Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (47)
- Beitrag zu einem Tagungsband (37)
- Zeitschriftenartikel (31)
- Beitrag zu einem Sammelband (16)
- Forschungsbericht (14)
- Posterpräsentation (11)
Sprache
- Englisch (89)
- Deutsch (66)
- Mehrsprachig (1)
Schlagworte
- VOC (29)
- Emission test chamber (22)
- Emissionen (9)
- Volatile organic compounds (9)
- SVOC (8)
- Formaldehyde (7)
- Blauer Engel (6)
- Formaldehyd (6)
- OSB (6)
- VVOC (6)
Organisationseinheit der BAM
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (47)
Kurzfassung An neun verschiedenen Hardcopygeräten wurden in unterschiedlichen Emissionsmesskammern (zwei verschiedene 1 m³ - Kammern und eine 20 m³ - Kammer) in Kombination mit geeigneten Probenahme- und Analysenverfahren Untersuchungen zum Emissionsverhalten dieser Geräte hinsichtlich Staub, Ozon und VOC (TVOC) durchgeführt. Luftprobenahme und Analytik erfolgten für VOC mittels Tenax TA und anschließender Thermodesorption (TDS) in Verbindung mit GC / MS. Ozon wurde kontinuierlich bestimmt. Der Ozonanalysator arbeitete auf der Grundlage der flammenlosen Reaktion von Ozon mit Ethylen nach dem Prinzip der Chemilumineszenz. Die Staubbestimmung erfolgte gravimetrisch mittels Glasfaserfilter und Ultramikrowaage. Zusätzlich wurde die Partikelemission während des Druckbetriebes mit einem Partikelzähler bestimmt. Aufgrund der technischen Rahmenbedingungen standen nur kurze Druckzeiten von maximal 36 Minuten zur Verfügung. Um die Gleichgewichtskonzentration in der Prüfkammer zu erreichen, wurde die Luftaustauschrate in den 1 m³ - Kammern auf n = 4,0 bis 4,7 pro Stunde erhöht. Zusätzlich zur Prüfung in den Emissionsmesskammern sind verschiedene Papiere mittels Direkt - TDS sowie unter- schiedliche Toner mittels Headspaceprobenahme in Kombination mit GC / MS hinsichtlich ihres Emissionsverhaltens untersucht worden.
Für die untersuchten Geräte wurden Emissionsraten ermittelt. Sie betrugen für TVOC 0,41 bis 22,4 mg pro Stück und Stunde, für Ozon kleiner 0,02 bis 4,6 mg pro Stück und Stunde sowie für Staub 0,10 bis 7,63 mg pro Stück und Stunde. Verglichen mit Frischfaserpapier wurden bei den Untersuchungen mit Recyclingpapier deutlich höhere SVOC - Konzentrationen nachgewiesen. Im Ergebnis der Untersuchungen wurde ein Prüfverfahren entwickelt, das die Basis für Emissionsmessungen im Rahmen der Umweltzeichen RAL UZ 62, RAL UZ 85 sowie des neuen RAL UZ 114 für Multifunktionsgeräte darstellt. Abstract The emission behaviour with regard to dust, ozone and VOC (TVOC) of nine different hardcopy devices in combination with suitable air sampling and analysis procedures was investigated in different emission test chambers (two different 1 m³ - chambers and one 20 m³ - chamber). Air sampling and analysis for VOC were done by means of Tenax TA and subsequent thermal desorption (TDS) in connection with GC / MS. Ozone was determined continuously. The ozone analyser worked on the basis of the flame rid reaction of ozone with ethylene according to the principle of chemiluminescence. The dust determination was done gravimetrically by means of glass fibre filter and an ultra micro - balance. Additional the particle emission during the printing process was measured with a particle counter. The general technical conditions of the tested hardcopy devices were the reason for short printing times with a maximum of 36 minutes. In order to achieve the equilibrium concentration in the test chambers the air exchange rate in the 1 m³ - test chambers had to be increased to a value of n = 4,0 to 4,7 per hour. Additional to the examination of the hardcopy devices in the emission test chambers different papers were investi- gated by means of direct - TDS and different toners were tested by means of head space sampling in combination with GC / MS. For the examined hardcopy devices emission rates were determined. The emission rates for TVOC ranged from 0,41 to 22,4 mg per piece and hour, for ozone from less than 0,02 to 4,6 mg per piece and hour and for dust from 0,10 to 7,63 mg per piece and hour. The comparison between recycling paper and paper produced from primary fibres showed in general higher SVOC emissions from recycling paper. As the result of the investigations a test method for the determination of emissions from hardcopy devices was developed. This test method is the basis for emission tests in the framework of the German Award of the Environmental Label for office devices RAL -UZ 62, RAL -UZ 85 and the new RAL -UZ 114 for multifunctional devices.
Beschichtete Holzwerkstoffe und daraus hergestellte Produkte, wie z.B. Möbel, sind in nahezu jedem Innenraum mit vergleichsweise großen Oberflächen anzutreffen. Vor dem Hintergrund einer Vielzahl von in Innenräumen verwendeten unterschiedlichen Materialien und Produkten und dem Ziel, die Belastung der Innenraumluft mit flüchtigen organischen
Verbindungen möglichst gering zu halten, ist eine weitgehende Minimierung von Emissionen dieser Verbindungen aus den genannten möglichen Quellen notwendig. Zu diesem Zweck, auch im Hinblick auf die Umsetzung der Konzeption der Bundesregierung zur Verbesserung der Luftqualität in Innenräumen wurde das bestehende deutsche Umweltzeichen RAL-UZ 38 (Blauer Engel) Formaldehydarme Produkte aus Holz und Holzwerkstoffen überarbeitet. Für das Ziel einer Erweiterung von der Einzelverbindung Formaldehyd auf ein breites Spektrum an flüchtigen organischen Verbindungen war ein geeignetes Prüfverfahren als Basis der neuen Umweltzeichen-Vergabegrundlage zu entwickeln. Die Ergebnisse der hierfür durchgeführten Untersuchungen können dem Abschlußbericht entnommen werden.
Background to the studies was the revision of the current selection criteria of the German ecolabel Blauer Engel (Blue angel) for copiers and printers. In the requirements limits were set for ozone, dust and styrene emissions. The former test methods did no longer correspond to todays requirements with regard to emission measurements. In addition, the emission behaviour of hardcopy devices due to the use of different and non-com parable test methods has been recently discussed controversely. For this reason a new test method had to be developed which enables a reliable, reproducible determination of emission rates (ER) for dust, ozone and VOC (volatile organic compounds). The basis for this was the ECMA-Standard 328 compiled by ECMA (European Computer Manufacturer Association) using dynamic chamber measurements. Nine different machines, desktop laser printers as well as office devices like bigger copiers and multifunctional devices were investigated. As a result of the study new criteria for the Blauer Engel for copiers, printers and a new created for multifunctional devices, concerning TVOC, ozone and dust emission were determined. Additionally a model is presented calculating the concentrations in real rooms under usual printing conditions derived from the test chamber results.
