Filtern
Dokumenttyp
Schlagworte
- Zerstörungsfreie Prüfung (2)
- Accuracy of positioning (1)
- Aggregates (1)
- Automated scanning systems (1)
- Automatisierung (1)
- Beton (1)
- Cement-based composites (1)
- DAS (1)
- Data processing (1)
- Distributed acoustic sensing (1)
Organisationseinheit der BAM
Positioning accuracy of an automatic scanning system for GPR measurements on concrete structures
(2012)
Time slices of very dense GPR measurements carried out at concrete with a real point distance of less than 10 mm in x and y direction show weak reflection patterns besides the strong reflections of reinforcements. A repetition of these measurements with the same local geometrical precision at the same specimen shows the same reflection pattem. We suppose that the heterogeneity of concrete given by aggregates (e.g. gravel, broken granite) causes local weak Scattering of the GPR waves and leads to reflection patterns in the GPR data. These reflection patterns can be explained by a Superposition of multiple scatterings of single aggregates. So far these reflection patterns have been not recognized in Standard time slices due to the large spacing (> 5 cm) between single profiles and because of the interpolation between the profiles.
We investigate the characteristics of the volume scattering effects, caused by aggregates, at concrete blocks with two different grading curves. In a more general investigation we study the volume scattering of aggregates by using wooden boxes filled with only typical aggregates and an included defined reflector (metal plate). The thickness of the aggregate layer above the metal plate was varied between 20 cm and 40 cm. With a very dense measuring grid at the surface we are able to calculate the effective volume scattering and to analyze the distribution of the reflection amplitude of the included metal plate for different aggregate set-ups. Results of this study confirm that the weak reflection patterns in concrete can be explained by aggregate scattering and have a direct correlation to the penetration depth of GPR in concrete.
Ultrasonic imaging systems usually require an array of ultrasonic transducers for data acquisition on a wide area on top of an object under investigation. The goal of an imaging algorithm is the use of reflected ultrasound data to form a recognizable image. Conventional algorithms like SAFT are based on an inverse Huygens' principle and need therefore a dense measurement grid. This requires a big effort in data capturing. For simple and inexpensive measurement different strategies of imaging with reduced amount of data and examples with a manual scanning device on concrete elements are presented.
Der Fachbereich 8.2 der Bundesanstalt für Materialforschung und -prüfung (BAM) hat eine innovative Methode zur zerstörungsfreien Ultraschallprüfung erarbeitet und den technischen Aufbau in Form eines neuen Gerätes entwickelt. Mit Hilfe des Produktdesigns soll die Etablierung auf dem Markt sichergestellt werden.
Die Arbeit erläutert detailliert die Bereiche, die für die Gestaltung des Handscangerätes von Bedeutung sind. Sie befasst sich mit der Installation und Handhabung des Systems am Einsatzort und beleuchtet wichtige technische Details. Der nicht verkleidete technische Aufbau der zwei neu entwickelten Geräte dient als Grundlage für die Erarbeitung eines Gehäusekonzepts. Neben dem Gehäusedesign wird eine Überarbeitung des gesamten Aufbaus durchgeführt, um die Benutzerfreundlichkeit in verschiedenen Punkten zu verbessern. Zukünftige Designentscheidungen werden auf Grundlage von praxisnahen Beobachtungen und der notwendigen Anordnung der technischen Komponenten getroffen. Ziel der Auseinandersetzung ist es, ein funktionelles und ästhetisch ansprechendes Design zu entwickeln. Am Ende sollen unter Beachtung aller Vorgaben die Ergebnisse dieser Arbeit zu einem ergonomischen Gerät führen.
Die Problemstellung besteht daraus, den komplexen technischen Vorgaben und Ansprüchen des Projektpartners und Innovationsgebers gerecht zu werden und gleichzeitig ein gutes Designziel zu erreichen. Das Design soll die Funktionalität und Handhabung des Gerätes verbessern und dient als Hilfsmittel, um den komplexen Aufbau zu vereinfachen. Die Benutzerfreundlichkeit soll an allen nötigen Stellen verbessert werden und ein ästhetisch zusammenstehender Gesamteindruck soll entstehen, ohne die Funktionalität negativ zu beeinflussen.
