Filtern
Dokumenttyp
Sprache
- Englisch (16)
- Deutsch (9)
- Französisch (3)
Schlagworte
- DLC (28) (entfernen)
Paraffinöl geschmierte Wälztests wurden an extrem harten Diamantschichten auf hartem SSiC Substrat, unterschiedlichen, harten DLC-Schichten auf 100Cr6 Substraten (HRC60) sowie ausgewählten DLC-Schichten auf ungehärtetem Stahl (HRC 20) durchgeführt. Die Wälztests wurden in einem Zweischeibentribometer vom Typ Amsler bei einer anfänglichen, maximalen Flächenpressung nach Hertz von P0=2,3 GPa ausgeführt. Als Abbruchkriterium für die Tests wurde das Erreichen von n=1.000.000 Überrollungen (Langzeittests n=10.000.000 Überrollungen) oder das Auftreten einer Schädigung mit einer zusammenhängenden Fläche von A>1 mm2 festgelegt. Die Wälztests zeigten, dass das harte SSiC Substrat zwar eine stützende Wirkung auf die Diamantschicht hat, diese aber aufgrund von Rissen im Substrat versagte. Ferner gibt es wenigstens zwei DLC-Schichten, die, aufgebracht auf 100Cr6 Scheiben (HRC60), den Wälztests bis n=10.000.000 Überrollungen ohne nennenswerte Schäden widerstanden. Diese Schichten passten sich auch den Verformungen des weichen, stickstofflegierten Stahls (HRC20) an, ohne das es zu größeren Abplatzungen kam (A>1 mm2).
OEMs perceive diamond-like carbon (DLC) coatings as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gears and engines. In previous investigations it was shown, that DLC, amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings can be slip-rolling resistant at least up to ten million load cycles at Hertzian contact pressures P0max of 2.9 GPa lubricated by engine oil at 120°C, Further improvements in load carrying capacity up to P0mean of 2.62 GPa (FN= 5,000 N) were achieved with alternative, available Steel metallurgies as Substrates for thin film coatings. Additional factors, such as influences of the lubrication on the surface chemistry (additives and base oils), wear and friction behavior were investigated.
Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz’schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden, in der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis Pomax = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei +120°C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt.
The dilution of biogenic fuels into lubricating engine oils often leads to a shortening of the recommended oil drains (between 30% and 60%) and an increase in wear. The large number of overlapping and influencing factors, of which dilution and polymerization of fuel components in the engine oil are emphasised, makes it difficult to find a uniform solution to prevent failures in the various applications.
Insofar single solutions for the different types of biofuels are needed. The contribution of base oil chemistry and additives as well as triboactive materials is featured to deal with the adverse effects of biofuels. In the frame of the European Commission (EC)-funded project 'cleanengine', tentative engine oils based on esters with a content of renewables and polyglycols are formulated to increase the lubricant's tolerance in engines fuelled with biofuel-based blends, with the aim of ensuring required lubricating and wear protection performance while keeping oil drain intervals unchanged.
The present paper focuses on four-stroke diesel applications, fuelled by biodiesel (fatty acid methyl ester — FAME) as well as by rapeseed oil and Jatropha oil (pure vegetable oils, triglycerides), together with relevant blends of those biofuels and conventional diesel fuel.
This paper screens the functional profile (in particular rheological, toxicological, bio-compatibility, tribological and biofuels affinity) of lube families with respect to biofuel contamination. Moreover, this is followed by the contributions of piston ring and liner materials as well as thin film coatings.
Costs reduction is one of the major objectives in mechanical applications with a parallel increase of the power output. Another driver represents new environmental standards and their increasing restrictions in the automotive industry leading to the question, if materials based concepts may substitute harmful EP/AW additives in lubricants. This paper presents the slip-rolling resistance of different DLC/THC coatings on steel substrates with a definite slip rate of 10%. Industrial DLC coatings of ta-C and a-C:H types from various manufacturers were deposited on steels SAE 52100 and AMS 5898 to compile the slip-rolling resistance under initial average Hertzian contact pressures between 1.5 GPa and 2 GPa. The tests were carried out on Amsler-type twin disc tribometer under the regime of mixed/boundary lubrication in unadditivated paraffinic oil (ISO VG 46) and a factory fill engine oil. The spherical steel sample was uncoated and the cylindrical coated with DLC. Some coatings achieved 10 million cycles without any damage under a maximal Hertzian contact pressure Pmax well over 2.25 GPa, thus exceeding FZG 12.