In den letzten Jahren ist der Markt für Grobspanplatten (engl.: Oriented Strand Boards, OSB) zum Einsatz beim Hausbau gewachsen. Die Platten werden in Deutschland und Europa hauptsächlich aus Kiefernholz hergestellt und finden Verwendung in Bodenbelägen, Decken und Wänden. Durch ihren Einsatz kann es zu gesundheitlichen Beschwerden, wie Geruchsbelästigungen oder Schleimhautreizungen, kommen. Die Bundesanstalt für Materialforschung und -prüfung (BAM) hat im Auftrag des Umweltbundesamtes (UBA) ein Forschungsvorhaben zu Emissionen aus Holz und Holzwerkstoffen durchgeführt. In Emissionsprüfkammern wurden unter anderem Proben von sechs OSB-Platten aus Baumärkten untersucht und ihre VOC-Emissionen (engl.: Volatile Organic Compounds, VOC) gemessen. Vier dieser Platten von drei verschiedenen Herstellern würden die Anforderungen des Ausschusses zur gesundheitlichen Bewertung von Bauprodukten (AgBB) nicht einhalten. Größtes Problem hierbei sind die ungesättigten Aldehyde. Der Einsatz von Antioxidantien während der Produktion kann helfen, ungewollte Emissionen deutlich zu reduzieren.
The development of a gas mixing system (GMS) that enables dynamic and retraceable production of stable long-term VOC gas mixtures within the ppb range is discussed. In this system pure liquid substances are kept separately at a constant temperature, evaporated according to their vapour pressure and removed by a small inert gas flow. A modular set-up allows flexible handling. All vapours generated are finally united in a mixing chamber. Any concentration level of the gas mixture can be produced by a suitable combination of evaporation temperature, carrier and dilution gas flows. Test results from continuous operation over six weeks are presented. The equipment was tested on seven volatile organic compounds (VOC) of different vapour pressure ranges. It was possible to establish stable operation for the equipment during the entire period and reproducible gas concentrations which were traceable to the mass as an SI unit, thus the system is suitable for long-term tests.---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Im Beitrag wird die Entwicklung eines Gasmischsystems (GMS) beschrieben, das die dynamische und rückführbare Generierung von langzeitstabilen VOC-Gasgemischen im ppb-Bereich erlaubt. Dabei werden Reinsubstanzen separat temperiert, ihrem Dampfdruck entsprechend verdampft und durch einen kleinen Inertgasstrom abgeführt. In einer Mischkammer werden sie schließlich zusammengeführt. Durch die Kombination von Verdampfungstemperatur, Träger- und Verdünnungsgasflüssen ist die Einstellung eines beliebigen Konzentrationsniveaus des Gasgemischs möglich. Aus einem Dauerbetrieb von sechs Wochen werden Untersuchungsergebnisse gezeigt. Dabei wurde die Apparatur mit insgesamt sieben flüchtigen organischen Verbindungen (VOC) unterschiedlicher Dampfdruckbereiche betrieben. Die Anlage lief über den gesamten Zeitraum stabil und lieferte reproduzierbare und auf die Masse als SI-Einheit rückführbare Gaskonzentrationen. Somit ist das Verfahren für Langzeitanwendungen geeignet.
Comparison of different types of emission test chambers and cells regarding VOC- and SVOC-emission
(2005)
Historische Glasmalereien können durch anorganische und organische Luftverunreinigungen geschädigt werden. Chemische Reaktionen der empfindlichen Materialien eines Glasgemäldes (Glas, Malschicht, Blei) mit Luftfeuchtigkeit und den Schadstoffen der Umgebung führen zu Veränderungen der oberflächennahen Schichten des Glases, der Malschichten und schädigen die Bleie. Die Wirkung von Luftschadstoffen, die aus Industrieabgasen und Feuchtigkeit bestehen und als saurer Regen auf die Verglasung von Kirchen und Kathedralen einwirken ist weitgehend bekannt. Emissionen aus Materialien, die zur Verpackung, zum Transport und zur Lagerung von Kunstgegenständen aus Glas eingesetzt werden, können auch Schäden auf den empfindlichen Materialien verursachen. Als flüchtige organische Bestandteile (Volatile Organic Compounds VOC) wurden neben anderen auch organische Säuren analysiert. Das Schädigungspotenzial von Essigsäure, Propansäure, Hexansäure und Oktansäure wurde an Modellproben unter zeitraffenden Bedingungen im Klimaschrank untersucht. Nach einer Versuchsdauer von 12 Wochen waren die Oberflächen der empfindlichsten Modellproben bereits deutlich geschädigt. Hieraus ergibt sich die Schlussfolgerung, dass Materialien mit hohen Emissionsraten an organischen Säuren auch an mittelalterlichen Gläsern unter ungünstigen Bedingungen (geringe Luftwechsel in Depoträumen) Schäden verursachen können.
Schadstoffe in der Vitrinenluft? - Untersuchungen an Vitrinenmaterialien zum Schutz von Kunstwerken
(2008)
Vor dem Hintergrund der notwendigen Revision der Kriterien zur Vergabe des Gütezeichens "Blauer Engel" für Laserdrucker, Kopierer und Multifunktionsgeräte mussten auch die Prüfmethoden angepasst werden, da die alten Verfahren nicht mehr die heutigen Anforderungen der Emissionsmessung erfüllen. In diesem Zusammenhang wurde auch das unterschiedliche Emissionsverhalten von Hardcopy-Geräten auf Grund der verschiedenen und nicht miteinander vergleichbaren Prüfverfahren heftig diskutiert. Aus diesen Gründen wurde ein neues Prüfverfahren entwickelt, mit dem eine verlässliche und reproduzierbare Prüfung der Emissionsraten von Staub, Ozon und flüchtiger organischer Verbindungen auf der Basis des ECMA (European Computer Manufacturer Association) Standards 328 möglich ist. Dazu wurden neun verschiedene Geräte unter verschiedenen Bedingungen untersucht. Als ein Ergebnis dieser Studie wurden neue Kriterien zur Vergabe des "Blauen Engels" für Kopierer, Drucker und Multifunktionsgeräte festgelegt.
Most VVOC were rarely considered in the evaluation of construction products. (Salthammer, 2014) In Germany this will change because the latest version of the German AgBB scheme for health evaluation (2015) now include VVOC, e.g. ethyl acetate and ethanol. In this study selected compounds were tested with the procedure described in ISO 16017 and a method for measuring VVOC with thermal desorption was developed.
