has been applied in a round robin test and was published in a guidance document. Published studies on the ecotoxicity of construction products show the tests’ suitability to distinguish between products with small and larger effects on the environment.
In this work, we use a gas sensor system consisting of a commercially available gas sensor in temperature cycled operation. It is trained with an extensive gas profile for detection and quantification of hazardous volatile organic compounds (VOC) in the ppb range independent of a varying background of other, less harmful VOCs and inorganic interfering gases like humidity or hydrogen. This training was then validated using a different gas mixture generation apparatus at an independent lab providing analytical methods as reference. While the varying background impedes selective detection of benzene and naphthalene at the low concentrations supplied, both formaldehyde and total VOC can well be quantified, after calibration transfer, by models trained with data from one system and evaluated with data from the other system. The lowest achievable root mean squared errors of prediction were 49 ppb for formaldehyde (in a concentration range of 20–200 ppb) and 150 μg/m³ (in a concentration range of 25–450 μg/m³) for total VOC. The latter uncertainty improves to 13 μg/m³ with a more confined model range of 220–320 μg/m³. The data from the second lab indicate an interfering gas which cannot be detected analytically but strongly influences the sensor signal. This demonstrates the need to take into account all sensor relevant gases, like, e.g., hydrogen and carbon monoxide, in analytical reference measurements.
Thermo-Desorption Gas Chromatography-Mass Spectrometry (TD-GC-MS) was used to investigate the thermal degradation of two different polyurethanes (PU). PU samples were heated at different heating rates and the desorbed products were collected in a cold injection system and thereafter submitted to GC-MS. Prospects and limitations of the detection and quantification of semi-volatile degradation products were investigated. A temperature dependent PU depolymerization was
found at temperatures above 200 °C proved by an increasing release of 1,4-butanediol and methylene diphenyl diisocyanate (MDI) representing the main building blocks of both polymers. Their release was monitored quantitatively based on external calibration with authentic compounds. Size Exclusion Chromatography (SEC) of the residues obtained after thermodesorption confirmed the initial competitive degradation mechanism indicating an equilibrium of crosslinking and depolymerization as previously suggested. Matrix-Assisted Laser Desorption Ionization (MALDI) mass spectrometry of SEC fractions of thermally degraded PUs provided additional hints on degradation mechanism.
Equipping ZIF particles with a polyelectrolyte membrane provides functional groups at their interface, enabling further conjugations necessary for applications such as targeted drug delivery. Previous approaches to coat ZIF particles with polyelectrolytes led to surface corrosion of the template material. This work overcomes previous limitations by performing a Layer-by-Layer (LbL) polyelectrolyte coating onto ZIF-8 and ZIF-67 particles in nonaqueous environment. Using the 2-methylimidazolium salt of polystyrensulfonic acid instead of the acid itself and polyethyleneimine in methanol led to intact ZIF particles after polyelectrolyte coating. This was verified by electron microscopy. Further, zetapotential and atomic force microscopy measurements confirmed a continuous polyelectrolyte multilayer built up. The here reported adaption to the well-studied (LbL) polyelectrolyte selfassembly process provides a facile method to equip ZIF particles with a nanometer thin polyelectrolyte multilayer membrane.
While sociality is present in a taxonomically diverse number of species, most animals remain solitary (Bourke, 2011). Over the last centuries, this apparent imbalance in social and non-social animals has led to a great deal of research aimed at shedding light on the biotic and abiotic factors explaining the emergence and maintenance of sociality in nature (West et al., 2015).
