4 Material und Umwelt
Filtern
Dokumenttyp
Sprache
- Englisch (23) (entfernen)
Schlagworte
- Leaching (23) (entfernen)
Organisationseinheit der BAM
- 4 Material und Umwelt (23) (entfernen)
Paper des Monats
- ja (2)
Eingeladener Vortrag
- nein (4)
The potential release of hazardous substances from polymer-based products is currently in the focus of environmental policy. Environmental simulations are applied to expose such products to selected aging conditions and to investigate release processes. Commonly applied aging exposure types such as solar and UV radiation in combination with water contact, corrosive gases, and soil contact as well as expected general effects on polymers and additional ingredients of polymer-based products are described. The release of substances is based on mass-transfer processes to the material surfaces. Experimental approaches to investigate transport processes that are caused by water contact are presented. For tailoring the tests, relevant aging exposure types and release quantification methods must be combined appropriately. Several studies on the release of hazardous substances such as metals, polyaromatic hydrocarbons, flame retardants, antioxidants, and carbon nanotubes from polymers are summarized exemplarily. Differences between natural and artificial exposure tests are discussed and demonstrated for the release of flame retardants from several polymers and for biocides from paints. Requirements and limitations to apply results from short-term artificial environmental exposure tests to predict long-term environmental behavior of polymers are presented.
The leaching behavior of scandium (Sc) from bauxite residues can differ significantly when residues of different geological backgrounds are compared. The mineralogy of the source rock and the physicochemical environment during bauxitization affect the association of Sc in the bauxite i.e., how Sc is distributed amongst different mineral phases and whether it is incorporated in and/or adsorbed onto those phases. The Sc association in the bauxite is in turn crucial for the resulting Sc association in the bauxite residue. In this study systematic leaching experiments were performed on three different bauxite residues using a statistical design of experiments approach. The three bauxite residues compared originated from processing of lateritic and karstic bauxites from
Germany, Hungary, and Russia. The recovery of Sc and Fe was determined by ICP-OES measurements. Mineralogical changes were analyzed by X-ray-diffraction and subsequent Rietveld refinement. The effects of various parameters including temperature, acid type, acid concentration, liquid-to-solid ratio and residence time were studied. A response surface model was calculated for the selected case of citric acid leaching of Hungarian bauxite residue. The investigations showed that the type of bauxite residue has a strong influence. The easily leachable fraction of Sc can vary considerably between the types, reaching ~20–25% in German Bauxite residue and ~50% in Russian bauxite residue. Mineralogical investigations revealed that a major part of this fraction was released from secondary phases such as cancrinite and katoite formed during Bayer processing of the bauxite.
The effect of temperature on Sc and Fe recovery is strong especially when citric acid is used. Based on the exponential relationship between temperature and Fe-recovery it was found to be particularly important for the selectivity of Sc over Fe. Optimization of the model for a maximum Sc recovery combined with a minimum Fe
recovery yielded results of ~28% Sc recovery at <2% Fe recovery at a temperature of 60 ◦C, a citric acid normality of 1.8, and a liquid-to-solid ratio of 16 ml/g. Our study has shown that detailed knowledge about the Sc association and distribution in bauxite and bauxite residue is key to an efficient and selective leaching of Sc
from bauxite residues.
Tools for the characterization of secondary raw materials - status of leaching test application
(2018)
Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed.
Tools for the characterization of secondary raw materials - status of leaching test application
(2018)
Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed.
Chemical modification of wood applying benzotriazolyl-activated carboxylic acids has proven to be a versatile method for the durable functionalization of its lignocellulosic biopolymers. Through this process, the material properties of Wood can be influenced and specifically optimized. To check the scope and limitations of this modification method, various benzamide derivatives with electron-withdrawing (EWG) or electron-donating (EDG) functional groups in different positions of the aromatic ring were synthesized and applied for covalent modification of Scots pine (Pinus sylvestris L.) sapwood in this study. The bonded amounts of substances (up to 2.20 mmol) were compared with the reactivity constants of the Hammett equation, revealing a significant correlation between the modification efficiency and the theoretical reactivity constants of the corresponding aromatic substitution pattern. The successful covalent attachment of the respective substituted benzamides was proven by attenuated total reflection infrared (ATR-IR) spectroscopy, while the stability of the newly formed ester bond was proven in a standardized leaching test.
Release of substances from joint grouts based on various binder types and their ecotoxic effects
(2022)
Background: The leaching of substances and the ecotoxic effects of eluates were studied for joint grouts that are based on various types of binders. Eight products, two of them containing either epoxy resin, polybutadiene or polyurethane binders, or modifed cement, were investigated using harmonized leaching tests for construction products in combination with ecotoxicity tests on algae, daphnia, luminescent bacteria, fish eggs and mutagenicity in accordance with CEN/TR 17105. In addition to basic parameters, such as pH, TOC, and inorganic components, organic substances in the eluates were analysed by gas and liquid chromatography in combination with mass spectrometry. Quantitative analyses in combination with ecotoxicity data on selected substances were used to deduce which substances cause the observed ecotoxic effects.
Results: Different patterns of ecotoxic effects were observed in joint grouts with different binder types. The most ecotoxic effects were observed in epoxy resin-based products, followed by polybutadiene-based products. Fewer ecotoxic effects were observed in polyurethane-based products and modifed cements. Some of these showed no ecotoxicity. Some of the substances in the eluates were identified and related to ecotoxic effects. 4-Tert-butylphenol and amines probably contributed to the ecotoxic effects of at least one of the epoxy resin-based renders, whereas cobalt is assumed to contribute to the toxic effect on algae of one of the polybutadiene-based products. However, only some of the leached substances could be identifed, and only some of the ecotoxic effects can be explained by the available information on the composition of eluates and known ecotoxic profiles of the identified substances.