Three different adsorbents Tenax TA, Carbograph 5TD and Carbopack X were tested to analyse VVOC according to ISO 16017. For the tested VVOC, Carbograph 5TD showed the best results under the chosen analytical conditions.
Photocatalytical degradation of selected volatile organic compounds in emission test chambers
(2014)
This work focuses on the photocatalytical degradation of selected volatile organic compounds (toluene, butyl acetate, phenol and limonene) under UV-light and blue LED-light (λ = 444 nm) at different relative humidities. Ceramic tiles coated with titanium dioxide were used as photocatalytical active material. The experiments were performed in 20 l emission test chambers with two different kinds of pollutant supply. Toluene was the compound with the highest degradation rate in all performed experiments. A degradation rate of 24 % was obtained under blue LED-light and a relative humidity of (50 ± 5)% and a degradation rate up to 80 % was obtained under UV-light in dry air.
Product emissions chamber testing involves a complex protocol with several sources of measurement uncertainty (ASTM, 2010; ISO, 2006). Despite the potential for significant variability in measurement results within and among laboratories, there is no Standard method available to assess the accuracy of emissions chamber test results. Recently, Germany’s Federal Institute for Materials Research and Testing (BAM) started a program to evaluate the performance of laboratories testing for the AgBB (German Committee for Health-related Evaluation of Building Products) labelling scheme (Wilke et al., 2009). Test method validation was conducted through interlaboratory studies (ILS) with over 30 participants. Simultaneously, the National Institute of Standards and Technology (NIST) and Virginia Tech (VT) started a program to develop a series of reference materials that mimic real building products, can be tested in typical emissions chambers, and have independently known emission rates (Cox et al., 2010). BAM, NIST and VT subsequently joined forces to conduct a series of inter-laboratory studies using the prototype reference material. A pilot ILS was conducted with BAM and NIST followed by an expanded ILS with several participating countries. Results from these interlaboratory studies have the potential to define an internationally-accepted Standard approach to validate results from product emissions tests.
A method for the determination of very volatile organic compounds (VVOC) in air was developed and successfully tested for methanol and ethanol. Carbotrap 300 (R) (a multi-bed tube using Carbopack C (R), Carbopack B (R) and Carbosive SIII (R)) was selected as sorption material for thermal desorption and tested for its suitability for emission test chamber measurements. The adsorption behaviour and the chromatographic results are influenced negatively by spiking aqueous solutions on the adsorption medium for calibration purposes. The latter effect can be reduced by blowing dry air across the adsorbent to remove the adsorbed water. Detection and quantification limits were determined for a GC-FID system and compared to GC-MS. The applicability of the method was tested with a methanol eliminating silane modified polymeric adhesive (SMP-adhesive for parquet) in an emission test chamber.
There is a need for an assessment of the emission properties of volatile organic compounds (VOCs) from consumer products. A method comparison was carried out to evaluate adapted and cost-effective procedures for such items. Smaller and automated emission chambers depicted similar kinetics compared to a 203 L standard chamber. Toy samples made of PVC (Polyvinyl chloride) emitted more VOCs compared to other tested polymeric products. The emissions from 2 selected samples were studied to allow an evaluation of the resulting room concentration and external exposure of a child. Obtained concentrations were not of concern.
Comparison of Formaldehyde Concentrations in Emission Test Chambers Using EN 717-1 and EN 16516
(2018)
For many years EN 717-1 (Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method) is the standard for formaldehyde emission testing of wooden boards. In 2017 EN 16516 (Construction products - Assessment of release of dangerous substances - Determination of emissions into indoor air) was published as a new harmonised standard for the emission testing of construction products. Because test chamber conditions are different, both standards give different concentrations for formaldehyde. For the determination of a conversion factor four test series were set up with different wooden boards.
Volatile Organic Compounds (VOC) are ubiquitous in the indoor air, since they emit from materials used indoors. Investigations of these materials are mostly carried out in test chambers under controlled climatic conditions. Quality control of these test chamber measurements is important but there is a lack of commercially available homogenous reference materials as required for round robin tests or quality assurance of laboratories. The approach of the present study is the impregnation of a supporting material with VOC, which are reproducibly released in measurable chamber air concentrations under standardised test conditions. A polymer made of Thermoplastic Polyurethane (TPU) was chosen as carrier material. It was impregnated with the VOC trimethyl pentanediol isobutyrat (texanol).
Wood-based materials are well-known sources for formaldehyde emission in the indoor environment. Different testing standards lead to different emission values for the materials. Such standards are compared in this study. Besides scenarios with varying loading factors, air exchange rates and climatic conditions were investigated to evaluate the formaldehyde emission potential of different building products.
Under realistic indoor conditions used for the emission chamber tests, exceeding of formaldehyde indoor guide values were obtained. Results showed the need for improvement of wood-based materials with lower formaldehyde emissions and the adaption of testing parameters closer to realistic conditions.
The latest version of the German AgBB evaluation scheme (2015) for construction products includes some VVOC, e.g. formaldehyde, acetaldehyde and acetone. For these VVOC so-called LCI values (lowest concentration of interest) were derived which are used for the calculation of the so-called R-value (risk index, see reference 1 for the calculation). Test chamber measurements of particle boards show that the emissions of VVOC might have significant impact on the R-value and therefore for the health evaluation.
The latest version of the German AgBB evaluation scheme (2015) for construction products includes some VVOC, e.g. formaldehyde, acetaldehyde and acetone. For these VVOC so-called LCI values (lowest concentration of interest) were derived which are used for the calculation of the so-called R-value (risk index, see reference 1 for the calculation). Test chamber measurements of particle boards show that the emissions of VVOC might have significant impact on the R-value and therefore for the health evaluation.
Zur Definition geeigneter Prüfbedingungen und zur Auswahl geeigneter Holzwerkstoffe für die im Vorhaben (UFOPLAN-Vorhaben Standardisierte Formaldehyd- und VOC-Messungen bei Holzwerkstoffen FKZ 3714 95 310 0) geplanten Untersuchungen wurde eine Recherche zu Forschungsergebnissen bezüglich realer Bedingungen (Luftwechsel, Beladung, klimatische Bedingungen im Sommer) durchgeführt. Zu bekannten Fällen von Überschreitungen wurde recherchiert, welche Produkte als Emissionsquellen in Frage kommen. Unter diesem Gesichtspunkt wurden auch Berichte abgeschlossener Forschungsvorhaben ausgewertet.
