Filtern
Dokumenttyp
- Zeitschriftenartikel (8)
- Beitrag zu einem Tagungsband (3)
- Posterpräsentation (2)
- Vortrag (1)
- Sonstiges (1)
Sprache
- Englisch (15)
Schlagworte
- Hydrogen (4)
- Mechanical properties (3)
- Composites (2)
- Elastomers (2)
- Electrospinning (2)
- 2D filler (1)
- AFM (1)
- AFM force spectroscopy (1)
- Acrylonitrile Butadiene rubber (1)
- Acrylonitrile butadiene rubber (1)
Organisationseinheit der BAM
Eingeladener Vortrag (wissenschaftliche Konferenzen)
- nein (1)
Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to study deeply material compatibility, in particular polymer materials that are directly in contact with hydrogen. This paper presents an experimental study on the fretting wear behavior of two types of cross-linked hydrogenated acrylonitrile butadiene rubbers against 316L steel ball in hydrogen environment. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen. the influences of hydrogen pressure as well as the aging exposure on the fretting behavior are discussed by means of surface analyses along with the material properties.
The development of a robust hydrogen infrastructure poses challenges to materials exposed to high pressurized hydrogen environments. Polymeric materials, which are expected to perform as seals, gaskets, O-rings, hoses among other applications face high risk of damage due to rapid gas decompression (RGD) which might cause operational safety issues. In this study, we intend to assess the effects of a high pressurized hydrogen environment on carbon black filled (CB) elastomers. The materials were exposed to 100 MPa hydrogen atmosphere at room temperature and at 85°C. Ex-situ characterization was performed during the first 30 minutes after decompression and repeated two days after the exposure when total gas desorption has taken place. The physical and mechanical characteristics of the materials were determined by means of density and volume change, hardness and tensile tests, and dynamic mechanical analysis.
Effect of high-pressure hydrogen environment on the physical and mechanical properties of elastomers
(2024)
This study presents the influence of high-pressure hydrogen environment on the physical and mechanical properties of two types of cross-linked hydrogenated acrylonitrile butadiene rubbers. Based on the CSA/ANSI standard, static exposures in hydrogen experiments were performed up to 100 MPa at 120 °C. Characterization before and after exposure was conducted by means of density and hardness measurements, dynamic mechanical analysis (DMA), tensile tests, compression set, FT-IR and AFM analyses to assess effects after decompression. While the effect of high-pressure exposure is significant immediately after exposure, most of the physical and mechanical properties recover after 48 hours. FT-IR, AFM, SEM and compression set results indicate, however, permanent effects.
Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to deeply study material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical parts are sealing materials that need increased safety requirements. In this study, the fretting behavior of several elastomer materials were evaluated against 316L stainless steel in an air and hydrogen environment up to 10 MPa. Several grades of cross-linked hydrogenated acrylonitrile butadiene (HNBR), acrylonitrile butadiene (NBR) and ethylene propylene diene monomer rubbers (EPDM) were investigated. Furthermore, aging experiments were conducted for 7 days under static contions in 100 MPa of hydrogen followed by rapid gas decompression. Fretting tests revealed that the wear of these compounds is significantly affected by the hydrogen environment compared to air, especially with NBR grades. After the aging experiment, the friction response of the HBNR grades is characterized by increased adhesion due to elastic deformation, leading to partial slip.
Effects of NBR formulations on properties for high-pressure gas systems were tested. Functionalized silica enhances typical properties to a comparable range like CB. The balance of additives results in suitable RGD performance. Silica filled NBR shows lower H2 uptake compared to non-plasticized CB filled NBR. Morphology of CB filled NBR is less affected by H2 than silica filled grades.
In this contribution, the sliding performance of newly formulated polymer materials with improved sustainability are investigated and compared with conventional materials. Tribological tests were performed in hydrogen at ambient temperature as well as cryogenic medium. The samples were arranged in a pin-on-disk configuration with a flat pin sliding against a rotating austenitic steel disk. The friction and wear mechanisms are described and discussed by means of surface analyses.
As the transition towards the usage of renewable energy is getting urgent, the fluctuations of clean energy production require efficient storage alternatives. Hydrogen offers not only the possibility of energy storage but also, acts as an energy carrier. It is then important to study the effect of highly pressurized hydrogen atmosphere on the materials destinated for its storage and transport, in order to assure the reliable performance of the sealing materials containing hydrogen. In this study, a set of carbon black (CB) filled rubbers comprising hydrogenated acrylonitrile butadiene rubber (HNBR), acrylonitrile butadiene rubber (NBR) and ethylene propylene diene monomer rubber (EPDM) was tested under high pressure hydrogen atmosphere (1000 bar) and at different temperature conditions: 120°C for HNBR, room temperature and 85°C for NBR and EPDM. The influence of hydrogen on the materials properties was measured after 7 days of exposure under hydrogen and evaluated again after 48h. Density and volume change, as well as hardness, tensile tests, compression set, dynamic mechanical measurements and infrared spectroscopy evaluations were conducted to estimate the impact of high-pressure hydrogen on the rubber grades. Our study reveals, an effect on the physical and mechanical properties, possibly related to small changes in the matrix-filler interaction after the hydrogen exposure. All materials, however, show a trend to recover most of their properties 48h after hydrogen exposure.
This study investigates the effect of the addition of a 2D filler (Struktosil) to a carbon black-filled acrylonitrile butadiene rubber, developed for seals in hydrogen applications. Several characterization methods have been adopted. The addition of Struktosil increases the stiffness of the material up to a strain of about 100%, to a lesser extent in presence of a plasticizer. The dissipative response of the material is increased by Struktosil addition and decreased in presence of the plasticizer. Concerning fracture behaviour, the crack initiation and Rapid Gas Decompression (RGD) resistance were not affected by the addition of Struktosil but decreased in presence of plasticizer. Furthermore, the addition of Struktosil had a positive effect on crack propagation resistance. The effects of pressurized hydrogen exposure on physical-mechanical properties were also evaluated and correlated with the results. A correlation between fracture toughness and RGD resistance has been also attempted.
Materialien auf PTFE-Basis werden in der Regel als Kolbenringe in Hochdruck- und/oder kryogenem Wasserstoff verwendet. In diesem Projekt werden neu formulierte und nachhaltigere Polymerwerkstoffe mit herkömmlichen Materialien verglichen. Auf Grundlage der tribologischen Ergebnisse werden vielversprechende Kandidaten zusammen mit Reibungsmechanismen sowohl bei Hochdruck- als auch bei Niedrigtemperatur-Wasserstoff vorgeschlagen.
The image designed by Natalia Cano Murillo and colleagues shows the cross section of a ternary composite (boehmite/polycarbonate/epoxy, 80μm x 80μm). The surface was measured by AFM kelvin probe microscopy, yielding the surface potential which is shown as 3D‐surface and contour lines. The sample was further subjected to AFM force spectroscopy with a lateral resolution of 1μm², yielding the local Young's modulus, projected in false colors on the 3D surface. The ternary system, containing boehmite nanoparticles, shows a broad distribution of modulus, desirable for optimized macroscopic mechanical properties, such as high stiffness as well as toughness.
