2.1 Sicherheit von Energieträgern
Filtern
Erscheinungsjahr
- 2022 (2)
Dokumenttyp
Sprache
- Englisch (2)
Referierte Publikation
- ja (2)
Schlagworte
- Combustion duration time (2)
- Coal dusts (1)
- Explosion criterion (1)
- Explosion products (1)
- Ignition energy (1)
- Iron dust (1)
- Iron oxides (1)
- Limiting oxygen concentration (1)
- MEC (1)
- Pressure rise rate (1)
Organisationseinheit der BAM
Iron dust explosion characteristics with small amount of nano-sized Fe2O3 and Fe3O4 particles
(2022)
Iron powder, as one of the most abundant metal fuels that can be used as recyclable carriers of clean energy, is a promising alternative to fossil fuels in a future low-carbon economy. It may pose a potential explosion hazard during the process of processing, storage, transport, and reduction/oxidation (redox). The explosion characteristics of iron dust in air were undertaken via a 20 L spherical explosion chamber with an emphasis on minimum explosion concentration (MEC) of iron dust. The alternative method of combustion duration time (tc) was used to determine MEC and compared with the standardized over pressure method. Two kinds of nano-sized iron oxides (Fe2O3 and Fe3O4) were used as inertants to determine the inhibition effect of different oxidation products. The iron dust explosion products with various shapes and sizes were found to be able to grow up 4–6 times of the iron dust for the first time. Adding small amount of Fe2O3 or Fe3O4 could reduce the explosion severity and sensitivity of iron dust. The MEC data determined by both methods were comparable. The addition of 5 % oxide has obvious inhibition effect under 1500 g/m3 concentration. With the increase of oxide concentration to 10 %, the inerting effect increases, and the MEC of iron dust increases more than 3 times. The increase of dust concentration will weaken the inerting effect. When the concentration increases from 500 g/m3 to 3000 g/m3, the weakening effect of 10 % Fe2O3 on the explosion pressure decreases from 38.45 % to 2.24 %, and 10 % Fe3O4 decreases from 46.21 % to 10.63 %. Unlike coal, biomass or aluminum dusts, the iron dust explosion was found to have a unique secondary acceleration of pressure rise rate for the first time. These results provide a fundamental basis to mitigate the iron dust explosion via solid inerting method without adding extra elements.
The explosion characteristics of anthracite and bituminous coals in O2/N2 ambience were experimentally studied via a 20-L spherical explosion chamber with various ignition energies of 2, 5 and 10 kJ. A novel method based on combustion duration time was proposed for the first time, with an emphasis on the determination of the limiting oxygen concentration (LOC). The values of LOC determined by the alternative method were almost consistent with those obtained by using the standardized overpressure method, where the LOCs were above 21.6%, 19.8%, and 13.2% for anthracite coal and 11.4%, 9.6%, and 9.0% for bituminous coal when the ignition energy is 2, 5, and 10 kJ, respectively. But the newly proposed method was found to be much less affected by the ignition energy compared with the standardized overpressure method, taking combustion duration time as an explosion criterion thus had a higher efficiency and required fewer experiments. The results also showed that as oxygen concentration decreases from 21.6% to 14.4%, the maximum explosion pressure decreases from 0.4334 MPa to 0.1034 MPa for anthracite coal and from 0.5664 MPa to 0.3981 MPa for bituminous coal, respectively. Moreover, the effect of ignition energy varied with varying volatile matter content and ignition mechanism of coal dusts. The higher the volatile content, the less sensitive it is to the ignition energy. The newly proposed method will provide a reference for the new standard development, hazard analysis, explosion prevention and suppression by involving the use of inert gases of combustible powder industries.