Der Innenraumluftrichtwert für Formaldehyd in Höhe von 0,1 ppm ist durch das BfR bestätigt worden und bleibt bis auf weiteres bestehen. Die Prüfbedingungen für Formaldehydemissionen aus Holzwerkstoffen dagegen sind nicht mehr aktuell. Das Prüfverfahren für Holzwerkstoffe gilt seit 1991 und basiert auf dem Gebäudestandard von 1984. Eine Definition und Anpassung der Prüfbedingungen an moderne „dichtere“ Bauweise ist notwendig. Es zeigt sich, dass für Verbraucherinnen und Verbraucher eine Unterscheidung von formaldehydbelasteten und -unbelasteten Produkten in der Praxis schwierig ist. Es kann zu fehlerhaftem Einsatz und nicht fachgerechter Verarbeitung der Holzwerkstoffe kommen. Das Ziel des Vorhabens ist die möglichst sichere Einhaltung des Schutzniveaus durch die Anpassung der Prüfbedingungen an den heutigen Gebäudestandard. Aktuelle Versuche und Ergebnisse des Projektes werden vorgestellt. Ergänzende Screening-Versuche (Prüfkammermessungen) weisen Formaldehydemissionen bei verschiedenen Holzwerkstoffen aus dem Handel nach. Für die betrachteten OSB-Platten sind die FA-Emissionen im Allgemeinen geringer als für die untersuchten Spanplatten. Die OSB-Platten zeigen höhere Emissionen für Aceton und Hexanal als die Spanplatten.
An ausgewählten Werkstoffen wurden Versuche zu den Auswirkungen einer individuellen Bearbeitung und Messungen unter veränderten Prüfbedingungen durchgeführt. Zum einem wurde schrittweise der Luftwechsel von 1 bis 0,2 1/h reduziert. Zum anderen wurden die Werkstoffe unter sommerlichen Bedingungen vermessen.
Die Reduzierung des Luftwechsels ruft einen Anstieg der Formaldehyd-Konzentration hervor, dieser Effekt ist jedoch für einige VOCs stärker ausgeprägt. Bei Luftwechseln von 0,2-0,3 1/h, welche in der Praxis in Gebäuden erreicht werden können, ist eine Überschreitung des Formaldehyd-Grenzwertes von 0,1 ppm vor allem für Spanplatten möglich. Die VOC-Emission steigt unter sommerlichen Bedingungen an, es zeigt sich aber ein schnelles Abklingen nach kurzer Zeit. Die erhöhte Formaldehydemission bleibt über einen längeren Zeitraum erhalten. Die Bearbeitung von unbeschichteten Holzwerkstoffen (in mehrere Teile zersägt) führt zu einem kurzzeitigen Anstieg der FA- und VOC-Emission, nach einer bestimmten Abklingzeit (wenige Tage) wird erneut der Ausgangswert erreicht.
Es wurden weiterhin Messungen zu Kombinationen aus OSB- und Spanplatten und einem Holzmöbel durchgeführt. Trotz Erhöhung der Beladung und Beibehalten des Luftwechsels konnte nur ein geringer Anstieg der Formaldehyd- und VOC-Konzentration beobachtet werden. Es erfolgte keine Addition der Einzelkonzentration.
Most VVOC were rarely considered in the evaluation of construction products. (Salthammer, 2014) In Germany this will change because the latest version of the German AgBB scheme for health evaluation (2015) now include VVOC, e.g. ethyl acetate and ethanol. In this study selected compounds were tested with the procedure described in ISO 16017 and a method for measuring VVOC with thermal desorption was developed.
Three different adsorbents Tenax TA, Carbograph 5TD and Carbopack X were tested to analyse VVOC according to ISO 16017. For the tested VVOC, Carbograph 5TD showed the best results under the chosen analytical conditions.
Der Innenraumluftrichtwert für Formaldehyd in Höhe von 0,1 ppm ist durch das BfR bestätigt worden und bleibt bis auf weiteres bestehen. Die Prüfbedingungen für Formaldehydemissionen aus Holzwerkstoffen dagegen sind nicht mehr aktuell. Das Prüfverfahren für Holzwerkstoffe gilt seit 1991 und basiert auf dem Gebäudestandard von 1984. Eine Definition und Anpassung der Prüfbedingungen an moderne „dichtere“ Bauweise ist notwendig. Es zeigt sich, dass für Verbraucherinnen und Verbraucher eine Unterscheidung von formaldehydbelasteten und -unbelasteten Produkten in der Praxis schwierig ist. Es kann zu fehlerhaftem Einsatz und nicht fachgerechter Verarbeitung der Holzwerkstoffe kommen. Das Ziel des Vorhabens ist die möglichst sichere Einhaltung des Schutzniveaus durch die Anpassung der Prüfbedingungen an den heutigen Gebäudestandard. Es werden das Projekt (UFOPLAN-Vorhaben FKZ 3714 95 310 0) und erste Messergebnisse vorgestellt. Erste Messungen von Holzwerkstoffen im laufenden Vorhaben unter „worst case“-Bedingungen (erhöhte Beladung, geringer Luftwechsel) zeigen hohe Formaldehyd-Emissionen.
Berichtet wird über ein abgeschlossenes Folgeprojekt zu vorangegangenen Forschungsprojekte zum gleichen Thema. In diesem Projekt wurde das Messverfahren und der Prüfwert für die Partikelemission aus Bürogeräten (siehe Vergabegrundlage DE-UZ 205, Anhang S-M) validiert und weiterentwickelt. Dies geschah erstens durch Auswertung der Qualität der im Zuge der Antragsbearbeitung für das Umweltzeichen beim RAL vorgelegten Prüfberichte der zugelassenen Prüfinstitute und - basierend darauf - durch Erarbeitung von technisch-methodischen Veränderungsvorschlägen für die Prüfung der chemischen Emissionen, inklusive der Partikelemissionen. Zweitens wurde zur Beurteilung der Veränderung der Emissionen aktueller gegenüber älteren Geräte-generationen ein nicht repräsentativer Pool von table-top-Laserdruckern aufgebaut und die chemischen Emissionen wurden gemäß DE-UZ-205, Anhang S-M gemessen. Ergänzend wurde eine quantitative chemische Analyse der anorganischen Feststoffe - insbesondere der Metalle - in den emittierten Aerosolen vorgenommen die Feststoffgehalte um 2 Massen-% ergaben. Diese Ergebnisse wurden gemeinsam mit neueren wissenschaftlichen Untersuchungen zur gesundheitlichen Bewertung der Emissionen aus Laserdruckern ausgewertet, es besteht kein Handlungsbedarf hinsichtlich einer Veränderung von Prüfkriterien und Prüfwerten. Drittens wurde untersucht und bestätigt, dass mit dem Ziel eines zukünftigen Umweltzeichens das Emissionsverhalten Kunststoff verarbeitender 3D-FDM-Drucker und/oder die darin verarbeiteten Verbrauchsmaterialien (Filamente) mit dem für Laserdrucker entwickelten Mess- und Prüfschema charakterisiert und quantifiziert werden können. Untersuchungen an Stereo-lithografie (SLA)-Druckern und Vorrichtungen zur Nach-Aushärtung (Curing Units) ergaben keine nachweisbaren Partikelemissionen.