Conclusions: Ecotoxicity tests on eluates from leaching tests indicate whether environmentally hazardous substances can be leached from construction products. Combined ecotoxicity tests and chemical analysis of eluates from EU-wide harmonized leaching tests for construction products can provide information on substances that cause these effects. This supports the identifcation and development of environmentally friendly construction products.
This study confirmed that ecotoxicity tests in accordance with CEN/TR 17105 are a tool well-suited to support the implementation of the European Commission’s zero pollution vision for 2050 and to reduce pollution to levels no longer considered harmful to health and natural ecosystems.
Potential use of incineration bottom ash in construction – Evaluation of the environmental impact
(2020)
Knowledge of the long-term leaching behavior of potentially harmful substances is crucial for the assessment of the environmental compatibility of reusing municipal solid-waste incineration bottom ash (MSWI BA) in construction, i.e., as a road base layer.
BA fractions obtained from wet-processing aiming at the improvement of environmental quality were used to investigate the mobility of relevant substances. Eluates from laboratory-scaled leaching procedures (column percolation and lysimeters) were analyzed to learn about the long-term release of substances. Unsaturated conditions and artificial rainwater (AR) were used in the lysimeter tests to simulate field conditions. In addition, batch test eluates were generated at usual liquid-to-solid ratios (L/S) for compliance testing purposes. A variety of cations and anions was measured in the eluates.
The wet treatment reduces the leaching of chloride and particularly sulfate by more than 60%. The release of typical contaminants for the treated MSWI BA such as the heavy metals Cu and Cr was well below 1% in the conducted leaching tests.
An increase in the Sb concentration observed in the lysimeter experiments starting at L/S 0.75 L/kg and in the column experiment at L/S 4 L/kg is assumed to be related to decreasing concentrations of Ca and thus to the dissolution of sparingly soluble calcium antimonate. The same leaching mechanism applies with V, but the concentration levels observed are less critical regarding relevant limit values. However, on the long term the behavior of Sb could be problematic for the application of MSWI BA in construction.
Potential use of incineration bottom ash in construction – Evaluation of environmental impact
(2018)
Around 5 million tonnes of MSWI bottom ash (BA) are generated per year in Germany. The incineration itself serves for metals as a concentrating and cleaning process. However, due to the almost exclusive wet extraction out of the furnace chamber the various metals are integrated in a heterogeneous and instable matrix. The metal recovery is therefore still a challenge relating the recovery rate and the purity, respectively. With state of the art treatment trains in Germany around 7.7% of ferrous metals and 1.3% of non-ferrous metals can be recovered out of MSWI BA. Large quantities of the mineral fraction are reused for sub-base material in road construction. A three month ageing period has been established as the common practice of further treatment of bottom ash before reuse applications. In the course of this aging the pH value of bottom ash decreases and contaminants are immobilized by processes like carbonation, hydration and oxidation. In particular leaching of heavy metals may be reduced to environmentally acceptable levels. However, the aging results in fixing of other valuable resources such as metals. Two laboratory scale lysimeters (30 cm in diameter) are being operated for more than three years aiming at the investigation of the long-term leaching behavior of a 0.25/45 mm mineral material obtained by treatment of MSWI bottom ash directly after incineration by a wet processing technology. Artificial rainwater is used as leachant (pH ≈ 6, ingredients NO32-, Cl-, SO42-, Na+, K+, Ca2+, Mg2+). The lysimeters are irrigated related to an average annual precipitation rate of 600 mm/a leading to a liquid to solid ratio (L/S) of about 0.7 per year of operation. Lysimeter tests are more adequate to simulate field scenarios and long-term leaching behavior in contrast to laboratory column tests particularly due to the unsaturated conditions and realistic contact time with the leachant.
In comparison to the leaching of bottom ash (aged for 3 month and non-treated) in column tests the chloride and sulfate leaching in the lysimeters was reduced as a consequence of the previous wet processing. The sulfate release kept almost constant limited by CaSO4 solubility up to an L/S of about 0.7 l/kg. The chloride concentrations dropped quickly, starting from 7300 mg/l, and are now at an almost constant level of 50 mg/l which is significantly above the chloride concentration in the leachant. After an initial decrease of the pH from about 10.4 to 8 at L/S of 0.2 l/kg, the pH increased again and leveled out around 9.8 up to L/S 2.2 l/kg. At an L/S of about 2.5 l/kg now, Cr, Cu are still released. The Cu and Cr concentrations in the leachates were about 760 µg/l and 90 µg/l respectively at the beginning. For both metals the concentration decreased to about 35 µg/l now. The Mo concentrations dropped steadily from 1300 to 250 µg/l, whereas V and Sb concentrations increased in the course of the tests. Fe and Mn are not detectable anymore. More results of this experimental study will be presented and discussed with a special focus on elements forming oxyanions.
This Special Issue, ‘Measurement of the Environmental Impact of Materials’, is focused on the impact that materials have on the environmental compartments of soil, water and air. Leaching and emission processes, including underlying mechanisms, are a recurring topic in most published articles in the present Special Issue. Contributions have come from three continents and numerous countries (USA, Germany, France, Latvia, Poland, Russia, Japan, Korea and Thailand) indicating the global dimension of the subject.