Filtern
Dokumenttyp
Sprache
- Englisch (4)
Schlagworte
- Bacteria (1)
- Benchmark (1)
- Carlsbergite (1)
- Computational (1)
- EBSD (1)
- Escherichia coli (1)
- Graphene oxide (1)
- Iron meteorites (1)
- Metal ordering (1)
- Rhabdite (1)
- Schreibersite (1)
- Shell buckling (1)
- Simulation (1)
- Structure determination (1)
- Surface charge (1)
- Synchrotron radiation (1)
- TEM (1)
- Wind turbine tower (1)
- X-ray computed tomography (1)
- XPS (1)
- dXCT (1)
Organisationseinheit der BAM
A survey is presented on some characteristic features of meteoritic (Fe,Ni)3P which is an abundant and important minor phase of most iron meteorites. This mineral (named schreibersite/rhabdite) plays a decisive role during the formation of the so-called Widmanstätten pattern. Different transmission as well as scanning electron microscopic techniques have been applied to get more precise information about the real structure of the phosphide crystals, their chemical composition and the metal distribution across the phoshide/ kamacite interface. X-ray crystal structure determinations have been performed for selected (Fe,Ni)3P - cystals from various iron meteorites (Toluca, North Chile, Watson, Orange River, Morasko, Agpalilik, Odessa, Canyon Diablo). These experiments revealed a metal ordering, i.e. for the three non-equivalent metal positions a different substitution of Fe by Ni has been found. The perfection of the brittle (Fe,Ni)3P samples differs appreciably and seems to be dependent on the thermal history of each individual meteorite. Moreover, inside Ni-rich rhabdite crystals small monocrystalline inclusions of CrN (carlsbergite) have been detected.
Aiming at the overall negative surface charge of bacteria, a new strategy of antibacterial agents based on large polymer-modified graphene oxide (GO) sheets is assessed. The presented flexible, polycationic Sheets match the size and charge density of the Escherichia coli surface charge density (2 × 1014 cm−2). These matching parameters create an unspecific but very strong bacteria adsorber by multivalent, electrostatic attraction.
Their interaction with bacteria is visualized via atomic force and confocal microscopy and shows that they effectively bind and wrap around E. coli cells, and thereby immobilize them. The incubation of Gram-negative and -positive bacteria (E. coli and methicillin-resistant Staphylococcus aureus, MRSA) with these polycationic sheets leads to the inhibition of proliferation and a reduction of the colony forming bacteria over time.
This new type of antibacterial agent acts in a different mode of Action than classical biocides and could potentially be employed in medicinal, technical, or agriculture applications. The presented microsheets and their unspecific binding of cell interfaces could further be employed as adsorber material for bacterial filtration or immobilization for imaging, analysis, or sensor technologies.
An assessment of the elastic-plastic buckling limit state for multi-strake wind turbine support towers poses a particular challenge for the modern finite element analyst, who must competently navigate numerous modelling choices related to the tug-of-war between meshing and computational cost, the use of solvers that are robust to highly nonlinear behaviour, the potential for multiple near-simultaneously critical failure locations, the complex issue of imperfection sensitivity and finally the interpretation of the data into a safe and economic design.
This paper reports on an international ‘round-robin’ exercise conducted in 2022 aiming to take stock of the computational shell buckling expertise around the world which attracted 29 submissions. Participants were asked to perform analyses of increasing complexity on a standardised benchmark of an 8-MW multi-strake steel wind turbine support tower segment, from a linear elastic stress analysis to a linear bifurcation analysis to a geometrically and materially nonlinear buckling analysis with imperfections. The results are a showcase of the significant shell buckling expertise now available in both industry and academia.
This paper is the first of a pair. The second paper presents a detailed reference solution to the benchmark, including an illustration of the Eurocode-compliant calibration of two important imperfection forms.
The lack of traceability to meter of X-ray Computed Tomography (CT) measurements still hinders a more extensive acceptance of CT in coordinate metrology and industry. To ensure traceable, reliable, and accurate measurements, the determination of the task-specific measurement uncertainty is necessary. The German guideline VDI/VDE 2630 part 2.1 describes a procedure to determine the measurement uncertainty for CT experimentally by conducting several repeated measurements with a calibrated test specimen. However, this experimental procedure is cost and effort intensive. Therefore, the simulation of dimensional measurement tasks conducted with X-ray computed tomography can close these drawbacks. Additionally, recent developments towards a resource and cost-efficient production (“smart factory”) motivate the need for a corresponding numerical model of a CT system (“digital twin”) as well. As there is no standardized procedure to determine the measurement uncertainty of a CT system by simulation at the moment, the project series CTSimU was initiated, aiming at this gap. Concretely, the goal is the development of a procedure to determine the measurement uncertainty numerically by radiographic simulation. The first project (2019-2022), "Radiographic Computed Tomography Simulation for Measurement Uncertainty Evaluation - CTSimU" developed a framework to qualify a radiographic simulation software concerning the correct simulation of physical laws and functionalities. The most important outcome was a draft for a new guideline VDI/VDE 2630 part 2.2, which is currently under discussion in the VDI/VDE committee. The follow-up project CTSimU2 "Realistic Simulation of real CT systems with a basic-qualified Simulation Software" will deal with building and characterizing a digital replica of a specific real-world CT system. The two main targets of this project will be a toolbox including methods and procedures to configure a realistic CT system simulation and to develop tests to check if this replica is sufficient enough. The result will be a draft for a follow-up VDI/VDE guideline proposing standardized procedures to determine a CT system's corresponding characteristics and test the simulation (copy) of a real-world CT system which we call a "digital twin".