2.1 Sicherheit von Energieträgern
Filtern
Dokumenttyp
- Vortrag (187)
- Zeitschriftenartikel (88)
- Beitrag zu einem Tagungsband (41)
- Posterpräsentation (23)
- Sonstiges (4)
- Forschungsbericht (4)
- Buchkapitel (1)
- Beitrag zu einem Sammelband (1)
- Dissertation (1)
- Handbuch (1)
Schlagworte
- Explosionsschutz (36)
- Schlagfunken (29)
- Mechanisch erzeugte Funken (26)
- Nichtelektrischer Explosionsschutz (25)
- Nichtelektrische Funken (23)
- Behälterversagen (19)
- Reibfunken (19)
- Safety (19)
- Schleiffunken (19)
- Hydrogen (16)
Organisationseinheit der BAM
- 2 Prozess- und Anlagensicherheit (351)
- 2.1 Sicherheit von Energieträgern (351)
- 8 Zerstörungsfreie Prüfung (34)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (30)
- 3 Gefahrgutumschließungen; Energiespeicher (22)
- 9 Komponentensicherheit (22)
- 9.6 Additive Fertigung metallischer Komponenten (14)
- 7 Bauwerkssicherheit (10)
- 8.4 Akustische und elektromagnetische Verfahren (10)
- 3.5 Sicherheit von Gasspeichern (9)
Paper des Monats
- ja (3)
Im Rahmen Rahmen des BMBF-Vorhabens SEE-2L wurde auf dem Testgelände Technische Sicherheit (BAM TTS) ein Großversuchsstand für das thermische Durchgehen von Lithium-Batterien auf Modul- und Batterieebene entwickelt und aufgebaut. Im Zuge des Projektes konnte eine erste Versuchsserie zu den Auswirkungen des thermischen Durchgehens von Batteriemodulen durchgeführt werden. Im Vortrag werden die wesentlichen Ergebnisse der Versuche vorgestellt.
Der Abschlussbericht stellt die wesentlichen Arbeitsschritte und Ergebnisse des Teilvorhabens der BAM im BMBF-Vorhaben SEE-2L vor. Im Rahmen dieses Vorhabens wurde auf dem Testgelände Technische Sicherheit (BAM TTS) ein Großversuchsstand für das thermische Durchgehen von Lithium-Batterien auf Modul- und Batterieebene entwickelt und aufgebaut. Im Zuge des Projektes konnte eine erste Versuchsserie zu den Auswirkungen des thermischen Durchgehens von Batteriemodulen durchgeführt werden. Der Abschlussbericht umfasst zwei Teile, im Teil I den Kurzbricht und im Teil II die eingehende Darstellung.
Blast injuries are among the most common injuries in military operations. Also, in civilian environments, more explosive threats are expected in the future due to emerging conflicts and threats. While the effect of fragments, which is classified as secondary blast injury, could be minimized by police and military personnel’s modern ballistic body protection systems, the effects of shock wave propagation in the body as part of the primary explosion trauma still remain a serious threat needing further research.
The detonation-physical processes of highly dynamic pressure changes within the human body, the reflection-related amplification of shock waves at organ-dermis interfaces, and the consequences of injury mechanisms have become more prominent in international research. Various approaches have been used to investigate these aspects. Animal experiments on free field test sites or shock tube setups combined with a subsequent biological evaluation and numerical simulations provided promising results and allowed the discussion of different biomechanical aspects. However, due to poor reproducibility and a lack of short-term dynamic material properties, most research approaches have significant limitations. Laboratory test setups do not represent real-scale high explosive detonation parameters with regards to pressure characteristics, impulse duration and blockage problems. Measured values are interpreted with partly outdated, selective and not validated limit values for overpressures from field tests with animals. This is due to the lack of a validated and comprehensive data set covering a variation of the crucial parameter. Injury mechanisms and their effects have not yet been sufficiently elucidated for the torso and extremities.
In order to contribute to the research efforts on the primary explosion effects, the German Federal Armed Forces established an interdisciplinary military medical research project in cooperation of the Bundeswehr Hospital Berlin and the German Federal Institute for Materials Research and Testing (BAM). The aim of the planned investigation is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times.
Following directly from the information presented at IFBIC 2023 on the research project 'Investigation of intracorporeal shock wave propagation using a simplified torso model and a shock wave generator', the latest results are presented below [1]. In order to contribute to the research efforts on the primary explosion effects, the aim of the investigation is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental series with short set-up times.
To achieve this, an autoclave with a volume of 0.065 m3 is used to generate reproducible pressure waves (Fig. 1). The autoclave will be referred to as Shockwave Generator (SWG). The pressure wave is produced by the detonation of a stoichiometric mixture of acetylene and oxygen under atmospheric conditions. The SWG-outlet is sealed by a rupture disc, which can be adjusted in thickness to vary the initial pressure. Additionally, modifying the composition of the acetylene-oxygen mixture can result in different load cases. The SWG requires approximately 30 minutes of set-up time between trials. The SWG was adjusted to match the characteristics of a real and typical explosive through free-field measurements. The experiments demonstrated that the pressure wave propagates in a hemispherical shape and has sufficient reproducibility.
To represent soft tissue, a basic model made of homogeneous ballistic gelatin is used in a geometrically simplified torso model (STM) (Fig. 2). The STM was enlarged to outer dimensions of 400 x 250 x 240 mm. Viscoelastic behavior of the ballistic gelatin can be assumed due to the collagen structure [2]. The density of the ballistic gelatin, and therefore the sound velocity, can be adjusted by changing the mixing ratio. Simplified simulants, such as hollow and solid material (bone simulant), were embedded in the STM. Additionally, the STM has been tested as a carrier material for biological substances, such as indicator species. The next step is to test the STM as a carrier material for larger organic tissue structures such as lungs or kidneys. The organic tissue samples will undergo histological examination to analyze their structural changes afterwards. The STM is equipped with embedded piezoelectric pressure sensors, an accelerometer and a temperature sensor. Visual documentation is captured using a high-speed camera. This measurement setup allows for the tracking of the coupled pressure wave and its behavior within the model and at the media transitions. Pressure values can be recorded after certain media changes, such as from soft tissue to a solid material (Figure 3).
The following is a review of the optimizations made to the entire experimental setup. The reproducibility of the SWG was increased. This was achieved by extending the evacuation process to the entire feed system of the SWG. Nitrogen residues in the SWG system can thus be avoided. As a result, the double peaks that occur at the first maximum can be avoided, as combustion runs more evenly without the nitrogen residues. In addition, partially varying peak overpressures can be avoided, as the acytelene-oxygen mixture is not too lean due to the elimination of the nitrogen residues. The workflow has been streamlined, resulting in an average set-up time of 25 minutes for the SWG. In the case of the STM, the manufacturing process in particular was optimized by examining and defining the manufacturing process based on scientific publications, which increases the reproducibility of the STM base bodies. As already mentioned in the previous paragraph, the STM was equipped with various additives in order to investigate the transition behavior of the pressure wave.
The following trail serves as an example: A comparison is made between the STM in the basic structure (Fig. 2 l.s.) and with an embedded solid material (bone plate) (Fig. 3 l.s.). An external overpressure of 100 kPa is generated by the SWG at a distance of 1 m, where the STM is placed. For the basic STM structure, the sensor distance is consistently 100 mm. The internal overpressure is visible in Fig. 2 r.s.. A typical ideal pressure curve can be seen. The characteristic points are easily distinguishable from the reflection peaks. In the STM with an embedded solid material, the sensor distance remains consistently at 66.6 mm
Die Transformation der Energienutzung von konventionellen zu erneuerbaren Quellen führt dazu, dass zukünftig mehr Energie effizient zwischengespeichert werden muss. Eine Möglichkeit der elektrochemischen Zwischenspeicherung bieten Lithium-Ionen-Batterien. Hierfür können ausgemusterte Automobilantriebsbatterien verwendet werden. Erfüllen sie die hohen Anforderungen des mobilen Bereichs nicht mehr, haben sie oftmals noch eine ausreichende Kapazität und Leistungsfähigkeit für die stationäre Zwischenspeicherung.