Among them, microbes were quickly identified as a major problem for the evolution of social life, because frequent contact between group members typically facilitates the transmission of pathogens, high nest fidelity favours the establishment of microbial pathogens close to their social hosts and, finally, because social groups often exhibit limited genetic diversity and thus limited genetic resistance against certain pathogen strains (Schmid-Hempel, 1998; Cremer et al., 2007). However, this long-standing view has changed considerably over the last few years. Recent research indeed revealed that group living may be more effective than solitary living to Limit the risk of infection by pathogenic microbes because group living also allows the development of an additional layer of defence against pathogens in the form of social immunity (Cremer et al., 2007; Cotter and Kilner, 2010). Under strong pressure from pathogens, microbes could therefore promote, rather than hinder, the evolutionary transition from solitary to group Living (Meunier, 2015; Biedermann and Rohlfs, 2017). Moreover, we are increasingly aware that many microbes provide essential benefits to their hosts by performing critical digestive, physiological, and reproductive functions (Engel and Moran, 2013; McFall-Ngai et al., 2013). The need to Access beneficial microbes may thus have played a role in the expression of frequent and tight interactions between conspecifics and ultimately promoted social evolution (Wilson, 1971; Onchuru et al., 2018). Finally, a growing number of studies suggest that microbes could enforce the Aggregation and expression of cooperative behaviours of the hosts to increase their chance of reaching new hosts and may therefore be involved in the evolution of host sociality (Lewin-Epstein et al., 2017) (but see Johnson and Foster, 2018).
Almost 500 municipal solid waste incineration plants in the EU, Norway and Switzerland generate about 17.6 Mt/a of incinerator bottom ash (IBA). IBA contains minerals and metals. Metals are mostly separated and sold to the scrap market and minerals are either disposed of in landfills or utilised in the construction sector. Since there is no uniform regulation for IBA utilisation at EU level, countries developed own rules with varying requirements for utilisation. As a result from a cooperation network between European experts an up-to-date overview of documents regulating IBA utilisation is presented. Furthermore, this work highlights the different requirements that have to be considered. Overall, 51 different parameters for the total content and 36 different parameters for the emission by leaching are defined. An analysis of the defined parameter reveals that leaching parameters are significantly more to be considered compared to total content parameters. In order to assess the leaching behaviour nine different leaching tests, including batch tests, up-flow percolation tests and one diffusion test (monolithic materials) are in place.
A further discussion of leaching parameters showed that certain countries took over limit values initially defined for landfills for inert waste and adopted them for IBA utilisation. The overall utilisation rate of IBA in construction works is approximately 54 wt%. It is revealed that the rate of utilisation does not necessarily depend on how well regulated IBA utilisation is, but rather seems to be a result of political commitment for IBA recycling and economically interesting circumstances.
Tempeh is a common food in Indonesia, produced by fungal fermentation of soybeans using Rhizopus sp., as well as Aspergillus oryzae, for inoculation. Analogously, for economic reasons, mixtures of maize and soybeans are used for the production of so-called tempeh-like products. For maize, a contamination with the mycoestrogen zearalenone (ZEN) has been frequently reported. ZEN is a mycotoxin which is known to be metabolized by Rhizopus and Aspergillus species. Consequently, this study focused on the ZEN transformation during tempeh fermentation. Five fungal strains of the genera Rhizopus and Aspergillus, isolated from fresh Indonesian tempeh and authentic Indonesian inocula, were utilized for tempeh manufacturing from a maize/soybean mixture (30:70) at laboratory-scale. Furthermore, comparable tempeh-like products obtained from Indonesian markets were analyzed. Results from the HPLC-MS/MS analyses show that ZEN is intensely transformed into its metabolites alpha-zearalenol (alpha-ZEL), ZEN-14-sulfate, alpha-ZEL-sulfate, ZEN-14-glucoside, and ZEN-16-glucoside in tempeh production. alpha-ZEL, being significantly more toxic than ZEN, was the main metabolite in most of the Rhizopus incubations, while in Aspergillus oryzae fermentations ZEN-14-sulfate was predominantly formed. Additionally, two of the 14 authentic samples were contaminated with ZEN, alpha-ZEL and ZEN-14-sulfate, and in two further samples, ZEN and alpha-ZEL, were determined. Consequently, tempeh fermentation of ZEN-contaminated maize/soybean mixture may lead to toxification of the food item by formation of the reductive ZEN metabolite, alpha-ZEL, under model as well as authentic conditions.