Air voids in concrete like honeycombs are one of the major concerns regarding quality assurance for the construction of infrastructure buildings like bridges or tunnels. This paper shows that voids in reinforced concrete walls or slabs can be detected by two standard ground coupled GPR antennas in transmission mode using a two-side zero-offset profiling configuration like in borehole radar applications. For the detection of voids only the amplitudes of the direct wave in transmission mode are evaluated. Even when the depth of the void can not be detected in this configuration, the major advantage of the zero-offset profiling in transmission mode is a lower interference with the surrounding reinforcement compared to a regular one-side reflection profiling. The capability of the two-side zero-offset profiling is demonstrated on a test specimen with a set of polystyrene balls of two different sizes representing voids like honeycombs in concrete. GPR measurements are realized by an automated scanning system in order to allow for a synchronous movement of the antennas. In transmission mode voids can be detected at greater depths compared to reflection mode, since the travel path of the direct wave is half as long. Another characteristic of the transmission mode is that the direct wave through the air voids is faster and arrives earlier than the direct wave in the surrounding concrete. Hence it can be separated from the strong reflection of the reinforcement. Finally the measurements in transmission mode are less sensitive to the antenna frequency and polarization than in reflection mode.
Impact resistance of reinforced concrete (RC) structures can be significantly improved by strengthening RC members with thin composite layers featuring high damage tolerance. Indeed, to limit the well-known vulnerability of cement-based materials against impact loading, the synergistic effects of short fibres and continuous textile meshes as hybrid reinforcement has been proved to be highly beneficial. This paper addresses the characterisation of novel cement-based hybrid composites through accelerated drop-weight impact tests conducted on rectangular plates at different impact energies. Two distinct matrices are assessed, with particular interest in a newly developed limestone calcined clay cement (LC3)-based formulation. Important parameters quantifying energy dissipation capability, load bearing capacity and damage are cross-checked to compute the ballistic limit and estimate the safety-relevant characteristics of the different composites at hand. Although textiles alone can improve the damage tolerance of fine concrete to some extent, the crack-bridging attitude of short, well-dispersed fibres in hybrid composites imparts a certain ductility to the cement-based matrices, allowing a greater portion of the textile to be activated and significantly reducing the amount of matrix spalling under impact.
Schutzbauwerke von systemkritischen Infrastruktureinrichtungen wie Betonwände und Betonbarrieren müssen Anprallereignissen oder schweren Unfällen in einem vertretbaren Maße widerstehen können. Anprallereignisse können verschiedenster Natur sein. Hierzu zählen Steinschlag, Fahrzeug- oder Flugzeuganprall oder auch Geschosseinschlag. Geschosseinschläge bzw. Bei den Anprall- oder Impaktereignissen wird zwischen hartem und weichem Anprall unterschieden, bei hartem Anprall verformt sich der Anprallkörper nicht oder nur geringfügig, bei weichem Anprall stark.
In diesem Artikel werden Forschungsergebnisse zum harten Anprall auf bewehrte Stahlbetonplatten vorgestellt, welche über die letzten Jahre im Rahmen eines Kooperationsprojekts zwischen dem Institut für Massivbau (IMB) der Technischen Universität Dresden (TUD) und der Bundesanstalt für Materialforschung und -prüfung (BAM) durchgeführt wurden. Auf dem Gelände des Otto-Mohr-Labors (OML) der TUD steht hierfür ein speziell konzipierter Fallturm zur Verfügung. Der Aufbau im Fallturm lässt aktuell druckluftbeschleunigte Impaktversuche mit mittleren Anprallgeschwindigkeiten zu. Die durch Anprall geschädigten Stahlbetonplatten wurden anschließend bei der BAM mit Strahlung tomographisch untersucht. Diese Untersuchungen ermöglichen einen Blick auf die Schädigung und Rissstruktur im Inneren der Stahlbetonplatten.
Ein Schwerpunkt der durchgeführten Untersuchung ist der Vergleich von Testergebnissen mit den häufig angewendeten halbempirischen Berechnungsmethoden zu den erforderlichen Wandstärken und den sich daraus ergebenden zulässigen Anprallgeschwindigkeiten. Bei diesem Vorgehen wird auch die mit analytischen Methoden abschätzbare Durchdringungsgeschwindigkeit bzw. Austrittgeschwindigkeit eines Projektils ermittelt und mit den realen Testergebnissen verglichen. Außerdem wird der Einfluss von sowohl externen als auch internen Strukturparametern auf Risse betrachtet und ein Fazit abgeleitet. Weiterhin werden laufende und zukünftige wissenschaftliche Untersuchungen zum Anprall auf Betonstrukturen am IMB und der BAM genannt.