Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (22) (entfernen)
Schlagworte
- Friction (6)
- Vacuum (6)
- Graphite (4)
- Hydrogen environment (4)
- Tribologie (4)
- Wear (4)
- Festschmierstoffe (3)
- Kompositwerkstoffe (3)
- Polymer composites (3)
- Vakuum (3)
Organisationseinheit der BAM
This paper presents investigations on the tribological behaviour of PTFE composites against steel at cryogenic temperatures. The results showed that the friction coefficient decreases with temperature down to 77 K, but did not follow a linear evolution further down to extreme low temperatures. It can be stated that the cryogenic environment has a significant influence on the tribological performance of the polymer composites. The effect of low temperatures was more clearly detected at low sliding speed, where friction heat is reduced. A change in wear mechanism from adhesive to abrasive was observed in this case. SEM and AFM analyses showed that the PTFE matrix composites investigated under these experimental conditions have transferred material onto the disc down to very low temperatures. Chemical analyses indicate the presence of iron fluorides.
The tribological behaviour of MoS2/ta-C double layer coatings deposited by Laser-Arc technology was investigated in vacuum and air. In vacuum environment, the friction coefficient against steel balls varies between 0.005 and 0.02 depending on the contact pressure. At high contact pressures, the friction coefficient is as low as 0.005 and the life time between 340,000 and 500,000 cycles. Furthermore, it is shown that a ta-C base layer improves the performance of MoS2 coating.
Surface analyses were performed before and after the tribological tests by means of SEM, EDX, XRD, and TEM. They show that in the top layer beneath the sliding surface crystallization of the initially quasi-amorphous MoS2 took place. TEM images also verified an orientation of the basal MoS2-lattice planes parallel to the surface.
This paper presents the mechanical and tribological properties of
Polytetrafluoroethylene (PTFE) and Polyetheretherketone (PEEK)
matrix composites filled with short carbon fibers in cryogenic
environments. Tensile tests were performed at room temperature (RT)
in air and in LN2. Tribological experiments were carried out with a
pin-on-disc configuration at RT, in LN2, in LH2 and in LHe. PEEK
composites have a better tribological performance than PTFE materials
especially regarding the wear resistance.
For tribological components working under extreme
conditions, such as vacuum, or broad temperature
ranges, it is often a problem to achieve acceptable
durability of their friction parts. Thus, new material
requirements are involved for these tribo-systems, in
particular regarding operability and reliability. At BAM,
several projects were conducted in the recent years,
dealing with the tribological properties of friction
couples at cryogenic temperature and in vacuum
environment. This paper describes the vacuum and ultra
high vacuum tribometers constructed at BAM and
presents experiments carried out with polymer
composites. The experiments presented were performed
with PEEK, filled with solid lubricants, against 304
steel with a pin-on-disc configuration in oscillating
sliding. Friction tests were carried out in vacuum in the
temperature range between -40°C and +160°C and in
ultra high vacuum at room temperature.
Influence of the Temperature on the Tribological Behaviour of PEEK Composites in Vacuum Environment
(2008)
This paper describes tribological experiments carried out with polyetheretherketone (PEEK), filled with carbon fibres and solid lubricants (polytetrafluoroethylene (PTFE), graphite or MoS2), against steel discs. Oscillating sliding tests were performed in high vacuum environment in the temperature range between -40°C and +160°C. Results indicate that MoS2 filled PEEK show the best tribological performance in vacuum. Particularly, in the lower temperature range and at higher loads the friction behaviour is improved by the MoS2 content.
In the development of hydrogen technology, special attention is paid to the technical problems of
hydrogen storage. One possible way is cryogenic storage in liquid form. Generally cryotechnical
machines need components with interacting surfaces in relative motion such as bearings, seals or
valves, which are subjected to extreme conditions. Materials of such systems have to be resistant to
friction-caused mechanical deformation at the surface, low temperatures and hydrogen environment.
Since materials failure can cause uncontrolled escape of hydrogen, new material requirements are
involved for these tribo-systems, in particular regarding operability and reliability. In the past few
years several projects dealing with the influence of hydrogen on the tribological properties of friction
couples were conducted at the Federal Institute for Materials Research and Testing, (BAM), Berlin.
This paper reports some investigations carried out with polymer composites. Friction and wear were
measured for continuous sliding and analyses of the worn surfaces were performed after the
experiments. Tests were performed at room temperature in hydrogen as well as in liquid hydrogen.
Ensuring a sustainable energy supply is currently one of the most important areas for industry and research institutions. Hydrogen technology is a promising candidate, but its broad extension requires extremely high reliability and safety in all areas for common applications as automobiles and stationary fuel cells. Particularly components containing tribosystems are critical parts.
The sliding performance of PEEK composites was investigated in vacuum environment. Tests were performed with carbon fibre reinforced PEEK composites filled with PTFE, and MoS2 or graphite as further solid lubricant. Polymer samples were tested in a pin-on-disc configuration continuously sliding against CrNi-steel. Depending on sliding speed and temperature, the MoS2 filled composites showed high wear resistance and friction coefficients as low as PVD coatings.