Neben der Verwendung der Batterien im größeren Maßstab, z.B. bei Energieversorgern, werden durch den vermehrten Einsatz von Photovoltaik-Anlagen in Ein- und Mehrfamilienhäusern verstärkt Zwischenspeicher für Privathaushalte nachgefragt. Dies birgt auch für Einsatzkräfte neue Herausforderungen in der Gefahrenabwehr.
Im vom Bundesministerium für Bildung und Forschung (BMBF) geförderten Verbundprojekt „SEE-2L – Sicherheit elektrochemischer Energiespeicher in Second Life Anwendungen“ wurden Versuche mit Second Life Modulen durchgeführt. Verbundpartner im Projekt waren neben der vfdb die Otto-von-Guericke-Universität Magdeburg und die Bundesanstalt für Materialforschung und -prüfung. Zudem war das Institut der Feuerwehr Nordrhein-Westfalen eingebunden.
Die durchgeführten Versuche bilden eine Grundlage für die Einordnung der Batteriespeicher, z.B. aus Sicht des baulichen Brandschutzes, zur Methodik der Brandbekämpfung oder zur Risikobewertung hinsichtlich der Prozess- und Anlagensicherheit.
Im Beitrag werden die Versuchsergebnisse vorgestellt und Ansätze für deren Anwendung gezeigt. Um die gewonnenen Erkenntnisse zu vermitteln, wurde im Projekt zudem ein Schulungskonzept für Einsätze mit Lithium-Ionen-Technologien erarbeitet, das im Beitrag präsentiert wird. Es besteht aus theoretischen und praktischen Anteilen, sodass bei den Feuerwehren praxisnah aus- bzw. fortgebildet werden kann.
The introduction of hydrogen as a safe energy carrier needs a robust knowledge base, tools for the design and safety assessment of hydrogen technologies built on it, and an internationally harmonized set of standards and regulations. Many of the innovative technologies imply hydrogen at high pressures and/or cryogenic temperatures, with which private users come into contact for the first time in distributed applications. In order to avoid over-conservative, expensive safety solutions, while at the same time demonstrating the usability and safety of hydrogen applications and maintaining acceptance for the technology, safety research must also keep pace with, or better yet anticipate, trends in technological development. Thus, this overview article describes not only the current state of knowledge and technology regarding hydrogen safety, but also its further development.
Im Rahmen des Vortrags wurden die Ergebnisse und die Methodik zur Erhebung von Forschungsbedarfen und Fähigkeitslücken bei den Behörden und Organisationen mit Sicherheitsaufgaben, welche im Rahmen des Projektes InnoBOSK durchgeführt wurden, vorgestellt. Den Schwerpunkt bildete dabei die Umsetzung der Workshops gemeinsam mit den Einsatzkräften und die Umsetzung der problemorientierten Erhebungsmethodik.
Sicherheitstechnische Untersuchungen von Wasserstoff Freistrahlflammen bei Hochdruck im Realmaßstab
(2024)
Wasserstoff als Energieträger gewinnt zunehmend an Bedeutung. Die Untersuchung von Störfallauswirkungen mit Wasserstoff rückt somit stärker in den Fokus. Da Wasserstoff meist unter Druck gelagert und transportiert wird, ist ein zu betrachtendes Szenario die Freisetzung aus einer Leckage mit anschließender Zündung. Die daraus resultierende Freistrahlflamme (Jet Flame) muss hinsichtlich der in die Umgebung emittierten Wärmestrahlung charakterisiert werden. In der Literatur existieren bereits verschiedene Modelle, welche jedoch vermehrt auf Daten aus Kohlenwasserstoffflammen mit geringem Impuls basieren. Zur Überprüfung dieser Modelle wird im Zuge des BAM internen H2 Jet Flame Projektes die sicherheitstechnische Untersuchung von impulsbehafteten Wasserstoff Freistrahlflammen vorgenommen. Hierfür finden Versuche im Realmaßstab auf dem Testgelände Technische Sicherheit der BAM (BAM-TTS) statt. Gegenstand der Untersuchungen ist die Beurteilung der Auswirkungen von realistischen Freisetzungsszenarien hinsichtlich der Flammengeometrie und der freigesetzten Wärmestrahlung. Dabei werden Parameter wie Freisetzungswinkel, Leckagedurchmesser (z.Zt. 1 mm bis 30 mm), Druck (z.Zt. bis max. 250 bar) und Massenstrom (bis max. 0,5 kg/s) variiert. Zusätzlich können auch Einflüsse wie Art der Zündung, Zündort sowie Zündung mit zeitlichem Verzug untersucht werden. Gewonnene Erkenntnisse werden mit den Ergebnissen bereits vorhandener Modelle verglichen und diese im Bedarfsfall weiterentwickelt. Insbesondere wird der Fokus auf die Modellierung der freigesetzten Wärmestrahlung von Wasserstoffflammen gelegt. Herausforderung dabei stellt die IR-Vermessung und Modellierung von Sichtmodellen der Flammen dar. Die Visualisierung der Flammengeometrie wird mit Hilfe mehrerer Infrarot Kamerasystemen (aus mindestens zwei Blickwinkeln) vorgenommen.
Bisherige Messungen, die in der Literatur zu finden sind, basieren meist auf instationären Auströmbedingungen. Der hier verwendete Versuchsaufbau ermöglicht ein stationäres Ausströmen für mehrere Minuten und somit eine direkte Vergleichbarkeit mit den existierenden (stationären) Modellen.
Weiterhin ist der Versuchsstand umrüstbar für Vergleichsmessungen mit Kohlenwasserstoffen (Methan etc.) sowie Mischungen aus Wasserstoff und Kohlenwasserstoffen.
In order to reduce the human footprint of CO2 emissions and limit global warming effects hydrogen combustion is becoming increasingly important. To enable fuel cells and gas turbines to operates this carbon free fuel, unprecedently large amounts of hydrogen need to be produced and safely transported and stored. The investigation of the effects of accidents involving hydrogen is therefore becoming of outmost importance. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety regulations. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames.[1-4] To verify these models, a H2 Jet Flame project conducted at BAM, is investigating the safety of momentum driven hydrogen jet flames. For this purpose, large-scale tests are carried out at the Test Site Technical Safety (BAM-TTS). The object of the investigations is to assess the effects of real scale release scenarios regarding flame geometry and the thermal radiation emitted. Parameters such as release angle, leakage diameter (currently 1 mm to 10 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In addition, influences such as the type of ignition, ignition location as well as delayed ignition can also be investigated. The gained knowledge will be compared with existing jet flame models, to validate these and identify a possible need for further development. In particular, the focus will be laid on the thermal radiation of hydrogen flames. The challenge here is the visualization and characterization of the flame geometry in an open environment. Visualization is performed using infrared (IR) camera systems from at least two viewing angles. Measurements of the heat radiation of jet flames, which can be found in the literature, are mostly based on unsteady outflow conditions.The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, the tests can be carried out for comparative measurements with hydrocarbons (methane, etc.) as well as mixtures of hydrogen and hydrocarbons.
