Filtern
Erscheinungsjahr
- 2012 (19) (entfernen)
Dokumenttyp
- Vortrag (7)
- Beitrag zu einem Tagungsband (6)
- Zeitschriftenartikel (4)
- Buchkapitel (1)
- Beitrag zu einem Sammelband (1)
Sprache
- Deutsch (9)
- Englisch (7)
- Französisch (2)
- Mehrsprachig (1)
Schlagworte
- Slip-rolling (4)
- DLC (3)
- Dünnschichten (2)
- Extrembeanspruchung (2)
- Friction (2)
- Thin film coatings (2)
- ta-C (2)
- 100Cr6 (1)
- ASP20212 (1)
- Additive (1)
Eingeladener Vortrag
- nein (7)
Nullverschleiß
(2012)
The slip-rolling resistances of hard and stiff thin films under high Hertzian contact pressures can be improved by optimizing the 'coating/substrate systems'. It is known from former investigations that the so-called 'egg-shell' effect is no general hindrance for high slip-rolling resistance of thin hard coatings. The coating stability depends more on specific deposition process and coating/substrate interface design. In this article it is experimentally shown, that pure amorphous carbon thin films with hardness between 15 and 63 GPa can be slip-rolling resistant several million load cycles under a maximum Hertzian contact pressures of up to 3.0 GPa. Whereas all coatings were stable up to 10 million load cycles in paraffin oil at room temperature, reduced coating lifetime was found in SAE 0W-30 engine oil at 120°C. It was shown how the coating hardness and the initial coating surface roughness influence the running-in process and coating lifetime. No clear correlation between coating hardness and coating lifetime could be observed, but friction coefficients seem to be reduced with higher coating hardness. Very low friction down to ~0.03 in unmodified engine oils was found for the hardest ta-C film.------------------------------------------------------------------------------------------------------------------------------------------------
Die Wälzbeständigkeit von harten und steifen Dünnschichten unter hohen Hertzschen Kontaktpressungen kann durch die Optimierung des 'Beschichtung/Substrat Systems' deutlich verbessert werden. Aus vorangegangenen Untersuchungen ist bekannt, dass der so genannte 'Eierschaleneffekt' kein generelles Hindernis für eine hohe Wälzbeständigkeit für harte Dünnschichten darstellen muss. Die Stabilität der Beschichtungen hängt vielmehr von dem spezifischen Prozessparametern und dem Schicht/Substrat Grenzflächendesign ab. In diesem Artikel wird experimentell nachgewiesen, dass reine amorphe Kohlenstoffdünnschichten mit Härtewerten zwischen 15 und 63 GPa für mehrere Millionen Lastzyklen unter maximalen Hertzschen Kontaktpressungen bis 3.0 GPa überrollbeständig sein können. Während alle Beschichtungen bis 10 Millionen Lastzyklen in Paraffinöl bei Raumtemperatur keine Defekte aufweisen wurde unter Verwendung eines SAE 0W-30 Motorenöls bei 120°C eine Verringerung der Überrollbeständigkeit nachgewiesen. Es wurde nachgewiesen, wie die Schichthärte und ursprüngliche Oberflächenrauheit der Beschichtung den Einlaufprozess und die Lebensdauer beeinflussen. Es konnte keine offensichtliche Korrelation zwischen Schichthärte und Lebensdauer festgestellt werden, allerdings wurde eine scheinbare Reduktion des Reibwertes mit steigender Schichthärte beobachtet werden. Dabei zeigte die härteste ta-C Schicht unter Verwendung des Motorenöls sehr geringe Reibwerte mit ~0.03.
Zero wear (Null Verschleiß)
(2012)
Recent developments in contact mechanics and microfribology have shown that it is very important to study surface modification effects for quantification of „Zero wear“ (plastic deformation of upper parts of asperities) during sliding friction. The present work considers experimental and Simulation data on the Formation of elastic and plastic contact areas during sliding friction on rough surfaces. The Simulation of discrete contact was carried out using as a source the AFMimages of real surface topography at micro/nanoscale.
The approach for quantification of „zero wear“, proposed here, is not using common Statistical Parameters of roughness, but it considers contact areas on asperities.
In these areas some regions are undergoing plastic deformation which influences surface Transformation during sliding friction. Also, the workhardening effect was taken into account in the Simulation
of sliding friction. This enabled a rnore successful fit of experimental data. The results obtained of the Computer simulations will provide a way of studying friction force at the initial stage of the running-in process.
Downsizing (power-to-weight ratio) and higher speeds lead to a rise in Hertzian contact pressures in combination with an increase in surface or oil temperatures. Under such conditions, commonly used bearing steels, such as 100Cr6, reach their limits, creating a demand for alternative slip-rolling resistant steel alloys. The present work therefore compares the slip-rolling performance of various steel types with Maraging- and PM-type steel alloys such as e.g. CSS-42L™, ASP2012, BIMAX42+, in the Hertzian contact pressure range up to P0max of 4 GPa. Through-hardened 100Cr6H (AISI 52100), case-hardened 20MnCr5 (AISI 5120H) and nitrogen alloyed Croni-dur30 (AMS 5898) still compete in terms of slip-rolling and wear resistance and load carrying capacity, whereas Maraging- and PM-type steel alloys offer superior strength and toughness properties.