Filtern
Erscheinungsjahr
- 2013 (5) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (2)
- Beitrag zu einem Tagungsband (2)
- Vortrag (1)
Schlagworte
- Roughness (2)
- Carbon nanofiber (1)
- Ceramics (1)
- Coating (1)
- Contact mechanics (1)
- DLC (1)
- Fretting (1)
- Friction (1)
- Humidity (1)
- Kontaktmechanik (1)
Eingeladener Vortrag
- nein (1)
Zero wear (Null Verschleiß)
(2013)
Stick-slip and wear behavior of ceramic and polymer materials under reciprocating sliding conditions
(2013)
In many technical applications not only the actual friction coefficient is of importance, but rather the constancy relevant for the functionality. Due to inconstant ffiction values, positioning processes can be substantially influenced as well as vibrations can be induced. The appearance of this tribological effect, named stick-slip, depends on different factors such as sliding speed, relative humidity and ambient temperature occurring primarily after long operating periods. Beside ambient conditions the choice of materials in contact is the main influencing factor of an inconstant coefficient of friction during operating. Certain polymers are well known for their stick-slip tendencies in technical applications. These are on the one hand different modifications of PTFE (polytetrafluoroethylene) reinforced with glass fibers, bronze or graphite and on the other hand thermoplastics such as PE (polyester) or Pf (polyimide). The difference between static and dynamic values of the ffiction force is decisive for stick-slip phenomena. Furthermore, the stick-slip tendency of polymers strongly depends on the elastic material properties. Main softening material areas, which can be found in the contact, represent particularly vulnerable areas. The high friction value in the contact area decreases in most cases by increasing sliding speeds. However, beside polymers ceramic materials can also offer tendencies to stick-slip motion. Klaffke et al. already investigated the influence of ceramic materials on the stick-slip behavior in.
Die Verschleißbeträge können im nm-Bereich quantifiziert werden durch die Berechnung eines Mittelwert-Profils.
Grundlage dieser Berechnung ist die hochauflösende Erfassung der 3D-Topographiedaten, die tribologisch beanspruchte
und nichtbeanspruchte Oberflächenbereiche gleichermaßen beinhalten. Ein bestimmtes Messverfahren
(taktil oder optisch) wird nicht favorisiert. Die vertikale Auflösung des Messverfahrens sollte im nm-Bereich
liegen.---------------------------------------------------------------------------------------------------------------------------------------------------------------------
The wear rates can be quantified in the nm range by calculating a mean profile. Based on this calculation is the
high-resolution recording of the 3D topography data containing tribologically worn and unworn surface areas
alike. A specific measurement method (tactile or visual) is not favored. The vertical resolution of the measurement
process should be in the nm range.
Main focus was on the deposition of carbon nanofibers (CNFs) onto the hard nanocomposite (nc-Ti1 - xAlxN)/(a-Si3N4) (nACo®) coating surface and the investigation of the structure and tribological properties of CNFs. The alcohol chemical vapor deposition (ACCVD) method was employed to prepare CNFs and the deposition temperatures were 600 and 700 °C, respectively. Prior to the CNF deposition, Ni catalyst was deposited onto the nACo® surface using the magnetron sputtering. The influence of the deposition temperature on the carbon nanofibers structure was investigated by Raman spectroscopy and scanning electron microscopy (SEM). The higher order degree of CNF structure is observed with increasing deposition temperature. Tribological tests were carried out under fretting contact conditions against Al2O3 ball. It is shown that the coefficient of friction (COF) decreases from 1.0 to 1.2 for the clean nACo® surface to 0.2–0.4 for the CNF layers deposited on the nACo® surface. The roughness of the nACo® surface was varied and a higher durability of the CNF layers deposited on the rougher nACo® surface is found.