Sicherheitstechnische Untersuchungen von Wasserstoff Freistrahlflammen bei Hochdruck im Realmaßstab
(2024)
Wasserstoff als Energieträger gewinnt zunehmend an Bedeutung. Die Untersuchung von Störfallauswirkungen mit Wasserstoff rückt somit stärker in den Fokus. Da Wasserstoff meist unter Druck gelagert und transportiert wird, ist ein zu betrachtendes Szenario die Freisetzung aus einer Leckage mit anschließender Zündung. Die daraus resultierende Freistrahlflamme (Jet Flame) muss hinsichtlich der in die Umgebung emittierten Wärmestrahlung charakterisiert werden. In der Literatur existieren bereits verschiedene Modelle, welche jedoch vermehrt auf Daten aus Kohlenwasserstoffflammen mit geringem Impuls basieren. Zur Überprüfung dieser Modelle wird im Zuge des BAM internen H2 Jet Flame Projektes die sicherheitstechnische Untersuchung von impulsbehafteten Wasserstoff Freistrahlflammen vorgenommen. Hierfür finden Versuche im Realmaßstab auf dem Testgelände Technische Sicherheit der BAM (BAM-TTS) statt. Gegenstand der Untersuchungen ist die Beurteilung der Auswirkungen von realistischen Freisetzungsszenarien hinsichtlich der Flammengeometrie und der freigesetzten Wärmestrahlung. Dabei werden Parameter wie Freisetzungswinkel, Leckagedurchmesser (z.Zt. 1 mm bis 10 mm), Druck (z.Zt. bis max. 250 bar) und Massenstrom (bis max. 0,5 kg/s) variiert. Zusätzlich können auch Einflüsse wie Art der Zündung, Zündort sowie Zündung mit zeitlichem Verzug untersucht werden. Gewonnene Erkenntnisse werden mit den Ergebnissen bereits vorhandener Modelle verglichen und diese im Bedarfsfall weiterentwickelt. Insbesondere wird der Fokus auf die Modellierung der freigesetzten Wärmestrahlung von Wasserstoffflammen gelegt. Herausforderung dabei stellt die IR-Vermessung und Modellierung von Sichtmodellen der Flammen dar. Die Visualisierung der Flammengeometrie wird mit Hilfe mehrerer Infrarot Kamerasystemen (aus mindestens zwei Blickwinkeln) vorgenommen.
Bisherige Messungen, die in der Literatur zu finden sind, basieren meist auf instationären Auströmbedingungen. Der hier verwendete Versuchsaufbau ermöglicht ein stationäres Ausströmen für mehrere Minuten und somit eine direkte Vergleichbarkeit mit den existierenden (stationären) Modellen.
Weiterhin ist der Versuchsstand umrüstbar für Vergleichsmessungen mit Kohlenwasserstoffen (Methan etc.) sowie Mischungen aus Wasserstoff und Kohlenwasserstoffen.
In order to reduce the human footprint of CO2 emissions and limit global warming effects hydrogen combustion is becoming increasingly important. To enable fuel cells and gas turbines to operates this carbon free fuel, unprecedently large amounts of hydrogen need to be produced and safely transported and stored. The investigation of the effects of accidents involving hydrogen is therefore becoming of outmost importance. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety regulations. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames.[1-4] To verify these models, a H2 Jet Flame project conducted at BAM, is investigating the safety of momentum driven hydrogen jet flames. For this purpose, large-scale tests are carried out at the Test Site Technical Safety (BAM-TTS). The object of the investigations is to assess the effects of real scale release scenarios regarding flame geometry and the thermal radiation emitted. Parameters such as release angle, leakage diameter (currently 1 mm to 10 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In addition, influences such as the type of ignition, ignition location as well as delayed ignition can also be investigated. The gained knowledge will be compared with existing jet flame models, to validate these and identify a possible need for further development. In particular, the focus will be laid on the thermal radiation of hydrogen flames. The challenge here is the visualization and characterization of the flame geometry in an open environment. Visualization is performed using infrared (IR) camera systems from at least two viewing angles. Measurements of the heat radiation of jet flames, which can be found in the literature, are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, the tests can be carried out for comparative measurements with hydrocarbons (methane, etc.) as well as mixtures of hydrogen and hydrocarbons.
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein und stellt Prüfverfahren vor. Aus den Ergebnissen durchgeführter Untersuchungen werden Empfehlungen für sicheren Transport und Lagerung abgeleitet.
In einer Reihe von Experimenten wurden die möglichen Folgen der Freisetzung von verflüssigtem Wasserstoff (LH2) auf, bzw. unter Wasser untersucht. Die Experimente zielten darauf ab, eine unbeabsichtigte Freisetzung von LH2 (z.B. durch Schlauchabriss) insbesondere bei der Betankung eines Schiffes zu simulieren. Für verflüssigtes Erdgas (LNG) wurden dabei sog. RPT’s (rapid phase transition) nachgewiesen, bei denen die spontane Verdampfung relevante Druckwellen erzeugt. Es kann nicht ausgeschlossen werden, dass RPTs auch im Falle von LH2 möglich sind. Die Versuche wurden auf dem Testareal Wasserstoffsicherheit auf dem Testgelände Technische Sicherheit der Bundesanstalt für Materialforschung und -prüfung (BAM-TTS) in Horstwalde, im Rahmen einer Forschungskooperation zwischen der BAM und Gexcon im Rahmen des SH2IFT-Programms durchgeführt. Die LH2-Freisetzungen erfolgten direkt aus einem LH2-Tanklastwagen über eine lange, flexible, vakuumisolierte Transferleitung. Während die Freisetzung oberhalb und unterhalb der Wasseroberfläche jeweils vertikal orientiert war, wurde bei der Unterwasserfreisetzung zusätzlich eine horizontale Ausströmung, parallel zur Wasseroberfläche realisiert. Zur Bestimmung des Massenstromes, wurde ein Wägesystem unter dem Tankwagen eingesetzt. Spezielle Drucksensoren wurden verwendet, um die durch die Freisetzungsvorgänge erzeugten Stoßwellen sowohl im Wasser als auch in der Luft zu messen. Die Gaskonzentrationen über dem Wasserbecken wurden an verschiedenen Positionen gemessen. Hochgeschwindigkeits-, Infrarot- (IR) und normale Kameras wurden eingesetzt, um die Phänomenologie der Freisetzung aufzuzeichnen und das Verhalten der Gaswolke im Zeitverlauf zu verfolgen. Neben den fest installierten Systemen an Land, kamen auch Unterwasserkameras sowie eine Drohne mit Normal- und IR-Kameras zum Einsatz. Zwei Wetterstationen wurden zur Messung von Windgeschwindigkeit, Windrichtung, Temperatur und Luftfeuchtigkeit während aller durchgeführten Tests eingesetzt. Des Weiteren kamen Bolometer zur Wärmestrahlungsmessung zum Einsatz. Zwar führten die Freisetzung zu einer hochturbulenten LH2/Wasser Mischzone, jedoch zu keinen nennenswerten Überdrücken durch RPT. Im Gegensatz dazu wurde unerwartet, aber reproduzierbar, eine Zündung der Gaswolke in freier Luft in einiger Entfernung von den Instrumenten und dem Ort der Freisetzung beobachtet. Die daraus resultierenden Gaswolkenexplosionen führten zu relevanten Überdrücken und zur Wärmeabstrahlung in die Umgebung.
