Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (23)
- Beitrag zu einem Sammelband (8)
- Beitrag zu einem Tagungsband (7)
- Buchkapitel (1)
- Sonstiges (1)
Sprache
- Englisch (23)
- Deutsch (15)
- Französisch (2)
Schlagworte
- DLC (14)
- Slip-rolling (8)
- Wear (8)
- Friction (6)
- Wälzen (5)
- ZrCN (5)
- Dünnschichten (3)
- Extrembeanspruchung (3)
- Hochzähe Stähle (3)
- Simulation (3)
Organisationseinheit der BAM
Der Einfluss des E-Moduls und des Grundöls auf das Wälzverhalten von DLC- und Diamantbeschichtungen
(2004)
In situ Acoustic Emission for wear life detection of DLC coatings during slip-rolling friction
(2006)
Different diamond-like carbon (DLC) coatings on a steel substrate (100Cr6) were tested under slip-rolling friction conditions against uncoated counter bodies of the same steel. The initial maximum Hertzian pressure was varied in a range of P0 = 1.52.3 GPa. The friction tests were carried out under dry conditions and with an unadditivated paraffin oil as lubricant. It could be shown that the thickness of the coatings affects the respective wear life. Further, a very important factor for the wear life of a coating under lubricated slip-rolling conditions is the roughness of the surface of the respective counterbody. The wear life tests were monitored by recording in situ the Acoustic Emission (AE) signals. Some causes for a high AE activity could be identified.
Paraffinöl geschmierte Wälztests wurden an extrem harten Diamantschichten auf hartem SSiC Substrat, unterschiedlichen, harten DLC-Schichten auf 100Cr6 Substraten (HRC60) sowie ausgewählten DLC-Schichten auf ungehärtetem Stahl (HRC 20) durchgeführt. Die Wälztests wurden in einem Zweischeibentribometer vom Typ Amsler bei einer anfänglichen, maximalen Flächenpressung nach Hertz von P0=2,3 GPa ausgeführt. Als Abbruchkriterium für die Tests wurde das Erreichen von n=1.000.000 Überrollungen (Langzeittests n=10.000.000 Überrollungen) oder das Auftreten einer Schädigung mit einer zusammenhängenden Fläche von A>1 mm2 festgelegt. Die Wälztests zeigten, dass das harte SSiC Substrat zwar eine stützende Wirkung auf die Diamantschicht hat, diese aber aufgrund von Rissen im Substrat versagte. Ferner gibt es wenigstens zwei DLC-Schichten, die, aufgebracht auf 100Cr6 Scheiben (HRC60), den Wälztests bis n=10.000.000 Überrollungen ohne nennenswerte Schäden widerstanden. Diese Schichten passten sich auch den Verformungen des weichen, stickstofflegierten Stahls (HRC20) an, ohne das es zu größeren Abplatzungen kam (A>1 mm2).
Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz’schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden, in der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis Pomax = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei +120°C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt.
Einfluss der Topographie von DLC-Schichten auf deren Verhalten unter geschmierter Wälzbeanspruchung
(2004)
A novel tribometer has been designed using commercially available components for sliding motion at 40kHz with amplitude between 2.5 and 5µm. The tribometer is equipped with means to measure amplitude, frequency, power required to keep the sample in motion and load applied. The effective motion between the two contacting bodies is monitored. These data are used to evaluate the coefficient of friction. The wear rate was determined after the tests. The set-up was tested using novel, non-commercial substrates such as AlFeCrTi-alloys and tungsten carbide-based coatings as well as Magnéli-type coatings (Tin-2Cr2O2n-1 and TinO2n-1). This paper presents the principle of the ultra-high frequency tribometer and first tribological quantities of materials and coatings tested.
