2.1 Sicherheit von Energieträgern
Filtern
Erscheinungsjahr
- 2023 (56) (entfernen)
Dokumenttyp
- Vortrag (35)
- Zeitschriftenartikel (13)
- Beitrag zu einem Tagungsband (4)
- Beitrag zu einem Sammelband (1)
- Dissertation (1)
- Posterpräsentation (1)
- Forschungsbericht (1)
Schlagworte
- H2Safety@BAM (9)
- Lithium-ion battery (7)
- Blast injury (5)
- Experimental setup (5)
- Schlagfunken (5)
- Shock wave generator (5)
- Consequences (4)
- Electrical Energy Storage (4)
- Hydrogen (4)
- Nichtelektrische Funken (4)
Organisationseinheit der BAM
- 2 Prozess- und Anlagensicherheit (56)
- 2.1 Sicherheit von Energieträgern (56)
- 3 Gefahrgutumschließungen; Energiespeicher (4)
- 7 Bauwerkssicherheit (4)
- 7.5 Technische Eigenschaften von Polymerwerkstoffen (4)
- 9 Komponentensicherheit (4)
- 3.5 Sicherheit von Gasspeichern (3)
- 9.0 Abteilungsleitung und andere (3)
- 9.6 Additive Fertigung metallischer Komponenten (3)
- 2.0 Abteilungsleitung und andere (1)
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (35)
Blast injuries are among the most common injuries in military operations. Also, in civilian environments, more explosive threats are expected in the future due to emerging conflicts and threats. While the effect of fragments, which is classified as secondary blast injury, could be minimized by police and military personnel’s modern ballistic body protection systems, the effects of shock wave propagation in the body as part of the primary explosion trauma still remain a serious threat needing further research.
The detonation-physical processes of highly dynamic pressure changes within the human body, the reflection-related amplification of shock waves at organ-dermis interfaces, and the consequences of injury mechanisms have become more prominent in international research. Various approaches have been used to investigate these aspects. Animal experiments on free field test sites or shock tube setups combined with a subsequent biological evaluation and numerical simulations provided promising results and allowed the discussion of different biomechanical aspects. However, due to poor reproducibility and a lack of short-term dynamic material properties, most research approaches have significant limitations. Laboratory test setups do not represent real-scale high explosive detonation parameters with regards to pressure characteristics, impulse duration and blockage problems. Measured values are interpreted with partly outdated, selective and not validated limit values for overpressures from field tests with animals. This is due to the lack of a validated and comprehensive data set covering a variation of the crucial parameter. Injury mechanisms and their effects have not yet been sufficiently elucidated for the torso and extremities.
In order to contribute to the research efforts on the primary explosion effects, the German Federal Armed Forces established an interdisciplinary military medical research project in cooperation of the Bundeswehr Hospital Berlin and the German Federal Institute for Materials Research and Testing (BAM). The aim of the planned investigation is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times.
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein, stellt Prüfverfahren vor und gibt Empfehlungen für sicheren Transport und Lagerung.
Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert.
Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein, stellt Prüfverfahren vor und gibt Empfehlungen für sicheren Transport und Lagerung.
Die Einführung von Wasserstoff als sicherer Energieträger braucht eine robuste Wissensbasis, darauf aufgebaute Werkzeuge zur Auslegung und Sicherheitsbewertung von Wasserstofftechnologien und ein international harmonisiertes Regelwerk. Viele der innovativen Technologien implizieren Wasserstoff bei hohen Drücken und/oder kryogenen Temperaturen, mit denen in verteilten Anwendungen erstmalig private Nutzer in Kontakt kommen. Um überkonservative, teure Sicherheitslösungen zu vermeiden, gleichzeitig aber die Einsetzbarkeit und Sicherheit von Wasserstoffanwendungen zu demonstrieren und die Akzeptanz für die Technologie aufrecht zu halten, muss auch die Sicherheitsforschung mit den Trends der technologischen Entwicklung Schritt halten, oder sie besser noch antizipieren. So beschreibt dieser Überblicksartikel nicht nur den gegenwärtigen Stand der Kenntnisse und Technik bezüglich Wasserstoffsicherheit, sondern auch ihre Weiterentwicklung.
Experimental Setup for the Reproducible Generation of Pressure Waves in Free Field Conditions
(2023)
The injuries caused by the primary blast are still poorly understood, especially in the torso region. To generate sufficiently large data sets, shock tubes are often used. However, these have some limitations, such as blockage, use of the exit jet, widening cross-sections, and scaling problems with respect to compressive strength and test objects. Therefore, it is appropriate to conduct experiments under free-field conditions, but tests with real explosives are often associated with long preparation and setup times as well as high safety requirements.
