Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (17)
- Beitrag zu einem Tagungsband (7)
- Forschungsbericht (6)
- Beitrag zu einem Sammelband (3)
- Monografie (1)
- Posterpräsentation (1)
- Forschungsdatensatz (1)
Schlagworte
- Resistance spot welding (6)
- Advanced high strength steels (4)
- Fatigue (3)
- High strength steels (3)
- Weldbonding (3)
- CONSENS (2)
- Lightweight body shell design (2)
- Process reliability (2)
- Spot welding (2)
- Widerstandspunktschweißen (2)
Organisationseinheit der BAM
Für die Sicherheit und Gebrauchstauglichkeit von geschweißten Behältern mit Aufdachungen unter Innendruck müssen die Biegezusatzspannungen berechnet oder wirklichkeitsnah abgeschätzt werden. Dazu können verschiedene Verfahren herangezogen werden, die sich in Aufwand, Genauigkeit und zeitlicher Verfügbarkeit des Ergebnisses unterscheiden. Beim Entwurf von Behältern, im Betrieb oder im Schadensfall kommen sie zum Einsatz.
Calculation of ultrasonic reflection and transmission in anisotropic austenitic layered structures
(1999)
Characterization of the microstructure of high-chromium cast irons using Mössbauer spectroscopy
(2001)
The finish grinding process for cement materials uses ball mills with differently sized grinding balls. Because the grinding takes place through the impact and friction of the balls, balls with a high wear resistance are desirable and the materials of choice are the high-chromium white cast irons. This article examines the behavior of these cast irons when subjected to various heat treatments. The emphasis is on the dependence of the microstructure properties on the chemical composition of the alloys and the heat treatment parameters. The content of retained austenite and that of carbon in the martensite phase were determined by the use of Mössbauer spectroscopy. The results verify that a higher proportion of retained austenite with low carbon content and a martensite with higher hardness produce a material with good fracture toughness and resistance to abrasive wear.
In lightweight car body shell mass production, due to requirements on vehicle weight reduction and carbon dioxide emissions, joining of advanced high strength steels (AHSS) with different joining procedures and especially hybrid bonding techniques is becoming more and more important. One of these hybrid bonding techniques is the combination of resistance spot welding and adhesive bonding called weldbonding. One of the important advantages of weldbonded joints in comparison to resistance spot welded joints are the enhanced mechanical properties. To guarantee sufficiently high quality conditions regarding the strength of the weldbonded joints, the influences of the applied adhesive systems and of different base metal combinations are studied. This is carried out for both non-corrosive and corrosive environments and for the choice of different joining parameters settings. In particular, the mechanical behaviour of the weldbonded joints is investigated under quasi-static, impact and fatigue loads. Furthermore, the energy absorption of the weldbonded joints for both non-corrosive and corrosive environments is studied. It is shown that the weldbonded joints possess higher mechanical strengths in all load cases (quasi-static, impact and fatigue). Corrosive attack affects weldbonded joints, and the quasi-static strength is reduced. Resistance spot welded joints are not affected by the corrosive attack, but even after several weeks of corrosive attack, the quasi-static strength of weldbonded joints remains higher than that of resistance spot welded joints.
For spot-welded joints, the resistance to
mechanical stress depends on the local strength properties
and gradients in the weld area. The commonly used
methods for investigating the stress–strain behaviour across
the weld area are connected with a high level of sample
preparation and with considerable limitations in local resolution.
A promising method for determining locally
resolved stress–strain curves is the instrumented indentation
test in connection with the method of representative
stress and strain (RS) and the method of artificial neural
networks (NNs). The stress–strain properties of the weld
nugget and the base metal determined by these two methods
are compared and discussed, additionally in relation to
the stress–strain curves obtained from the tensile test. The
measured Vickers hardness across the weld area is compared
with the evaluated local stress–strain properties.
Three steels used in automobile manufacturing are investigated:
mild steel DC04 and two advanced high-strength
steels (TRIP steel HCT690T and martensitic steel HDT
1200M). The results of the two methods (RS and NN) show
good correspondence for the base metal area but some
significant differences for the weld nugget. Comparing the
data across the weld area, no evidence of the presence of
residual stress (which would influence the results) was
found.
