Filtern
Dokumenttyp
Schlagworte
- (NH4)3InF6 (1)
- 100Cr6 (1)
- 115In and 19F solid state NMR (1)
- ASP20212 (1)
- Alloy (1)
- Aluminium (1)
- BIMAX42 (1)
- Belastungsversuch (1)
- CSS-42L (1)
- Contact pressure (1)
Organisationseinheit der BAM
The paper addresses beech wood as well as vulcanized fiber and discusses the results obtained when using acoustic emission and thermography as non-destructive testing techniques along tensile and load increase fatigue tests to characterize the wooden material’s behavior under increasing fatigue loads to get enhanced information regarding the fatigue behavior of both materials. Reference is mainly made to the materials’ anisotropic and microstructural behavior and what implications this has with respect to the materials’ strength. The influence of moisture is discussed, as well as parameters that may deserve monitoring in the sense of structural health monitoring to be applied in timber structures in general.
DIN 50100 definiert die Bedingungen für den Schwingfestigkeitsversuch, der zur Ermittlung von Kennwerten dient, die das Verhalten metallischer Werkstoffe und Bauteile bei zyklischer Beanspruchung mit einer konstanten Lastamplitude beschreiben (Wöhlerversuch). Die Norm umfasst die Versuchsdurchführung, die Versuchsauswertung sowie die Dokumentation von lastgeregelten Wöhlerversuchen im Zeit- und Langzeitfestigkeitsbereich. Mit DIN 50100 soll erreicht werden, dass die Wöhlerlinien verschiedener Prüfstellen miteinander vergleichbar und die wesentlichen Randbedingungen der Versuchsdurchführung dokumentiert werden. Da die Ergebnisse von Schwingfestigkeitsversuchen streuen, ist die Treffsicherheit für die Schätzung der Kennwerte von der Anzahl der Versuche einer Versuchsreihe abhängig. In Abhängigkeit von einer geforderten Treffsicherheit wird durch die DIN 50100 der erforderliche Stichprobenumfang vorgegeben.
Downsizing (power-to-weight ratio) and higher speeds lead to a rise in Hertzian contact pressures in combination with an increase in surface or oil temperatures. Under such conditions, commonly used bearing steels, such as 100Cr6, reach their limits, creating a demand for alternative slip-rolling resistant steel alloys. The present work therefore compares the slip-rolling performance of various steel types with Maraging- and PM-type steel alloys such as e.g. CSS-42L™, ASP2012, BIMAX42+, in the Hertzian contact pressure range up to P0max of 4 GPa. Through-hardened 100Cr6H (AISI 52100), case-hardened 20MnCr5 (AISI 5120H) and nitrogen alloyed Croni-dur30 (AMS 5898) still compete in terms of slip-rolling and wear resistance and load carrying capacity, whereas Maraging- and PM-type steel alloys offer superior strength and toughness properties.
This study presents for the first time an NMR spectroscopic characterization of the room and high temperature phases of (NH4)3InF6 using 19F and 115In as probe nuclei. The reversible phase transition to the cubic phase at 353 K was followed by MAS NMR in situ. Static NMR experiments of the room temperature phase and MAS NMR experiments of the high temperature phase allowed the determination of the NMR parameters of both nuclei. Finally, the scalar In–F coupling, rarely observed in solid state NMR, is evidenced in both room and high temperature phases of (NH4)3InF6, and measured in the high temperature phase.
Performance and efficiency of piezo-electric stick-slip actuators are dependent on the waveform of the electrical actuation of the piezo-stack. This paper compares between a conventional saw-tooth actuation with two waveforms that feature softer acceleration in order to minimize the duration of the slip-phase. It is shown that the proposed waveforms increase both maximum mechanical output power (by 43%) and overall efficiency (by 25%) of the examined actuator.
The use of supplementary cementing materials (SCMs) added to concrete mixtures can avoid the alkali-silica reaction. Such materials have a wide range of composition and therefore the inhibition mechanisms can be very differently.
The effectiveness of SCMs which provide silica and alumina into the alkaline solution cannot only be explained by reducing the OH--concentration of the pore solution. From dissolution experiments in potassium hydroxide solutions, an interaction was noted between the aggregate and five SCMs via the alkaline solution. Under specific conditions, no silica is released from the aggregate grains.
Mineralogical investigations (XRD, SEM+EDX) of the grain surfaces confirm that quartz is the main source of silica. In the presence of alumina providing SCMs, the quartz dissolution is strongly reduced or even sometimes stopped. On surfaces of grains a very thin layer can be observed which is probably responsible for reduction or stopping of the silica dissolution and therefore for the inhibition of ASR.
Stepping piezoelectric actuators based on the stick-slip effect inherently make use of a friction contact between strator and rotor. This contact defines not only the actuator's performance but also is prone to wear and tear. For broad use, the actuator has to be able to perform around 1 million strokes. To assess the actuator's performance in terms of force, speed, mechanical output, electrical input, and long-term stability under different load- and environmental conditions, as well as different friction partners, a dedicated test-bed for a LSPA30µXS motor by Cedrat Technologies has been set up.
The very strong Lewis acid aluminium chlorofluo-ride (ACF) was loaded with anhydrous HF. The interactionbetween the surface of the catalyst and HF was investigatedusing a variety of characterization methods, which revealed he formation of polyfluorides. Moreover, the reactivity ofthe HF-loaded ACF towards the hydrofluorination of alkyneswas studied.
The preparation of new active pharmaceutical ingredient (API) multicomponent Crystal forms, especially co-crystals and salts, is being considered as a reliable strategy to improve API solubility and bioavailability. In this study, three novel imidazole-based salts of the poorly water-soluble salicylic acid (SA) are reported exhibiting a remarkable improvement in solubility and dissolution rate properties. All structures were solved by powder X-ray diffraction. Multiple complementary techniques were used to solve co-crystal/salt ambiguities: density functional Theory calculations, Raman and 1H/13C solid-state NMR spectroscopies. In all molecular salts, the Crystal packing interactions are based on a common charged assisted +N-H SA)...O-(co-former) hydrogen bond interaction. The presence of an extra methyl group in different positions of the co-former, induced different supramolecular arrangements, yielding salts with different physicochemical properties.
All salts present much higher solubility and dissolution rate than pure SA. The most promising results were obtained for the salts with imidazole and 1-methylimidazole co-formers.