Therefore, this paper presents an experimental setup for the reproducible generation of blast waves under free-field conditions. This experimental setup aims to provide a test environment for a sufficiently large specimen to investigate the behaviour of the shock wave within the specimen, especially at the media interfaces. As an example of application, the influence of the primary explosive effect on protective equipment or on tissue simulants for the investigation of blast injuries can be mentioned. An autoclave is used as a shock wave generator. It has a volume of 0.065 m3 and is filled with a stoichiometric acetylene-oxygen gas mixture. The setup and turnaround time is approximately 30 minutes. The following factors have been selected as target variables for the optimization of the shock wave generator: reproducibility of the pressure wave, use-case-relevant positive phase duration and peak overpressure, a pressure curve characteristic corresponding to that of a military explosive under undisturbed free field conditions, and short setup times of the experimental setup. For this purpose, the experimental setup is presented in this paper. Several series of measurements are presented, showing the characteristics of the generated pressure wave. For the generated pressure wave, the classical pressure curve characteristics can be clearly recognized. A peak pressure of 92 kPa is reached at a distance of 1 m from the opening, and the first positive pressure phase lasts 1.17 ms. Furthermore, the pressure wave propagates in a hemispherical shape. The typical characteristics of the blast wave generated by the SWG have been demonstrated using the military explosive PETN. It is shown that the actual load case corresponds to about 70 g of PETN.
Experimental Setup for the Reproducible Generation of Pressure Waves in Free Field Conditions
(2023)
The injuries caused by the primary blast are still poorly understood, especially in the torso region. To generate sufficiently large data sets, shock tubes are often used. However, these have some limitations, such as blockage, use of the exit jet, widening cross-sections, and scaling problems with respect to compressive strength and test objects. Therefore, it is appropriate to conduct experiments under free-field conditions, but tests with real explosives are often associated with long preparation and setup times as well as high safety requirements.
Therefore, this paper presents an experimental setup for the reproducible generation of blast waves under free-field conditions. This experimental setup aims to provide a test environment for a sufficiently large specimen to investigate the behaviour of the shock wave within the specimen, especially at the media interfaces. As an example of application, the influence of the primary explosive effect on protective equipment or on tissue simulants for the investigation of blast injuries can be mentioned. An autoclave is used as a shock wave generator. It has a volume of 0.065 m3 and is filled with a stoichiometric acetylene-oxygen gas mixture. The setup and turnaround time is approximately 30 minutes. The following factors have been selected as target variables for the optimization of the shock wave generator: reproducibility of the pressure wave, use-case-relevant positive phase duration and peak overpressure, a pressure curve characteristic corresponding to that of a military explosive under undisturbed free field conditions, and short setup times of the experimental setup. For this purpose, the experimental setup is presented in this paper. Several series of measurements are presented, showing the characteristics of the generated pressure wave. For the generated pressure wave, the classical pressure curve characteristics can be clearly recognized. A peak pressure of 92 kPa is reached at a distance of 1 m from the opening, and the first positive pressure phase lasts 1.17 ms. Furthermore, the pressure wave propagates in a hemispherical shape. The typical characteristics of the blast wave generated by the SWG have been demonstrated using the military explosive PETN. It is shown that the actual load case corresponds to about 70 g of PETN.
Im Rahmen dieses Vortrags wurden aktuelle Arbeiten der BAM im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. Den Schwerpunkt des Vortrags bildeten die Auswirkungen der kumulierten Belastung durch "low-level blast" auf das Gehirn von Einsatzkräften und Rückschlüsse für den Arbeitsschutz und die Arbeitsmedizin.
The presented research work examines the effects of different fuel-air equivalence ratios and initial pressure on ignition temperature.
This study shows a non-monotonic pressure dependence in stoichiometric mixtures at varying pressures from 1 to 10 bar and a low sensitivity to changes in the equivalence ratio (0.5-2). The results form the basis for our future research into the complex interaction between lubricant characteristics and hydrogen-air mixtures to better understand pre-ignition phenomena in internal combustion engines.
Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören.
Bei mechanischen Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen.
Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann.
Within a research cooperation between BAM and Gexcon as part of the SH2IFT program, large scale experiments have been performed at the Test Site Technical Safety of the Bundesanstalt für Materialforschung und –prüfung (BAM) to determine the hazards emerging from a vacuum insulated cryogenic storage vessel containing liquified hydrogen (LH2) is caught in a fire engulfing it.