The chemical emissions from products are tested by means of emission test chambers under defined conditions (climate, loading, air change rate). The standard method for the determination of volatile organic compounds (VOC) is the sampling onto Tenax-tubes followed by thermal desorption (TDS) and gas chromatography-mass spectrometry (GC-MS) analysis. The EU-LCI list includes some very volatile organic compounds (VVOC) and some VOC for which there are limitations when using the standard method. For VVOC additional sampling is required using stronger absorbers like Carbotrap or multi-bed adsorption tubes. The analysis of VVOC also requires a different GC oven program and a different column for the separation. For the determination of formaldehyde and other low boiling aldehydes (e.g. acetaldehyde, acetone, propanal, propenal) DNPH-cartridges are used which are extracted with acetonitrile followed by liquid chromatography (HPLC-UV) analysis. The derivatisation of propenal and other unsaturated aldehydes (e.g. 2-butenal) with DNPH might lead to lower findings due to incomplete derivatization and forming of by-products. For a better quantification of acetic acid the use of ion chromatography (IC) is recommended because the analysis of acetic acid with the standard method (TDS) leads to lower findings due to break through during sampling. The use of ion chromatography for the analysis of organic acids requires a third sampling technique. The acids are adsorbed onto silica-gel and extracted with water.
UBA und BAM schlagen die Durchführung der Prüfkammermessungen bei 23 °C und 50% relativer Luftfeuchte, einer Beladung von 1,8 m²/m³ und einem Luftwechsel von 0,5 pro Stunde vor. Diese Parameter orientieren sich an der EN 16516, die als zukünftige „Referenznorm“ zu betrachten ist. Die Schmalflächenversiegelung ist auch zukünftig wie in der EN 717-1 beschrieben vorzunehmen. Nach 28 Tagen wird der Mittelwert einer Doppelbestimmung als Endkonzentration („entsprechend der Ausgleichskonzentration“) berechnet. Alternativ dazu kann die Prüfung vorzeitig abgebrochen werden, wenn an 5 Messtagen der Prüfung eine Formaldehydkonzentration von 0,1 ppm nicht überschritten wird.
Prüfungen nach der EN 717-1 sollen weiterhin gleichberechtigt möglich sein. Ergebnisse von Messungen, die nach der EN 717-1 ermittelt wurden, sind mit dem Faktor 2,0 zu multiplizieren.
Abgeleitete Verfahren wie z.B. das Gasanalyseverfahren sollen weiterhin möglich sein. Das Perforatorverfahren entfällt hier, da eine allgemeine für alle Holzwerkstoffe gültige Korrelationen nicht existiert.
Die entsprechenden Änderungen sind in der vom BMUB veröffentlichten „Bekanntmachung analytischer Verfahren für Probenahmen und Untersuchungen für die im Anhang der Chemikalien-Verbotsverordnung genannten Stoffe und Stoffgruppen“ entsprechend zu ändern.
Growing awareness of the impact of monoterpenes on climate, atmospheric chemistry, and indoor air quality has necessitated the development of measurement standards to globally monitor and control their emissions. For National Metrology Institutes to develop such standards, it is essential that they demonstrate measurement equivalence for assigned values at the highest levels of accuracy. This report describes the results of a pilot comparison for 4 key monoterpene species: α-pinene, 3-carene, R-limonene and 1,8-cineole, at a nominal amount-of-substance fraction of 2.5 nmol mol-1. The objective of this comparison is to evaluate participant capabilities to measure trace-level monoterpenes using their own calibration techniques.
The ISO 16000 standard series provide guidelines for emission measurements of volatile organic compounds (VOCs) from building materials. However, polymer-based consumer products such as toys may also release harmful substances into indoor air. In such cases, the existing standard procedures are unsuitable for official control laboratories due to high costs for large emission testing chambers. This paper aims at developing and comparing alternative and more competitive methods for the emission testing of consumer products. The influence of the emission chamber size was investigated as smaller chambers are more suited to the common size of consumer products and may help to reduce the costs of testing. Comparison of the performance of a 203 l emission test chamber with two smaller chambers with the capacity of 24 l and 44 ml, respectively, was carried out by using a polyurethane reference material spiked with 14 VOCs during the course of 28 days. The area-specific emission rates obtained in the small chambers were always similar to those of the 203 l reference chamber after a few hours. This implies that smaller chambers can provide at least useful numbers on the extent of polymer-based consumer product emissions into indoor air, thereby supporting meaningful exposure assessments.
Im Januar 2018 wurde die DIN EN 16516 „Bauprodukte: Bewertung der Freisetzung gefährlicher Stoffe – Bestimmung von Emissionen in die Innenraumluft“ als harmonisierte europäische Prüfnorm veröffentlicht. Für die Etablierung der DIN EN 16516 als neue Referenznorm wurden verschiedene Emissionsprüfungen mit dem Ziel durchgeführt, ein neues Prüfverfahren für Formaldehydemissionen aus Holzwerkstoffen zu erarbeiten. Das übergeordnete Ziel ist die Minimierung des Risikos von Überschreitungen des Innenraumrichtwertes für Formaldehyd. Die Untersuchungen ergaben teilweise hohe Formaldehydemissionen, insbesondere bei höheren Beladungsfaktoren und Temperaturen, sowie bei niedrigen Luftwechselraten. Eine getestete Spanplatte hätte aufgrund ihrer hohen Formaldehydemission nicht auf den deutschen Markt gebracht werden dürfen. Durch vergleichende Untersuchungen konnte ein Umrechnungsfaktor in Höhe von 2,0 für die Umrechnung von Prüfwerten nach DIN EN 717-1 zu DIN EN 16516 abgeleitet werden.
Die von der BAM eingekauften Holzwerkstoffplatten (Verlegespanplatten, OSB, Multiplexplatten) verschiedener Hersteller zeigten teilweise hohe Formaldehyd-emissionen unter den Prüfbedingungen nach EN 16516, eine Spanplatte hielt den Grenzwert von 0,1 ppm selbst bei Prüfung nach DIN EN 717-1 nicht ein, dürfte also in Deutschland gar nicht in den Verkauf gelangen.