Diamond like carbon (DLC)-coatings are applied very successfully on computer discs. Sliding friction tests confirm their high performance as dry lubricants with friction coefficients (COFs) below 0.1. In contrast to sliding tests, until very recently most of the DLC-coatings failed in slip-rolling test after fewer cycles than uncoated samples. However, present tests with DLC-coatings of seven different suppliers show a more promising tribological behaviour under slip-rolling conditions. The DLC-coatings were deposited onto steel 100Cr6, HRC 60, with a thickness of 23 ?m. The counter bodies were uncoated, grinded or polished 100Cr6 discs with 30 mm radius of curvature. The tests were performed on a twin disc testing rig (Amsler type) with paraffin oil under boundary/mixed lubrication and rolling with 10% slip. The initial, average Hertzian contact pressure was adjusted to Pm = 1.0, 1.25, and 1.5 GPa. The failure criterion was defined as the occurrence of a single damaged area larger than 1 mm2, which was controlled by optical microscopy (OM). An acoustic emission (AE) measurement system was installed as an additional online control for coating failure. The stressed coatings and the chipping areas were analyzed by OM, SEM, EDX, AFM and Raman spectroscopy.
Until now, the results reveal that a large scatter in lifetime of coatings occurs not only between samples of different coaters but also between the samples of one single batch. The highest lifetime reached by a DLC-coating under these testing conditions is 10 × 106 cycles. That is the highest life time for a coating tested under the testing conditions above in our laboratory so far. The following factors were identified to influence the life time of the coatings: coating thickness, interlayer type, topography of the coatings, counter body roughness and mechanical properties. But the most important factor determining the life time of the coatings is that the coating process does produce homogenous layers free of faults.
Costs reduction is one of the major objectives in mechanical applications with a parallel increase of the power output. Another driver represents new environmental standards and their increasing restrictions in the automotive industry leading to the question, if materials based concepts may substitute harmful EP/AW additives in lubricants. This paper presents the slip-rolling resistance of different DLC/THC coatings on steel substrates with a definite slip rate of 10%. Industrial DLC coatings of ta-C and a-C:H types from various manufacturers were deposited on steels SAE 52100 and AMS 5898 to compile the slip-rolling resistance under initial average Hertzian contact pressures between 1.5 GPa and 2 GPa. The tests were carried out on Amsler-type twin disc tribometer under the regime of mixed/boundary lubrication in unadditivated paraffinic oil (ISO VG 46) and a factory fill engine oil. The spherical steel sample was uncoated and the cylindrical coated with DLC. Some coatings achieved 10 million cycles without any damage under a maximal Hertzian contact pressure Pmax well over 2.25 GPa, thus exceeding FZG 12.
High-power piezo-electric motors with power densities of 1.4 kW/kg display a potential for substituting hydraulic actuators. For this application, two novel tribometers of the same type have been designed using commercially available components for sliding motion at 40 kHz with amplitudes between 2.5 µm and 5 µm. The tribometers are equipped with means to measure amplitude, frequency, power required to keep the samples in motion and load applied. The effective motion between the two contacting bodies is monitored in each of the tribometers. These data are used to evaluate the coefficient of friction. The wear rate was determined after the tests. The set-ups were tested using well-known 100Cr6H (AISI 52100) samples before investigating novel, non-commercial substrates such as AlFeCrTi-alloys and tungsten carbide-based coatings as well as Magnéli-type coatings (Tin-2Cr2O2n-1 and TinO2n-1). This paper presents the principle of the ultra-high frequency tribometers and first tribological quantities of materials and coatings tested up to and above 1011 cycles. Very low wear rates in the range 10-8 mm³/Nm down to 10-10 mm³/Nm were determined under dry oscillation in air.
Der Einfluss des E-Moduls und des Grundöls auf das Wälzverhalten von DLC- und Diamantbeschichtungen
(2005)
Zero wear (Null Verschleiß)
(2013)
The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of high-performance coatings represents one approach among others. This paper presents some recently developed DLC coatings (a-C:H and ta-C) as well as a novel coating-substrate system (Zr(C,N)) in a benchmark test procedure under slip-rolling conditions in the presence of liquid lubricants. Various coatings with different thickness, interlayer and substrates were evaluated for their slip-rolling resistance in different lubricants at ambient temperature and at 120 °C. Results indicate that some of these coating systems can withstand at least 10 million cycles under initial Hertzian contact pressures of up to Pmax = 3.500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. Surface of the coatings and the counter bodies were analysed and compared with untreated substrates.
Zero wear (Null Verschleiß)
(2012)
Recent developments in contact mechanics and microfribology have shown that it is very important to study surface modification effects for quantification of „Zero wear“ (plastic deformation of upper parts of asperities) during sliding friction. The present work considers experimental and Simulation data on the Formation of elastic and plastic contact areas during sliding friction on rough surfaces. The Simulation of discrete contact was carried out using as a source the AFMimages of real surface topography at micro/nanoscale.