Zero wear (Null Verschleiß)
(2013)
Highly concentrated or loaded contacts in powertrain and gear applications offer significant weight savings in C02 emissions. Today, thin film coatings, alternative base oils and new additives are populär as working fields and strategies of OEMs to realize low friction tribosystems. Especially the automotive industry anticipates environmental and performance benefits in applying light-weight construction of mechanical parts, for instance in gears and engines. Light-weight strategies increase the contact stresses above 2.14 GPa (or FZG load stage 14) due to the reduction of component sizes. These demands directly raise questions about the suitability of the most promising technical solution. Alternative steels with improved mechanical properties, i.e. toughness values, which offer low coefficients of friction, optimal resistance to high contact pressure and potential to apply low friction surface coatings representing a valid alternative to conventional gear steels. Traditional bearing and gear steels, such as 100Cr6 (SAE E52100) or 16MnCr5 (1.7131) have reached their mechanical limits at contact pressures above FZG load stage 14.
Nowadays, diamond-like carbon (DLC) coatings are mainly used in many low loaded applications such as in machine tools, computer devices and many more.
Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gear components.
The ulterior motive is a global performance increase regarding environmental impact and power efficiency.
In recent years, the slip-rolling resistance of DLC, a-C and ta-C thin film coatings was improved considerably.
In view of the mechanical application of thin film coatings, there is still room for improvements.
It was experimentally shown, that a-C and ta-C coatings can be slip-rolling resistant at room temperature in unaddivated paraffin oil up to ten million cycles under Hertzian contact pressures up to P0max = 2.9 GPa.
Typically, the prime coated steel substrates were made of the hardened and tempered steels 100Cr6H and Cronidur 30.
The aim of the work this to overtake these results, i.e. at higher maximum Hertzian pressures up to P0max = 4.2 GPa.
Under such extreme conditions, it is necessary to choose special steels to avoid the failure of the substrate and to permit a higher load carrying capacity of the coating-substrate-system.
In consideration of the increased substrate properties, two high toughness spring steels and an ultra-high toughness aerospace steel were tested on a twin disc tribometer of the Amsler type as well as on an Optimol TwinDisc test rig under mixed/boundary conditions.
Different factors such as residual stresses of the substrate, influences of the lubrication, and wear behaviour were investigated.
The respective results are presented here.
The slip-rolling resistance of DLC, a-C and ta-C thin film coatings was improved considerably in the last years, but there is still room for improvements in relation to (a) the temperature stability and (b) initial surface roughness after deposition. This paper presents a novel coating-substrate system in comparison to recently developed DLC coatings in a bench-mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. One of the Zr-based thin film coatings can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions or ten million of cycles under P0max = 2940 MPa. In comparison, some of the newly developed DLC coatings are slip-rolling resistant for at least up to 10 million cycles at RT (some of them also at 120 °C oil temperature) under Hertzian contact pressures of Pmax = 2600/2940 MPa. In general, Zr-based thin film coatings do not require special formulated oil formulations and Zr(C,N) bear on a straight coating architecture suited for mass production with nanosized layers.
The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of high-performance coatings represents one approach among others. This paper presents some recently developed DLC coatings (a-C:H and ta-C) as well as a novel coating-substrate system (Zr(C,N)) in a benchmark test procedure under slip-rolling conditions in the presence of liquid lubricants. Various coatings with different thickness, interlayer and substrates were evaluated for their slip-rolling resistance in different lubricants at ambient temperature and at 120 °C. Results indicate that some of these coating systems can withstand at least 10 million cycles under initial Hertzian contact pressures of up to Pmax = 3.500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. Surface of the coatings and the counter bodies were analysed and compared with untreated substrates.