In einer Versuchsreihe im Realmaßstab wurden drei Flüssigwasserstofftanks (LH2) unterfeuert. Hierbei sollte unter anderem geklärt werden, ob es, analog zu druckverflüssigten Gasen, zu einem BLEVE (Boiling Liquid Expanding Vapor Cloud Explosion) kommen kann. Die Experimente wurden auf dem Testareal Wasserstoffsicherheit des Testgeländes Technische Sicherheit der Bundesanstalt für Materialforschung und -prüfung (BAM-TTS) im Rahmen einer Forschungskooperation zwischen der BAM und Gexcon, als Teil des SH2IFT-Programms durchgeführt. Es handelte sich um doppelwandige, vakuumisolierte Tanks von 1 m³ Volumen. Die zylindrischen Tanks unterschieden sich durch ihre Ausrichtung (horizontal oder vertikal) und das verwendete Isoliermaterial (Perlit oder Mehrschichtisolierung (MLI). Der Füllgrad der Tanks betrug bei jedem der durchgeführten Tests etwa 35-40 %. Die Brandlast wurde homogen durch ein propangasbetriebenes Brennersystem erzeugt. Gemessen wurden die Bedingungen im Behälter (Temperaturen und Druck) sowie äußere Randbedingungen und Auswirkungen beim Versagen (Wärmestrahlung, Druckwellen, Flammenballentwicklung und Fragmentierung). Mit Bolometern wurde die Wärmestrahlung gemessen, die sowohl durch das Propanfeuer als auch durch einen möglichen Feuerball/BLEVE erzeugt wurde. Zur Messung der durch das Bersten von Behältern/BLEVEs erzeugten Druckwellen wurden sog. Pencil-Probes verwendet. Des Weiteren wurden mehrere Kameras zur Überwachung der Experimente eingesetzt: Normalbildkameras, Infrarot (IR)-Kameras und Hochgeschwindigkeitskameras, sowohl bodengestützt als auch mittels einer Drohne. Zwei der untersuchten Tanks, ein horizontaler und der vertikale, die beide mit Perlit isoliert waren, hielten der Brandbelastung stand, ohne dass es zu einem Behälterversagen kam. Der mit MLI isolierte horizontale Behälter barst nach 1 Stunde und 6 Minuten und erzeugte dabei einen Feuerball, Trümmerflug und eine Druckwelle. Neben der Beschreibung der Auswirkungen eines kritischen Versagens eines LH2-Tanks sind weitere Ziele der Arbeit die Identifizierung kritischer Behälterzustände sowie die Erstellung eines umfassendes Datensatzes der Trümmer des geborstenen Tanks. Die größten Abstände für kritische Abstände ergaben sich durch Fragmentwurf. Hier sollen 3D-Scans für die Verwendung in CAD und FEM Anwendungen bereitgestellt werden. Umfassende Daten zu den Fragmentwurfweiten, - massen und -positionen wurden bereits publiziert. Damit soll die Voraussetzung geschaffen werden, um vorhandene Wurfweitenmodelle, die bisher nur für einschalige Behälter konzipiert wurden auf ihre Eignung für mehrschalige Behälter zu überprüfen oder mögliche Anpassungen anhand der realen Daten vornehmen zu können. Zudem wurde damit begonnen die nicht geborstenen Tanks zu vermessen und zu zerlegen, um u.a. die Perlit-Schüttung auf Beeinträchtigungen durch den Transport und die Unterfeuerung zu untersuchen.
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein und stellt Prüfverfahren vor. Aus den Ergebnissen durchgeführter Untersuchungen werden Empfehlungen für sicheren Transport und Lagerung abgeleitet.
In einer Versuchsreihe im Realmaßstab wurden drei Flüssigwasserstofftanks (LH2) unterfeuert. Hierbei sollte unter anderem geklärt werden, ob es, analog zu druckverflüssigten Gasen, zu einem BLEVE (Boiling Liquid Expanding Vapor Cloud Explosion) kommen kann. Die Experimente wurden auf dem Testareal Wasserstoffsicherheit des Testgeländes Technische Sicherheit der Bundesanstalt für Materialforschung und -prüfung (BAM-TTS) im Rahmen einer Forschungskooperation zwischen der BAM und Gexcon, als Teil des SH2IFT-Programms durchgeführt. Es handelte sich um doppelwandige, vakuumisolierte Tanks von 1 m³ Volumen. Die zylindrischen Tanks unterschieden sich durch ihre Ausrichtung (horizontal oder vertikal) und das verwendete Isoliermaterial (Perlit oder Mehrschichtisolierung (MLI). Der Füllgrad der Tanks betrug bei jedem der durchgeführten Tests etwa 35-40 %. Die Brandlast wurde homogen durch ein propangasbetriebenes Brennersystem erzeugt. Gemessen wurden die Bedingungen im Behälter (Temperaturen und Druck) sowie äußere Randbedingungen und Auswirkungen beim Versagen (Wärmestrahlung, Druckwellen, Flammenballentwicklung und Fragmentierung). Mit Bolometern wurde die Wärmestrahlung gemessen, die sowohl durch das Propanfeuer als auch durch einen möglichen Feuerball/BLEVE erzeugt wurde. Zur Messung der durch das Bersten von Behältern/BLEVEs erzeugten Druckwellen wurden sog. Pencil-Probes verwendet. Des Weiteren wurden mehrere Kameras zur Überwachung der Experimente eingesetzt: Normalbildkameras, Infrarot (IR)-Kameras und Hochgeschwindigkeitskameras, sowohl bodengestützt als auch mittels einer Drohne. Zwei der untersuchten Tanks, ein horizontaler und der vertikale, die beide mit Perlit isoliert waren, hielten der Brandbelastung stand, ohne dass es zu einem Behälterversagen kam. Der mit MLI isolierte horizontale Behälter barst nach 1 Stunde und 6 Minuten und erzeugte dabei einen Feuerball, Trümmerflug und eine Druckwelle. Neben der Beschreibung der Auswirkungen eines kritischen Versagens eines LH2-Tanks sind weitere Ziele der Arbeit die Identifizierung kritischer Behälterzustände sowie die Erstellung eines umfassendes Datensatzes der Trümmer des geborstenen Tanks. Die größten Abstände für kritische Abstände ergaben sich durch Fragmentwurf. Hier sollen 3D-Scans für die Verwendung in CAD und FEM Anwendungen bereitgestellt werden. Umfassende Daten zu den Fragmentwurfweiten, -massen und -positionen wurden bereits publiziert. Damit soll die Voraussetzung geschaffen werden, um vorhandene Wurfweitenmodelle, die bisher nur für einschalige Behälter konzipiert wurden auf ihre Eignung für mehrschalige Behälter zu überprüfen oder mögliche Anpassungen anhand der realen Daten vornehmen zu können.
Zudem wurde damit begonnen die nicht geborstenen Tanks zu vermessen und zu zerlegen, um u.a. die Perlit-Schüttung auf Beeinträchtigungen durch den Transport und die Unterfeuerung zu untersuchen.
In einer Reihe von Experimenten wurden die möglichen Folgen der Freisetzung von verflüssigtem Wasserstoff (LH2) auf, bzw. unter Wasser untersucht. Die Experimente zielten darauf ab, eine unbeabsichtigte Freisetzung von LH2 (z.B. durch Schlauchabriss) insbesondere bei der Betankung eines Schiffes zu simulieren. Für verflüssigtes Erdgas (LNG) wurden dabei sog. RPT’s (rapid phase transition) nachgewiesen, bei denen die spontane Verdampfung relevante Druckwellen erzeugt. Es kann nicht ausgeschlossen werden, dass RPTs auch im Falle von LH2 möglich sind. Die Versuche wurden auf dem Testareal Wasserstoffsicherheit auf dem Testgelände Technische Sicherheit der Bundesanstalt für Materialforschung und -prüfung (BAM-TTS) in Horstwalde, im Rahmen einer Forschungskooperation zwischen der BAM und Gexcon im Rahmen des SH2IFT-Programms durchgeführt. Die LH2-Freisetzungen erfolgten direkt aus einem LH2-Tanklastwagen über eine lange, flexible, vakuumisolierte Transferleitung. Während die Freisetzung oberhalb und unterhalb der Wasseroberfläche jeweils vertikal orientiert war, wurde bei der Unterwasserfreisetzung zusätzlich eine horizontale Ausströmung, parallel zur Wasseroberfläche realisiert. Zur Bestimmung des Massenstromes, wurde ein Wägesystem unter dem Tankwagen eingesetzt. Spezielle Drucksensoren wurden verwendet, um die durch die Freisetzungsvorgänge erzeugten Stoßwellen sowohl im Wasser als auch in der Luft zu messen. Die Gaskonzentrationen über dem Wasserbecken wurden an verschiedenen Positionen gemessen. Hochgeschwindigkeits-, Infrarot- (IR) und normale Kameras wurden eingesetzt, um die Phänomenologie der Freisetzung aufzuzeichnen und das Verhalten der Gaswolke im Zeitverlauf zu verfolgen. Neben den fest installierten Systemen an Land, kamen auch Unterwasserkameras sowie eine Drohne mit Normal- und IR-Kameras zum Einsatz.