The approach for quantification of „zero wear“, proposed here, is not using common Statistical Parameters of roughness, but it considers contact areas on asperities.
In these areas some regions are undergoing plastic deformation which influences surface Transformation during sliding friction. Also, the workhardening effect was taken into account in the Simulation
of sliding friction. This enabled a rnore successful fit of experimental data. The results obtained of the Computer simulations will provide a way of studying friction force at the initial stage of the running-in process.
Downsizing (power-to-weight ratio) and higher speeds lead to a rise in Hertzian contact pressures in combination with an increase in surface or oil temperatures. Under such conditions, commonly used bearing steels, such as 100Cr6, reach their limits, creating a demand for alternative slip-rolling resistant steel alloys. The present work therefore compares the slip-rolling performance of various steel types with Maraging- and PM-type steel alloys such as e.g. CSS-42L™, ASP2012, BIMAX42+, in the Hertzian contact pressure range up to P0max of 4 GPa. Through-hardened 100Cr6H (AISI 52100), case-hardened 20MnCr5 (AISI 5120H) and nitrogen alloyed Croni-dur30 (AMS 5898) still compete in terms of slip-rolling and wear resistance and load carrying capacity, whereas Maraging- and PM-type steel alloys offer superior strength and toughness properties.
Coatings for slip-rolling
(2014)
We review contact mechanics with emphasis on the rheological (time dependent) properties of polymers and their relations to surface roughness, material properties, and friction as well as wear behavior of rubbing polymer surfaces. The main concept of polymer mechanics related to tribology consists of three basic elements involved in friction: deformation resulting in the real area of contact of rough surfaces, contact adhesion, and shear and rupture of materials in the contact during the sliding friction. The results of classical work are included, which addresses the real contact area calculation and the description of adhesion interaction between rough surfaces. A brief review of experimental investigations concerning the surface characterization by means of bearing curves, the intermolecular force interaction using the adhesion parameter, the effect of temperature on the real contact area, the formation of transferred polymer film during friction, and tribological behavior of ultrathin polymer layers are presented and their implications discussed.
Le secteur automobile doit faire face actuellement à de nouveaux challenges au niveau de la construction allégée, des économies de carburant et des coûts. Ces exigences motivent la mise au point de tribosystèmes pouvant résister à des pressions de contact de plus en plus élevées avec de faibles coefficients de frottement. L'optimisation de systèmes existants par l'application de revêtements de surface performants représente une alternative intéressante. Ce texte présente les performances de couches minces dans des conditions d'essais de slip-rolling (roulement à composante de glissement) en présence de lubrifiants liquides. Après une première sélection à température ambiante, les revêtements les plus performants ont été testés à 120 °C. Il s'agit de revêtements DLC en carbone hydrogéné (a-C:H) et en carbone tétraédrique (ta-C) de dernières générations ainsi qu'un nouveau système « revêtement/substrat ». Certains des revêtements DLC développés récemment sont résistants en slip-rolling au moins jusq'à 10 millions de cycles à 120 °C dans l'huile moteur sous des pressions hertziennes de contact de P0max = 2600 / 2940 MPa. De plus, le nouveau système revêtement Zr(C,N)x/substrat peut résister au moins à 1 million de cycles sous des pressions hertziennes initiales de contact allant jusqu'à P0max = 3500 MPa et à des températures de lubrifiant d'au moins 120 °C. -----------------------------------------------------------------------------------------------------------------------------------------------
The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of surface coatings represents one approach among others. This paper presents thin film coatings performances in a bench mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. After a first selection at room temperature, the most resistant coatings were evaluated at 120 °C. These are newly developed DLC coatings (a-C:H & ta-C) as well as a novel coating-substrate system. Some of the newly developed DLC-coatings are slip-rolling resistant for at least up to 10 million cycles at 120 °C oil temperature) under Hertzian contact pressures of P0max = 2600 / 2940 MPa. Furthermore, this novel Zr-based thin film coating can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions.