Holzwerkstoffe, die unter den Prüfbedingungen der DIN EN 717-1 die Formaldehydklasse E1 einhalten, können insbesondere bei großflächigem Einsatz im Innenraum zu Überschreitungen des Richtwertes für die Innenraumluft führen. Zusätzlich zur Anpassung des Luftwechsels ist auch der Parameter Beladung bei einer Überarbeitung der Norm anzupassen. In der DIN EN 16516 werden produktspezifische (am Einsatz der Produkte orientierte) Beladungsfaktoren vorgegeben. Für den Einsatz von Holzwerkstoffplatten ergäben sich Beladungen von 0,4 (Boden oder Decke), 1,0 (Wände), 1,4 (Wände plus Boden oder Decke) und 1,8 m²/m³ (Wände, Boden und Decke). Um die realen Bedingungen in modernen Gebäuden abzubilden, ist deshalb eine Beladung von 1,8 m²/m³ für die Prüfkammermessung erforderlich. Hierbei ist darauf hinzuweisen, dass für die Beladung im Referenzraum Möbel nicht berücksichtigt wurden.
Damit soll sichergestellt werden, dass die Einhaltung des Schutzniveaus bei realen Innenraumbedingungen auch unter den Randbedingungen eines niedrigen Luftwechsels sowie bei sommerlichen Bedingungen und heutigem Lüftungsverhalten der Menschen soweit wie möglich gewährleistet ist.
Previous studies have shown that desktop 3D printers (Fused Filament Fabrication) emit high numbers of particulate matter, mainly as ultrafine particles (UFP, particle diameter less than 100 nm). However, the chemical composition of emitted particles has been less extensively investigated. In this study, we therefore focused on the chemical composition of particles emitted from 3D printing. The measurements were conducted in a 1 m³ emission test chamber. Emitted particles were sampled by a 13-stage low-pressure cascade impactor onto aluminum foils and then analyzed by TD-GC/MS to identify their organic compounds. Nine commercial filaments made from basic polymers such as Acrylonitrile Butadiene Styrene (ABS), Acrylonitrile Styrene Acrylate (ASA), Polycarbonate (PC), Poly(methyl methacrylate) (PMMA), Nylon, High Performance Polystyrene (HIPS) and a copper-filled Polylactide (PLA) were investigated. The results show that the organic components of the particles are primarily plastic additives such as plasticizer, antioxidant agents, lubricants, UV-absorbers and UV-stabilizers from the filaments.
11 laser printers from 5 manufacturers were purchased in 2017 and tested for their UFP emissions. Size resolved sampling of the emitted particles was done with a 13 stage (30 nm to 10 µm) low pressure cascade impactor. The sampled particles were analysed for their chemical composition by thermal extraction (vaporization at 290°C) followed by GC-MS analysis. High boiling cyclic siloxanes (D10 to D16) were detected as constituents of UFP from laser printers. In comparison to measurements in 2008, aliphatic long-chain alkanes (C22 to C34) were detected additionally as chemical constituents of UFP from most of the tested printers and their amounts were higher than for cyclic siloxanes. Printers of one manufacturer showed very low UPF emissions compared to the other manufacturers.
11 laser printers from 5 manufacturers were purchased in 2017 and tested for their UFP emissions. Size resolved sampling of the emitted particles was done with a 13 stage (30 nm to 10 µm) low pressure cascade impactor. The sampled particles were analysed for their chemical composition by thermal extraction (vaporization at 290°C) followed by GC-MS analysis. High boiling cyclic siloxanes (D10 to D16) were detected as constituents of UFP from laser printers. In comparison to measurements in 2008, aliphatic long-chain alkanes (C22 to C34) were detected additionally as chemical constituents of UFP from most of the tested printers and their amounts were higher than for cyclic siloxanes. Printers of one manufacturer showed very low UPF emissions compared to the other manufacturers.
The presentation gives general information about the European Standard EN 16516 “Construction products – Assessment of release of dangerous substances – Determination of emissions into indoor air”. This test standard was developed based on the mandate M/366 of the European commission and is a horizontal reference method for the determination of volatile organic compounds (VOC) from different classes of construction (building) products. Specific test conditions are to be selected by the product TCs (technical committees) in a way that a product is tested under its intended condition of use.
The test is based on the use of emission test chambers which are operated at constant air change rate and climate (23°C, 50 % r.h.) over 28 days. The standard defines the conditions and requirements for the measurement including loading factor, air change rate, sampling, analysis and calculation of emission rates of the substances. A 30 m³ reference room is described which is used to calculate air concentrations from the determined emission rates.
The standard EN 16516 enables the evaluation of construction products regarding their emissions into indoor air under defined and comparable conditions. The evaluation includes the determination of identified target compounds, non-identified target compounds, volatile carcinogenic compounds and the sum values TVOC, TSVOC and R.
Emission testing of volatile organic compounds (VOC) from materials and products is commonly based on emission test chamber measurements. To ensure the comparability of results from different testing laboratories their measurement performance must be verified. For this purpose, Bundesanstalt für Materialforschung und -prüfung (BAM) organizes an international proficiency test every two years using well-characterised test materials (one sealant, one furniture board and four times a lacquer) with defined VOC emissions. The materials fulfilled the requirements of homogeneity, reproducibility, and stability. Altogether, 41 VOCs were included of which 37 gave test chamber air concentrations between 10 and 98 µg/m³. This is the typical concentration range to be expected and to be quantified when performing chamber tests. Four compounds had higher concentrations between 250 and 1105 µg/m³. The relative standard deviations (RSD) of BAM proficiency tests since 2008 are compared and the improvement of the comparability of the emission chamber testing is shown by the decrease of the mean RSD down to 23% in 2021. In contrast, the first large European interlaboratory comparison in 1999 showed a mean RSD of 51%.
Round robin tests of odour and VOC emissions from building products – What have we learned so far?
(2023)
Emission testing of volatile organic compounds (VOC) and odour from materials and products is commonly based on emission test chamber measurements. These measurements are often the basis of mandatory or voluntary labelling procedures. To ensure the comparability of results from different testing laboratories their performance must be verified. For this purpose, round robin tests (RRTs) are conducted. Bundesanstalt für Materialforschung und - prüfung (BAM) offers such a RRT every two years using well characterised test materials with defined VOC emissions. In addition to the VOC quantification, the evaluation of odour is also implemented in the round robin tests. At the beginning, only perceived intensity (PI) was tested but over the years also the acceptance evaluation was considered. In principle, the results of PI and acceptance evaluation are comparable. The advantage of PI is the lower number of panel members necessary for one evaluation.