Zwei Wetterstationen wurden zur Messung von Windgeschwindigkeit, Windrichtung, Temperatur und Luftfeuchtigkeit während aller durchgeführten Tests eingesetzt. Des Weiteren kamen Bolometer zur Wärmestrahlungsmessung zum Einsatz. Zwar führten die Freisetzung zu einer hochturbulenten LH2/Wasser Mischzone, jedoch zu keinen nennenswerten Überdrücken durch RPT. Im Gegensatz dazu wurde unerwartet, aber reproduzierbar, eine Zündung der Gaswolke in freier Luft in einiger Entfernung von den Instrumenten und dem Ort der Freisetzung beobachtet. Die daraus resultierenden Gaswolkenexplosionen führten zu relevanten Überdrücken und zur Wärmeabstrahlung in die Umgebung.
Holzkohlen im Seeverkehr - Selbstentzündung vermeiden, sichere Beförderungsbedingungen schaffen
(2024)
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holz- und Pflanzenkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Ergebnisse eines Projektes zur systematischen Untersuchung verschiedener Pflanzenkohlen werden vorgestellt.
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein, stellt Prüfverfahren vor und gibt Empfehlungen für sicheren Transport und Lagerung.
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein, stellt Prüfverfahren vor und gibt Empfehlungen für sicheren Transport und Lagerung.
As part of the development of a new standard testing procedure, a round robin study was conducted by six participating laboratories. This study involved the measurement of both the maximum explosion pressure and the maximum rate of pressure rise for hybrid mixtures comprising dust and vapor. Measurements were performed using a modified 20L-sphere. The primary objective of this collaborative effort was to assess the accuracy, reliability, and consistency of analytical and measurement methods across multiple laboratories, thereby increasing confidence in the obtained results. The method and protocol were developed as part of the NEX-HYS project and documented in a technical specification by the German Institute for Standardization Registered Association (DIN). The study revealed that precise pre-ignition pressure rise (PIPR) measurements and the use of a leak-free test apparatus significantly influenced the results of the measured maximum explosion pressure and maximum pressure rise rate.
The combustion characteristics and explosive hazard of syngas (H2/CO)/air mixtures are affected by its exact composition and equivalence ratios. In this paper, the explosion pressure and spectral radiant intensity of free radicals were quantitatively examined for syngas with different H2 proportions ([H2 in syngas] = 0, 30, 50, 70, 100 vol%) and equivalence ratios (φ = 0.8, 1.0, 1.2, 1.4, 1.6, 2.0, 2.5). The results show that the explosion process of syngas/air mixtures can be separated into the initial slow combustion stage, the violent deflagration stage and the deflagration ending stage. The peaks of explosion pressure, pressure rise rate, OH*spectral intensity and rise rate of spectral intensity first increase and then decrease with increasing the equivalence ratio, and they reduce gradually with the decrease of H2 proportion in syngas. The H2 content in syngas greatly affects the heat release and the concentration of excited state OH*, especially for the syngas/air mixtures with smaller proportion of H2. Additionally, the presence of H2 greatly increases the deflagration index and spectral radiant index of OH* for syngas/air mixtures. The average rise rates of explosion pressure and spectral intensity of free radicals are introduced and the coupling model between them is established based on the first law of thermodynamics and the principle of chain reaction. The established model is furthermore verified by the experimental results. It is indicated that there is a linear relationship between average rise rates of explosion pressure and spectral intensity (OH*). The results can be used to improve the combustion efficiency of syngas and to guide theoretically the prevention, mitigation and control of syngas explosions.
Explosionsverletzungen gehören zu den häufigsten Verletzungen bei militärischen Einsätzen. Während die Auswirkungen von Splittern, die als sekundäre Explosionsverletzungen eingestuft werden, durch die modernen ballistischen Körperschutzsysteme der Polizei und des Militärs minimiert werden konnten, stellen die Auswirkungen der Stoßwellenausbreitung im Körper als Teil des primären Explosionstraumas nach wie vor eine ernsthafte Bedrohung dar. Zusätzlich zu einzelnen einsatzbedingten Lastfällen liegt ein wissenschaftlicher Fokus auf besonders exponiertem Personal, z.B. aus den Einsatzbereichen „Taktische Zugangstechnik“, „Präzisionsschützenwesen“ oder Steilfeuerwaffen (Mörser). Repetitive mild traumatic brain injury (mTBI) können gesundheitliche Langzeitschädigungen wie und chronic traumatic encephalopathy (CTE) erzeugen.
Um einen Beitrag zur Erforschung der primären Explosionswirkungen zu leisten, hat die Bundeswehr in Zusammenarbeit mit dem Bundeswehrkrankenhaus Berlin und der Bundesanstalt für Materialforschung und -prüfung (BAM) ein interdisziplinäres wehrmedizinisches Sonderforschungsvorhaben eingerichtet. Ziel der geplanten Untersuchung ist die Entwicklung einer multidisziplinären Methode zur Analyse des Stoßwellenverhaltens in verschiedenen generischen Gewebesimulanzien, sowie Schutzmaterialien unter möglichst realitätsnahen und reproduzierbaren Bedingungen.
Für die Erzeugung reproduzierbarer Stoßwellen wurde ein Autoklav
(Druckbehälter) entwickelt, mit dem durch die detonative Umsetzung eines Acetylen-Sauerstoff-Gemisches gut reproduzierbare Druckwellen unter Freifeldbedingungen erzeugt werden können. Vorteile dieser Methode sind unter anderem die kurzen Rüstzeiten zwischen Versuchsdurchgängen, die Minimierung störender Einflüsse im Vergleich zu Stoßwellenrohren und die geringeren Sicherheitsanforderungen im Vergleich zur Anwendung von konventionellen Sprengstoffen. Das generische Torso-Modell besteht in seiner einfachsten Form aus einem mit Druck- und Beschleunigungssensoren instrumentierten Gelatineblock, welcher eine Simulanz für organisches Gewebe darstellt. Zur Untersuchung des Stoßwellenverhaltens wurden verschiedene Medien, wie Hohlkörper, Festkörper und Gewebesimulanzien differenter Dichte in das generische Torso-Modell eingebracht. Einen besonderer Untersuchungsschwerpunkt bildeten die Grenzbereiche zwischen den unterschiedlichen Medien. Des Weiteren wurde analysiert, wie sich verschiedene Schutzmaterialien auf das Stoßwellenverhalten auswirken und mit welchen veränderten Eigenschaften die Stoßwelle anschließend in die Gewebesimulanz einkoppelt.
