Filtern
Dokumenttyp
- Vortrag (11)
Referierte Publikation
- nein (11)
Schlagworte
- Ecotoxicity (4)
- HP14 (3)
- Recycling materials (3)
- DSLT (2)
- Leaching (2)
- Auswaschung (1)
- Bauprodukte (1)
- Bioavailability (1)
- Construction products (1)
- Düngemittel (1)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (11) (entfernen)
Flame retardants are increasingly used in consumer products as e.g. electronics and furniture as well as in construction. Along with the increased usage, concerns about negative effects of flame retardants on human health and the environment have been raised. Concerning construction products one application for flame retardants is the furnishing of steel structures with reactive flameproof coatings. These coatings consist of a complex mixture of different chemicals, additives and solvents. For the evaluation of the risk possibly posed by their application to the environment, this whole mixture should be tested.
Two different leaching tests were applied according to DIN/TS 16637-2 (sample permantly submerged in water) and DIN EN 16105 (immersion and drying cycles), respectively, which can be used for plate-like products. Eluates were divided into subsamples for the measurement of different parameters: pH-value, conductivity, total organic carbon (TOC), cation and anion concentration. For screening of organic compounds, aqueous samples were liquid/liquid extracted using three solvents with different polarity (toluene, hexane and ethylacetate). GC-MS chromatograms were recorded in the SCAN mode and mass spectra of the peaks were compared with spectras stored in the NIST library.
Eluates of leaching test accroding to DIN CEN TS 16637-2 showed low electrical conductivity (20 to 150 µS/cm) and low release of cation and anions often near the LOQ. Diffferences could be observed for plates treated with the reactive coating at both sides and plates coated only at one side, while the other side is only furnished by the corrosive protection layer. Release of TOC and Zn was approx twice or 10 fold higher in the case of plates coated on one side. Furthermore, the comparison of the results for both types of plates showed that a large portion of the released compounds originate rather from the corrosion protection layer than from the reactive coating itself. Leaching tests according to DIN EN 16105 have not been finished yet, but first results show that the conductivity is much lower (1-4 µS/cm) than for the tests according to DIN/TS 16637-2 leading to the assumption that the release of compounds is lower.
By comparison of the mass spectra with library data, mainly organic solvents as xylene, 1-methoxy-2-propanol acetate and n-btuyl carbamate have been tentatively identified so far in the first test fraction done by DIN CEN TS 16637-2.
Reaktive Flammschutzbeschichtungen bilden im Brandfall einen wärmeisolierenden Schaum, der die Stahlträger schützt. Diese Beschichtungen erhalten eine komplexe Mischung aus verschiedenen Chemikalien wie Additiven, Füllstoffen und Lösungsmitteln, die bei Kontakt mit Wasser freigesetzt werden können. Für eine Beurteilung der Auswirkung der auswaschbaren Substanzen auf die Umwelt sollte die gesamte Mischung und nicht nur Einzelkomponenten herangezogen werden. Ziel der vorgestellten Untersuchung war es die Frage zu klären, ob Elutionsverfahren in Kombination mit ökotoxikologischer Testung verwendet werden können, um eine Gefährdung der Umwelt auszuschließen.
Das Freisetzungspotential aus den drei Beschichtungen wurde mit Hilfe von zwei verschiedenen Elutionsverfahren nach DIN/TS 16637-2 (Probe ist permanent in Wasser getaucht) und DIN EN 16105 mehrere (Immersions- und Trocknungszyklen) untersucht. Neben chemischen Parametern (pH-Wert, Leitfähigkeit, Gesamtkohlenstoff, Kationen- und Anionenkonzentration und ein Screening auf organische Substanzen), wurde auch die Wirkung auf verschiedene Organismen (Algen, Daphnien, Fischembryonen und Leuchtbakterien) und die Gentoxizität (AMES) untersucht.
Insgesamt zeigen die Eluate keine bis moderate Toxizität, wobei ein Produkt eine deutlich höhere Toxizität als die anderen beiden Produkte aufweist. Die Eluate zeigen insgesamt eine geringe Leitfähigkeit von 20 bis 150 µS/cm und eine geringe Freisetzung von Kationen und Anionen, die oft unter oder in der Nähe der Bestimmungsgrenze liegen. Lediglich Zink, Barium und Phosphat konnten in nahezu allen Fraktionen des Tests nach DIN/TS 16637-2 nachgewiesen werden. Im Gegensatz dazu lag Phosphat in den Fraktionen des intermittierenden Tests unter der Nachweisgrenze. Dies ist wahrscheinlich auf die kürzere Kontaktzeit zurückzuführen. Die Barium und Zinkkonzentrationen sind ebenfalls geringer im Vergleich zum DIN/TS 16637-2. Das Konzentrationsprofil der DOC-Konzentration ist für die beiden Tests ebenfalls unterschiedlich: im intermittierenden Test sinkt die Konzentration mit den Immersionszyklen, während bei dem Test mit ständigen Tauchen die Konzentration in den letzten Fraktionen steigt. Ein Vergleich der Ökotoxizität der ersten Fraktionen und der Fraktion 7 zeigt, dass diese ebenfalls ansteigt.
Die Kombination der beiden Tests ermöglicht es, nach Produkten mit einem größeren und kleineren Risiko für die Umwelt zu unterscheiden. Allerdings müssen die Fraktionen, die für diese Testung ausgewählt werden je nach Elutionstest, Verwendungsszenario und Konzentrationsprofil der Analyten sorgfältig ausgewählt werden.
The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail.
The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail.
The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail.
Ausgewählte Ergebnisse des UBA-Vorhabens "Beregnete Bauteile und Bauprodukte: Entwicklungen für Vergabegrundlagen für den Blauen Engel mit Hilfe von Auslaugtest" werden für organische und anorganische Analyten präsentiert. Ein Schwerpunkt ist den Einfluss der verschiedenen Schichten von WDVS-Systemen aufzuzeigen.
Construction products are complex materials and contain a large number of different chemicals, which might be released to the environment during usage. Depending on the compound and on the matrix only a small portion is transferred to environment and therefore a risk assessment should be based on the available portion. Concerning the pathway to soil and groundwater by contact with rain or seepage water leaching tests were developed and standardized by CEN to determine the release potential of construction products. Chemical analysis in the eluates can be combined with eco-toxicological testing. In this presentation an overview about existing leaching methods is given using selected examples of our work. We especially draw the attention to research which is still needed to close the gap between the results of leaching experiments and the subsequent risk assessment of the products.
The eluates of 15 paints for outdoor use were used for a screening of organic compounds and the concentration of cations and anions were determined. Concerning the inorganic constituents only a small number of elements were present with concentrations higher than the limit of detection. Thus, leaching of potential hazardous chemicals is probably of higher concern. Several glycol ethers, polyalkylene glycols and some surfactants and coalescing agents have been identified. Among these only the latter are classified as hazardous to aquatic organisms. The identification of the organic compounds is a time consuming and labor-intensive step due to the high number of chemicals produced and used. Using eco-toxicity tests provides information on the environmental risk without the need for of chemical identification of all compounds. The screening of a set of construction products shows that only a part of eluates causes adverse effects in the test and that such screening can be used as a first step in the assessment of construction products. If this kind of testing is included in the evaluation concept an in depth chemical analysis is only needed for products showing adverse effects.
Determination of the eluate concentration after leaching enables to determine the potential release to the environment and to focus on the available fraction. However, limit values or other concepts to use this information in risk assessment are still missing.