Methods to obtain weld discontinuities in spot-welded joints made of advanced high-strength steels
(2011)
Resistance spot welding is the major joining technique in mass car production. This applies in particular to high-strength steel and advanced high-strength steel (AHSS) joining of thin sheet steel components for lightweight body shell structures. Joining of AHSS in mass production might lead to weld discontinuities under certain circumstances. Those discontinuities in form of cracks might be an initial start of cracking in the spot-welded joints regarding fatigue loads. It is of great interest to figure out, if, in comparison to specimens without weld discontinuities, the crack initiating point changes and if the fatigue resistance might be reduced by the discontinuities. In this contribution, an overview of potential discontinuities is given. Their possible causes are discussed and means for their detection are highlighted. Among the possible causes of weld discontinuities, two major groups are distinguished: the welding parameters as primary influences in the welding process, and the production-specific influences as secondary ones. With emphasis on major cracks penetrating the weld nugget, these influences are analysed. Finally, a combination of extreme welding parameters with production-specific influences is chosen in order to establish a method which enables the preparation of fatigue test specimens with reproducible major cracks in different locations of the spot-welded joints. This method is than applied in order to prepare spot weld specimens for fatigue tests.
Study of fatigue behavior for spot welded tensile shear specimens of advanced high strength steels
(2012)
For automotive body-in-white applications the influence of manufacture-related gaps between the steel sheets and also of manufacture-related surface cracks on the fatigue behavior of tensile shear specimens for spot welded TRIP steel was analyzed. It was shown that gaps between the steel sheets reduce the fatigue strength, whereas the fatigue behavior is neither influenced by cracks in the electrode indentation area nor in the heat effected zone.
In this study, the influence of production-related gaps on the shear tension strength and fatigue performance was investigated for resistance spot welded TRIP steel HCT690. Furthermore, the local strain distribution in shear tension test was calculated by the digital image correlation technique (DIC). The static shear tension strength was found to be almost independent of gaps up to 3 mm. The maximum local strain in the spot weld region however decreases depending on which sample side (deformed or undeformed) is considered. In addition, it has been ascertained that gaps of 3 mm lead to a significant drop in fatigue life compared to gap-free shear tension samples. This fact could be attributed to decreased stiffness, higher transverse vibration and higher rotation (θ) between the sheets as well as increased local stress calculated by 2 dimensional FE simulation.
For the designing of safety-relevant components particularly by means of finite element calculations, great significance is attached to the determination of local material parameters in the welding region. Conventional test methods can merely provide global parameters which, however, are frequently not sufficient precisely for the calculation of resistance-spot-welded components since these are characterised by the existence of joining zones with tight local limitations. In contrast, modern test methods such as optical strain field measurement permit the determination of the characteristic material data for concrete locations and times. In order to establish the potential of optical strain field measurements for the characterisation of the local material behaviour of spotwelded joints, tensile shear tests as well as tensile tests were carried out on resistance-spot-welded high-strength steels. The results show the high potential of this procedure not only for the quantification of the local strain behaviour in the joining region but also for the determination of local characteristic material data.
In the lightweight body shell mass production of automobiles, the application of hybrid bonding techniques becomes more and more important. Especially the combination of adhesive bonding and resistance spot welding called weldbonding is of great importance. The target of this contribution is to show the influence of medium-viscosity and low-viscosity structural adhesives on the process reliability of the weldbonding process and the mechanical properties of the hybrid bonded joints. The given results are based on the application of an epoxy PUR-based, an epoxy resin-based and a rubber-based adhesive system for joining a mild and some different advanced high strength steels (AHSS). It will be shown that both the process reliability of the weldbonding process and the mechanical behaviour of the weldbonded joints are influenced by the combinations of the base metals, the applied adhesive systems and the choice of the joining parameters. The behaviour of the weldbonded joints will be studied under quasi-static and impact loads. The discussion of the metallurgical structure of the weldbonded joints depending on the joining parameters will be given, too. Furthermore, the fatigue behaviour of the weldbonded joints will be studied.