Wälzbeständigkeit von ta-C Dünnschichten unter hohen Hertzschen Beanspruchungen bis zu 3000 MPa
(2010)
Zirkonium-basierte Dünnschichten in hochbeanspruchten Wälzkontakten als Alternative zu DLC und ta-C
(2009)
Coatings for slip-rolling
(2014)
Original equipment manufacturers (OEMs) and end-users perceive 'Zero Wear' differently. The 'Zero Wear' approach will be put into a general relation for different applications and illuminated by individual paths, either based on monolithic materials, thin film coatings or alternative base oils, featuring triboactive materials and lubricious oxides for tribological engine components and dry running foil bearings or specific DLC, ta-C and novel Zirconium-based thin film coatings for concentrated contacts above FZG 14 and alternative engine oils (NoSAP & bio-no-tox). The associated tribometric test equipments for these examples will also be detailed.
Le secteur automobile doit faire face actuellement à de nouveaux challenges au niveau de la construction allégée, des économies de carburant et des coûts. Ces exigences motivent la mise au point de tribosystèmes pouvant résister à des pressions de contact de plus en plus élevées avec de faibles coefficients de frottement. L'optimisation de systèmes existants par l'application de revêtements de surface performants représente une alternative intéressante. Ce texte présente les performances de couches minces dans des conditions d'essais de slip-rolling (roulement à composante de glissement) en présence de lubrifiants liquides. Après une première sélection à température ambiante, les revêtements les plus performants ont été testés à 120 °C. Il s'agit de revêtements DLC en carbone hydrogéné (a-C:H) et en carbone tétraédrique (ta-C) de dernières générations ainsi qu'un nouveau système « revêtement/substrat ». Certains des revêtements DLC développés récemment sont résistants en slip-rolling au moins jusq'à 10 millions de cycles à 120 °C dans l'huile moteur sous des pressions hertziennes de contact de P0max = 2600 / 2940 MPa. De plus, le nouveau système revêtement Zr(C,N)x/substrat peut résister au moins à 1 million de cycles sous des pressions hertziennes initiales de contact allant jusqu'à P0max = 3500 MPa et à des températures de lubrifiant d'au moins 120 °C. -----------------------------------------------------------------------------------------------------------------------------------------------
The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of surface coatings represents one approach among others. This paper presents thin film coatings performances in a bench mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. After a first selection at room temperature, the most resistant coatings were evaluated at 120 °C. These are newly developed DLC coatings (a-C:H & ta-C) as well as a novel coating-substrate system. Some of the newly developed DLC-coatings are slip-rolling resistant for at least up to 10 million cycles at 120 °C oil temperature) under Hertzian contact pressures of P0max = 2600 / 2940 MPa. Furthermore, this novel Zr-based thin film coating can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions.
Diamond-like carbon (DLC) coatings are perceived as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gear and engine components. Therefore, in previous investigations amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings were inspected. For up to ten million cycles at Hertzian contact pressures P0max of 2.9 GPa it was shown that these coatings are slip-rolling resistant not only at room temperature in the presence of unaddivated paraffin oil, but also up to 120 °C oil temperature. The steel substrates in this investigation were made of the hardened and tempered steels 100Cr6H and Cronidur 30. The aim of the current work is manifold. The Hertzian contact pressures should be increased up to P0max of 4.2 GPa by using new steel metallurgies as substrates for thin film coatings. These steel metallurgies are also assessed, if they can compete as uncoated couples. Two high toughness spring steels and an ultra-high toughness aerospace steel were tested in a twin disc tribometer of the Amsler type as well as in an Optimol 2Disk test rig under mixed/boundary conditions in a factory fill SAE 0W-30 engine oil. Different factors such as influences of the lubrication, surface chemistry and wear behaviour were investigated.
Some of the properties intrinsically present in the backbone of polyalkylene glycols (PAGs), which have nowadays attracted the automotive original equipment manufacturers (OEMs), are presented, such as bio-no-tox properties, heat capacity, extended drains, low friction, low AlSi-liner wear, fuel economy, and very high viscosity indices, and are achieved with metal-, ash-, and polymer-free formulations, which guarantee no adverse contamination of the lambda sensor and the active centers of the catalyzer as well as not to increase the exhaust back pressure of the particulate filter through ash deposits. This paper illuminates the latest results from OEM's engine bench and road testing supporting the following functional benefits: (a) bio-no-tox, (b) improvements of fuel economy, even when compared with latest hydrocarbon-based prototype oils, (c) reduced wear, (d) reduced engine friction, (e) extended drains, (f) suited for bio-fuels, (g) no adverse effects on after-treatment devices through ash-, metal-, and polymer-free formulations, etc.