Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (80)
- Beitrag zu einem Tagungsband (60)
- Vortrag (38)
- Beitrag zu einem Sammelband (26)
- Buchkapitel (3)
- Posterpräsentation (2)
- Forschungsbericht (2)
- Sonstiges (1)
Sprache
- Englisch (212) (entfernen)
Schlagworte
- Wear (47)
- Friction (39)
- Niobium carbide (37)
- NbC (25)
- Slip-rolling (19)
- DLC (16)
- Hardness (13)
- Machining (11)
- Tribology (11)
- Cobalt (10)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (38)
The use of alternative oils for the lubrication of automobile engines has a potential of ecological and technical advantages. It requires the detailed knowledge of several thermophysical and viscometric properties in a large temperature range (mapping). Therefore, the following properties of up to twenty-eight different oils have been measured in the temperature range from 22 °C to 150 °C: density, heat capacity, thermal conductivity, viscosity at ambient pressure, viscosity under shear rates above 10 6 s-1, and the viscosity at elevated pressures (maximum 100 MPa). The last two have been measured with a substantially improved and a newly developed apparatus, respectively. The pressure- viscosity coefficient has been measured on four hydrocarbon-based, factory-fill oils, a paraffin oil and twenty-three alternative oils. Nine of the alternative oils are based partly or completely on esters, the other fourteen on polyglycols, two of them additionally on water.
Englische Übersetzung von BAM Forschungsbericht 237! Keramische Werkstoffe haben auf Grund ihrer herausragenden tribologischen Eigenschaften in verschiedenen Bereichen der Produktion Anwendung gefunden und dadurch klassische Werkstoffe verdrängt. Gegenüber Metallen bieten sie bei Mangelschmierung sowohl unter Gleit- als auch grundsätzlich unter Wälzbeanspruchung Schutz vor adhäsivem Versagen. Hohe Herstellungskosten, bedingt bei der Endbearbeitung von Konturen mit verschiedenen und veränderlichen Radien, behindern die breite Marktdurchdringung. Mit der Modellverschleißprüfung - angelehnt an die DIN 50 324 - kann der bearbeitungsbedingte Einfluss auf das tribologische Verhalten unter Wälzreibung untersucht werden.
Gas turbine efficiency is significantly influenced by the pressure losses caused by the inevitable gap between the rotating turbine blades and the stator parts.
Because contact between rotor and stator cannot be completely avoided with a small gap, systems are designed to allow for some rubbing. Honeycombs or abradable MCrAlY stator coatings are normally used to minimize the wear of the rotor blades when rubbing occurs. But, more efficient solutions must be developed on modern engines, because both suffer temperature limitation and standard MCrAlY have usually poor abradability. For higher temperature and closer control of the gap, a thick thermal-barrier coating must be applied on the stator, but presently with no rub-tolerance.
To increase the abradability of the stator coating, its composition and structure can be modified, but such changes must be strictly limited with respect to the loss of erosion resistance.
The solution can then lie in the hardening of the rotating blade tip to permit the use of harder ceramic or metallic coatings on the stator with greater resistance to erosion. These systems typically consist, on the blade tip, of hard particles embedded in a softer metallic matrix.
In the present programme, it is therefore intended:
- to assess the present European solutions, standard or in development, for outer air seals and blade tips.
- to develop coated grits or new grits for the hardening of the blade tips, as well as to improve the matrix and the stator coating for long life systems.
- to optimize the most promising of these systems, that will be tested on development rigs and on engine.
The consortium includes several engine manufacturers, which are the potential users of the innovating solutions to be developed, companies having a large experience in the field of abradables and tip coatings
and non industrial partners involved in tribology and materials science.
This paper presents the friction and wear behaviour of monolithic titanium-molybdenum carbonitride and tungsten carbide. These materials have been tested sliding against themselves, carbons, fibre reinforced glasses and molybdenum coatings and compared to other ceramics and ceramics composites under unlubricated condition up to 800 °C and 6 m/s.
Self-mated sliding couples of titanium-molybdenum carbonitride display, especially under high-temperature friction, a pronounced wear resistance compared to ceramics and ceramicceramic composites. This very good property is due to the tribo-oxidative formation of so-called lubricious oxides, e.g. Magnéli phases of rutile. They exhibit sliding wear rates under unlubricated friction up to 800 °C as known from mixed/boundary lubrication.
Within the different test conditions, the wear rates of a variety of stationary monolithic materials samples sliding against rotating specimen of (Ti, Mo)(C, N) are always in the group with the lowest wear rates.
The association of the wear resistance, mechanical strength, fracture toughness and low density makes the (Ti, Mo)(C, N) material a complete solution for complex customer demands.
The results presented in this paper have clarified experimentally, that titania-based Magnéli-phases (Ti4O7/Ti5O9 and Ti6O11) with (121)-shear planes exhibit more anti-wear properties than lubricious (low-frictional) properties. The results for dry sliding indicate that the coefficients of friction lie in the range of 0.10.6 depending on sliding speed and ambient temperature. The COF decreased with increasing temperature (T= 22800°C) and increasing sliding speed (?= 1-6 m/s). The dry sliding wear rate was lowest for the Al2O3 at 1 m/s at 800°C with values of 1.7 × 10-8 and 6.4 × 10-8 mm3/N m, comparable to boundary/mixed lubrication, associated with a high dry frictional power loss of 30 W/mm2. The running-in wear length and, more important, the wear rate decreased under oscillating sliding tests with increasing relative humidity. The contact pressure for high-/low-wear transition increased under oscillating sliding tests with increasing relative humidity. At room temperature and a relative humidity of 100% the steady-state wear rate under dry oscillating sliding for the couple Al2O3/Ti4O7Ti5O9 was lower than 2 × 10-7 mm3/N m and therefore inferior to the resolution of the continuous wear measurement sensor. TEM of wear tracks from oscillating sliding revealed at room temperature a work-hardening as mechanism to explain the running-in behavior and the high wear resistance. The hydroxylation of titania surfaces favours the high-/low-wear transition.