Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (62)
- Vortrag (48)
- Beitrag zu einem Tagungsband (33)
- Beitrag zu einem Sammelband (20)
- Posterpräsentation (2)
- Forschungsbericht (2)
- Buchkapitel (1)
- Sonstiges (1)
Schlagworte
- Wear (21)
- Friction (16)
- Temperature (12)
- Fretting (9)
- Silicon carbide (7)
- Ceramics (6)
- Reibung (6)
- Alumina (4)
- Ceramic (4)
- Humidity (4)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (48)
COMPOSITE MATERIALS OF A 99.7 % ALPHA-ALUMINA MATRIX WITH PLATELETS OF SILICON CARBIDE (SICP) HAVE BEEN PREPARED BY GELCASTING. DENSIFICATION WAS CARRIED OUT BY GAS-PRESSURE SINTERING WITHOUT FURTHER SINTERING AIDS. FIVE DIFFERENT COMPOSITIONS WITH 0, 5, 10, 15, AND 20 VOL.% SICP RESP. HAVE BEEN INVESTIGATED AND TRIBOLOGICAL PROPERTIES WERE CHARACTERIZED. INCREASING AMOUNT OF SICP AS RIGID PARTICLES IN THE FINE GRAINED MATRIX COMPLICATE THE DENSIFICATION PROCESS. WITH THE APPLICATION OF 50 BAR AR PRESSURE DURING THE FINAL SINTERING STEP AT A TEMPERATURE OF 1700 DEGREE C THE DENSITY OF THE SAMPLES COULD BE INCREASED BY 3-5%. INVESTIGATION OF THE TRIBOLOGICAL PROPERTIES AGAINST STEEL AS A COUNTERBODY UNDER UNLUBRICATED OSCILLATING SLIDING CONDITIONS SHOWED A HIGH COEFFICIENT OF FRICTION AND AN INCREASING WEAR RATE UP TO A SICP CONTENT OF 10 VOL. % . AT 15 AND 20 VOL. % SICP RESP. BOTH THE COEFFICIENT OF FRICTION AND THE COEFFICIENT OF WEAR DROP DOWN.
Influence of Slip Viscosity on the Mechanical Properties of High Purity Alumina made by Gelcasting
(1997)
The isoelectric point is a material property for the characterization of acid-base behavior of the powder surface. The IEP of two alumina powders (AKP-30, Grade A) with different particle size characteristics in aqueous suspension has been determined by colloid vibration current (CVI) and particle charge detection (PCD) methods in moderately concentrated suspensions in order to qualify these methods for a future standardization. The solid loading of the suspensions were 1 and 5 vol%. The comparison of the IEP determined by PCD and CVI was in good agreement. However, the solid loading dependence of IEP and a large IEP hysteresis (at 1 vol%) were observed, which do not allow a proper determination of the IEP. The recording of the potential curve and therfore the determination of the IEP with CVI was difficult for the suspension of Grade A powder due to formation of agglomerates at pH values near the pHIEP.
Ceramic particulate composites in the system SiC-TiC-TiB2 sliding against SiC and Al2O3 under water
(1999)
The tribological behaviour of SiC, SiC-TiC and SiC-TiC-TiB2 was determined in oscillating sliding against SiC and -Al2O3 in water at room temperature. The tribo-systems with the composite materials containing TiC and TiB2 differ significantly from the systems with the single phase SiC: The wear is reduced and the friction is increased. The wear reduction up to a factor of 10 is mainly due to the formation of an oxide film containing titanium oxides which is soft, stable in water and well adhering to the bulk material. This oxide film is transferred to the alumina ball but not to the silicon carbide ball.
The gelcasting process was used for manufacturing porous ceramic bodies from nano sized powders. 3 different powders with specific surface areas between 12 and 30 m²/g were used. Solid content of the corresponding slurries was dependent on the milling procedure and the use of a suitable dispersant. For bimodal GradeA powder solid content was as high as 58 vol%. For sintering temperatures between 1250 and 1600°C the porosity varied between 45 and 20%, whereas the pore radii varied between 50 and 91nm. The grain size of crystallites in the sintered microstructures was about 1um. The reflection ratio for visible light increased in comparison to a reference sample made from conventional powder from 0.8 to 0.95 in the wavelenght range around 400nm.
