Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (11)
- Posterpräsentation (5)
- Beitrag zu einem Tagungsband (4)
- Vortrag (2)
- Sonstiges (1)
Schlagworte
- Aktive Thermografie (2)
- Druckversuch (2)
- E-Modul (2)
- Image processing (2)
- Nb3Sn (2)
- Resonance testing (2)
- Resonanzmethode (2)
- Stress-strain behavior (2)
- Superconducting (2)
- Superconducting magnet (2)
- Superconducting magnets (2)
- Supraleiter (2)
- Tensile test (2)
- X-ray absorption tomography (2)
- X-ray diffraction (2)
- Young´s modulus (2)
- Zugversuch (2)
- Accelerator magnet coils (1)
- Accelerator magnets (1)
- Active thermography (1)
- Anisotropy (1)
- Blitzlichtanregung (1)
- CERN (1)
- Coefficient of thermal expansion (1)
- Coil winding (1)
- Compression (1)
- Copper (1)
- Differential scanning calorimetry (1)
- EBSD (1)
- Elastic modulus (1)
- Electron backscatter diffraction (1)
- FFT (1)
- Faserverstärkte Verbundwerkstoffe (1)
- Friction (1)
- Gabelsensor (1)
- Härte (1)
- Impact excitation (1)
- Impuls-Anregungs-Methode (1)
- Impuls-Anregungsmethode (1)
- Intermetallic compound (1)
- Kupfer (1)
- Lock-In Anregung (1)
- Lötverbindung (1)
- MMC (1)
- Microstructure (1)
- Mikroindentation (1)
- Mischungsregel (1)
- Molybdenum disulphide (1)
- Phase transformations (1)
- Polymer (1)
- Resonanz (1)
- Rutherford cable (1)
- Signal-to-noise-ratio (1)
- Solder joint (1)
- Solid lubricants (1)
- Stress-strain-behavior (1)
- Structure solution (1)
- Superconductor (1)
- Synchrotron micro-tomography (1)
- Temperature dependence (1)
- Tensile (1)
- Texture (1)
- Thermal expansion (1)
- Ultraschallprüfung mit Matrix-Sensoren (1)
- Volume changes (1)
- X-ray computer tomography (1)
- Young's modulus (1)
- Young`s modulus (1)
- Young’s modulus (1)
- µCT (1)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (2)
The coefficient of thermal expansion (CTE) and the thermomechanical properties of the polymers used in superconducting magnets need to be known in order to predict their stress state under the different magnet assembly and operating conditions.
We have measured Young’s moduli of typically used polymers during in situ heat cycles with the dynamic resonancemethod. The dynamic test results are compared with Young’s moduli determined from quasi-static stress–strain measurements at room temperature, 77 K and 4.2 K. A moderate elastic anisotropy is found for the fiber reinforced polymers. CTEs are compared based on dilation experiments. TheCTEs of the fiber reinforced polymers studied are similar to those of copper or steel. In contrast, the pure resins exhibit relatively larger CTEs.
A test campaign was launched to determine the mechanical properties of the HL-LHC 11 T Nb₃Sn magnet components in order to accurately model the mechanical properties in Finite Element simulations that predict the stress and strain distribution in these magnets. Static and dynamic test methods have been applied for determining elastic materials behavior, and highly accurate Young’s moduli are obtained with the dynamic methods resonance and impulse excitation. These non-destructive methods also enable temperature dependent modulus measurements during in situ heat cycles.
Vergleichende Bewertung verschiedener Verfahren der E-Modulbestimmung für metallische Werkstoffe
(2017)
Für numerische Beanspruchungs- und Lebensdaueranalysen ist die Kenntnis des E-Moduls der eingesetzten Werkstoffe von zentraler Bedeutung. Für seine experimentelle Bestimmung wurden eine Vielzahl von Verfahren entwickelt, die zum Teil werkstoffspezifisch Eingang in die Normung gefunden haben. Prinzipiell können diese Verfahren in zwei Gruppen eingeteilt werden - die statischen und die dynamischen Prüfverfahren. Während die statischen Verfahren auf der direkten Messung des Spannungs-Dehnungs-Zusammenhangs während einer Belastung im elastischen Verformungsbereich beruhen (Zug-, Biege- bzw. Druckversuch) nutzen die dynamischen Verfahren die Analyse der resultierenden Schwingungen nach einer entsprechenden Anregung eines Prüfkörpers (Resonanz- bzw. Impulsanregungsmethode). Für verschiedene Werkstoffe wurden statische und dynamische Verfahren zur E-Modulbestimmung eingesetzt. Die Unterschiede und Vorteile der verschiedenen Verfahren werden vergleichend diskutiert.