Large-scale experiments have been performed to investigate the possible consequences of realistic amounts of liquified hydrogen (LH2) encountering water. The experiments aimed at simulating an accidental release of LH2 during especially the fuelling of a ship. For liquified natural gas (LNG) it has been demonstrated that when spilled onto water the evaporation rate can be that high that physical explosions occur which are referred as rapid phase transitions (RPTs). It cannot be excluded that RPTs are also possible in the case of LH2. The tests were performed in a 10 m x 10 m x 1.5 m basin filled with water, at the Test Site Technical Safety of the Bundesanstalt für Materialforschung und –prüfung (BAM) in Horstwalde, Germany within a research cooperation between BAM and Gexcon as part of
the SH2IFT program. LH2 releases were established releasing directly from a trailer carrying LH2 through a long flexible double vacuum insulated transfer line. The releases occurred from a height of 50 cm above and 30 cm under the water surface both pointing downwards and 30 cm under the water surface pointing along the water surface too. The release rate was determined based on the weight loss rate of the road tanker which was placed onto load cells. Special blast pressure sensors were used to measure the shock waves generated by the release processes both in the water and in the air. At several locations the gas concentration was measured. Heat radiation was measured at 3 distances from the point of release. High speed,
Infrared (IR) and normal cameras were used to record events and to follow the gas cloud behaviour in time. This includes cameras mounted on a UAV and underwater cameras. Two weather stations were used to measure wind speed, wind direction, temperature and humidity during all tests performed. All investigated release configurations resulted in a very chaotic LH2-water mixing zone, causing considerable evaporation but only minor over pressures.
The main phenomenon observed was an ignition of the released gas cloud, resulting in significant blast wave overpressures and heat radiation to the surroundings. The location of the ignition occurred in free air at some distance from the instrumentation and release location.
Large Scale Experiments have been performed to determine whether a storage vessel containing liquid hydrogen (LH2) and caught in a fire engulfing the vessel can result in a BLEVE (Boiling Liquid Expanding Vapour Explosion) and if so its consequences. The tests were performed at the Test Site Technical Safety of the Bundesanstalt für Materialforschung und –prüfung (BAM) in Germany at the Hydrogen Test Area (H2TA) within a research cooperation between BAM and Gexcon as part of the SH2IFT program. Three tests were performed using double-walled vacuum insulated vessels of 1 m3 volume. The cylindrical Vessels differed in orientation (horizontal or vertical) and the insulation material used (perlite or multi-layer insulation (MLI)). The degree of filling of the vessels was approximately 35-40 % in each of the tests performed. The fire load was provided by a propane fed burner-system positioned under the storage vessel and designed to give a homogeneous fire load. The conditions in the vessel (temperatures and pressure) as well as external effects (heat radiation, blast waves, flame ball development and fragmentation) were measured. All vessels were equipped with K-type thermocouples at several locations at the inner and outer vessel shell. The pressure inside the inner vessel and in the space between the inner and outer vessels (vacuum pressure) was measured. Bolometers were used to measure the heat radiation generated by both the propane fire and that generated by a possible fireball/BLEVE. To measure blast generated by the vessel burst/BLEVEs blast pencils were positioned at up to three locations. Further several cameras were used to monitor the events: normal cameras, infrared (IR)-cameras, high-speed cameras also on board of an UAV. Two of these vessels, a horizontal and a vertical vessel both insulated with perlite withstood the fire loading for 1 hour 20 minutes and 4 hours respectively without catastrophic failure. A horizontal vessel insulated with MLI failed by bursting after 1 hour and 6 minutes resulting in a fireball, fragments, and blast wave.
Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören.
Bei mechanisch erzeugten Schlag-, Schleif- und Reibvorgängen kommt es infolge des Zusammenstoßes bzw. des Reibens zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen.
Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann.
Ferner finden sich in der TRGS 723 Hinweise zum Umgang mit funkenarmen Werkzeugen im explosionsgefährdeten Bereich.
Die Einführung von Wasserstoff als sicherer Energieträger braucht eine robuste Wissensbasis, darauf aufgebaute Werkzeuge zur Auslegung und Sicherheitsbewertung von Wasserstofftechnologien und ein international harmonisiertes Regelwerk. Viele der innovativen Technologien implizieren Wasserstoff bei hohen Drücken und/oder kryogenen Temperaturen, mit denen in verteilten Anwendungen erstmalig private Nutzer in Kontakt kommen. Um überkonservative, teure Sicherheitslösungen zu vermeiden, gleichzeitig aber die Einsetzbarkeit und Sicherheit von Wasserstoffanwendungen zu demonstrieren und die Akzeptanz für die Technologie aufrecht zu halten, muss auch die Sicherheitsforschung mit den Trends der technologischen Entwicklung Schritt halten, oder sie besser noch antizipieren. So beschreibt dieser Überblicksartikel nicht nur den gegenwärtigen Stand der Kenntnisse und Technik bezüglich Wasserstoffsicherheit, sondern auch ihre Weiterentwicklung.
Experimental Setup for the Reproducible Generation of Pressure Waves in Free Field Conditions
(2023)
The injuries caused by the primary blast are still poorly understood, especially in the torso region. To generate sufficiently large data sets, shock tubes are often used. However, these have some limitations, such as blockage, use of the exit jet, widening cross-sections, and scaling problems with respect to compressive strength and test objects. Therefore, it is appropriate to conduct experiments under free-field conditions, but tests with real explosives are often associated with long preparation and setup times as well as high safety requirements.
Therefore, this paper presents an experimental setup for the reproducible generation of blast waves under free-field conditions. This experimental setup aims to provide a test environment for a sufficiently large specimen to investigate the behaviour of the shock wave within the specimen, especially at the media interfaces. As an example of application, the influence of the primary explosive effect on protective equipment or on tissue simulants for the investigation of blast injuries can be mentioned. An autoclave is used as a shock wave generator. It has a volume of 0.065 m3 and is filled with a stoichiometric acetylene-oxygen gas mixture. The setup and turnaround time is approximately 30 minutes. The following factors have been selected as target variables for the optimization of the shock wave generator: reproducibility of the pressure wave, use-case-relevant positive phase duration and peak overpressure, a pressure curve characteristic corresponding to that of a military explosive under undisturbed free field conditions, and short setup times of the experimental setup. For this purpose, the experimental setup is presented in this paper. Several series of measurements are presented, showing the characteristics of the generated pressure wave. For the generated pressure wave, the classical pressure curve characteristics can be clearly recognized. A peak pressure of 92 kPa is reached at a distance of 1 m from the opening, and the first positive pressure phase lasts 1.17 ms. Furthermore, the pressure wave propagates in a hemispherical shape. The typical characteristics of the blast wave generated by the SWG have been demonstrated using the military explosive PETN. It is shown that the actual load case corresponds to about 70 g of PETN.
Experimental Setup for the Reproducible Generation of Pressure Waves in Free Field Conditions
(2023)
The injuries caused by the primary blast are still poorly understood, especially in the torso region. To generate sufficiently large data sets, shock tubes are often used. However, these have some limitations, such as blockage, use of the exit jet, widening cross-sections, and scaling problems with respect to compressive strength and test objects. Therefore, it is appropriate to conduct experiments under free-field conditions, but tests with real explosives are often associated with long preparation and setup times as well as high safety requirements.
Therefore, this paper presents an experimental setup for the reproducible generation of blast waves under free-field conditions. This experimental setup aims to provide a test environment for a sufficiently large specimen to investigate the behaviour of the shock wave within the specimen, especially at the media interfaces. As an example of application, the influence of the primary explosive effect on protective equipment or on tissue simulants for the investigation of blast injuries can be mentioned. An autoclave is used as a shock wave generator. It has a volume of 0.065 m3 and is filled with a stoichiometric acetylene-oxygen gas mixture. The setup and turnaround time is approximately 30 minutes. The following factors have been selected as target variables for the optimization of the shock wave generator: reproducibility of the pressure wave, use-case-relevant positive phase duration and peak overpressure, a pressure curve characteristic corresponding to that of a military explosive under undisturbed free field conditions, and short setup times of the experimental setup. For this purpose, the experimental setup is presented in this paper. Several series of measurements are presented, showing the characteristics of the generated pressure wave. For the generated pressure wave, the classical pressure curve characteristics can be clearly recognized. A peak pressure of 92 kPa is reached at a distance of 1 m from the opening, and the first positive pressure phase lasts 1.17 ms. Furthermore, the pressure wave propagates in a hemispherical shape. The typical characteristics of the blast wave generated by the SWG have been demonstrated using the military explosive PETN. It is shown that the actual load case corresponds to about 70 g of PETN.
minimum explosion concentration (MEC) and limiting oxygen concentration (LOC) in our recent works. This work further studies the reasonability and reliability of the alternative method experimentally and theoretically. Six different dust samples were tested via a 20-L spherical explosion chamber. The experimental results showed that the data of MEC and LOC determined by using the alternative and the standardized methods are in good agreement. The minimum flame propagation velocity (Sf) and the corresponding maximum combustion duration time (tc) were found at its MEC and LOC, suggesting that the theoretical analysis can well explain all the experimental data. It is the first time to study the theoretical basis of the explosion criterion, thus helping to improve our understandings of dust explosion characteristics, and to amend the explosion criterion in future test standards.