The friction and wear behaviour of a new developed, pressureless sintered TiB2 ceramic was studied in comparison to SiC against SiC and Al2O3 balls under unlubricated conditions at room temperature. Special attention was paid to the influence of relative humidity on friction and wear results. For both ceramics the coefficient of friction against both ball materials decreases with increasing humidity and is higher in tests against alumina than against SiC. The wear rate is affected significantly by humidity and decreases by one order of magnitude for Al2O3/SiC system and by 2 orders of magnitude for SiC/SiC system. For TiB2 wear rates are nearly not affected by humidity against both ball materials and are much smaller than for SiC.
Tribological Characterisation of a Sl3N4-TiN Composite Ceramic in Fretting Tests at Room Temperature
(2004)
With respect to their excellent material properties ceramics are of interest as candidate materials for tribological applications. The friction and wear behaviour of ceramics is often superior to that of metallic materials. Furthermore, an essential improvement of tribological performance will be possible by tailoring of ceramics in the process of powder preparation and sintering technique. Silicon Carbide (SiC) shows interesting friction and wear behaviour at room temperature, even under unlubricated running conditions but is very sensitive against effects of environmental humidity and shows high friction and high wear in the absence of water vapour. The tribological performance of SiC can be improved considerably by adding substantial amounts of TiC and TiB2 to the microstructure thus creating ceramic particulate composite materials.
Various composites in the quasi ternary system SiC-TiC-TiB2 were prepared by a ceramic manufacturing process including sintering temperatures up to 2180 °C. Comparative tribo tests were performed under unlubricated oscillating sliding motion in dry, normal, and moist air and under water lubrication with SiC balls and Al2O3 balls as counter bodies. The friction is affected by the relative humidity (RH) but barely at all by the composition of the composites. The wear resistance of the composites was found to be improved considerably by addition of TiB2 in the range from 20 to 60 %. The highest wear resistance of the system wear was found when Al2O3 was used as counter body material.
Tribologische Prüfungen als begleitende Maßnahme zur Entwicklung von keramischen Tribowerkstoffen
(1999)
Zeta potential as measured with the electrokinetic sonic amplitude (ESA) method has been compared to streaming potential as measured with the particle charge detection (PCD) method. The measurements have been carried out on identical suspensions of a-Al2O3, SiC and Si3N4 with a solids volume fraction of 1% and 10%. Zeta potential and streaming potential are related by a linear function. The correlation coefficients for this relationship are better than 0.99 for the suspensions with 1% solids loading. For the suspensions with 10% solids loading, correlation coefficients are slightly lower due to the influence of increasing viscosity. Regardless of lower correlation at the higher solids loading, the isoelectric pH is constant within the limits of accuracy of the pH measurements.
Tribological characterisation of siliconcarbonitride ceramics derived from preceramic polymers
(2006)
Amorphous SiCN ceramics were prepared in a laboratory scale as disk shaped specimens with 10 mm diameter and 0.3 mm thickness. The friction and wear behaviour was characterised in gross slip fretting tests under unlubricated conditions at room temperature against steel (100Cr6) and ceramic (Al2O3). Tests with a ball-on-disk contact were performed in laboratory air with different content of water vapour. The results show clearly that the relative humidity has a significant effect on friction and wear behaviour. All tests in dry air lead to higher friction and higher wear rate than in normal air. Improved friction and wear behaviour was observed with increasing pyrolysis temperature up to 1100 °C of the SiCN specimens. This is attributed to increasingly better mechanical properties and higher stiffness of the amorphous network due to the evaporation of gaseous organic species and the formation of free graphite like carbon.
Main focus was on the correlation of the coefficient of friction (COF) with the geometrical parameters of the surface during early stage of the running-in period. TiN, TiAlN and AlTiN coatings were prepared by using rotating cathode arc evaporation unit. The roughness of the WC-Co substrate Ra ranged from 0.05 to 0.2 µm and the coating thickness was 2.3 ± 0.2 µm. Part of the samples were subjected to the surface modification by the drag grinding finishing. Geometrical parameters of the surface were evaluated by means of atomic force microscopy (AFM) and fretting tests were conducted with 10 mm diameter alumina ball under 2 N load, 100 µm slip distance and the frequency of 10 Hz. It was found that the distribution of macroparticles strongly influences the geometrical parameters of the surface and the number of macroparticles increases with increasing Al content in the coating. In the case of the positive skewness Ssq of the coating surface, the kurtosis Sku provides a statistically significant effect on the COF, namely the COF depends inversely on the kurtosis Sku. The kurtosis value for TiN was the highest among as-deposited coatings, subsequently, the slowest increase rate in the COF was observed for the TiN coating.