JATROPHA - The Seed of Energy - CO2-Neutral Fuels and Lubricants Based on Sustainable Non-Food Oils
(2009)
Diamond-like carbon (DLC) coatings are perceived as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gear and engine components. Therefore, in previous investigations amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings were inspected. For up to ten million cycles at Hertzian contact pressures P0max of 2.9 GPa it was shown that these coatings are slip-rolling resistant not only at room temperature in the presence of unaddivated paraffin oil, but also up to 120 °C oil temperature. The steel substrates in this investigation were made of the hardened and tempered steels 100Cr6H and Cronidur 30. The aim of the current work is manifold. The Hertzian contact pressures should be increased up to P0max of 4.2 GPa by using new steel metallurgies as substrates for thin film coatings. These steel metallurgies are also assessed, if they can compete as uncoated couples. Two high toughness spring steels and an ultra-high toughness aerospace steel were tested in a twin disc tribometer of the Amsler type as well as in an Optimol 2Disk test rig under mixed/boundary conditions in a factory fill SAE 0W-30 engine oil. Different factors such as influences of the lubrication, surface chemistry and wear behaviour were investigated.
A correlation of adhesion force and electrical conductivity is established for a vanadium oxide and highly oriented pyrolytic graphite (HOPG). Adhesion forces were determined by analysis of pull-off forces obtained from force–distance curves with atomic force microscopy in ultrahigh vacuum, on clean surfaces and with defined contact conditions. The investigated samples include (i) different stoichiometries of Magnéli-type vanadium oxides (V3O5, V4O7, V6O11, and V7O13), which undergo metal-insulator-transitions as a function of temperature, (ii) the (0001) basal plane and the (10–10) prism plane of highly oriented pyrolytic graphite (HOPG), which differ in their respective perpendicular-plane electrical conductivities by several orders of magnitude, and (iii) the (100) surfaces of pure metal single crystals, i.e., silver (Ag), copper (Cu), iron (Fe) and gold (Au). It is shown, that the vanadium oxides as well as the graphite exhibit significantly lower adhesion forces in their electrical conductive state than in their non-electrical conductive state. The values obtained for the electrical conductive states are quantitatively confirmed by the measurements on the single crystal metals.
In the present work an approach is presented which combines various aspects of the former models with probability considerations. It is used to simulate the impact of more than one billion Alumina particles onto a steel substrate. This approach permits the simulation of an entire erosion experiment on an average PC within about six hours.
This paper shows how Angle-Resolved Scattering can reveal wear on engineered surfaces. The samples studied, three discs made of steel 100Cr6H used in gear wheels in the automotive industry, were assessed after they had undergone ball-on-disc tests. Scattering maps recorded for spatial frequencies from 0.1 µm-1 to 2.7 µm-1 show a contrast inversion around 0.36 µm-1 revealing the wear trace. Besides measurements of rms roughness, where mean values are 20 nm and 24 nm depending on the locations considered, stationarity and isotropy, we demonstrate the ability of the technique to reveal localized wear on this type of surface in a rapid, robust and convenient way. We show that the tool trace is influenced by the load magnitude rather than by the number of oscillation cycles and highlight the key role played by surface roughness in how the sample responds to wear tests.
The aim of this research is to characterize a surface that has experienced low wear on asperities. The procedure used is similar to an Abbott-Firestone approach and based on functional bearing of projected area, surface area and material volume. Surface features extracted from surface height maps provide more comprehensive information about topography changes due to wear. Thus, they were used to detect low wear volumes on the top of asperities.
The cause and type of solid particle erosion varies across different industries and locations in plants, for instance the particles could be volcanic ash in aero-engines, fly ash in boilers, exfoliated scale in steam turbines or mineral matter in oil excavation. In all cases the durability of materials can be improved through better surface engineering and coatings, but the development of these is restricted also due to lack of generic models. In this respect, the simulation of a single impact with finite element methods using 100.000 knots would take about 15 minutes. In order to simulate an entire particle erosion experiment, up to one billion of such impacts would have to be considered. In order to simulate an entire particle erosion experiment, the current work presents an alternative approach capable of calculating about half a billion impacts on a substrate in less than six hours on a standard PC. The predictions of the simulation will be compared to a steel sample at 600°C eroded by aluminum oxide particles with a velocity around 210 m/s.