Im Rahmen dieses Vortrags wurden aktuelle Arbeiten der BAM im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. Den Schwerpunkt des Vortrags bildeten die Auswirkungen der kumulierten Belastung durch "low-level blast" auf das Gehirn von Einsatzkräften und Rückschlüsse für den Arbeitsschutz und die Arbeitsmedizin.
The presented research work examines the effects of different fuel-air equivalence ratios and initial pressure on ignition temperature.
This study shows a non-monotonic pressure dependence in stoichiometric mixtures at varying pressures from 1 to 10 bar and a low sensitivity to changes in the equivalence ratio (0.5-2). The results form the basis for our future research into the complex interaction between lubricant characteristics and hydrogen-air mixtures to better understand pre-ignition phenomena in internal combustion engines.
Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören.
Bei mechanischen Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen.
Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann.
Within a research cooperation between BAM and Gexcon as part of the SH2IFT program, large scale experiments have been performed at the Test Site Technical Safety of the Bundesanstalt für Materialforschung und –prüfung (BAM) to determine the hazards emerging from a vacuum insulated cryogenic storage vessel containing liquified hydrogen (LH2) is caught in a fire engulfing it.
In dem hier vorgestellten Projekt wurde die Wirksamkeit mechanischer Schläge als Zündquelle für wasserstoffhaltige Atmosphären in Abhängigkeit von der inhomogenen Materialpaarung systematisch untersucht. Dabei wurden praxisrelevante Materialien wie Edelstahl, niedrig legierter Stahl, Beton und Nichteisenmetalle betrachtet. Es wurde festgestellt, dass eine Zündung vermieden werden kann, wenn Nichteisenmetalle in Kombination mit verschiedenen metallischen Werkstoffen verwendet werden. In Kombination mit Beton muss die kinetische Schlagenergie auch mit Nichteisenmetallen weiter begrenzt werden, um eine wirksame Entzündung zu vermeiden. Außerdem wurde untersucht, wie sich die Beimischung von Wasserstoff zu Erdgas auf die Wirksamkeit mechanischer Stöße als Zündquelle auswirkt. Bei Beimischungen von bis zu 25 % Wasserstoff und sogar mehr konnte kein Einfluss festgestellt werden. Die Ergebnisse sind vor allem relevant im Zusammenhang mit der Umwidmung des Erdgasnetzes oder der Beimischung von Wasserstoff im Erdgasnetzes.
Ammonia Safety
(2023)
In order to share the latest technological information in the gas field and develop the gas industry, the Korean Gas Safety Corporation host an international gas safety seminar every year by inviting domestic and foreign experts. In year 2023, the seminar focussed on the latest trends in ammonia safety management and utilization technology. BAM was asked to give a presentation on ammonia safety and its flammability in specific. Based on the international flammability classification the required explosion protection measures were presented,which are defined by the European ATEX rules. As final part of the presentation the German strategy on transformation of existing infrastructure, here especially the transformation of landbased LNG terminals, was shown as well.
Ammonia Safety
(2023)
Ammonia is an energy source that has been produced and used on a large scale for many decades, primarily as a fertilizer or feedstock in nitrogen chemistry. The CAMPFIRE alliance, founded as part of the "WIR!- Wandel durch Innovation in der Region" funding program of the German Federal Ministry of Education and Research (BMBF), aims to research and develop new energy conversion and storage technologies for the future energy system based on green ammonia. The safe handling of ammonia is an important issue along the entire value chain. Therefore, the alliance has organized a webinar to discuss the topic of ammonia safety and in particular its flammability. BAM's contribution presented the topic of flammability in detail, placed the classification of ammonia in an international, European and national context and presented the basic principles of explosion protection that result from this and must be observed during use and application.
Safety characteristics like the lower explosion limit, the highest concentration for a given substance mixed with air that does not result in a self-propagating flame, or the maximum explosion pressure, the highest pressure that can be reached after ignition for a given combustible substance mixed with air at any concentration, are widely used in the industry to either prevent an explosion or to mitigate the effects of it. Safety characteristics are not physical constants, are determined experimentally and depend on the chosen experimental parameters such as the ignition energy or turbulence.
For the determination of the safety characteristics lower explosion limit (LEL), limiting oxygen concentration (LOC), maximum explosion pressure (pmax) and maximum rate of pressure rise ((dp/dt)max) of gases and vapors the gas is filled via partial pressures into a test vessel and then ignited under quiescent conditions with a weak (2 J - 20 J) ignition source. For dusts, the same safety characteristics are determined under turbulent conditions to elevate
the dust homogeneously and it is ignited with two chemical igniters with an ignition energy of 1000 J each (LEL and LOC) or 5000 J each (pmax and (dp/dt)max). For the determination of safety characteristics of hybrid mixtures (a mixture containing a combustible dust and a flammable gas) there is no existing standard.
In the last 40 years most of the research on their safety characteristics was performed with dust testing equipment that was modified for the addition of flammable gas. Because of the different mixing procedures of gases and dusts with air and because of different ignition energies and sources that are normally used for the standard tests of gases or dusts, the results were hardly reproducible. Statements about the different safety characteristics were contradictory and left the reader or the person responsible for designing safety measures for a process plant or a facility behind with no clear suggestion about the behavior of hybrid
mixtures.
This thesis is aimed on determining the influence of the different ignition sources and energies on the safety characteristics pmax, (dp/dt)max, lower explosion limit, and limiting oxygen concentration of hybrid mixtures.
Several test series were conducted to characterize different standardized ignition sources, that are already in use for the determination of safety characteristics of single-phase substances (gases, liquids, dusts). The burning duration, the igniting volume and the net energy were investigated.
It was shown, that the chemical igniters and the exploding wire are suitable ignition sources for the determination of safety characteristics of hybrid mixtures in general. Their burning duration was long enough to ignite dusts and quick enough, that the decay of the turbulence or sedimentation of the dusts did not occur. Both ignition sources produced comparable results for the determination of pmax, LEL and (dp/dt)max of dusts when they had the same ignition energy. A reduced ignition energy of the exploding wire and the chemical igniters did not affect the pmax and (dp/dt)max. The LEL changed with lower energies. However, for the determination of the LOC of hybrid mixtures the exploding wires with an overall energy of 2 kJ produced the best results.
The influence of the different mixing procedures that have already been used for hybrid mixtures and the requirements for them were also investigated experimentally for the gas concentration and the determined safety characteristics and compared to each other. It was shown, that the partial pressure method works for mixing hybrid mixtures but the pressures should be measured very accurately and the gas concentration should be validated.
Furthermore, the influence of the turbulence that is inevitable when testing dusts, on the safety characteristics of gases was determined. It was found that the chemical igniters and exploding wires produced comparable results for the determination of pmax, LEL and (dp/dt)max under turbulence. For the LOC only exploding wires with two times 1 kJ worked.