Since Central Europeans spend most of their time indoors, the quality of the indoor air is important. Sources of volatile organic compounds (VOC) indoors are e. g. building materials, wall and floor coverings and interior equipment, whose emissions might influence the health and wellbeing of people. Photocatalysis is one opportunity to improve the indoor air quality by degrading VOCs ideally to carbon dioxide and water. Titanium dioxide (Ti02) in its anatase modification (band gap of 3.2 eV) is a common used UV-active photocatalytic coating. Because of the lack of UV light indoors Ti02 needs to be modified to be active under visible light too. This work focuses on the photocatalytic degradation of toluene, butyl acetate and limonene under UV LED light and blue LED light in emission test chambers under controlled climatic conditions. These compounds were selected due to their frequent occurrence in the indoor environment and their supply was done with a gas mixing System. Ceramic tiles coated with modified and pure Ti02 were used as photocatalytic active material. Previous results and experimental details were already published by Mull and Wilke (2014).
Summary: A screening test for potential emissions of volatile organic compounds (VOC) was run on different thermoplastic filaments used for 3D printing. The method of direct thermal desorption was used to simulate the high temperatures during the 3D printing process and to identify the main compounds emitted from the filaments. A large number of unexpected compounds were detected that might affect the user’s health and have an impact on indoor air chemistry.
Introduction: The use of desktop 3D printers is increasing. Compared to other devices with known emissions, e.g. laser printers, there is still a lack of information on possible emissions of VOC and ultrafine particles during operation and the effect on indoor air quality. Most of the commercially available desktop 3D printers operate with a molten polymer deposition. For this process a solid thermoplastic filament is heated in an extrusion nozzle. Most filaments for desktop 3D printers use either acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) as filament. Alternatives are polyvinyl alcohol (PVA) or polycarbonate (PC).
Method: Eight different thermoplastic filaments for 3D printers were analysed by direct thermal desorption followed by GC-MS identification of the emitted substances. Direct thermal desorption was done by desorbing 5 mg of the feedstock for 1 minute at a temperature of 210°C. This is an average temperature for 3D printing with thermoplastic filaments.
Results and conclusions: The comparison of the 4 different filament groups showed the highest overall emissions from ABS, followed by PLA, PC and PVA. Filament ABS 2 emitted mainly SVOCs and triphenyl phosphate, the latter has the highest emission for a single compound from all evaluated filaments.
Thermoplastic filaments are a new source of VOC emissions due to the high temperatures associated with 3D printing, which can reach up to 270°C. Some of the detected compounds like lactic acid, lactide and bisphenol A have never been described before in the indoor environment. Additionally some of the main substances could not be identified and some others might have the potential to affect the indoor air chemistry.
The appearance of some newly detected compounds raises concerns about potential health effects for the users of 3D printers at home.
Drucker, Kopierer und Multifunktionsgeräte können zu einer Schadstoffbelastung der Innenraumluft beitragen. Insbesondere Staub, Ozon und flüchtige organische Verbindungen (VOC, Volatile Organic Compounds) werden beobachtet. Geräte mit besonders geringen Emissionen, die weitere umweltrelevante Anforderungen einhalten, können mit dem Umweltzeichen Blauer Engel ausgezeichnet werden. Die Vergabegrundlage für den Blauen Engel begrenzt neben den genannten Stoffen auch noch speziell die Emission von Benzol und Styrol, und sie enthält die Prüfvorschrift zur Bestimmung der Emissionen. In der vorliegenden Publikation werden Ergebnisse von Emissionsmessungen an 57 verschiedenen Geräten unterschiedlicher Hersteller aus den Jahren 2003 bis 2004 vorgestellt. Ein besonderer Schwerpunkt liegt hierbei neben der Darstellung der summarischen VOC-Emissionen (TVOC, Total Volatile Organic Compounds) auf den wichtigsten Einzel-VOC, wie z.B. Benzol, Styrol, Phenol, Xylole. Diese für Drucker und Kopierer typischen Verbindungen ließen sich mit Emissionsraten von bis zu einigen Milligramm pro Stunde feststellen. Zusätzlich traten auch Siloxane mit vergleichbaren Raten auf, die bisher als Emissionen aus Druckern und Kopierern nur wenig Beachtung fanden. In einigen Fällen waren hohe Emissionen an VOC, die sich einer ausreichenden Identifizierung entzogen, feststellbar. Aus den ermittelten Emissionsraten wurden für einen Modellraum mögliche resultierende Raumluftkonzentrationen berechnet. Diese Berechnungen setzen voraus, dass Emissionen nicht den gesamten Tag über erfolgen, sondern unter üblichen Nutzungsbedingungen über maximal 10% des Arbeitstages. Für Emissionen der druckbereiten Geräte hingegen wurde eine Belastung über den ganzen Tag zugrunde gelegt. Ergänzend werden Emissionsraten für Ozon und Staub vorgestellt.
English:
Hardcopy devices like printers, copiers and multifunctional devices contribute to indoor air pollution. Low emitting devices, that fulfil additional environment related requirements, can be labelled with the eco label "Blue Angel". It limits emissions of benzene, styrene, TVOC, dust and ozone. Results are given for 57 different devices investigated during the years 2003 and 2004. Additionally to TVOC, benzene and styrene further information is given for other emitted VOC like phenol and xylenes. These typical VOC showed emission rates up to some mg/ h but some more uncommon VOC like siloxanes were found in a comparable range, too. In some cases high emission rates were found for compounds which could not be identified. The measured emission rates were taken to calculate indoor air concentrations for a typical situation. For this purpose it was considered that printing is normally limited to less than 10 % of a working day whereas emissions from the stand by phase occur all day long. In addition emission rates for ozone and dust are presented.
Photocatalysis is a promising technique to reduce volatile organic compounds indoors. Titanium dioxide (TiO2) is a frequently-used UV active photocatalyst. Because of the lack of UV light indoors, TiO2 has to be modified to get its working range shifted into the visible light spectrum. In this study, the photocatalytic degradation of toluene, butyl acetate and limonene was investigated under UV LED light and blue LED light in emission test chambers with catalysts either made of pure TiO2 or TiO2 modified with graphene oxide (GO). TiO2 coated with different GO amounts (0.75%–14%) were investigated to find an optimum ratio for the photocatalytic degradation of VOC in real indoor air concentrations. Most experiments were performed at a relative humidity of 0% in 20 L emission test chambers. Experiments at 40% relative humidity were done in a 1 m³ emission test chamber to determine potential byproducts. Degradation under UV LED light could be achieved for all three compounds with almost all tested catalyst samples up to more than 95%. Limonene had the highest degradation of the three selected volatile organic compounds under blue LED light with all investigated catalyst samples.