Finally, the safety characteristics of hybrid mixtures were determined with different ignition energies and sources and the data were compared. It was discovered, that the pmax of hybrid mixtures was the same value than the higher determined one of the single substances while (dp/dt)max of hybrid mixtures was about 10 % to 25 % higher than the value of the stoichiometric gas mixture under turbulence. The point was found at the stoichiometric gas concentration with very little amounts of dust.
To prove the key findings of this work and for the establishment of a standardized procedure for the determination of safety characteristics of hybrid mixtures, an international round robin test was conducted with eleven participating facilities in seven countries. The results were comparable within a reasonable range and are presented in this dissertation in an extra chapter.
Based upon the observations in this work a reliable solution for a new standardizable ignition source to determine the safety characteristics of hybrid dust-gas-mixtures is proposed.
Safety characteristics are widely used in industrial processes to avoid explosive atmospheres (primary explosionprotection) or to mitigate the consequences of an explosion (constructive explosion protection). Several laboratory parameters influence the determined values when performing the test series such as the beginning pressure and the pre-ignition pressure rise, the ignition source, the ignition energy, the burning duration and volume or the concentration of the combustible substance.
In the different standards for the determination of safety characteristics of dusts there is no statement about the scattering or the deviation when parameters are chosen or occur on the borders of their allowed range. Thus, two laboratories might determine values that are hardly comparable for the same given substance.
This article summarizes some of the influential factors that cause a deviation and shows the inherent scattering of dust tests when all other parameters are kept constant. It also provides some advice how to minimize the deviation and the scattering with little effort.
In the field of explosive reactions, there is a type of explosive effect that lacks a sufficient database and reproducible experiments regarding biomechanics. It concerns the primary explosive effect. It is defined as pure shock wave of the explosion. The physical behavior of the shock wave when interacting with different types of tissue and, in particular, the subsequent transitions of the shock wave, have barely been investigated. The transition of the shock wave into other materials is the focus of the research Therefore, the aim of the investigations is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times. An autoclave is used to generate the pressure waves. A simplified torso model consisting of ballistic gelatin is used as a simulant.
In this paper, the influence of protective equipment on the pressure load in the tissue simulant is investigated. For this purpose, consecutive test setups are used. First, the behavior of ballistic gelatin as a tissue simulant is investigated. Then, the simplified torso model is covered with typical combat clothing consisting of four layers.
Afterwards a currently used UHMWPE ballistic protective plate is placed in front of the simplified torso model.
Finally, the combat clothing and the protective plate are examined in combination. Three cast-in pressure sensors are used as measuring devices, as well as an acceleration sensor attached to the protective plate.
The experiments show that the maximum overpressure in a model rotected by combat clothing and the protective plate can be reduced by 95%. However, the propagation speed of the shock wave within the simplified torso model increases from 1535.5 m/s to 2204.5 m/s. This shows that even protective equipment, which is not primarily intended to protect against blast, offers a significant reduction in the pressure load in the protected area. On the one hand it is caused by the media transition from air to PE and the resulting higher reflection of the acceleration of the transmitted wave within the simulant. On the other hand, it is also reduced due to the damping and dispersion caused by the clothing layers.
In the field of explosive reactions, there is a type of explosive effect that lacks a sufficient database and reproducible experiments regarding biomechanics. It concerns the primary explosive effect. It is defined as pure shock wave of the explosion. The physical behavior of the shock wave when interacting with different types of tissue and, in particular, the subsequent transitions of the shock wave, have barely been investigated. The transition of the shock wave into other materials is the focus of the research Therefore, the aim of the investigations is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times. An autoclave is used to generate the pressure waves. A simplified torso model consisting of ballistic gelatin is used as a simulant. In this paper, the influence of protective equipment on the pressure load in the tissue simulant is investigated. For this purpose, consecutive test setups are used. First, the behavior of ballistic gelatin as a tissue simulant is investigated. Then, the simplified torso model is covered with typical combat clothing consisting of four layers. Afterwards a currently used UHMWPE ballistic protective plate is placed in front of the simplified torso model. Finally, the combat clothing and the protective plate are examined in combination. Three cast-in pressure sensors are used as measuring devices, as well as an acceleration sensor attached to the protective plate. The experiments show that the maximum overpressure in a model protected by combat clothing and the protective plate can be reduced by 95%. However, the propagation speed of the shock wave within the simplified torso model increases from 1535.5 m/s to 2204.5 m/s. This shows that even protective equipment, which is not primarily intended to protect against blast, offers a significant reduction in the pressure load in the protected area. On the one hand it is caused by the media transition from air to PE and the resulting higher reflection of the acceleration of the transmitted wave within the simulant. On the other hand, it is also reduced due to the damping and dispersion caused by the clothing layers.
The number of cars which use a battery for propulsion, like BEV (battery electric vehicle) or PHEV (plug-in hybrid electric vehicle), is increasing. Following, the probability of these car types being involved in car accidents will increase. In a worst-case accident scenario, the installed batteries could go under thermal runaway (TR). A TR could be initiated by various causes, e.g., high temperatures from outside, mechanical damage of the cells/modules/batteries or internal and external short circuits. During such an event, large amounts of heat and toxic and/or flammable gases are released. This poses a great hazard to people and property in the immediate vicinity. The paper describes a large-scale test series on the lithium-ion battery TR consequences of automobile cells and modules up to E = 6.85 kWh. Near field temperatures of ΔT > 800°C in a distance of l = 2 m were measured. During an overcharge test, fragment throwing distances of l > 30 m were detected. Subsequent gas explosions of the released gases were documented. Hydrogen fluoride (HF) was measured in all tests, from cell to module. The highestmeasured concentration was cHF = 76 ppm, which is significantly higher than the 30-min-level for AEGL 2 (acute exposure guideline level 2). Based on the experimentally determined consequences, concrete measures for the accident analysis are subsequently drawn.
The number of cars which use a battery for propulsion, like BEV (battery electric vehicle) or PHEV (plug-in hybrid electric vehicle), is increasing. Following, the probability of these car types being involved in car accidents will increase. In a worst-case accident scenario, the installed batteries could go under thermal runaway (TR). A TR could be initiated by various causes, e.g., high temperatures from outside, mechanical damage of the cells/modules/batteries or internal and external short circuits. During such an event, large amounts of heat and toxic and/or flammable gases are released. This poses a great hazard to people and property in the immediate vicinity. The paper describes a large-scale test series on the lithium-ion battery TR consequences of automobile cells and modules up to E = 6.85 kWh. Near field temperatures of ΔT > 800°C in a distance of l = 2 m were measured. During an overcharge test, fragment throwing distances of l > 30 m were detected. Subsequent gas explosions of the released gases were documented. Hydrogen fluoride (HF) was measured in all tests, from cell to module. The highest measured concentration was cHF = 76 ppm, which is significantly higher than the 30-min-level for AEGL 2 (acute exposure guideline level 2). Based on the experimentally determined consequences, concrete measures for the accident analysis are subsequently drawn.
Thermal runaway investigations were performed by subjecting single and double NMC pouch cells to thermal abuse condition inside an air-tight reactor vessel with an internal volume of 100 dm³. The study was divided into two series. The findings revealed the thermal runaway-induced explosion in the cells results in a rate of temperature increase greater than 10 K/s. The highest gaseous production was achieved at a range of 90 – 100% SOC and higher battery capacities 0.79 L/Wh (Series 1, 10 Ah cell) and 0.87 L/Wh (Series 2, 32 Ah cell). The investigation showed between 25 m³ and 84 m³ of explosible gas mixture could be released from electric vehicles of nominal useable electrical energy from 32 kWh up to 108 kWh at thermal runaway. It was also found that, the release of these explosible gases could undergo a secondary explosion.