Vor dem Hintergrund der anhaltenden öffentlichen Diskussion um mögliche gesundheitliche Risiken von Ultrafein- und Feinstaubemissionen aus Bürogeräten mit Laserdruckfunktion (LPD, Laser Printing Device) wurde vom Umweltbundesamt ein Forschungsvorhaben zur Entwicklung einer Prüfprozedur für die Quantifizierung der emittierten Partikel durch Zählung unter Standardbedingungen in Emissionsmesskammern, sowie zur physikalischen und chemischen Charakterisierung dieser Aerosole initiiert. Als Ergebnis konnte die Partikelzählung in den Entwurf des Prüfverfahrens für die Bestimmung von Emissionen (RAL-UZ-122, Anhang S-M) des Umweltzeichens "Blauer Engel" für Bürogeräte sowie in den Prüfstandards ECMA-328 und den Entwurf der ISO/IEC 28360 integriert werden. Die Methode wurde in einem internationalen Ringversuch erfolgreich getestet. Auf dieser Basis können Vergabekriterien und -werte für die Emission von Fein- und Ultrafeinpartikeln im Rahmen der Vergabe des Umweltzeichens Blauer Engel vereinbart und Produktprüfungen vorgenommen werden.
Biocides are used to protect materials that might be damaged by fungal, microbial or insect activity. The aim of this study is to develop a method for the measurement of these organic compounds, which generally have low or moderate vapor pressures. The biocides considered in this study are permethrin, dichlofluanid, tolylfluanid, iodpropinylbutylcarbamat, octylisothiazolinone, tebuconazole and propiconazole. The emission from two commercial products (plastic foil, wool carpet) containing biocides and of seven types of biocidal formulations applied to wood or clay tiles were investigated in 20-l glass emission test chambers. Each chamber test was performed over a period of 100200 days, and one investigation was conducted over several years. Compared to volatile organic compounds, low-volatility compounds show totally different emission curves in chamber tests; maximal emission values may be reached in days or weeks. A period of 3 months is sometimes necessary for the determination of area-specific emission rates (SERa's). The SERa's (?g m-2 h-1) from biocide-containing products were determined for permethrin (0.006), propiconazole (0.3), dichlofluanid (2.0), tolylfluanid (1.0), octylisothiazolinone (2.5) and iodpropinylbutylcarbamat (2). In most cases, the SERa stayed at its maximum value or declined slowly over the test period. Additionally, a chamber test begun in 1994 with a piece of wood treated with a typical mixture of biocides dissolved in a technical solvent was continued. SERa's (?g m-2 h-1) for dichlofluanid (0.20), tebuconazole (0.49) and permethrin (0.08) remained detectable after the period of nearly 9 years during which the sample remained continuously in the chamber. This test proved the very slow decrease of emission of low-volatility compounds like permethrin and tebuconazole.
The European biocides directive (98/8/EG) demand the control of emissions into the envi-ronment like soil, water and air. In this study a method for measuring the input of biocides into the indoor air from materials should be developed. The emission of two products containing biocides (plastic foil, wool carpet) and six different types of biocide containing formulations applied on wood or ceramic tiles were investigated in 20 or 23 l glass emission chambers. Each chamber test was performed over a period of 100 up to 200 days. SVOC show totally different emission curves in chamber tests compared to volatile organic com-pounds (VOC). They reach their maximum value after some days or weeks. Thus a period of 3 months is sometimes necessary for exact measurements. Area specific emission rates (SERa in µg/m²h) for permethrin (0.006), propiconazole (0.2), dichlofluanid (1.5), tolylfluanid (1.2), octylisothiazolinone (2.5) and for iodpropinylbutyl-carbamat (1.7) were determined.
VOC/SVOC-Emissions from materials for flooring installation (primer, screed, adhesive, floor covering) were measured by means of emission test chambers and cells over a time period of at least 28 days at 23 C, 50 % relative humidity and an area specific air flow rate of q = 1.25 m³/m²h. Single components were tested in comparison to three complete structures (same concrete, primer, screed, adhesive) with different types of floor covering (PVC, carpet, linoleum). Sorption into concrete/screed and different sealing by the flooring materials affected the emissions from the complete structures. The complete structures with linoleum and PVC showed the same emissions and emission rates as the flooring materials alone. Emissions from the carpet-covered structure resulted mainly from the lower layers. For two adhesives the formation of secondary emissions (aldehydes and organic acids) was observed starting after the standard testing time of 28 days.
Möglichkeiten und Grenzen bei der Bestimmung von SVOC-Emissionen aus Materialien und Produkten
(2002)
Im vorliegenden Bericht wurden 11 Fußbodenbelagskleber, eine Grundierung, eine Spachtelmasse, 14 Teppiche, 5 PVC-Bodenbeläge, drei Linoleum-Beläge, ein Kautschukbelag und ein Polyolefinbelag über einen Zeitraum von mindestens 28 Tagen mittels Prüfkammer- bzw. Prüfzellenmessung auf ihr Emissionsverhalten untersucht. Die Emissionsmessungen an den Einzelmaterialien Kleber und Bodenbelag sollten die möglichen Emissionen (Substanzen und Konzentrationen) und deren zeitlichen Verlauf ermitteln. Außerdem wurden die Emissionen aus 7 Materialkombinationen ermittelt. Dazu gerhörten drei Komplettaufbauten aus Estrich, Grundierung, Spachtelmasse und Kleber mit den Belägen Teppich, PVC und Linoleum sowie 4 Verbundsysteme. Dies waren: Verbundsystem Estrich/Grundierung/Spachtelmasse/Kleber, Verbundsystem Glasplatte/Kleber/Teppich, Verbundsystem Glasplatte/Kleber/PVC-Belag und das Verbundsystem Estrich/Kleber. Die Emissionen aus den Komplettbauten wueden durch Sorptionseffekte und durch die unterschiedliche Durchlässigkeit der Bodenbeläge beeinflusst. Dabei waren die Emissionen aus den Komplettaufbauten und Verbundsystemen jeweils geringer als die Summe der Emissionen der entsprechenden Einzelmaterialien. Ergänzende Untersuchungen wurden durchgeführt zur Vergleichbarkeit der Emissionsmessungen in unterschiedlichen Prüfkammern (Volumen 1 m3 und 0,02 m3) bzw. Messzellen(Volumen 1 l und 0,035 l [FLEC]). und bei 42 Klebern zur Anwendbarkeit der Direkt-Thermodesorption (dynamische Headspace-Methode) als Screening-Verfahren. Des weiteren wurden Versuche durchgeführt, um die Auswirkungen unterschiedlicher Probenherstellung (Trägermaterial, Auftragsmenge, Auftragsart) auf die Emissionen aus den Fußbodenklebern abschhätzen können. Die durchgeführten Untersuchungen stellen eine Grundlage zur Erarbeitung eines Umweltzeichens für Fußbodenkleber dar.